INSTALLATION INSTRUCTIONS
Item#P1427-674-L (New. 07/07/2018)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig.3
LA-2960E
HANGING THE FIXTURE (Fig. 1)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture including the mounting
hardware.
2. Carefully remove the fixture from the carton and check that all
parts are included as shown in the illustration.
3. Attach the mounting plate (A) to the junction box using
mounting screws (B) (size: #8-32N*L0.5β). The side of the
mounting plate marked βGNDβ must face out.
SUGGESTED INSTALLATION (Fig. 2)
4. Secure metal tube (R) into the nipple (I).
5. Determine the desired hanging height and thread rods (F1, F2,
and F3) to the nipple of the metal tube (R). Pass the wires
carefully through each rod as you assemble.
6. Place the canopy (C) over the rods (F) and thread the hanger
ball (E) to rods (F). Please remove the nipple if installing with
one 6β rod only.
7. Lace the safety cable through the set screw assembly (to the
desired length), and secure it near the end of nipple of hanger
ball (E). Then secure the cable by re-tightening the screws.
Next attach the safety cable to the hanger ball with the screw
provided.
8. While holding the fixture body, install the fixture into the
mounting plate (A) by tilting at a slight angle so that the hanger
ball (E) slips into the mounting plate (A) as shown. Align the
notch in the hanger ball (E) to the tab on the mounting plate (A)
to prevent the fixture from turning.
CONNECTING THE WIRES (Fig. 3)
9. At this point, connect the electrical wires as shown in figure 3,
making sure that all wire connectors are secured. If your outlet
has a ground wire (green or bare copper), connect the ground
wires from the hanger ball and mounting plate to it. Otherwise,
connect the ground wire from the hanger ball directly to the
mounting plate ground wire and secure with the wire connectors
provided. After wires are connected, tuck them carefully into the
ceiling junction box.
COMPLETING THE INSTALLATION (Fig. 1)
10. Place the canopy (C) over the mounting plate (A) and secure
with screws (D).
11. Through the nipple (M) (with the nut side) onto the metal
washer (K), plastic washer (J) and glass shade (H), then secure
them on the coupling (G).
12. Through glass shield (N), into the nipple (M) and secure by
using the finial (P).
Your installation is now complete. Return power and test the
fixture.
CAUTION/ATTENTION: When handling the fixture, do not apply
pressure to the LEDs. Hold the fixture by the base or ceiling pan (I)
only.
Replacing LED module (Fig.4)
The LED module can be replaced by a qualified electrician without
cutting the wires and without damaging the decorative element to
which the fixture is attached. See installation steps for more details
(Fig.4)
Warning: Turn off power at the fuse box or circuit
breaker before replacing the LED module.
a. Loosen finial (P) and remove the glass shield (N).
b. Loosen nipple (M) and remove the metal washer (K), plastic
washer (J) and glass shade (H).
c. Loosen screws (O), then carefully remove the led module (Q)
from the fixture body.
d. Use a pin to press from the hole of the quick connector and
disconnect the black/white wire respectively.
e. Reverse steps a-d for installing the new LED module.
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A
QUALIFIED ELECTRICIAN TO ENSURE PROPER WIRING AND
INSTALLATION.
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Set# LTG BKT 10
- Mounting plate
- Ground screw
- Mounting Screw*2
Rod#W30-1-84*1(F1)
W30-1-84*2(F2)
W30-H-84*1(F3)
Dimmable with ELV and/or LED compatible wall
dimmer switches.
R
I
L
P
E
C
F1
Set Screw Assembly
K
M
H
J
N
B
A
D
F2
F3
G
Screw
Safety cable
Fig.2
Fig.4
A
D
F1
B
E
C
Page: 2/2
LA-2960E
a. Hardware Bag:
A. Mounting Plate*1
D. Screw*2
C. Canopy*1
E. Hanger Ball*1
A
C
D
E
b. Hardware Bag:
F1. ROD 12"*1
F2. ROD 12"*2
F3. ROD 6"*1
F1
F2
F3
M
L
J
K
O
H
N
P
Pin
Q
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
George Kovacs P1839-077 User manual
-
George Kovacs P1426-674-L User manual
-
George Kovacs P1425-674-L User manual
-
George Kovacs P975-647 User manual
-
George Kovacs P971-084 User manual
-
George Kovacs P1243-566-L Installation guide
-
George Kovacs P1801-084 User manual
-
George Kovacs P991-084 User manual
-
George Kovacs P1390-044G-L User manual
-
George Kovacs P7988-077 User manual
