OWNER’S MANUAL
© 2010 MILLER Electric Mfg. Co.
FORM: OM-6615 217 740E
2010−04
Running Gear/Cylinder Rack (217 735)
1. Safety Symbol Definitions
DANGER! − Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained
in the text.
Cylinders contain gas under high pressure and can ex-
plode if damaged. Never let a welding electrode touch
any cylinder. Always secure cylinder to running gear, wall,
or other stationary support.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible ha-
zards are shown in the adjoining symbols or explained in
the text.
Falling equipment can injure, and damage equipment.
Never put any body part under unit while lifting. Lifting
forks must extend out opposite side of base. Lift and sup-
port unit only with proper equipment and correct proced-
ures. Follow the guidelines in the Applications Manual for
the Revised NIOSH Lifting Equation (Publication No.
94−110) when manually lifting heavy parts or equipment.
NOTICE
Indicates statements not related to personal injury.
Indicates special instructions.
Wear safety glasses with side shields.
Beware of electric shock from wiring. Do not touch live
electrical parts. Disconnect input power. Disconnect input
plug or power conductors from deenergized supply
BEFORE moving welding power source.
Proposition 65 Warnings
Welding or cutting equipment produces fumes or gases which
contain chemicals known to the State of California to cause birth
defects and, in some cases, cancer. (California Health & Safety
Code Section 25249.5 et seq.)
This product contains chemicals, including lead, known to the
state of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after use.
2. Tools Needed
14 mm
OM-6615 Page 2
3. Running Gear/Cylinder Rack Assembly
803 666-C
Assembly order:
1 Assemble bottom tray, casters, axle
and wheels to frame supports.
2 Install bottle bracket by hooking it
through bottom tray slot.
3 Install top tray to frame supports and
bottle bracket.
Description (Qty)
Part
No.
Item
No.
1 200 089 Bottom Tray (1). . . . . . .
2 218 509 Support Frame (2). . . . . . .
3 199 961 Caster (2). . . . . . .
4 217 736 Bottle Bracket (1). . . . . . .
5 218 094 Top Tray (1). . . . . . .
6 208 983 Axle (1). . . . . . .
7 208 985 Wheel, 6 in (2). . . . . . .
8 200 120 Chain, 24 in (1). . . . . . .
9 200 121 Tubing Plug (4). . . . . . .
10 235 618 Warning Label (1). . . . . . .
200 122 Hardware Kit. . . . . .
(consisting of). . . . . . . . . . . . .
11 Nut, M-8 (2). . . . . . . . . . . . . .
12 Lockwasher, M-8 (2). . . . . . . . . . . . . .
13 Flat Washer, M-8 (2). . . . . . . . . . . . . .
14 Cotter Pin (2). . . . . . . . . . . . . .
15 Spacer (2). . . . . . . . . . . . . .
16 Flat Washer, M-12 (4). . . . . . . . . . . . . .
17 Screw,. . . . . . . . . . . . . .
10-16x5/8 in (8). . . . . . . . . . . . . .
18 Nut, M-5 (2). . . . . . . . . . . . . .
19 Screw, M-5x12 (2). . . . . . . . . . . . . .
Be sure to provide Model when ordering
replacement parts.
1
6
17
9
7
14
8
4
19
2
3
13
5
3
2
17
18
17
9
17
10
9
15
16
11
12
12
11
13
-
1
-
2
Miller RUNNING GEAR/CYLINDER RACK (217 735) Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Miller MC050242L Owner's manual
-
-
Miller LH000000 Owner's manual
-
Miller Syncrowave 250 DX Owner's manual
-
-
-
-
-
Miller MA500345U Owner's manual
-
