Lochinvar 1.5 User manual

Brand: Lochinvar

Model: 1.5

Category: Navigators

Type: User manual

Service Manual

Models: 1.5 - 2.0 - 2.5 - 3.0 - 3.5

This manual must only be

used by a qualified heating

installer / service technician.

Read all instructions,

including this manual and

the Crest Installation and

Operation Manual, before

installing. Perform steps in

the order given. Failure to

comply could result in severe

personal injury, death, or

substantial property damage.

 WARNING

Save this manual for future reference.

FB-SER Rev B

Hazard definitions

The following defined terms are used throughout this manual to bring attention to the presence of hazards of various risk levels or

to important information concerning the life of the product.

 DANGER

 WARNING

 CAUTION

CAUTION

NOTICE

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious

injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious

injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate

injury.

CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not

avoided, may result in property damage.

NOTICE indicates special instructions on installation, operation, or maintenance that are important but not

related to personal injury or property damage.

CONTENTS ........................................................................ 2

Hazard Definitions .............................................................. 2

PLEASE READ BEFORE PROCEEDING ........................ 3

Handling Ceramic Fiber Materials ...................................... 3

When servicing boiler ................................................... 4

Boiler operation ............................................................ 4

Boiler water ................................................................... 4

Freeze protection fluids ................................................ 4

WHAT IS IN THIS MANUAL .............................................. 5

1. SERVICE

Boiler Piping ....................................................................... 6

SMART TOUCH Display (Home Screen) .......................... 7

Control Inputs ............................................................... 8

Control Outputs ............................................................. 9

General Operation ................................................. 10-11

Table 1A - Sequence of Operation .................................. 12

Table 1B - Parameter Table ........................................ 13-17

Viewable and Changeable Control Parameters .......... 18-25

Cascade Screen ............................................................... 26

Graph Screen ................................................................... 27

History Screen ............................................................. 28-29

Service Screen ................................................................. 30

2. MAINTENANCE

Maintenance and Annual Startup ................................ 31-35

3. TROUBLESHOOTING

Before Troubleshooting .................................................... 36

Check Control Module Fuses .......................................... 36

Table 3A - Troubleshooting Chart - No Display ............... 37

Checking Temperature Sensors ...................................... 38

Table 3F - Troubleshooting Chart - Noisy System .......... 39

Table 3G - Troubleshooting Chart - Fault Messages . 40-51

Combustion Analysis Procedure ...................................... 52

Table 3H - Troubleshooting Chart - Combustion Levels 52

Table 3I - Flue Products ................................................... 52

Gas Valve Adjustment Procedure .................................... 53

Revision Notes .................................................. Back Cover

Contents

Service Manual

Please read before proceeding

Installer – Read all instructions, including

this manual and the Crest Installation

and Operation Manual, before installing.

Perform steps in the order given.

User – This manual is for use only by

a qualified heating installer/service

technician. Refer to the Crest User’s

Information Manual for your reference.

Have this boiler serviced/inspected by

a qualified service technician at least

annually.

Failure to comply with the above could

result in severe personal injury, death or

substantial property damage.

When calling or writing about the boiler

– Please have the boiler model and serial

number from the boiler rating plate.

Consider piping and installation when

determining boiler location (see the Crest

Installation and Operation Manual).

Any claims for damage or shortage

in shipment must be filed immediately

against the transportation company by the

consignee.

Handling ceramic fiber materials

REMOVAL OF COMBUSTION CHAMBER LINING

The combustion chamber insulation in this appliance contains ceramic fiber material. Ceramic fibers can

be converted to cristobalite in very high temperature applications. The International Agency for Research

on Cancer (IARC) has concluded, “Crystalline silica in the form of quartz or cristobalite from occupational

sources is carcinogenic to humans (Group 1).” Normal operating temperatures in this appliance are below

the level to convert ceramic fibers to cristobalite. Abnormal operating conditions would have to be created

to convert the ceramic fibers in this appliance to cristobalite.

The ceramic fiber material used in this appliance is an irritant; when handling or replacing the ceramic

materials it is advisable that the installer follow these safety guidelines.

Avoid breathing dust and contact with skin and eyes.

• Use NIOSH certified dust respirator (N95). This type of respirator is based on the OSHA

requirements for cristobalite at the time this document was written. Other types of respirators may

be needed depending on the job site conditions. Current NIOSH recommendations can be found on

the NIOSH website at http://www.cdc.gov/niosh/homepage.html. NIOSH approved respirators,

manufacturers, and phone numbers are also listed on this website.

• Wear long-sleeved, loose fitting clothing, gloves, and eye protection.

Apply enough water to the combustion chamber lining to prevent airborne dust.

 Remove the combustion chamber lining from the appliance and place it in a plastic bag for disposal.

 Wash potentially contaminated clothes separately from other clothing. Rinse clothes washer

thoroughly.

NIOSH stated First Aid.

 Eye: Irrigate immediately.

 Breathing: Fresh air.

 WARNING

NOTICE

 WARNING

Service Manual

Please read before proceeding

When servicing boiler –

• To avoid electric shock, disconnect electrical supply

before performing maintenance.

• To avoid severe burns, allow boiler to cool before

performing maintenance.

Boiler operation –

• Do not block flow of combustion or ventilation air to

the boiler.

• Should overheating occur or gas supply fail to shut off,

do not turn off or disconnect electrical supply to

circulator. Instead, shut off the gas supply at a location

external to the appliance.

• Do not use this boiler if any part has been under water.

The possible damage to a flooded appliance can be

extensive and present numerous safety hazards. Any

appliance that has been under water must be replaced.

Boiler water –

• Thoroughly flush the system (without boiler

connected) to remove sediment. The high-efficiency

heat exchanger can be damaged by build-up or

corrosion due to sediment.

• Do not use petroleum-based cleaning or sealing

compounds in the boiler system. Gaskets and seals in

the system may be damaged. This can result in

substantial property damage.

• Do not use “homemade cures” or “boiler patent

medicines”. Serious damage to the boiler, personnel,

and/or property may result.

• Continual fresh make-up water will reduce boiler life.

Mineral buildup in the heat exchanger reduces heat

transfer, overheats the stainless steel heat exchanger, and

causes failure. Addition of oxygen carried in by makeup

water can cause internal corrosion. Leaks in boiler

piping must be repaired at once to prevent the

introduction of makeup water.

Freeze protection fluids –

• NEVER use automotive antifreeze. Use only inhibited

propylene glycol solutions which are specifically

formulated for hydronic systems. Ethylene glycol is

toxic and can attack gaskets and seals used in hydronic

systems.

Service Manual

What is in this manual?

Service

Near boiler piping

• Typical system components

The Crest boiler display

• Display panel readout, buttons and their functions

Control module inputs

• Control module inputs and options

Control module outputs

• Control module outputs and options

General

• How the boiler operates

• How the control module operates

• Access modes -- user and installer

• Sequence of operation -- HWG/space heating

Control panel menu access

• Accessing programming mode and locating menus

(See separate guide covering the PC interface.)

Control panel parameter access

• Accessing and changing parameters from the display panel

Quick start information -- parameter

table

• An index of available adjustments and readouts, where to

access them and where to find detailed information.

Crest boiler operation

• Initial Setup

• Set Points

• Outdoor Reset

• Ramp Delay

• BMS

• Advanced Setup

• SH Night Setback

• HWG Night Setback

• Cascade

• Pumps

• Service Notification

Maintenance

• Service and maintenance schedules

• Address reported problems

• Inspect boiler area and boiler interior

• Clean condensate trap

• Check all piping for leaks

• Check air openings

• Flue vent system and air piping

• Check water system

• Check expansion tank

• Check boiler relief valve

• Inspect ignition electrode

• Check ignition ground wiring

• Check all boiler wiring

• Check control settings

• Perform start-up and checks

• Check burner flame

• Check flame signal

• Check flue gas temperature

• General maintenance

• Review with owner

• Cleaning boiler heat exchanger

• Oiled bearing circulators

Troubleshooting

• Troubleshooting table - No display

• Checking temperature sensors

• Sensor tables

• Troubleshooting table - Fault messages displayed on

boiler interface

• Combustion analysis procedure

• Gas valve adjustment procedure

1 Service

Service Manual

Boiler piping

This piping reference is included to specify the Boiler Piping specific to the Crest boiler. This piping scheme is important for

proper operation of the SMART TOUCH control. See the Crest Installation and Operation Manual for more detailed piping

diagrams.

Single Boiler - Recommended - Primary / Secondary Piping with a Hot Water Generator

HOT WATER

GENERATOR

WATER

GENERATOR

CIRCULATOR

BOILER PUMP

FLOW CHECK

VALVE (TYPICAL)

Y-STRAINER

(RECOMMENDED)

RELIEF

VALVE

BALL VALVE

(TYPICAL)

AIR SEPERATOR

DRAIN PORT

(TYPICAL)

SYSTEM

CIRCULATOR

BACK FLOW

PREVENTER

PRESSURE

REDUCING VALVE

PRESSURE

GAUGE

EXPANSION

TANK

12"

MAX

FROM SYSTEM

TO SYSTEM

MAKE UP

WATER

BOILER

DRAIN

SYSTEM RETURN

SENSOR

SYSTEM SUPPLY

SENSOR

Y-STRAINER

(RECOMMENDED)

RELIEF

VALVE

BALL VALVE

(TYPICAL)

AIR SEPERATOR

DRAIN PORT

(TYPICAL)

SYSTEM

CIRCULATOR

BACK FLOW

PREVENTER

PRESSURE

REDUCING VALVE

PRESSURE

GAUGE

EXPANSION

TANK

FROM SYSTEM

TO SYSTEM

MAKE UP

WATER

BOILER DRAIN

Single Boiler - Alternate - Full Flow System Piping

Service Manual

1 Service (continued)

Outlet Water Temperature - This is the boiler outlet

temperature.

Inlet Water Temperature - This is the boiler inlet temperature.

System Supply Temperature - This is the water temperature

as measured by the system supply sensor located in the

downstream piping (if connected).

System Return Temperature - This is the water temperature

measured by the system return sensor located in the upstream

piping (if connected).

Outside Air Temperature - This is the outdoor air temperature

(if connected).

HWG Temperature - This is the temperature as measured by

the tank sensor in the hot water storage tank (if connected).

Flue Temperature - Temperature measured by the flue sensor.

Time - The time is displayed in the lower left-hand corner of the

display. Reference this manual for Night Setback parameters

and more information regarding adjusting the date and time.

Boiler Status button - Pressing this button brings up the Boiler

Status Screen. This screen shows the status of the various

safeties, inputs, and outputs to the control module. Reference

this manual for more information regarding this screen.

Main Menu button - Pressing this button brings up the Main

Menu Screen. From this screen navigation to nine (9) other

screens is possible.

Modulation button - Pressing this button brings up the

Modulation Screen. This screen shows overall boiler

modulation, individual fan speeds, and flame currents.

Modulation Percentage - Displays the current boiler firing

rate.

Home Screen

The Home Screen displays status, modulation rate, outlet water temperature, inlet water temperature, flue temperature, system

supply temperature, system return temperature, outdoor air temperature, and domestic hot water tank temperature.

The boiler can be started and stopped by pressing the ON/OFF button. The Boiler Status Screen and Main Menu Screen can be

accessed by pressing the appropriate button.

When the ON/OFF switch is turned to the ON position,

the first screen visible on the LCD display will be the Home

Screen. This screen displays the current status of the Crest

boiler. The following items can be viewed or interacted with

on the Home Screen:

On/Off button - Pressing this button allows the boiler to be

placed in either Manual Shutdown Mode or Standby Mode.

Status - This line shows the current operating status of the

Crest boiler and the current set point.

1 Service

Service Manual

1 Service

GAS PRESSURE SWITCHES

HWG THERMOSTAT /

SENSOR

ENABLING DEVICE

SYSTEM SENSOR -

SUPPLY

OUTDOOR SENSOR

SEQUENCER / BUILDING

MANAGMENT SYSTEM

LOW VOLTAGE

CONNECTION

BOARD

INLET TEMPERATURE

SENSOR

OUTLET TEMPERATURE /

HI-LIMIT SENSOR

FLUE GAS SENSOR

LOUVER PROVING SWITCH

FLAME SENSOR 1 & 2

LOW WATER CUTOFF

BLOCKED DRAIN SWITCH

DISPLAY PANEL

PC INTERFACE

SMART CONTROL

MODULE

AIR PRESSURE SWITCH

SYSTEM SENSOR -

RETURN

AUX SWITCH 1 & 2

0-10 INPUT FROM

SYSTEM PUMP

BLOWER PROVING

SWITCHES

CASCADE

INLET AIR SENSORS

MANUAL RESET

HIGH LIMIT

VENT DAMPER

PROVING SWITCH

MODBUS

BOARD

Control inputs

1 Service

Service Manual

1 Service (continued)

LOW VOLTAGE

CONNECTION

BOARD

SMART CONTROL

MODULE

ALARM CONTACTS

LOUVER RELAY

RUN TIME CONTACTS

SEQUENCER / BUILDING

MANAGMENT SYSTEM

BOILER PUMP

CONTACTOR

SYSTEM PUMP

CONTACTOR

HWG PUMP

CONTACTOR

IGNITOR

BLOWERS

GAS VALVES

BOILER RATE OUTPUT

DISPLAY PANEL

PC INTERFACE

120V

SUPPLY

SYSTEM PUMP BOILER PUMP DHW PUMP

MAX. 1.5 AMPS PER CONNECTION

FIELD SUPPLIED CONTACTOR MUST

BE INSTALLED

LINE VOLTAGE

TERMINAL

STRIP

0-10V OUTPUT TO

BOILER PUMP

VENT DAMPER

Control outputs

1 Service

Service Manual

General Operation

How the boiler operates

The Crest uses an advanced stainless steel heat exchanger

and electronic control module that allows fully condensing

operation. The blowers pull in air and push flue products out

of the boiler through the heat exchanger and flue piping. The

control module regulates blower speeds to control the boiler

firing rate. The gas valves sense the amount of air flowing into

the boiler and allow only the right amount of gas to flow.

How the control modules operate

The Crest boiler is equipped with a SMART TOUCH control

module. The SMART TOUCH control module receives inputs

from boiler sensors and external devices. The control module

activates and controls the blowers and gas valves to regulate heat

input and switches the boiler, Hot Water Generator (HWG),

and system pumps on and off as needed. The user programs

the control module to meet system needs by adjusting control

parameters. These parameters set operating temperatures and

boiler operating modes.

Sequence of operation

Table 1A (page 12) shows control module normal sequences of

operation for space heating and HWG operation. The combined

operation sequence is for a typical application, programmed to

provide HWG priority.

Access modes

User

The USER can adjust various space heating and HWG operating

variables:

- Navigate to the Initial Setup Screen (FIG. 1-5).

- From the Home Screen (FIG. 1-1), press MAIN

MENU, then press SETUP on the Main Menu

Screen (FIG. 1-2).

- Press ENTER on the Password Screen (FIG. 1-3)

(do not enter any values) and then press INITIAL

SETUP on the Setup Screen (FIG. 1-4).

The USER can set the date and time and adjust temperature set

points, and outdoor reset points.

Under the ADVANCED SETUP menu, the USER can change the

TEMPERATURE UNITS and the LCD BACKLIGHT TIMER.

Installer

Most parameters are available only to the INSTALLER, accessible

only by entering the installer password (5309) in the Password

Screen (see the User Section).

Figure 1-1 Home Screen

Figure 1-2 Main Menu Screen

Figure 1-3 Password Screen

Service Manual

1 Service (continued)

Saving parameters (reference the Parameter Table -

Table 1B on pages 13 - 17 of this manual)

To adjust and save parameters (reference FIG. 1-5):

To change a parameter, use the arrows next to the parameter

list on the Menu Screen to highlight the desired parameter,

then press SELECT. A short description of the parameter and

its current setting are then displayed on the bottom half of the

screen. To adjust the setting, use the buttons to the left and

right of the current setting.

Note: If the above mentioned buttons to adjust settings do

not appear, the correct PASSWORD has not been entered.

Press the SAVE button after adjusting a parameter value.

Additional parameter settings can then be adjusted or other

navigation buttons can be used to return to previous screens

or the Home Screen (FIG. 1-1).

Note: The SAVE button MUST BE pressed to ensure proper

programming of the control. Failure to press the SAVE

button will require all changes to be reprogrammed.

Figure 1-5 Initial Setup Screen

Figure 1-4 Setup Screen

1 Service

Service Manual

Table 1A Sequence of Operation

Sequence of operation

Upon a call for heat, the control turns on the appropriate pumps (system and boiler pumps for a space heating call,

HW pump for a domestic hot water call).

The control confirms that the low water cutoff contacts are closed and energizes the louvers (optional) and damper

(optional) relays.

The control confirms that the gas pressure switch, blocked drain switch, limits, louver proving switch (optional) and

damper proving switch (optional) contacts close. The Pre-Purge cycle begins.

The control confirms both blowers come up to the desired speed, both blower proving switches close, and the air

pressure switch is closed.

Once the Pre-Purge cycle is complete, the control lowers the blower speeds, initiates sparking of the ignition electrode,

and opens Gas Valve 1.

After a short wait, the control stops sparking and checks for the presence of flame current through the flame sense

electrode.

If the control does not detect flame current, the control will lockout indefinitely, until the RESET button on the touch

screen LCD is pressed. Models FB 1500 - 2500 will have one retry.

If the control detects flame current, the control will hold the blower speed constant for a few seconds to allow the

flame to stabilize, then begin modulating the firing rate in order to maintain the controlling sensor to the desired set

point temperature.

If the current call for heat is for space heating and a HW call for heat becomes active, the control will turn on the HW

pump relay output, then turn off the boiler pump. It will then modulate the blower speed in order to maintain the

outlet temperature to the desired HW outlet set point temperature.

10.

If the first combustion system in the boiler is unable to maintain the desired set point temperature, the second

combustion system in the boiler will be started. Both blowers will modulate to a set speed, and the second gas valve

will be energized. The second combustion system will light from the first combustion system. The second flame will

be monitored much like the first. Once both combustion systems are firing, the control will work in synchronization

to maintain the desired set point temperature. If the heat load should decrease sufficiently, the second combustion

system will be shut down.

11.

Once both the space heating and HW calls for heat are satisfied, the control will turn off the gas valve(s) and begin

the Post-Purge cycle. Any pumps that are running will begin their respective Pump Delay cycles.

12.

At the end of the Post-Purge cycle, the louver relay contacts will de-energize.

13.

The control verifies that the blowers stop running and the blower proving switches open.

14.

At the end of the Pump Delay cycle(s), the pump(s) will be turned off.

Note: This unit is equipped with two (2) gas train systems. Gas Train 1 will fire first. If the demand cannot be met by the first

gas train, the second gas train (Gas Train 2) will fire.

1 Service

Service Manual

1 Service (continued)

Parameter table

Table 1B This table lists SMART TOUCH control module parameters and where to access them

Sub

Item

Parameter Name

(as shown on the LCD screen)

See

Page

Min

Max

Default

User Installer

Value Value Value Access Access

1 Clock 18 N/A N/A N/A Yes Yes

2 Date 18 N/A N/A N/A Yes Yes

3 SH Setpoint 18 32 185 120 Yes Yes

4 HWG Tank Setpoint 18 32 185 120 Yes Yes

5 MRHL Setpoint 18 32 205 205 Yes Yes

6 ARHL Setpoint 18 32 200 200 Yes Yes

7 SH Setpoint at Low Outdoor Temp. 19 32 185 180 Yes Yes

8 SH Setpoint at High Outdoor Temp. 19 32 185 68 Yes Yes

9 Low Outdoor Temperature 19 -22 86 23 Yes Yes

10 High Outdoor Temperature 19 -22 86 86 Yes Yes

11 Boiler Pump Mode 24 N/A N/A N/A No Yes

12 System Pump Mode 24 N/A N/A N/A No Yes

1 SH Min User Setpoint 18 32 185 32 No Yes

2 SH Max User Setpoint 18 32 185 185 No Yes

3 SH Setpoint 18 32 185 125 Yes Yes

4 SH Offset 18 0 36 9.9 No Yes

5 SH Differential 18 0 72 19.8 No Yes

6 HWG Tank Setpoint 18 32 185 120 Yes Yes

7 HWG Tank Differential 18 0 10 6.3 No Yes

8 MRHL Setting 18 32 205 204.8 Yes Yes

9 ARHL Setting 18 32 200 199.4 Yes Yes

10 HWG Minimum User Setpoint 19 32 185 60 No Yes

11 HWG Maximum User Setpoint 19 32 185 185 No Yes

12 HWG Boiler Setpoint 19 32 185 180 No Yes

13 HWG Boiler Offset 19 0 36 9.9 No Yes

14 HWG Boiler Differential 19 0 72 185 No Yes

1 SH Setpoint at Low Outdoor Temp. 19 32 185 180 Yes Yes

2 SH Setpoint at High Outdoor Temp 19 32 185 68 Yes Yes

3 Low Outdoor Temperature 19 -22 86 23 Yes Yes

4 High Outdoor Temperature 19 -22 86 86 Yes Yes

5 Outdoor Air Shutdown 19 32 122 79.7 No Yes

6 OA Shutdown Differential 20 32 122 79.7 No Yes

INITIAL SETUP

SETPOINTSOUTDOOR RESET

1 Service

Service Manual

Parameter table

Table 1B (continued from previous page) This table lists SMART TOUCH control module parameters and where to

access them

Sub

Item

Parameter Name

(as shown on the LCD screen)

See

Page

Min

Max

Default

User Installer

Value Value Value Access Access

7 Boost Time 20 0 250 20 No Yes

8 Boost Temperature 20 0 25 0 No Yes

9 Shift OA Reset Curve 20 -27 27 0 No Yes

1 Ramp Delay Mode 20 N/A N/A N/A No Yes

2 Ramp Delay Time #1 20 1 40 2 No Yes

3 Ramp Delay Time #2 20 1 40 2 No Yes

4 Ramp Delay Time #3 20 1 40 2 No Yes

5 Ramp Delay Time #4 20 1 40 1 No Yes

6 Ramp Delay Time #5 20 1 40 1 No Yes

7 Ramp Delay Time #6 20 1 40 1 No Yes

8 Ramp Delay Limit #1 20 10 100 20 No Yes

9 Ramp Delay Limit #2 20 10 100 30 No Yes

10 Ramp Delay Limit #3 20 10 100 40 No Yes

11 Ramp Delay Limit #4 20 10 100 55 No Yes

12 Ramp Delay Limit #5 20 10 100 75 No Yes

13 Ramp Delay Limit #6 20 10 100 100 No Yes

1 BMS Active/Inactive 21 ACTIVE INACTIVE INACTIVE No Yes

2 BMS Mode 21 POWER SETPOINT POWER No Yes

3 BMS Volts at Min Rate 21 0 10 2 No Yes

4 BMS Volts at Max Rate 21 0 10 10 No Yes

5 BMS Rate at Min Volts 21 4 100 4 No Yes

6 BMS Rate at Max Volts 21 0 100 100 No Yes

7 BMS Volts at Min Setpoint 21 0 10 2 No Yes

8 BMS Volts at Max Setpoint 21 0 10 10 No Yes

9 BMS Setpoint at Min Volts 21 32 185 68.9 No Yes

10 BMS Setpoint at Max Volts 21 32 185 178.7 No Yes

11 BMS Volts to Enable 21 0 10 2 No Yes

12 Differential to Stop BMS Demand 21 0 10 0.5 No Yes

13 BMS Enable Mode 21 ENABLE VOLTAGE VOLTAGE No Yes

OUTDOOR

RESET

RAMP DELAY

BMS

1 Service (continued)

Service Manual

Parameter table

Table 1B (continued from previous page) This table lists SMART TOUCH control module parameters and where to

access them

Sub

Item

Parameter Name

(as shown on the LCD screen)

See

Page

Min

Max

Default

User Installer

Value Value Value Access Access

1 Temperature Units 21 °F °C °F Yes Yes

2 LCD Backlight Time 21 0 255 240 Yes Yes

3 Freeze Protection; Pump On 21 -22 45 44.6 No Yes

4 Freeze Protection; Burner On 22 -22 45 37.4 No Yes

5 Freeze Protection; Burner Diff 22 0 20 5 No Yes

6 HWG to SH Switching Time 22 0 240 30 No Yes

7 SH to HWG Switching Time 22 0 240 30 No Yes

8 Anti-Cycling Time 22 0 40 10 No Yes

9 Anti-Cycling Differential 22 0 40 1 No Yes

10 HWG Rate Limiting 22 10 100 100 No Yes

11 Service Mode Timeout 22 0 40 40 No Yes

12 Controlling Sensor 22 0 4 2 No Yes

13 Inlet Control Time Delay 22 0 40 3 No Yes

1 SH Night Setback Offset Temp 22 0 90 0 No Yes

2 SH Night Setback Mon End 22 N/A N/A N/A No Yes

3 SH Night Setback Mon Begin 22 N/A N/A N/A No Yes

4 SH Night Setback Tue End 22 N/A N/A N/A No Yes

5 SH Night Setback Tue Begin 22 N/A N/A N/A No Yes

6 SH Night Setback Wed End 22 N/A N/A N/A No Yes

7 SH Night Setback Wed Begin 22 N/A N/A N/A No Yes

8 SH Night Setback Thur End 22 N/A N/A N/A No Yes

9 SH Night Setback Thur Begin 22 N/A N/A N/A No Yes

10 SH Night Setback Fri End 22 N/A N/A N/A No Yes

11 SH Night Setback Fri Begiin 22 N/A N/A N/A No Yes

12 SH Night Setback Sat End 22 N/A N/A N/A No Yes

13 SH Night Setback Sat Begin 22 N/A N/A N/A No Yes

14 SH Night Setback Sun End 22 N/A N/A N/A No Yes

15 SH Night Setback Sun Begin 22 N/A N/A N/A No Yes

ADVANCED SETUP

SH NIGHT SETBACK

1 Service

Service Manual

Parameter table

Table 1B (continued from previous page) This table lists SMART TOUCH control module parameters and where to

access them

Sub

Item

Parameter Name

(as shown on the LCD screen)

See

Page

Min

Max

Default

User Installer

Value Value Value Access Access

1 HWG Night Setback Offset Temp 22 0 90 0 No Yes

2 HWG Night Setback Mon End 22 N/A N/A N/A No Yes

3 HWG Night Setback Mon Begin 22 N/A N/A N/A No Yes

4 HWG Night Setback Tue End 22 N/A N/A N/A No Yes

5 HWG Night Setback Tue Begin 22 N/A N/A N/A No Yes

6 HWG Night Setback Wed End 22 N/A N/A N/A No Yes

7 HWG Night Setback Wed Begin 22 N/A N/A N/A No Yes

8 HWG Night Setback Thur End 22 N/A N/A N/A No Yes

9 HWG Night Setback Thur Begin 22 N/A N/A N/A No Yes

10 HWG Night Setback Fri End 22 N/A N/A N/A No Yes

11 HWG Night Setback Fri Begin 22 N/A N/A N/A No Yes

12 HWG Night Setback Sat End 22 N/A N/A N/A No Yes

13 HWG Night Setback Sat Begin 22 N/A N/A N/A No Yes

14 HWG Night Setback Sun End 22 N/A N/A N/A No Yes

15 HWG Night Setback Sun Begin 22 N/A N/A N/A No Yes

1 ModBus Active / Inactive 23 ACTIVE INACTIVE INACTIVE No Yes

2 ModBus Out of Order Timer 23 5 120 30 No Yes

1 Cascade Active / Inactive 23 ACTIVE INACTIVE INACTIVE No Yes

2 Cascade Address 23 0 7 1 No Yes

3 Cascade Offset 23 0 40 10 No Yes

4 Cascade Differential 23 0 72 20 No Yes

5 Max Boiler Setpoint for Cascade 23 32 185 185 No Yes

6 Cascade Type 23 N/A N/A N/A No Yes

7 Block Time Switching Boiler On / Off 23 0 255 60 No Yes

8 Minimum Next On Time 24 0 255 60 No Yes

9 Rate % to Switch On Next Boiler 24 1 100 80 No Yes

10 Rate % to Switch Off Last Boiler 24 1 100 10 No Yes

11 Number of Boiler Pumps Always On 24 0 8 0 No Yes

HWG NIGHT SETBACK

CASCADE

MOD

BUS

1 Service (continued)

Service Manual

Parameter table

Table 1B (continued from previous page) This table lists SMART TOUCH control module parameters and where to

access them

Sub

Item

Parameter Name

(as shown on the LCD screen)

See

Page

Min

Max

Default

User Installer

Value Value Value Access Access

1 Boiler Pump Delay 24 0.5 2400 30 No Yes

2 Boiler Pump Anti-Seize Time 24 0 40 0.33 No Yes

3 Boiler Pump Mode 24 N/A N/A N/A No Yes

4 System Pump Mode 24 N/A N/A N/A No Yes

5 System Pump Delay 24 0.5 2400 30 No Yes

6 System Pump Anti-Seize Time 24 0 40 0.33 No Yes

7 HWG Pump Delay 24 0.5 2400 30 No Yes

8 HWG Pump Anti-Seize Time 24 0 40 0.33 No Yes

9 Delta T Setpoint 24 0 60 0 No Yes

1 Maintenance Notice - Months 25 0 36 12 No Yes

2 Maintenance Notice - Running Hours 25 0 100,000 10,000 No Yes

3 Maintenance Notice - Cycles 25 0 100,000 10,000 No Yes

4 Service Contact Number 25 N/A N/A N/A No Yes

5 Service Contact Name 25 N/A N/A N/A No Yes

PUMPS

SERVICE

NOTIFICATION

1 Service

Service Manual

Viewable and changeable control parameters

A: Initial Setup

Clock and Date

The control uses an internal clock for the night setback

feature and for logging of events. For these features to

work correctly, the clock must be set when the boiler is first

installed or anytime the boiler has been powered off for more

than four (4) hours. This parameter must be accessed to set

the clock. Parameter A2 sets the date.

Parameters A3 - A12 shown in the Initial Setup Menu are

grouped here for convenience. For a detailed explanation

of each parameter, reference the specific menu for each

parameter.

B: Set Points

Space Heating (SH) Minimum Set Point

The SH minimum set point sets the minimum water

temperature set point that can be used for space heating

operation. The user or installer will not be able to program

the control with a lower SH set point. This parameter can

only be changed by the installer by accessing parameter B1.

Space Heating (SH) Maximum Set Point

The SH maximum set point sets the maximum water

temperature set point that can be used for space heating. The

user or installer will not be able to program the control with

a higher SH set point. This parameter can only be changed

by the installer by accessing parameter B2.

Space Heating (SH) Set Point

The SH set point sets the water temperature set point used

during space heating calls. This parameter can be changed by

the installer by accessing parameter B3.

SH Offset

The SH offset sets how many degrees above set point the

temperature can go before the boiler will shut off. This

parameter can only be changed by the installer by accessing

parameter B4.

SH Differential

The SH differential sets how many degrees below the offset the

temperature has to drop before the boiler turns back on. This

parameter can only be changed by the installer by accessing

parameter B5.

HWG Tank Set Point

By installing a tank sensor, the SMART TOUCH control can

perform the tank thermostat function. The SMART TOUCH

control automatically detects the presence of this sensor, and

generates a call for heat when the tank temperature drops below

the tank set point minus the differential (parameter B7), and

finishes the call for heat when the tank temperature reaches

tank set point. This parameter can be changed by the installer

by accessing parameter B6.

HWG Tank Differential

When a tank sensor is installed, the tank temperature must drop

this amount below the tank set point (parameter B6) before

the boiler will turn on. The installer can adjust this setting by

accessing the parameter B7.

Manual Reset High Limit

The SMART TOUCH control contains an integral Manual

Reset High Limit (MRHL) on the outlet of the heat exchanger.

Once the outlet temperature exceeds the MRHL set point, the

boiler will shut down and lock out. Once the outlet temperature

has dropped below this set point, the RESET button on the LCD

display must be pressed to clear this lockout. This set point can

be adjusted by accessing parameter B8.

Auto Reset High Limit

The SMART TOUCH control contains an integral Auto Reset

High Limit (ARHL) on the outlet of the heat exchanger. Once

the outlet temperature exceeds the ARHL set point, the boiler

will shut down and lock out. Once the outlet temperature has

dropped below this set point, the RESET button on the LCD

display can be pressed to reset this lockout. If RESET is not

pressed, the control will automatically reset the lockout after

five (5) minutes. This set point can be adjusted by accessing

parameter B9.

CAUTION

Before changing parameters, note the

settings so that the unit can be returned to

its original operating parameters.

NOTICE

The internal clock does not adjust for

Daylight Savings Time and therefore,

will require a manual adjustment.

NOTICE

See Table 1B on pages 13 - 17 of this manual for parameter references listed in this section. The parameter

references listed in this section will not appear on the LCD screen.

1 Service (continued)

Service Manual

HWG Minimum User Set Point

This setting controls the minimum user set point for the

tank temperature. The installer can adjust this by accessing

parameter B10.

HWG Maximum User Set Point

This setting controls the maximum user set point for the

tank temperature. The installer can adjust this by accessing

parameter B11.

HWG Boiler Set Point

When a HWG call for heat becomes active, the control will

use the HWG boiler set point to determine the firing rate of

the boiler based on the boiler outlet water temperature.

This parameter can be changed by the installer by accessing

parameter B12.

HWG Boiler Offset

This parameter reflects the degrees above HWG boiler set

point the outlet temperature can go before the boiler will

shut off. This parameter can be changed by the installer by

accessing parameter B13.

HWG Boiler Differential

This parameter reflects the degrees below HWG boiler offset

the outlet temperature has to go before the boiler turns on.

This parameter can be changed by the installer by accessing

parameter B14.

C: Outdoor Reset

SH Set Point at Low Outdoor Temperature

When the outdoor air temperature drops to or below the

Low Outdoor Temperature setting (parameter C3), the water

temperature will be at this setting (see FIG. 1-6). However, if

the user set point is set lower, the water temperature will be

limited by the user set point instead. This parameter can be

changed by accessing parameter C1.

SH Set Point at High Outdoor Temperature

When the outdoor air temperature rises to or above the

High Outdoor Temperature setting (parameter C4), the water

temperature will be at this setting (see FIG. 1-6). This

parameter can be changed by accessing parameter C2.

Low Outdoor Temperature

When the outdoor air temperature drops to its minimum

(C3), the water temperature will be at parameter C1 (FIG.

1-6). As the outdoor temperature continues to drop, the water

temperature set point will continue to rise. However, if the

user set point is set lower, the water temperature will be limited

by the user set point instead. This parameter can be changed by

accessing parameter C3.

High Outdoor Temperature

When the outdoor air temperature rises to or above this set

point, the water temperature will be at parameter C2 (FIG.

1-6). This parameter can be changed by the installer by

accessing parameter C4.

Outdoor Air Shutdown

When the outdoor temperature rises above this point, the

control will block all SH demands (HWG demands will still

be active). This parameter can be changed by the installer by

accessing parameter C5.

SET POINT AT

LOW OUTDOOR

TEMPERATURE

(SH)

SET POINT

SET POINT AT

HIGH OUTDOOR

TEMPERATURE

LOW OUTDOOR

TEMPERATURE

HIGH OUTDOOR

TEMPERATURE

Figure 1-6 Outdoor Air Reset Curve

1 Service

Service Manual

Outdoor Air Shutdown Differential

The outdoor air shutdown differential parameter is the

number of degrees below parameter C5 the outdoor air

temperature must go before the boiler will respond to a SH

demand. This parameter can be changed by the installer by

accessing parameter C6.

Boost Time

The boost time parameter sets the amount of time that must

elapse with a SH demand before the water temperature

calculated set point will be increased. This parameter can

be changed by the installer by accessing parameter C7.

Boost Temperature

If a SH demand lasts longer than the programmed boost

time delay setting (C7) and there have been no HWG

demands, the control will increase the water temperature

set point by the amount in this parameter. If the SH

demand continues through another time period, the set

point will be increased again. This will continue until

either the SH demand ends, a maximum of 20 increases

has occurred, or the maximum set point has been reached.

Once the SH demand has been satisfied the set point will

revert back to its calculated setting. The boost temperature

can be changed by the installer by accessing parameter C8.

Shift OA Reset Curve

The shift reset curve parameter shifts the actual set point above

or below the calculated set point by the number of degrees in

this parameter. This parameter can be changed by the installer

by accessing parameter C9.

D: Ramp Delay

Ramp Delay (Enable / Disable)

This parameter allows the installer to enable or disable the SH

ramp delay by accessing parameter D1.

SH Ramp Delay

The SMART TOUCH control can be programmed to limit

the firing rate for a fixed period of time at the start of a space

heating demand. There are six (6) possible limits, each with

their own time delay. The first limit applies as soon as the

burner starts. Once its time delay expires, the second limit is

applied and its timer begins. The control steps through these

limits until the 6th (sixth) limit expires. Note, however, that

the 6th limit will also limit the rate for the rest of that heat

demand. The installer can adjust the firing limits and time

delays by accessing parameters D2 through D13.

Figure 1-7 Ramp Delay Interval

Page is loading ...

Lochinvar 1.5 User manual

Brand: Lochinvar

Model: 1.5

Category: Navigators

Type: User manual

Download PDF

report

Lochinvar 1.5 User manual

Lochinvar 1.5 User manual

Related papers

Other documents