Miller GYRO BAIL-15/25 (041979) Owner's manual

Miller
Brand
Miller
Model
GYRO BAIL-15/25 (041979)
Category
Car kits
Type
Owner's manual

This manual is also suitable for

OWNER’S MANUAL
OM-714 147 531C
2010−04
Gyro Bail-15/25 (041 979)
1. Safety Symbol Definitions
DANGER! − Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained
in the text.
Beware of electric shock from wiring. Disconnect input
power before installing this kit.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible ha-
zards are shown in the adjoining symbols or explained in
the text.
Wear safety glasses with side shields.
NOTICE
Indicates statements not related to personal injury.
Indicates special instructions.
Have only trained and qualified persons install, operate,
or service this unit. Call your distributor if you do not un-
derstand the directions. For WELDING SAFETY and
EMF information, read owner’s manual(s).
Proposition 65 Warnings
Welding or cutting equipment produces fumes or gases which contain
chemicals known to the State of California to cause birth defects and,
in some cases, cancer. (California Health & Safety Code Section
25249.5 et seq.)
This product contains chemicals, including lead, known to the state of
California to cause cancer, birth defects, or other reproductive harm.
Wash hands after use.
OM-682 Page 2
147 722-B / 800 191
Part
No.
Item
No.
Description (Qty)
1 601 926 Screw, 1/4-20 x 5/8 (4)
2 602 207 Washer, 1/4 lock (4)
3 147 530 Mounting Bracket LH (1)
4 147 529 Mounting Bracket RH (1)
5 147 527 Suspension Yoke (1)
6 110 510 Eye Bolt (1)
7 602 213 Washer, 3/8 split lock (5)
8 010 909 Nut, 3/8-16 (3)
9 601 871 Nut, 3/8-16 jam (7)
10 602 243 Washer, 3/8 flat (8)
11 142 156 Screw, 3/8-16 x 1-3/4 (2)
12 147 528 Gyro Bail Bracket (2)
13 601 965 Screw, 3/8-16 x 1 (5)
14 110 509 Ring (1)
15 024 665 Bearing (3)
16 602 221 Washer, 3/8 tooth lock (3)
Be sure bearing (15) is tightened securly to
bracket (4), so that ring (14) is seated as
deeply as possible onto bearing (15).
. Adjust the pivot point or tilt angle of the
spot welder by loosening the two self-lock-
ing nuts (8) and sliding the spot welder
along the gyro bail brackets (12).
NOTICE − Check periodically to make sure all
hardware is secure.
Be sure to provide Model when ordering re-
placement parts.
Tools Needed:
3/8, 9/16, 5/8 in.
5
1
2
3
4
6
8
11
10
9
2
1
7
8
7
10
13
14
15
16
7
9
13
9
12
Figure 1. Gyro Bail-15/25 Assembly
  • Page 1 1
  • Page 2 2

Miller GYRO BAIL-15/25 (041979) Owner's manual

Miller
Brand
Miller
Model
GYRO BAIL-15/25 (041979)
Category
Car kits
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents