George Kovacs P5271-613-L User manual

Brand: George Kovacs

Model: P5271-613-L

Type: User manual

This manual is also suitable for

P5272-613-L

George Kovacs P5271-613-L is a wall mount lighting fixture. It is dimmable with ELV dimmer switches. The LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached.

IMPORTANT: Fixture should be installed by a qualified

electrician to ensure proper wiring and installation.

Dimmable with ELV dimmer switches.

INSTALLATION INSTRUCTIONS FOR P5271-613-L/P5272-613-L

For Wall Mount Fixture

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

AVE RT I SS E ME N T ! CO U P E R L E C O U RA NT A U N I V E AU D E S FU S I B L E S O U D O D I SJ O N C TE U R .

AV E R T I S S E M E N T ! C O U P E R L E C O U R A N T AU N I V E A U D E S F U S I B L ES O U D O D I S J O N C T E U R .

PREPARATION

1. Shut off power at the fuse box or circuit breaker box. If

necessary remove the old fixture and mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts

on a clear area. Take care not to lose any small parts

necessary for installation.

MOUNTING THE FIXTURE (FIG. 1)

3. Secure mounting back plate (B) to junction box (A) using

junction boxes screws (C) (Size: 8-32*1/2”L). The side of

the mounting back plate marked “GND” must face out.

CONNECTING THE WIRES (FIG. 2)

4. At this point, connect the electrical wires as shown in Fig. 2,

making sure that all wire connectors are secured. If your

outlet has a ground wire (green or bare copper), connect

the fixtures ground wire to it. Otherwise, connect the fixture

ground wire directly to the back plate (B) using the green

screw provided. After wires are connected, tuck them

carefully inside the junction box.

FINISHING THE INSTALLATION (FIG.1)

5. Using allen wrench (G) to loosen allen screw (H) a little.

Push rod (E) upwards and then lean glass shade (F) into

heat sink (D).

6. Tighten rod (E), screw (H) using allen wrench (G).

7. Fix the bracket (J) to back plate (B) by using screws (I).

Note: Back plate is different marked in Fig.1

Your installation is now completed. Return power to the junction box

and test the fixture.

CAUTION /ATTENTION: When handling the fixture, do not

apply pressure to the LEDs. Hold the fixture by the base or

bracket (J).

Replacing LED module (Fig. 3)

The LED module can be replaced by a qualified electrician

without cutting of wire and without damage to any decorative

element to which the fixture is attached. See installation steps

for more details (Fig 3.)

a. Shut off power. Remove the fixture from the wall.

b. Using allen wrench (G) to loosen allen screw (H) a little.

Push rod (E) upwards and then release glass shade (F)

from heat sink (D)(Fig.1).

c. Release black and white wires from quick connector on

LED module with using screwdriver by lightly pressing on

the release button located on the top of the wire connector.

d. Remove screws (M) and washers (K) to disconnect LED

module (N) from heat sink (D).

e. Reverse steps a-d for installing the new LED module.

Note: The LED module should be provided by a specified

supplier.

FIG.1

Set # A-021-125D(P5271-613-L); A-021-170112(P5272-613L)

- Mounting plate - Ground screw

- Mounting screw*2pcs

Fig.2

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

HOUSE

WIRES

Green or

Bare

Copper(G

round)

FIG.3

George Kovacs P5271-613-L User manual

Brand: George Kovacs

Model: P5271-613-L

Type: User manual

This manual is also suitable for

P5272-613-L

Download PDF

report

George Kovacs P5271-613-L User manual

This manual is also suitable for

George Kovacs P5271-613-L User manual

Related papers

Other documents