Wolf CT30ES 30 Framed Electric Cooktop Planning Guide
- Category
- Cookers
- Type
- 30 Framed Electric Cooktop Planning Guide
This manual is also suitable for
Planning Information
New 30" (762) Framed Electric Cooktop
— Available November 2007
MODEL CT30E
1
Dimensions in parentheses are in
millimeters unless otherwise specified.
8/08
Model CT30E
The Wolf Model CT30E 30" (762)
framed electric cooktop is available with
the classic, platinum or carbon stainless
steel trim finish. The optional Model
CT30E-208/S is designed specifically for
use with a 208 V AC electrical supply.
Behind the sophisticated, minimalist exterior, beneath
that perfectly smooth, subtly patterned glass that
cleverly reduces scratches, there is a high-performance
cooking tool.
The black ceramic glass top of the framed electric
cooktops is beautifully complemented by your choice
of classic, platinum or carbon stainless steel trim finish.
Wolf framed electric cooktops feature multiple cooking
elements with different zones—concentric rings that
give you exceptional control of temperature for pots
and pans of every size. Model CT30E offers a bridge
that connects two elements for an 8-inch by 17-inch,
4400 watt heating area.
All of the heating elements offer True Simmer, and with
each cooktop there is one element that enables you to
set a temperature for melting.
The new framed electric cooktops will be available in
November 2007 and will replace existing models.
This appliance is certified by Star-K
to meet strict religious regulations in
conjunction with specific instructions
found on www.star-k.org.
C
L
E
A
R
OF
F
O
S
I
M
HI
GH
O
FF
ON
O
F
F
O
N
S
I
M
HI
G
H
OF
F
O
N
S
I
M
H
I
G
H
B
R
I
D
G
E
Z
O
N
E
2
Z
O
N
E
3
H
I
G
H
M
E
L
T
O
F
F
ON
Triple-zone
element
Location of
rating plate
Stainless steel
trim finish
Bridge-zone
element
Electronic touch
controls
Lock key
Hot-surface
indicator light
Universal
OFF key
Countdown
timer
Melt setting
True Simmer on
all elements
Planning Information
New 30" (762) Framed Electric Cooktop
MODEL CT30E
2
21"
(533)
OVERALL
DEPTH
30" (762)
OVERALL WIDTH
5" (127)3
3
/4" (96)
CONDUIT
OVERALL DIMENSIONS
Dimensions in parentheses are in
millimeters unless otherwise specified.
Unit dimensions may vary by ±
1
/
8
" (3).
FEATURES
Classic, platinum and carbon stainless steel
trim finishes
Optional Model CT30E-208/S designed
specifically for use with 208 V AC electrical
supply
Easy-to-clean black ceramic glass surface is
resistant to scratching, staining, impact and
heat—translucent surface allows you to see
the glow of hot elements
High-frequency pulsation elements improve
cooking performance and control
Three heating elements with seven zones
Triple-zone element power (maximum)—
Model CT30E: 900 W / 1800 W / 2500 W
Model CT30E-208/S: 825 W / 1750 W / 2300 W
Single element power: 1200 W (maximum)
Bridge-zone element power—(2) 1800 W
single elements with 800 W bridge: 4400 W
(maximum)
Temperature limiter to ensure that safe
operating temperature of ceramic glass is
never exceeded
Illuminated touch controls with graduated
control lighting
True Simmer setting on all elements
Melt setting on one element
Hot-surface indicator light in control panel
Lock mode—cooktop can be locked so that
no elements can be turned on
Universal OFF turns all elements off
Countdown timer with 1 to 99 minute range
and adjustable sound frequency and volume
CSA certified for US and Canada
Two and five year residential warranty—
exclusions apply; warranty information can
be found on our website, wolfappliance.com
Planning Information
New 30" (762) Framed Electric Cooktop
MODEL CT30E
Dimensions in parentheses are in
millimeters unless otherwise specified.
3
SPECIFICATIONS
Overall Cooktop Width 30" (762)
Overall Cooktop Height 3
3
/4" (96)
Overall Cooktop Depth 21" (533)
Heating Element Maximum Power (Model CT30E)
(1) Triple – 2500 W outer / 1800 W middle / 900 W inner
(3) Single – (2) 1800 W and 1200 W
Bridge Element – 4400 W (with 1800 W singles)
Heating Element Maximum Power (Model CT30E-208/S)
(1) Triple – 2300 W outer / 1750 W middle / 825 W inner
(3) Single – (2) 1800 W and 1200 W
Bridge Element – 4400 W (with 1800 W singles)
Heating Element Outer Diameter
(1) Triple – 10" (254)
(3) Single – (2) 8" (203) and 6
1
/2" (165)
Bridge Element Dimensions 8" (203) x 17" (432)
Recommended Cabinet Width 33" (838)
Minimum Cabinet Width 30" (762)
Minimum Cabinet Depth 22
3
/4" (578)
Minimum Height Clearance* 4" (102)
Cooktop Cut-Out Width 28
3
/8" (721)
Cooktop Cut-Out Depth 19
1
/4" (489)
Electrical Supply Requirements
(Model CT30E) 240 V AC / 60 Hz / 40 amp
208 V AC / 60 Hz / 40 amp
Electrical Supply Requirements
(Model CT30E-208/S) 208 V AC / 60 Hz / 40 amp
Conduit 4 ft (1.2 m) flexible 3-wire
Electric Rating (Model CT30E) 8.1 kW at 240 V
6.1 kW at 208 V
Electric Rating (Model CT30E-208/S) 7.9 kW at 208 V
Shipping Weight 45 lbs (20 kg)
*Minimum 5
3
/
4
" (146) clearance is required between countertop
and any combustible surface directly below the cooktop.
Specifications are subject to change without notice.
MODEL OPTIONS
Classic Stainless Trim CT30E/S
Platinum Stainless Trim CT30E/P
Carbon Stainless Trim CT30E/B
VENTILATION OPTIONS
30" (762) Cooktop hood or Pro
wall or wall chimney hood or liner
30" (762) or 45" (1143) downdraft
ventilation system
36" (914) Pro island hood
For additional information, refer to the
Cooktop or Pro Ventilation sections of our
website, wolfappliance.com.
ACCESSORIES
Filler strip
Accessories are available through your
Wolf dealer. To obtain local dealer
information, visit the Showroom Locator
section of our website, wolfappliance.com.
Unit dimensions may vary by ±
1
/
8
" (3).
Model CT30E
Planning Information
New 30" (762) Framed Electric Cooktop
MODEL CT30E
Dimensions in parentheses are in
millimeters unless otherwise specified.
4
INSTALLATION SPECIFICATIONS
2"*min (51)
CUT-OUT TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
18"
(457)
19
1
/4" (489)
COOKTOP CUT-OUT
DEPTH
2
1
/2"min
(64)
36" (914)
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
13" max
(330)
30" (762)
COUNTERTOP TO
COMBUSTIBLE
MATERIALS
ABOVE COOKTOP
24"min
(610)
*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 18" (457) above countertop. **Minimum clearance
from rear edge of cooktop cut-out to combustible materials up to 18" (457) above countertop.
4" (102)
10"
(254)
3
1
/2" (89)
3
3
/4"min
(95)
30-INCH OVEN OPENING
E
28
3
/8" (721) COOKTOP
CUT-OUT WIDTH
28
3
/8" (721)
COOKTOP CUT-OUT WIDTH
FRONT OF COUNTERTOP
2
1
/2"min
(64)
19
1
/4" (489)
COOKTOP
CUT-OUT DEPTH
33" (838)
RECOMMENDED
CABINET WIDTH
30"min (762)
2"**
(51)
DIMENSIONS
Recommended Cabinet Width 33" (838)
Minimum Cabinet Depth 22
3
/4" (578)
Cooktop Cut-Out Width 28
3
/8" (721)
Cooktop Cut-Out Depth 19
1
/4" (489)
Location of Electrical Within shaded area
See Installation Instructions shipped with unit for detailed specifications.
Planning Information
New 30" (762) Framed Electric Cooktop
MODEL CT30E
Dimensions in parentheses are in
millimeters unless otherwise specified.
5
INSTALLATION NOTES
Refer to the illustrations and specifications
for overall dimensions, cut-out dimensions and
installation specifics.
Optional Model CT30E-208/S is designed
specifically for use with a 208 V AC, 60 Hz, 40
amp electrical supply.
Wolf recommends using a 33" (838) wide
cabinet with the 30" (762) framed electric
cooktop.
A Wolf downdraft system, Cooktop or
Pro ventilation hood is recommended. When
installing a ventilation hood, refer to the specific
requirements of the hood for the minimum
dimension to countertop. Also refer to the
ventilation recommendation charts in the
cooktop or Pro ventilation sections of our
website, wolfappliance.com.
Model CT30E requires a separate, grounded
3-wire 240 V AC, 60 Hz, 40 amp or 208 V AC,
60 Hz, 30 amp service with its own circuit
breaker. Model CT30E-208/S requires a
separate, grounded 3-wire 208 V AC, 60 Hz, 40
amp service with its own circuit breaker. Both
models are provided with a 4' (1.2 m) flexible
3-wire conduit for connection at the electrical
supply. Locate electrical within the shaded area
shown in the illustration on page 4.
A Wolf built-in single oven may be installed
below this cooktop. For this installation, the
electrical supply for the cooktop should be
installed in the adjacent cabinet. Refer to the
illustration on page 6 for specifications. Be
aware of the depth of the cooktop when
planning for this installation.
IMPORTANT NOTE: When a built-in oven is
installed below the cooktop, unless you are
using cabinets deeper than 24" (610), it is
recommended that the electrical supply be
placed in an adjacent cabinet within reach of
the conduit.
IMPORTANT NOTE: Wolf framed electric
cooktops are designed and agency approved for
installation with Wolf built-in ovens only.
You must follow all National Electrical Code
regulations. In addition, be aware of local codes
and ordinances when installing your service.
If the 30" (762) framed electric cooktop is to
be used with any combination of additional
cooktop units or modules with a filler strip, the
cut-out width increases to 29" (737). When
multiple cooktops or modules are installed side
by side, refer to the countertop cut-out dimen-
sions on page 7.
Refer to the installation instructions
shipped with each Wolf product for detailed
specifications.
This cooktop is intended for indoor use only.
Planning Information
New 30" (762) Framed Electric Cooktop
MODEL CT30E
Dimensions in parentheses are in
millimeters unless otherwise specified.
6
INSTALLATION WITH BUILT-IN OVEN
The Wolf 30" (762) framed electric cooktop may
be installed above a 30" (762) L Series or
E Series built-in single oven. Refer to the illustra-
tion below for specifications.
IMPORTANT NOTE: When a built-in oven is
installed below the cooktop, unless you are
using cabinets deeper than 24" (610), it is
recommended that the electrical supply for the
oven and the cooktop be located in the adjacent
right side cabinet. A 2" (51) diameter hole to
route the conduit through cabinetry will be
required.
IMPORTANT NOTE: Wolf framed electric
cooktops are designed and agency approved for
installation with Wolf built-in ovens only.
Wolf recommends using a 33" (838) wide
cabinet for this installation. A minimum 24"
(610) of usable cabinet depth is required. The
cabinet base must be able to support 250 lbs
(113 kg).
The Wolf 30" (762) electric cooktop may also be
installed above a Wolf 36" (914) L Series built-in
single oven.
For additional specifications, refer to the built-in
ovens section of our website, wolfappliance.com.
2"*min (51)
CUT-OUT TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
18"
(457)
19
1
/4" (489)
COOKTOP CUT-OUT
DEPTH
2
1
/2"min
(64)
36" (914)
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
13" max
(330)
30" (762)
COUNTERTOP TO
COMBUSTIBLE
MATERIALS
ABOVE COOKTOP
*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 18" (457) above countertop. **Minimum clearance
from rear edge of cooktop cut-out to combustible materials up to 18" (457) above countertop. Unless you are using cabinets deeper than 24"
(610), the electrical supply for the oven and the electrical supply for the cooktop should be located in the adjacent right side cabinet as shown.
28
3
/8" (721) COOKTOP
CUT-OUT WIDTH
33" (838)
RECOMMENDED
CABINET WIDTH
30"min (762)
24" min
(610)
10"
(254)
3
1
/2"(89)
E
COOKTOP
ELECTRICAL
LOCATION IN
ADJACENT RIGHT
SIDE CABINET
3
3
/4" min (95)
4
3
/4" min (121)
27
3
/16"
(691)
E
E
5"
(127)
28
1
/2" (724)
OVEN OPENING WIDTH
4"
(102)
OVEN ELECTRICAL
LOCATION WITHIN
OPENING APPLIES
ONLY TO CABINETS
DEEPER THAN 24" (610)
4" (102)
2"**
(51)
Installation of a 30" (762) framed electric cooktop above a 30" (762) L Series or E Series single oven.
Planning Information
New 30" (762) Framed Electric Cooktop
MODEL CT30E
Dimensions in parentheses are in
millimeters unless otherwise specified.
7
MULTIPLE COOKTOP INSTALLATION
With Wolf's integrated modules, you have the
ultimate in customization. You can create your
own design by mixing and matching the various
components within this system. And when you
couple these modules with other cooktops
within the Wolf inventory you and your client will
truly understand freedom of choice.
Some Wolf integrated modules can be installed
together or with a 30" (762) or 36" (914)
cooktop. When multiple units are installed side
by side, the cut-out dimensions that are shown
in the illustration are derived by adding 1
1
/4" (32)
additional space for each additional unit, to give
you your total cut-out width. Refer to the illus-
tration below for countertop cut-out dimensions
for installation of multiple cooktop units.
When two or more cooktops or modules are
installed together, an accessory filler strip is
recommended. Refer to Accessories on page 3.
Countertop cut-out dimensions for installation of multiple cooktop units.
IMPORTANT NOTE: When multiple cooktops
and/or modules are installed side by side, each
unit must have its own separate recommended
electrical circuit. When multiple gas cooktops
and/or modules are installed next to one
another, they can receive their gas supply from a
common line. However, each unit must have its
own regulator installed between the mainline
and the cooktop or module.
IMPORTANT NOTE: Review specifications for
each specific integrated module for installation
requirements and limitations. Refer to the
integrated modules section of our website,
wolfappliance.com.
2
1
/2"min
(64)
FRONT OF COUNTERTOP
19
1
/4"
(489)
CUT-OUT
DEPTH
29
1
/
4
"
(743)
TWO MODULES WIDTH
44
1
/
2
"
(1130) THREE MODULES WIDTH OR
44
1
/
4
"
(1124) 30" COOKTOP AND ONE MODULE
59
3
/
4
"
(1518) FOUR MODULES WIDTH OR
59
1
/
2
"
(1511) 30" COOKTOP AND TWO MODULES OR
50
1
/
4
"
(1276) 36" COOKTOP AND ONE MODULE
14"
(356)
CUT-OUT
WIDTH
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Wolf CT30ES 30 Framed Electric Cooktop Planning Guide
- Category
- Cookers
- Type
- 30 Framed Electric Cooktop Planning Guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI