Ilve T29BR Operating instructions

Brand: Ilve

Model: T29BR

Type: Operating instructions

T29B/80

T29BR/80

T29B/100

T29BR/100

T29B/120

T29BR/120

230Vac - 50Hz

Exhausting cooker hood. The equipment is constructed in

accordance with European Standards and with the requirements

included in the following Directives: 2006/95EC ( Low Voltage

Directive), 2004/108 (Electromagnetic Compatibility).

1 INSTALLATION

Read the instruction manual before installing and/or using the

hood .

In order that the minimum distance between the supporting

surface for the cooking pots on gas hob and low-voltage

components present in the hood is at least 65cm as required by

the regulations in force, it is necessary that the lower part of the

hood is at least 65-70cm away from the work top.

If the mounting instructions of the gas cooker indicate a wider

distance, respect it. The unit must not be mounted above cookers

tted with top radiant plate.

Respect all the air discharge regulations.

The air must not be discharged in a pipe used to discharge

exhaust fumes produced by gas- fed equipments or fuel-fed

equipments (this does not apply to ltering hoods).

The room must be adequately ventilated when the hoods is used

together with other gas-fed or fuel-fed equipments.

The hood is equipped with all the necessary fastenings for its

installation, which are suitable for most surfaces. Anyway, ask

to a professional to verify that the installation surface is strong

enough. Installation must be carried out by qualied installers

according to present regulations.

For an easy access, it is advisable to move possible furniture

under the installation area.

Install in the cabinet the two metal brackets provided with the

cooker hood (Fig. 2) at a distance of 40 mm from the front edge

and not less than 37 mm from the bottom edge of the cabinet

itself. Install the hood inside the cabinet (Fig. 1) and fasten it

with four screws to the brackets, then close the holes with the

caps provided (Fig. 3).

Installation and utilizing spacer (Fig.4)

Once you have mounted the cooker hood in the wall unit it is

possible to adjust unit depth utilizing the spacer provided with

the cooker hood.

2 ELECTRICAL CONNECTIONS

This appliance must be connected to an earthed power supply.

Two types of electrical connection can be used:

1. Using a standard plug to be connected to the power cable

and inserted in a mains socket which must be accessible (so

that the plug can be disconnected when servicing is carried

out). Make sure that the plug is accessible also after the

complete installation of the equipment.

2. By means of a xed mains connection, tting a bipolar

switch, which ensures the disconnection, with an opening

distance of the contacts allowing a complete disconnection

on the conditions of the overvoltage III category, according

to installation regulations. The ground connection (yellow-

green wire) must not be interrupted.

Refer to the plate inside the hood for the mains voltage and

frequency ratings.

3 USE

This cooker hood can be employed as exhausting or ltering.

Exhausting (Fig. 4). The carbon lters should not be installed on

the hood in exhausting version.

Kitchen smokes are driven outside through a ue joined to the

exhaust pipe ue connector.

Pipes must be communicating with the exterior of the house. The

diameter of the outlet of the hood is 150mm. A 150-125 reduction

is provided with the hood.

This pipe must not under any circumstances be connected to

cooker, boiler or burner exhaust pipes, etc.

Filtering (Fig. 5). The fumes pass through the carbon lters to be

puried and recycled into the kitchen through a pipe connected

to the outlet of the hood up to the hole in the top of the cabinet.

This hole must be free and communicating with the kitchen.

In the ltering version you must install the two carbon lters on

the sides of the aspirator. To install the carbon lters you must

rst remove the metal grease lters (Fig. 6) and then install

carbon lters by turning them counterclockwise (Fig. 7).

4 OPERATION

The hood is equipped with a multispeed motor.

It is recommended that low speed be selected for normal kitchen

conditions, and higher speeds only to combat a heavy build-up

odours and vapours.

ELECTRONIC CONTROLS

The controls (Fig. 7) have buttons for switching on the TL light, for

switching on the motor and selecting the T1-T2-T3-T4 operating

speed.

By pressing of the command T1 the motor starts running at

the 1st speed. The commands T2-T3-T4 switch the motor on

respectively at the 2nd, 3rd, 4th speed. In order to switch

the motor off press T1 once if set at the 1st speed, twice if set at

the 2nd, 3rd and 4th speed.

With the button T4, select the maximum speed of the extraction

fan for 5 minutes (LED blinking), after which the extraction fan

will automatically switch to the 3rd speed.

AUTO POWER OFF: To activate the auto power off, rst turn on

the hood and, then, push the “T1” button for a few seconds until

all LEDs start ashing. By pressing one of the buttons (T1, T2,

T3, T4) it is possible to program the auto power off time, which

will be different according to the button

pressed (T1= 5 minutes, T2=10 minutes, T3=15 minutes, T4=20

minutes). The set speed can be changed during the auto power

off time. When the auto power off option corresponds to the

previously set speed, the speed LED ashes; if the option is

different, the speed LED is xed.

FILTER TIMER: After the hood has worked for 30 hours, all

LEDS will switch on with a xed light for 30 seconds when the

hood is turned off indicating that the aluminium lters need to be

cleaned. The timer will reset if the T1+T4 button is pressed for a

few seconds with the exhaust fan turned off. If this button is not

pressed, the same operation will occur again once the hood is

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS FOR COOKER HOODS

FOR WALL FITTING 230 Vac - 50 Hz

0-1 2 3 4

TL T1 T2 T3 T4

FIG.7

switched off again. This operation will occur every 30 hours, until

120 functioning hours are reached. Once the hood has worked

for 120 hours and it is turned off, all the LEDs will turn on with

a ashing light for the following 30 seconds indicating the that

aluminium lters need cleaning and, if the hood is a ltering

hood, the active carbon lters need to be replaced.

Once the timer has been reset (by keeping the T1+T4 button

pressed for a few seconds with the exhaust fan turned off),

the entire process will present itself again after the next 30

exhausting hours.

5 MAINTENANCE AND REMINDERS

Always disconnect the hood from the electrical power supply

before any maintenance or cleaning operation. Particular care

must be given to the grease lters, which serve to trap grease

particles entrained in cooking vapours.

The grease lters are metal, and must be washed at least once

a month with warm water and detergent (dishwasher clean is

sufcient).

Dry throughly before retting.

ATTENTION: the grease collected in the lter can easily catch

re and it is therefore extremely important to clean the metallic

lter on a regular basis as per instructions.

Grease lters are removed as illustred (Fig. 7).

The function of the activated carbon lters is to prevent the

spread of odours present in the cooking fumes. Clean air is

returned to the kitchen. Carbon lters cannot be washed, and

must be replaced 2 or 3 times a year according to the amount

of use.

The hood features a LED light that, in addition to offer a good

lighting and a signicant energy savings, is guaranteed to last

about 10 times more than traditional lights. For replacement,

contact the Assistance Service.

Spare lters can be purchased from dealers or direct from the

manufacturer.

Removal: detach the metal covers and rotate the carbon lters

clockwise (Fig. 8) until release from of the motor.

Retment: position the new carbon lters and reverse the

procedure. The hood should be cleaned with a soft damp cloth

using neutral liquid detergents. Do not use solvents, petroleum

products or abrasives.

Never cook ambe’ dishes under the hood. Never leave the hob

unattended when frying, as oil or fat can catch re.

THE MANIFACTURER DOES NOT ACCEPT LIABILITY

FOR ANY DAMAGE OR INSJURY CAUSED IF THE

USER FAILS TO FOLLOW THE ABOVE INSTRUCTIONS

REGARDING INSTALLATION, MAINTENANCE AND

THE PROPER USE OF THE COOKER HOOD.

RTM62

INSTRUCTIONS FOR USE AND MAINTENANCE

230-240Vac - 50Hz

395447.1

2

3

The manufacturer is committed to continuous improvements. For this reason, the text and illustrations in this

manual may be changed without notice.

GENERAL WARNINGS

These operating instructions describe the appliance and its use. This booklet is an integral

part of the equipment and must therefore be kept with care and must ALWAYS accompany

it, even if it is transferred to another owner or user, or transferred to another installation.

The appliance is manufactured according to the safety standards in force.

The use of the appliance cannot be different from that for which it was built, i.e. the

suction of fumes generated by cooking food in the domestic, non-professional,

environment.

The manufacturer is not liable for damage caused to persons, animals or property,

installation errors, maintenance or improper use.

Warning! Do not attempt to extinguish a fire with water, but

immediately switch off the appliance and then cover the flame with

a cover or fire blanket.

Warning! before any cleaning or maintenance operation or in

thunderstorms, disconnect the appliance by turning the main system

switch to "off" (Fig.2.1) or unplugging it (Fig.2.2).

This appliance is not intended for use by persons (including children) with impaired mental

or motor skills, lack of experience and knowledge, unless supervision or instruction about

the use of the appliance by a person responsible for their safety.

In the case of disturbances, immediately unplug the mains and call the technical assistance

service.

Fig. 2.1

Fig. 2.2

4

Any changes that may be necessary to the electrical system to install the product must be

performed by competent persons only. Repairs carried out by unskilled persons can cause

damage. For eventual interventions, contact a Technical Assistance Center authorized to

replace the spare parts.

If the power cord or other components are damaged, the appliance must NOT be used:

disconnect the appliance from the power supply and contact the dealer or an authorized

Technical Assistance Center for repair.

INSTALLATION WARNINGS

Warning! It is recommended to identify a position sheltered from

rain, snow, wind, etc. to avoid water and moisture infiltration inside

the appliance that could damage it.

Warning! Do not connect the appliance to flue gas exhaust pipes (e.g.

boilers, fireplaces, etc.).

Before installing the appliance, make sure that all the regulations in

force concerning the discharge of the air outside the room are

respected. In case of simultaneous use of other utilities (boilers, stoves,

fireplaces, etc.) powered by gas or other fuels, provide adequate

ventilation of the room where the fumes are sucked in, according to

current regulations.

III

INSTALLATION

Read the entire instruction manual before installing and using the equipment.

The device is equipped with all the fixings necessary for its installation and suitable for

most situations.

The product can be installed in different configurations for wall and island hoods Fig. 01,

02, 03 at a distance not exceeding 7 meters, which corresponds to the length of the

connection cable.

Use pipes with a diameter of no less than 150mm and a number of curves not beyond the

indispensable.

The horizontal sections of the pipeline must have a slight inclination to prevent

condensation from reflow in the engine and the electrical parts.

5

Fig. 01

6

Fig. 03

Fig. 02

7

NB: If installed on the wall, the lateral exit is forbidden as shown in Fig. 04

Fig. 04

8

The connecting ring can be repositioned with the possibility of having the air inlet ortho

to the exit or opposite the exit Fig. 05, 06, 07.

Fig. 05

9

Fig. 07

Fig. 06

10

Once you have identified the position and the most suitable surface for the device, fix as

shown in Fig. 08

Fig. 0

11

ELECTRICAL CONNECTION

The electrical connection must be performed ONLY by specialized technicians.

The electrical protection of the electrical connection upstream of the appliance must

comply with the regulations in force.

Warning! Make sure that the voltage (V) and frequency (Hz) indicated

on the serial number plate inside the fixtures correspond to those

available at the installation place.

Any changes that may be necessary to the electrical system to install the device must be

performed only by competent persons.

After installation, the isolated parts and those carrying electric current must be protected

from any contact.

Warning! If the electrical connection is performed incorrectly or not

in accordance with the regulations, parts of the appliance may be

damaged and the warranty will not be accepted.

Warning! Before each intervention, disconnect the appliance from

the mains (Fig.1-2 chapter WARNINGS).

The earth connection (yellow-green cable) must under no circumstances be

interrupted.

This appliance must be connected to a hood prepared without an aspirator for this type of

device as shown in Fig. 09 and 10.

The device will then be powered and controlled directly by the hood.

12

Fig. 09

13

MAINTENANCE AND CLEANING

Warning! Before any maintenance or cleaning operation,

disconnect the power supply from the filter and the hood (chapter

II WARNINGS).

Fig. 10

14

NOTICE OUT OF OPERATION, DISMANTLING AND DISPOSAL

PUT OUT OF EXERCISE

With the shutdown, this means the definitive putting out of service and the disassembly

of the appliance. Following the shutdown, the appliance can be incorporated into another

piece of furniture, either sold privately or disposed of.

Warning! To put the appliance out of exercise it is necessary to

switch off the appliance and disconnect the power supply from the

hood (Fig.1-2 chapter WARNINGS).

Warning! Make disconnection and closing of power lines only by

specialized personnel.

REMOVAL

Disassembly requires that the appliance is accessible for disassembly and has been

disconnected from the power supply.

To perform this operation, you must:



Loosen screws and fixing brackets



Remove any silicone sealings



Disconnect the engine from the suction channel

DISPOSAL

This device is marked in accordance with the European Directive

2012/19/EC, Waste Electrical and Electronic Equipment (WEEE).

The symbol on the product or on the packaging indicates that the product

should not be considered a normal household waste, but must be taken to

the appropriate collection point for the recycling of electrical and electronic

equipment.

By disposing of this product appropriately, you are helping to avoid potential negative

consequences for the environment and for health, which could result from improper

disposal of the product. For more detailed information on recycling this product, contact

the municipal office, the local waste disposal service or the shop where the product was

purchased.

Ilve T29BR Operating instructions

Ilve T29BR Operating instructions

Ilve T29BR Operating instructions

Related papers

Other documents