Miller LF000000 Owner's manual

Miller
Brand
Miller
Model
LF000000
Type
Owner's manual

This manual is also suitable for

Miller LF000000 is a versatile and powerful tool that can greatly enhance your welding capabilities. With its advanced features and user-friendly design, it is suitable for both professional welders and hobbyists alike. Here are some of the key features and possible use cases of the Miller LF000000:

Multi-process welding: The Miller LF000000 is a multi-process welder, meaning it can weld using various welding processes such as MIG, TIG, and stick welding. This versatility makes it ideal for welding different types of metals and thicknesses, allowing you to tackle a wide range of welding projects.

Miller LF000000 is a versatile and powerful tool that can greatly enhance your welding capabilities. With its advanced features and user-friendly design, it is suitable for both professional welders and hobbyists alike. Here are some of the key features and possible use cases of the Miller LF000000:

Multi-process welding: The Miller LF000000 is a multi-process welder, meaning it can weld using various welding processes such as MIG, TIG, and stick welding. This versatility makes it ideal for welding different types of metals and thicknesses, allowing you to tackle a wide range of welding projects.

OWNER’S MANUAL
January 2005 OM-208 386A
Running Gear For Snap-On Plasma Cutter (903 891-01-2)
WARNING
ELECTRIC SHOCK can kill.
• Do not touch live electrical parts.
• Turn Off power source and input disconnect device.
• Disconnect input plug or power conductors from
deenergized supply BEFORE moving power
source.
FALLING EQUIPMENT can cause injury
and damage.
• Properly install and secure power source into holes
provided on cart.
• Always secure or remove any tools stored on cart
before moving unit.
• Cart is only designed to handle weight of power
source, cables, torch, and a few simple tools − do not
overload cart with any additional weight.
Ref. 802 469-C
Tools Needed:
Description (Qty)
Part
No.
Item
No.
1 208 744 Bracket RH (1)
2 601 944 Screw, 312-18 x .50 (4)
3 208 745 Pan, Bottom (1)
4 208 743 Bracket LH (1)
5 195 622 Label, Warning (2)
6 172 684 Nut, 312-18 (2)
7 208 746 Bracket, mtg casters (1)
8 109 318 Caster, 2-1/2 in (2)
9 081 960 Retaining Ring (2)
10 196 112 Wheel, 8 in (2)
11 602 250 Washer, .812 ID flat (4)
12 196 107 Axle (1)
13 172 684 Nut, 312-18 (4)
Be sure to provide Model when ordering
replacement parts.
. Both rear bolts must be
installed in bottom pan before
installing axle to running gear.
1
2
3
4
5
6
7
8
9
10
11
12
13
Remove paint from
axle grooves (12)
before installing re-
taining rings (9).
1/2 in
1/2 in
. Be sure that recessed
opening on hub is to
the outside on axle to
allow installation of
retaining ring.
14 Hole (2)
Remove side panel screws from left and
right side of power source that align with
holes in brackets.
15 Slot (2)
Loosen side panel screws on left and right
side of power source that align with slots in
brackets.
16 Pad (4)
Place power source on running gear pads
and lower loosened side panel screws into
slots in brackets.
Reinstall screws through holes in brackets
and back into side panels. Tighten side
panel screws to secure power source to
running gear.
14
15
16
Figure 1. Running Gear Assembly
OM-208 386 Page 2
Ref. 802 469-C
19
18
19
17
22
23
24
. Cord wrap can be installed to
either left or right side of
running gear.
17 208 747 Support Bracket (1)
18 208 750 Cord Wrap (1)
19 602 154 Screw
250-20 x .50 in (6)
20 142 735 Screw
010-24 x .50 hexwhd (4)
21 131 749 Nut
010-24 .37 hex (4)
Install support bracket to running
gear and hold in place using screws
in side without cord wrap. Do not
tighten hardware.
Install cord wrap and hold in place
using supplied screws. Upper
screws must also hold support
bracket. Tighten all hardware.
22 Hole (2)
Remove side panel screws from left
and right side of power source that
align with holes in brackets.
23 Slot (2)
Loosen side panel screws on left
and right side of power source that
align with slots in brackets.
24 Pad (4)
Place power source on running
gear pads and lower loosened side
panel screws into slots in brackets.
Reinstall screws through holes in
brackets and back into side panels.
Tighten side panel screws to
secure power source to running
gear.
Optional Small Unit Bracket
Installation:
If installing a smaller unit on the run-
ning gear, proceed as follows:
25 208 748 Adapter Bracket
LH (1)
26 208 749 Adapter Bracket
RH (1)
Install adapter brackets (22 and 23)
to unit using left and right side
wrapper screws that align with
bracket inner mounting flanges.
Install screw (17) and nut (18) into
left and right rear holes of outer
flange on mounting brackets. Do
not tighten hardware.
Install unit with brackets onto cart
so that loose hardware in rear
bracket holes slides down into cart
slots (20). Install screw (17) and nut
(18) into left and right front holes of
outer flange on mounting brackets.
Tighten both front and rear
hardware in mounting brackets to
secure unit to cart.
24
26
25
21
20
Optional Small Unit
Bracket Installation
Figure 2. Installing Cord Wrap
  • Page 1 1
  • Page 2 2

Miller LF000000 Owner's manual

Miller
Brand
Miller
Model
LF000000
Type
Owner's manual
This manual is also suitable for

Miller LF000000 is a versatile and powerful tool that can greatly enhance your welding capabilities. With its advanced features and user-friendly design, it is suitable for both professional welders and hobbyists alike. Here are some of the key features and possible use cases of the Miller LF000000:

Multi-process welding: The Miller LF000000 is a multi-process welder, meaning it can weld using various welding processes such as MIG, TIG, and stick welding. This versatility makes it ideal for welding different types of metals and thicknesses, allowing you to tackle a wide range of welding projects.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents