Harbor Freight Tools 30 in. Large 350 lb. Capacity Glossy Red Service Cart With Locking Drawer User manual

Category
Multimedia carts & stands
Type
User manual
Service Cart with Drawer
90428 Service Cart
INSTRUCTIONS AND PRECAUTIONS
Visit our website at:
http://www.harborfreight.com
Read this material before
using this product.
Failure to do so can result
in serious injury.
SAVE THIS MANUAL.
When unpacking, make sure
that the product is intact and
undamaged.
If any parts are missing or broken,
please call 1-800-444-3353
as soon as possible.
Copyright
©
2011 by Harbor Freight Tools
®
. All rights reserved. No
portion of this document or any artwork contained herein may
be reproduced in any shape or form without the express written
consent of Harbor Freight Tools. Diagrams within this document
may not be drawn proportionally. Due to continuing improvements,
actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
For technical questions or replacement
parts, please call 1-800-444-3353.
Specications
Capacity 350 LB.
Tray Depth 3 IN.
Wheels 4 IN. dia
Dimensions 30 x 16 x 35-5/16 IN.
Drawer Lockable with two keys
Important Safety Information
Precautions
1. Do not ride or climb on cart. Keep away from children.
2. Do not exceed 350 lb. capacity, evenly distributed.
3. Use only on a at, level surface able
to support Cart and load.
4. Wear ANSI-approved safety goggles during assembly.
5. Inspect before every use; do not use
if parts are loose or damaged.
6. Maintain product labels and nameplates. These carry
important safety information. If unreadable or missing,
contact Harbor Freight Tools for a replacement.
Page 2 For technical questions, please call 1-800-444-3353. SKU 90428
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY
INFORMATION section at the beginning
of this document including all text
under subheadings therein before
set up or use of this product.
Note: You will need 10mm, 14mm and 17mm
sockets and/or end wrenches for assembly.
1. Unwrap and separate all parts on a clear work area.
2. Attaching the Handles and Upper Shelf
Slide each set of
Handles (1)
through the
corner slots in the
Upper Shelf (15)
and align the
holes nearest the
curved handle
section with the
holes in the side
of the Shelf. Bolt
in place using
four of the 1-1/2"
Bolts (16), Small
Washers (2), and
Nuts (3).
3. Attaching the Drawer Frame
Slide the Drawer
Frame (5a) up to
the under side of
the Upper Shelf
(15), aligning the
holes in the
Drawer Frame
with the four holes
in the bottom of
the Upper Shelf.
Secure in place
using 3/4" Bolts
(7), Large
Washers (8), and
Nuts (9).
4.
5. Attaching the drawer.
Slide the Drawer
(5) into the
Drawer Frame
and lock in place
with the Key
(10).
6. Attaching the
Lower Shelf
Slide the Handle ends
through the corner slots
in the Lower Shelf
(15a) and align the
remaining holes. Bolt in
place using four of the
1-1/2” Bolts (16), Small
Washers (2), and Nuts
(3).
Note: Check that the unit is square and the drawer slides
easily. Retighten all bolts if needed to adjust the cart.
7. Installing the Wheels
The Service Cart has two locking Swivel
Casters (12) and two non-locking Swivel
Casters (13). Both Locking Swivel Casters must
be installed at the same end of the Service
Cart. Choose the location of the Locking
Casters before beginning.
Using a rubber mallet (sold separately), insert
the Caster Holders into the ends of the Handles
so that the small holes are at the opening.
Place some grease (sold separately) on the end of the
shank of the Caster, then press the Casters into the
Caster Holders as far as they will go. Use a steel rod
and a rubber mallet to tap the Casters the rest of the
way into the Caster Holder.
Note: The Casters need to be tapped into their slots for
a snug t. The nylon Caster Holder expands as the
Caster is tapped into place, creating a snug t
CAUTION: Do not tap directly on the Caster with the rubber
mallet. The Caster may break.
Page 3For technical questions, please call 1-800-444-3353.SKU 90428
Parts List and Assembly Diagram
Part Description Qty
1 Handle 2
2 Small Washer 8
3 Hex Nut 10mm 8
5 Drawer 1
5a Drawer Frame 1
7 Bolt 3/4" 8
8 Large Washer 8
9 Hex Nut 14mm 8
Part Description Qty
10 Key (not shown) 2
12 Locking Swivel Caster 2
13 Swivel Caster 2
14 Caster Holder 4
15 Upper Shelf 1
15a Lower Shelf 1
16 Bolt 1-1/2" 8
1
9
5a
13 37
15
16 2
15a
14
5
12 8
Record Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and
are not available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Harbor Freight Tools 30 in. Large 350 lb. Capacity Glossy Red Service Cart With Locking Drawer User manual

Category
Multimedia carts & stands
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI