Maytag UXD8630DYS User guide

Brand: Maytag

Model: UXD8630DYS

Type: User guide

This manual is also suitable for

30" (76.2 CM) AND 36" (91.4 CM)

RETRACTABLE (POP-UP) DOWNDRAFT VENT SYSTEM

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301

or visit our website at www.whirlpool.com

In Canada, call 1-800-807-6777 or visit our website at www.whirlpool.ca

SYSTÈME DE VENTILATION RÉTRACTABLE (CLAPET) DE

30" (76,2 CM) ET 36" (91,4 CM)—ASPIRATION

PAR LE BAS

Instructions d’installation et Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service, composer

le 1-800-807-6777 ou visiter notre site Web à

www.whirlpool.ca

Table of Contents/Table des matières.............................................................................2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISATION RÉSIDENTIELLE UNIQUEMENT.

LI3ZUB/W10342491C

TABLE OF CONTENTS

VENT SYSTEM SAFETY.................................................................2

INSTALLATION REQUIREMENTS................................................4

Tools and Parts ............................................................................4

Location Requirements................................................................4

Electrical Requirements ...............................................................7

Venting Requirements..................................................................7

INSTALLATION INSTRUCTIONS..................................................8

Venting Methods..........................................................................8

Install Vent System.......................................................................9

Rear Mounting—Blower Motor..................................................11

Complete Installation .................................................................12

Make Electrical Connections .....................................................13

Check Operation ........................................................................14

VENT SYSTEM USE .....................................................................14

Operating Downdraft Vent .........................................................15

VENT SYSTEM CARE...................................................................15

Surface of Downdraft Vent.........................................................15

Filters ..........................................................................................15

WIRING DIAGRAM .......................................................................16

ASSISTANCE OR SERVICE.........................................................17

In the U.S.A. ...............................................................................17

In Canada ...................................................................................17

Accessories ................................................................................17

WARRANTY ..................................................................................18

TABLE DES MATIÈRES

SÉCURITÉ DU SYSTÈME DE VENTILATION.............................19

EXIGENCES D’INSTALLATION...................................................21

Outils et pièces...........................................................................21

Exigences d’emplacement.........................................................21

Spécifications électriques..........................................................24

Exigences concernant l'évacuation...........................................24

INSTRUCTIONS D'INSTALLATION ............................................25

Méthodes d’évacuation .............................................................25

Installation du conduit d’évacuation..........................................26

Montage du ventilateur à l'arrière ..............................................28

Achever l’installation ..................................................................29

Raccordements électriques.......................................................30

Contrôle du fonctionnement ......................................................31

UTILISATION DU SYSTÈME D'EXTRACTION...........................31

Utilisation du système d'extraction par le bas...........................32

ENTRETIEN DU SYSTÈME D’ÉVACUATION .............................32

Surface du système d'extraction par le bas..............................32

Filtres ..........................................................................................32

SCHÉMA DE CÂBLAGE...............................................................33

ASSISTANCE OU SERVICE.........................................................34

Au Canada..................................................................................34

Accessoires ................................................................................34

GARANTIE.....................................................................................35

VENT SYSTEM SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

■ Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

■ Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

■ Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction.

■ Do not operate any fan with a damaged cord or plug.

Discard fan or return to an authorized service facility for

examination and/or repair.

■ Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

■ When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

■ Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

■ Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

■ Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flambé).

■ Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

■ Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING:

■ SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

■ NEVER PICK UP A FLAMING PAN - you may be burned.

■ DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

■ Use an extinguisher ONLY if:

– You know you have a class ABC extinguisher, and you

already know how to operate it.

– The fire is small and contained in the area where it

started.

– The fire department is being called.

– You can fight the fire with your back to an exit.

Based on "Kitchen Fire Safety Tips" published by NFPA.

■ WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

■ Jigsaw or keyhole saw

■ Drill

■ ¹⁄₈" (3 mm) drill bit for pilot holes

■ Pencil

■ Tape measure or ruler

■ Flat-blade screwdriver

■ Phillips screwdriver

■ ³⁄₈" (9.5 mm) nut driver

■ Level

■ Pliers

■ Metal snips

■ Wire stripper or utility knife

■ Caulking gun and weatherproof caulking compound

Parts Supplied

■ Top trim—stainless

■ End caps (2)

■ Lower support legs (2)

■ Undercounter mounting brackets (2)

■ 4 x 8 mm screws (16)

■ 3.5 x 9.5 mm screws (3)

■ 3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular damper

■ 4³⁄₄" (12.0 cm) motor box

■ ¼" (6.4 mm) deep cover

■ Flat vent cover plate

■ 6" (15.2 cm) diameter vent transition with damper

Parts Needed

■ UL listed or CSA approved ½" (12.7 mm) conduit connector

■ Wall or roof cap with damper to match vent system

■ Vent system

■ Home power supply cable

■ UL listed wire connectors (3)

■ Vent clamps/duct tape as required

Location Requirements

NOTE: Downdraft vent is installed directly behind the cooktop.

Install the downdraft vent first, then install the cooktop.

IMPORTANT: Observe all governing codes and ordinances.

■ Have a qualified technician install the downdraft vent. It is the

installer’s responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial

rating plate is located on the front of the downdraft vent

above the terminal box cover.

■ Downdraft vent location should be away from strong draft

areas, such as windows, doors, and strong heating vents or

fans.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance.

■ Consult the cooktop manufacturer installation instructions

before making any cutouts.

Check that the downdraft vent and cooktop location will

clear the cabinet walls, backsplash, and rear wall studs

inside the cabinet.

Check for the minimum distance between the front edge

of the countertop and the front edge of the cooktop. The

minimum horizontal distance between the overhead

cabinets is the same as the width of the installed

downdraft vent.

■ All openings in ceiling and wall where the downdraft vent will

be installed must be sealed.

■ Grounded electrical outlet is required. See “Electrical

Requirements” section.

■ When installing the downdraft vent, the cabinet drawer will

need to be removed and the drawer front installed

permanently to the cabinet.

Cabinet Construction:

Downdraft vent is designed for use in a cabinet with a depth of

24" (61 cm). Some installations require a countertop deeper than

25" (63.5 cm). See the “Countertop Cutout Dimensions Chart.”

The maximum depth of the overhead cabinet is 13" (33 cm).

Overhead cabinets installed at either side of the downdraft vent

must be 18" (45.7 cm) above the cooking surface.

For Mobile Home Installations

The installation of this downdraft vent must conform to

the Manufactured Home Construction Safety Standards,

Title 24 CFR, Part 328 (formerly the Federal Standard for

Mobile Home Construction and Safety, title 24, HUD, Part 280)

or when such standard is not applicable, the standard for

Manufactured Home Installation 1982 (Manufactured Home

Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or

latest edition, or with local codes.

Product Dimensions

Cabinet Dimensions

NOTES:

■ See cooktop manufacturer’s instructions for cooktop cutout

depth and width.

■ Use dimensions for vent system cutout location that applies

to your installation.

■ Interior mounted blower systems connect with 3¹⁄₄" x 10"

(8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent system.

The cutout locations for this vent system will depend on your

specific installation.

Top trim widths:

30" (76.2 cm)

36" (91.4 cm)

13¹⁄₂" (34.3 cm)

retractable

vent height

27" (68.6 cm) for 30" (76.2 cm) vent

33" (83.8 cm) for 36" (91.4 cm) vent

16¹⁄₂" (42.0 cm)

10"

(25.4 cm)

2¹⁄₈" (5.4 cm)

28¹⁄₂"

(72.4 cm)

³⁄₈" (0.95 cm)

1¹⁄₂" (3.8 cm)

13¹⁄₈" (33.4 cm)

5¹⁄₄"(13.3 cm)

for 30" (76.2 cm) vent

8¹⁄₄"(21.0 cm)

for 36" (91.4 cm) vent

³⁄₄

(1.9 cm)

A= ¹⁄₂" (12.7 mm)

minimum

21⁵⁄₁₆"

(54.1 cm)

Cutouts are

for 3¹⁄₄" x 10"

(8.3 x 25.4 cm)

rectangular or 6"

(15.2 cm) round

vent system.

Centerline of cooktop cutout

21⁵⁄₁₆"

(54.1 cm)

Locate power

supply junction

box at lower

left hand

rear corner

of the cabinet.

10" (25.4 cm)

Countertop Cutout Dimensions

IMPORTANT: Countertops with a bull-nosed front edge are not recommended for these installations.

Some models require a countertop deeper than 25" (63.5 cm); see the following “Countertop Cutout Dimensions Chart.”

To avoid mistakes, it is recommended that the cooktop and vent cutouts be drawn on the countertop before making any cutouts.

See the Installation Instructions that came with your cooktop for complete cutout dimensions, location dimensions and installation

details.

Countertop Cutout Dimensions Chart

A. Downdraft vent

B. Cooktop

C. Measurement of cooktop rear overhang

D. D = Measurement of cooktop rear overhang (C)

+ 1

¹³⁄₁₆

" [46.2 mm] (E)

E. 1

¹³⁄₁₆

" (46.2 mm)

F. ½" (12.7 mm) minimum

G. ¼" (6.4 mm) minimum

H. Countertop and backsplash

I. ½" (12.7 mm) minimum

A. ½" (12.7 mm) minimum to

backsplash or rear wall

³⁄₄

" (19.1 mm) maximum

backsplash depth

C. 27

¹⁄₂

" (69.9 cm) on 30" (76.2 cm) models

¹⁄₂

" (85.9 cm) on 36" (91.4 cm) models

D. D = Measurement of cooktop rear overhang

+ 1

¹³⁄₁₆

" (46.2 mm)

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest

edition), or CSA Standards C22.1-94, Canadian Electrical Code,

Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes

and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■ A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

■ If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial rating plate.

The model/serial plate is located on the front of the downdraft

vent, above the wiring box cover.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22. 1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

Venting Requirements

IMPORTANT: Make sure there is proper clearance within the wall

or floor before making exhaust vent cutouts.

■ Use heavy (rigid) metal vent.

■ Venting system must terminate to the outside.

■ Do not terminate the vent system in an attic or other enclosed

area.

■ Do not use 4" (10.2 cm) laundry-type wall caps.

■ Do not install 2 elbows together.

■ Do not use plastic or metal foil vent.

■ The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

■ Use no more than three 90° elbows

■ Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than one elbow is used.

■ Use clamps or duct tape to seal all joints in the vent system.

■ Use caulking tape to seal the exterior wall or floor opening

around cap.

■ Do not cut joist or stud. If vent cutout falls over a joist or stud,

a supporting frame must be constructed.

Flexible metal vent is not recommended. If it is used, calculate

each foot of flexible vent as 2 ft (0.6 m) of rigid metal vent.

Flexible elbows count twice as much as standard elbows.

Recommended vent system length:

For either interior-mounted or exterior-mounted blower

installations, the vent system length should not exceed the

maximum lengths listed in the Maximum Length of Vent System

chart. See “Calculating Vent System Length” in the “Venting

Methods” section in the Installation Instructions.

Cold Weather Installations

An additional back draft damper should be installed to minimize

backward cold air flow and a thermal break should be installed to

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup Air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

INSTALLATION INSTRUCTIONS

Venting Methods

Determine which venting method is best for your application.

Vent system can terminate either through the wall or floor.

Island Location

NOTE: For island locations, a front- or rear-mounted blower

motor can also be mounted for right or left venting if needed for

your application. Most island applications would still require the

venting to be directed down through the floor.

Built-In Cabinet Locations

Island Location—Vent System Installed Under a Concrete

Slab Using PVC Sewer Pipe

Front (Standard) Mounted Blower Motor

Rear Mounted Blower Motor

Calculating Vent System Length

3¼" x 10" (8.3 x 25.4 cm) rectangular vent is required from the

blower motor box. It can be transitioned to 6" (15.2 cm) round

vent if needed.

Maximum Length of Vent System

Front (Standard)-Mounted

Blower Motor

Rear-Mounted Blower Motor

A. Down vent

B. Left vent

C. Right vent

A. Wall cap

B. 6" (15.2 cm) round metal vent

C. 16" (40.6 cm) maximum

D. 6" (15.2 cm) round PVC sewer pipe

E. 6" (15.2 cm) round metal vent transition with damper (supplied)

F. 6" (15.2 cm) round PVC coupling

G. Concrete slab

H. 6" (15.2 cm) round PVC sewer pipe

I. 6" (15.2 cm) round 90° PVC sewer pipe elbow

J. Tightly pack gravel or sand completely around pipe.

K. 6" (15.2 cm) round 90° PVC sewer pipe elbow

L. 6" (15.2 cm) round PVC coupling

M. 12" (30.5 cm) minimum

Vent Length

6" (15.2 cm) round 35 ft (8.9 m)

3¹⁄₄" x 10" (8.3 cm x 25.4 cm) 35 ft (8.9 m)

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Example Vent System

The following example falls within the maximum vent length of

35 ft (8.9 m).

Install Vent System

1. Place cardboard or similar material on top of a flat surface

where you can easily assemble the downdraft vent system.

2. Remove parts packages, downdraft vent and blower box

from the carton.

3. Remove all shipping materials, tape and film from the

downdraft vent and blower box.

Vent Piece

3¹⁄₄" x 10" (8.3 cm x 25.4 cm)

Rectangular

3¹⁄₄" x 10" (8.3 cm x 25.4 cm)

90° elbow

5.0 ft

(1.5 m)

3¹⁄₄" x 10" (8.3 cm x 25.4 cm)

flat elbow

12.0 ft

(3.7 m)

3¹⁄₄" x 10" (8.3 cm x 25.4 cm)

wall cap

0.0 ft

(0.0 m)

Vent Piece 6" (15.2 cm) Round

45° elbow 2.5 ft

(0.8 m)

90° elbow 5.0 ft

(1.5 m)

6" (15.2 cm)

wall cap

0.0 ft

(0.0 m)

3¹⁄₄" x 10" (8.3 cm x 25.4 cm)

to 6" (15.2 cm) transition

4.5 ft

(1.4 m)

6" (15.2 cm) to 3¹⁄₄" x 10"

(8.3 cm x 25.4 cm) transition

1 ft

(0.3 m)

3¹⁄₄" x 10" (8.3 cm x 25.4 cm)

to 6" (15.2 cm) 90° elbow

transition

5.0 ft

(1.5 m)

6" (15.2 cm) to 3¹⁄₄" x 10"

(8.3 cm x 25.4 cm) 90° elbow

transition

5.0 ft

(1.5 m)

A. Blower motor

B. Transition

C. 90° elbows

D. Back draft damper

2 - 90° elbow = 10.0 ft (3 m)

1 - wall cap = 0.0 ft (0.0 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

Transition = 4.5 ft (1.4 cm)

Length of 6" (15.2 cm) or

3¹⁄₄" x 10"

(8.3 cm x 25.4 cm)

system

= 22.5 ft (6.8 m)

6 ft

(1.8 m)

2 ft (0.6 m)

WARNING

Excessive Weight Hazard

Use two or more people to move and install

downdraft vent.

Failure to do so can result in back or other injury.

4. Install the right and left undercounter mounting brackets to

the vent box. Slide the keyhole slots over the guide tabs and

push the brackets up to set them into place.

5. Attach the right and left end caps to the vent box. Place the

tab into the mounting slot at each end of the downdraft vent

as shown and push down to lock into place.

6. Measure distance “X” from the cabinet floor to the top of the

countertop. Subtract 28¹⁄₂" from distance “X” to determine

dimension “Y” (X - 28¹⁄₂ = Y).

7. Attach the support legs to the side of the vent box with

4 - 4 x 8 mm screws in each support leg. Adjust to dimension

“Y” from the bottom of the vent box to the bottom of the

support legs. Tighten screws.

Determine Which Vent Direction Is Best For Your

Installation

When installed in a cabinet, vent system can exhaust through the

bottom, right or left of the cabinet.

IMPORTANT: When using the 6" (15.2 cm) vent transition

(supplied) for 6" round venting, only left or right venting is

recommended.

Bottom Venting:

NOTE: If installing the vent damper in the down position, a wall or

roof cap with a damper at the exit end of the vent system is

required.

■ Downdraft vent is shipped with blower in down venting

position so no modification is required.

■ If rear mounting of the blower motor is not required, go to

the “Complete Installation” section.

■ To mount the blower motor to the rear side of the vent

box, go to the “Rear Mounting - Blower Motor” section.

A. Vent box

B. Undercounter mounting bracket

C. Keyhole slots

D. Guide tabs

A. End cap tab

B. Mounting slot

Cabinet floor

Top of countertop

Downdraft vent

“X”

“Y”

28¹⁄₂"

(73 cm)

A. Motor box

B. Support leg

C. 4 x 8 mm screws (4)

Dim. “Y”

Left or Right Venting:

1. Using two or more people, place the downdraft vent system

on its back.

2. Remove the 4 screws from the cover plate mounted to the

face of the motor box and set them aside.

3. Slide the cover plate up and slip it over the keyhole slot

shoulder screws. Set the cover aside.

4. Remove 4 screws from the bottom of the motor box that hold

the motor assembly to the motor box.

NOTE: Disconnect the electrical wiring connection from

motor if needed.

5. Remove 3 screws and the vent cover plate from the left or

right side of the motor box for the venting direction to be

used.

6. Rotate the blower motor assembly 90 degrees to the left or

right side to the chosen venting direction and secure to the

blower box with motor mounting screws previously removed.

Do not twist or bind the wires.

7. Install the vent cover plate over the rectangular opening in the

bottom of the motor box and secure with vent cover screws.

NOTE: Reinstall the electrical wiring connection to motor if

removed.

8. Reinstall the cover plate to the face of the motor box and

secure with 4 cover plate screws previously removed.

9. For mounting the blower motor to the back of the vent box,

go to the “Rear Mounting—Blower Motor” section.

Otherwise, go to the “Complete Installation” section.

Rear Mounting—Blower Motor

NOTE: Optional blower motor rear mounting position (opposite

side) for island cabinet locations. The blower motor box

assembly can be moved to the opposite side (rear) of the vent

box.

1. Remove 7 screws from the mounting flanges of the blower

motor box.

Front View

2. Lift blower motor box off the shoulder screws in the keyhole

slots. Disconnect wire connection from blower motor and set

blower motor box aside.

3. Remove 6 screws from the mounting flange of the

¼" (6.4 mm) deep cover.

Rear View

A. Cover plate

B. Cover plate screws (4)

C. Cover plate keyhole slot shoulder

screws (4)

D. Motor mounting screws (4)

E. Vent cover plate

F. Motor box

G. Vent cover screws (3)

A. Screws (7)

B. Keyhole slot shoulder screws (2)

C. Blower motor box

A. Screws (6)

B. Keyhole slot shoulder screws (2)

C. ¼" (6.4 mm) deep cover

4. Lift the ¼" (6.4 mm) deep cover off the shoulder screws in the

keyhole slots and set the cover aside.

5. Remove the screws from the wire mounting plate.

6. Hold the wire mounting plate and push the grommet out of

the mounting plate.

7. Slide the wire assembly through the slot in the wire mounting

plate to remove it.

8. Place the wire assembly through the opening to the opposite

side of the vent box.

9. Reassemble the wire assembly and grommet to the wire

mounting plate.

10. Install the wire mounting plate to the vent box using the

4 screws previously removed.

11. Place the blower motor box assembly with the keyhole slots

over the 2 shoulder screws on the rear of the vent box and

reconnect the wire connection to the blower motor.

12. Mount the blower motor box to the vent box and secure using

the 6 screws previously removed.

13. Mount the 4³⁄₄" (12.0 cm) cover box (supplied) to the front of

the vent box. Place the keyhole slots over the 2 shoulder

screws, align the mounting holes, and secure the cover box

to vent box using the 6 screws previously removed from the

¼" (6.4 mm) deep cover.

14. Go to the “Complete Installation” section.

Complete Installation

NOTE: The downdraft vent system is supplied with a 3¹⁄₄" x 10"

(8.3 x 25.4 cm) back draft damper and a 6" (15.2 cm) round vent

transition with damper. Refer to “3¹⁄₄" x 10" (8.3 x 25.4 cm) back

draft damper” or “6" (15.2 cm) round vent transition with

damper,” depending upon the type of venting you are using.

3¹⁄₄" x 10" (8.3 x 25.4 cm) Back Draft Damper

1. Attach the 3¼" x 10" (8.3 x 25.4 cm) back draft damper to the

vent opening in the blower motor box, using three

3.5 x 9.5 mm screws.

6" (15.2 cm) Round Vent Transition With Damper

1. Attach the 6" (15.2 cm) round vent transition to vent opening

(left or right side venting only is recommended), using two

3.5 x 9.5 mm screws.

A. Screws

B. Wire mounting plate

C.Blower motor box

A. Wire mounting plate

B. Grommet

A. 3.5 x 9.5 mm screws

B. 3¼" x 10" (8.3 x 25.4 cm)

back draft damper

A. 3.5 x 9.5 mm screws

B. 6" (15.2 cm) round vent transition with damper

2. Remove 4 screws attaching the terminal box cover.

3. Determine which direction (front or rear) the home power

supply cable will enter the terminal box. Remove the

appropriate knockout from the front or rear panel and install a

¹⁄₂" (12.7 mm) UL listed or CSA approved conduit connector.

4. Using 2 or more people, insert the downdraft vent into the

countertop cutout. Position downdraft vent so it is centered

in the cutout with the rear flange over the edge of the cutout

and the rear of the vent box against the edge of the cutout.

5. Drill 2 pilot holes through each of the undercounter mounting

brackets into the underside of the countertop. Using 2 screws

(not provided) of the appropriate length, mount the brackets

to the countertop.

IMPORTANT: Select a screw length that will not allow the

screws to go through the countertop when tightened.

6. Check that the downdraft vent is level vertically. Loosen the

lower support legs screws and position the legs against the

cabinet floor.

7. Fasten the lower support legs to the cabinet floor with screws

(not provided).

8. Tighten the lower support legs screws.

Make Electrical Connections

1. Disconnect power.

A. Terminal box cover

A. Rear flange of downdraft vent

B. Edge of cutout in countertop

C. Rear of downdraft vent

D. Cabinet back

E. Lower support leg

F. Cabinet floor

G. Countertop

A. Screws

B. Backsplash

C. Countertop

A. Screw (not provided)

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

2. Feed the power supply cable through the conduit connector

and into the terminal box.

3. Connect the green (or green/yellow) ground wire to the green

or yellow/green ground wire using UL listed wire connectors.

Tighten the screw on the conduit connector.

4. Connect the 2 white wires together using UL listed wire

connectors.

5. Connect the 2 black wires together using UL listed wire

connectors.

6. Replace the terminal box cover and secure with screw.

7. Reconnect power.

Check Operation

1. Push and hold the button on the top of the downdraft vent for

a few seconds. The retractable section of the downdraft vent

will rise, and the blower will start. Position the top trim over

the retractable section and snap trim into place.

Trim kits for matching your cooktop color are available from

your dealer.

For information on ordering, see the “Assistance or Service”

section.

2. Slide the control slider on the side of vent to check the

operation and speed of the blower.

3. If the blower does not operate:

■ Check that filter or filters are pressed in as far as they will

go.

■ Check that the circuit breaker has not tripped or a

household fuse blown.

4. Connect vent system to blower. Vent system must end with a

wall or roof cap. Use clamps or duct tape to seal all joints.

5. Install cooktop according to manufacturer’s instructions.

Check that rear of cooktop overlaps edge of retractable

downdraft vent by ³⁄₈" (9.5 mm). See “Countertop Cutout

Dimensions” in the “Location Requirements” section.

NOTE: To get the most efficient use from your new retractable

downdraft vent, read the “Vent System Use” section.

VENT SYSTEM USE

The retractable downdraft vent system is designed to remove smoke, cooking vapors and odors from the cooktop area.

■ For best results, the vent should be operating before cooking

is started.

■ If you use large or tall utensils, place them on the large rear

element or burner surface.

■ A higher heat setting than normally used may be needed

when the downdraft vent is operating.

■ For gas cooktops, the downdraft vent system may affect the

flame stability and cooking performance. To improve the

burner performance, either decrease the downdraft vent

blower speed or increase the cooktop burner flame setting.

■ For gas cooktops with flame sensing ignitions, the downdraft

vent system may disperse the flame away from the spark

igniter and may cause it to continually spark while trying to

reignite a burner that is already lit. To resolve the issue of the

cooktop igniter continuously sparking, either decrease the

downdraft vent blower speed or increase the cooktop flame

setting for that burner.

WARNING

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire

in terminal box.

Failure to do so can result in death or electrical shock.

A. Green or green and yellow

ground wire

B. White wires

C. UL listed wire connectors

D. Black wires

E. UL listed or CSA approved

conduit connector

F. Downd raft vent wir ing

A. Top trim

B. ON/OFF button

C. Blower control slider

D. End cap

E. Filters

Operating Downdraft Vent

To Use:

1. Push and hold the button on top of downdraft vent for a few

seconds. (This slight delay helps avoid unintentional raising of

the vent during cleaning of the cooktop area.) Retractable

section of downdraft vent will rise. Blower will begin to vent

immediately if blower control knob slider is set to an “On”

position.

2. Slide the control slider on the right-hand side of the

downdraft vent to adjust the blower motor speed.

When Cooking Is Complete:

1. Push the button on top of the retractable downdraft vent. The

blower will turn off, and the retractable section of the vent will

return to the closed position.

NOTE: If a spill occurs on the cooktop that allows liquids to seep

inside the downdraft vent, you must turn the downdraft vent off

immediately. It is possible to cause damage to the downdraft

vent if water is allowed inside the downdraft vent while it is

operating.

2. Immediately turn off the downdraft vent at the speed control

located on the right-hand side of the downdraft vent.

3. Turn off the power supply to the downdraft vent at the circuit

breaker box or fuse box.

4. Allow plenty of time for the downdraft vent to dry naturally. Do

not open the downdraft vent to remove the water.

VENT SYSTEM CARE

Surface of Downdraft Vent

To avoid damaging the finish, clean downdraft vent with soap and water. Do not use scouring powder or abrasive solutions.

Exterior Surfaces:

■ To avoid damage to the exterior surface, do not use steel

wool or soap-filled scouring pads.

■ Always wipe dry to avoid water marks.

Cleaning Method:

■ Liquid detergent soap and water, or all-purpose cleanser

■ Wipe with damp soft cloth or nonabrasive sponge, then rinse

with clean water and wipe dry.

Filters

Frequently remove and clean the filter(s) in the retractable section of the downdraft vent. This will improve the operating efficiency of the

downdraft vent system.

To Replace:

1. Remove each filter by pulling the spring release handle and

then pulling down the filter.

2. Wash metal filters as needed in dishwasher or hot detergent

solution.

3. Reinstall the filter by making sure the spring release handles

are toward the front. Insert metal grease filter into upper

track.

4. Pull the spring release handle down.

5. Push up on metal filter and release handle to latch into place.

6. Repeat steps 1-5 for the other filter.

To Clean:

1. Remove the filter(s) and clean them in a dishwasher or in a

hot detergent solution. The downdraft vent will not operate

when the filters are not in place.

2. Dry the clean filter(s) and reinstall, making sure that they lock

into place.

If Retractable Downdraft Vent Does Not Operate After

Clean Filters Have Been Installed:

Push the filter in as far as it will go. When the filter is removed, the

microswitch behind the filter is inactivated. This feature will not

allow the vent system to operate until the filter is properly

installed.

A. Spring release handles

B. Left metal filter

C. Right metal filter

WIRING DIAGRAM

S50

Y/G

Neutral

4˚ Speed

3˚ Speed

2˚ Speed

1˚ Speed

BUBU

GY GY

BR BR

Y/G

SEL0015061

NOTE: Wiring diagram is drawn

with plenum in down position.

Com

ComCom

N.C.

N.O.

N.O.N.O.

N.O.

N.C.

Motor Specifications

Power supply 120 VAC

Frequency

60 Hz

Wattage rating

420 W

Amperage 3.7 A

Motor Resistance

BU/W 21.6 Ohms

BU/R 18 Ohms

BU/GY 14.3 Ohms

BU/BK 9.8 Ohms

Component Layout

Num.

Description

Filter microswitch

Plenum down limit switch

Plenum up limit switch

Motor microswitch

Plenum drive motor

Blower motor

Blower speed switches

Start sw. - plenum up/down

Blower Switch Operation

Contact

Function

1 - 3

OFF

3 - 5

1st Speed

5 - 7

2nd Speed

3rd Speed

8 - 10

10 - 12

4th Speed

ASSISTANCE OR SERVICE

When calling for assistance or service, please know the purchase

date and the complete model and serial number of your

appliance. This information will help us to better respond to your

request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new appliance. To locate factory

specified replacement parts in your area, call us or your nearest

designated service center.

In the U.S.A.

Call the Whirlpool Customer eXperience Center

toll free: 1-800-253-1301.

Our consultants provide assistance with:

■ Features and specifications on our full line of appliances.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

■ Referrals to local dealers, repair parts distributors and service

companies. Whirlpool designated service technicians are

trained to fulfill the product warranty and provide after-

warranty service, anywhere in the United States.

To locate the Whirlpool designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

For further assistance

If you need further assistance, you can write to Whirlpool

Corporation with any questions or concerns at:

Whirlpool Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

In Canada

Call the Whirlpool Canada LP Customer eXperience Centre toll

free: 1-800-807-6777.

Our consultants provide assistance with:

■ Features and specifications on our full line of appliances.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Referrals to local dealers, repair parts distributors, and

service companies. Whirlpool Canada LP designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to Whirlpool

Canada LP with any questions or concerns at:

Customer eXperience Centre

Whirlpool Canada LP

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Accessories

NOTE: Instructions are included with each kit.

For Model Series UXD8630DY

30" (76.2 cm) One-Piece Top Trim

Order Part Number W10387678 (black)

Order Part Number W10388421 (white)

For Model Series UXD8636DY

36" (91.4 cm) One-Piece Top Trim

Order Part Number W10387679 (black)

Order Part Number W10388422 (white)

WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for Factory Specified Parts

and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.

This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the country in

which it was purchased. Outside the 50 United States and Canada, this limited warranty does not apply. Proof of original purchase date

is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use or when it is used in a manner that is

contrary to published user or operator instructions and/or installation instructions.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved by Whirlpool.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.

6. Any food loss due to refrigerator or freezer product failures.

7. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be

repaired in the home and only in-home service is covered by this warranty.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Whirlpool servicer is not available.

10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with published installation instructions.

11. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty

is void if the factory applied serial number has been altered or removed from your major appliance.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.

If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” you may find

additional help by checking the “Assistance or Service” section or by calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada,

call 1-800-807-6777.

9/07

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name____________________________________________________

Address ________________________________________________________

Phone number__________________________________________________

Model number __________________________________________________

Serial number __________________________________________________

Purchase date __________________________________________________

SÉCURITÉ DU SYSTÈME DE VENTILATION

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

IMPORTANTES INSTRUCTIONS DE SÉCURITÉ

LIRE ET CONSERVER CES INSTRUCTIONS

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE

D'INCENDIE, CHOC ÉLECTRIQUE OU DOMMAGES

CORPORELS, RESPECTER LES INSTRUCTIONS

SUIVANTES :

■ Utiliser cet appareil uniquement dans les applications

envisagées par le fabricant. Pour toute question, contacter

le fabricant.

■ Avant d'entreprendre un travail d'entretien ou de nettoyage,

interrompre l'alimentation de la hotte au niveau du tableau

de disjoncteurs, et verrouiller le tableau de disjoncteurs

pour empêcher tout rétablissement accidentel de

l'alimentation du circuit. Lorsqu'il n'est pas possible de

verrouiller le tableau de disjoncteurs, placer sur le tableau

de disjoncteurs une étiquette d'avertissement proéminente

interdisant le rétablissement de l'alimentation.

■ Tout travail d'installation ou câblage électrique doit être

réalisé par une personne qualifiée, dans le respect des

prescriptions de tous les codes et normes applicables, y

compris les codes du bâtiment et de protection contre les

incendies.

■ Ne pas faire fonctionner un ventilateur dont le cordon ou la

fiche est endommagé(e). Jeter le ventilateur ou le retourner

à un centre de service agréé pour examen et/ou réparation.

■ Une source d'air de débit suffisant est nécessaire pour le

fonctionnement correct de tout appareil à gaz (combustion

et évacuation des gaz à combustion par la cheminée), pour

qu'il n'y ait pas de reflux des gaz de combustion. Respecter

les directives du fabricant de l'équipement de chauffage et

les prescriptions des normes de sécurité - comme celles

publiées par la National Fire Protection Association (NFPA)

et l'American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), et les prescriptions des

autorités réglementaires locales.

■ Lors d'opérations de découpage et de perçage dans un mur

ou un plafond, veiller à ne pas endommager les câblages

électriques ou canalisations qui peuvent s'y trouver.

■ Les ventilateurs d'évacuation doivent toujours décharger

l'air à l'extérieur.

MISE EN GARDE : Cet appareil est conçu uniquement

pour la ventilation générale. Ne pas l'utiliser pour l'extraction

de matières ou vapeurs dangereuses ou explosives.

MISE EN GARDE : Pour minimiser le risque d'incendie

et évacuer adéquatement les gaz, veiller à acheminer l'air

aspiré par un conduit jusqu'à l'extérieur - ne pas décharger

l'air aspiré dans un espace vide du bâtiment comme une

cavité murale, un plafond, un grenier, un vide sanitaire ou

un garage.

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE

D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

MÉTALLIQUES.

AVERTISSEMENT : POUR MINIMISER LE RISQUE

D'UN FEU DE GRAISSE SUR LA CUISINIÈRE :

■ Ne jamais laisser un élément de surface fonctionner à

puissance de chauffage maximale sans surveillance. Un

renversement/débordement de matière graisseuse pourrait

provoquer une inflammation et la génération de fumée.

Utiliser une puissance de chauffage moyenne ou basse

pour le chauffage d'huile.

■ Veiller à toujours faire fonctionner le ventilateur de la hotte

lors de la cuisson avec une puissance de chauffage élevée

ou lors de la cuisson d'un mets à flamber (à savoir crêpes

Suzette, cerise jubilée, steak au poivre flambé).

■ Nettoyer fréquemment les ventilateurs d'extraction. Veiller à

ne pas laisser la graisse s'accumuler sur les surfaces du

ventilateur ou des filtres.

■ Utiliser toujours un ustensile de taille appropriée. Utiliser

toujours un ustensile adapté à la taille de l'élément

chauffant.

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE DE

DOMMAGES CORPORELS APRÈS LE DÉCLENCHEMENT

D'UN FEU DE GRAISSE SUR LA CUISINIÈRE, APPLIQUER

LES RECOMMANDATIONS SUIVANTES :

■ Placer sur le récipient un couvercle bien ajusté, une tôle à

biscuits ou un plateau métallique POUR ÉTOUFFER LES

FLAMMES, puis éteindre le brûleur. VEILLER À ÉVITER

LES BRÛLURES. Si les flammes ne s'éteignent pas

immédiatement, ÉVACUER LA PIÈCE ET APPELER LES

POMPIERS.

■ NE JAMAIS PRENDRE EN MAIN UN RÉCIPIENT

ENFLAMMÉ - vous risquez de vous brûler.

■ NE PAS UTILISER D'EAU, ni un torchon humide - ceci

pourrait provoquer une explosion de vapeur brûlante.

■ Utiliser un extincteur SEULEMENT si :

– Il s'agit d'un extincteur de classe ABC, dont on connaît le

fonctionnement.

– Il s'agit d'un petit feu encore limité à l'endroit où il s'est

déclaré.

– Les pompiers ont été contactés.

– Il est possible de garder le dos orienté vers une sortie

pendant l'opération de lutte contre le feu.

Recommandations tirées des conseils de sécurité en cas

d'incendie de cuisine publiés par la NFPA.

■ AVERTISSEMENT : Pour réduire le risque d'incendie

ou de choc électrique, ne pas utiliser ce ventilateur avec un

quelconque dispositif de réglage de la vitesse à semi-

conducteurs.

Page is loading ...

Maytag UXD8630DYS User guide

Brand: Maytag

Model: UXD8630DYS

Type: User guide

This manual is also suitable for

Download PDF

report

in other languages

français: Maytag UXD8630DYS Mode d'emploi

Maytag UXD8630DYS User guide

This manual is also suitable for

Maytag UXD8630DYS User guide

in other languages

Related papers

Other documents