Amana TGP305TT0 Installation guide

Brand: Amana

Model: TGP305TT0

Category: Ovens

Type: Installation guide

This manual is also suitable for

3(}ww

INSTALLATIONINSTRUCTIONS

(76.2CM)FREESTANDINGGASRANGE

with standard clean oven

Table of Contents .................................................. 2

Tothe installer: Please leave this instruction book with the unit.

Tothe consumer: Please read and keep this book for future reference.

W10130752A

TABLEOF CONTENTS

RANGE SAFETY .......................................................................... 2

iNSTALLATiON REQUIREMENTS .............................................. 4

Tools and Parts .......................................................................... 4

Location Requirements .............................................................. 4

Electrical Requirements ............................................................ 6

Gas Supply Requirements ........................................................ 6

iNSTALLATiON iNSTRUCTiONS ............................................ 8

Unpack Range ............................................................................ 8

Install Anti-Tip Bracket .............................................................. 8

Verify Anti-Tip Bracket Location ................................................ 9

Level Range ................................................................................ 9

Make Gas Connection ................................................................ 9

Check Operation ...................................................................... 10

Complete Installation .............................................................. 11

GAS CONVERSIONS ............................................................... 12

LP Gas Conversion .................................................................. 12

Complete Conversion .............................................................. 13

Natural Gas Conversion ........................................................... 14

Complete Conversion .............................................................. 15

RANGESAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

WARNING: If the information in this manual is not followed exactly, a fire or explosion

may result causing property damage, personal injury or death.

= Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

= WHAT TO DO iF YOU SMELL GAS:

• Do not try to light any appliance.

= Do not touch any electrical switch.

• Do not use any phone in your building.

= Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• if you cannot reach your gas supplier, call the fire department.

= Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

In the State of Massachusetts, the following installation instructions apply:

[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

,. Level

[] 3/8"drive ratchet

[] Tape measure

[] Flat-blade screwdriver

[] Phillips screwdriver

[] Hand or electric drill

[] Slip-joint pliers

[] 7 mm combination wrench

[] Pipe wrench

[] 1/_,,(3.2 mm) drill bit (for wood floors)

[] 3A8"(4.8 mm) carbide-tipped masonry drill bit

(for concrete/ceramic floors)

[] Pipe joint compound resistant to LP gas

[] Non-corrosive leak-detection solution

Parts supplied

Check that all parts are included.

A. Anti-tip bracket

B. Plastic anchors (2)

C. #10x 1 1/2" screws (2)

[] Anti-tip brackets must be securely mounted to subfloor.

Thickness of flooring may require longer screws to anchor

bracket to subfloor. Longer screws are available from your

local hardware store.

Parts needed

Check local codes and consult gas supplier. Check existing gas

supply and electrical supply. See "Electrical Requirements" and

"Gas Supply Requirements" sections.

IMPORTANT." Observe all governing codes and ordinances. Do

not obstruct flow of combustion and ventilation air.

[] It is the installer's responsibility to comply with installation

clearances specified on the model/serial rating plate. The

model/serial rating plate is located on the oven frame behind

the left side of the broiler door.

Model/serial

rating plate

location

[] The range should be located for convenient use in the

kitchen.

[] Recessed installations must provide complete enclosure of

the sides and rear of the range.

[] To eliminate the risk of burns or fire by reaching over heated

surface units, cabinet storage space located above the sur-

face units should be avoided. If cabinet storage is to be pro-

vided, the risk can be reduced by installing a range hood that

projects horizontally a minimum of 5" (12.7 cm) beyond the

bottom of the cabinets.

[] All openings in the wall or floor where range is to be installed

must be sealed.

[] Do not seal the range to the side cabinets.

[] Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

[] The floor anti-tip bracket must be installed. To install the anti-

tip bracket shipped with the range, see "Install Anti-Tip

Bracket" section.

[] Grounded electrical supply is required. See "Electrical

Requirements" section.

Proper gas supply connection must be available. See "Gas

Supply Requirements" section.

[] Contact a qualified floor covering installer to check that the

floor covering can withstand at least 200°F (93°C).

[] Use an insulated pad or 1/4"(0.64 cm) plywood under range if

installing range over carpeting.

iMPORTANT." Some cabinet and building materials are not

designed to withstand the heat produced by the oven for baking

and self-cleaning. Check with your builder or cabinet supplier to

make sure that the materials used will not discolor, delaminate or

sustain other damage.

Mobile Home - Additional installation Requirements

The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction and

Safety, Title 24, HUD Part 280). When such standard is not appli-

cable, use the Standard for Manufactured Home Installations,

ANSI A225.1/NFPA 501A or with local codes.

Mobile home installations require:

[] When this range is installed in a mobile home, it must be

secured to the floor during transit. Any method of securing the

range is adequate as long as it conforms to the standards list-

ed above.

ProductDimensions

26-3/4"

(67.9 cm)

depth with

handle

24-1/4" 29-7/8" (75.9 cm)

(61.6 cm) _._" width

42"

(106.7 cm)

overall

height

installation Clearances

Cabinet opening dimensions shown are for 25" (64 cm) counter-

top depth, 24" (61 cm) base cabinet depth and

36" (91.4 cm) countertop height.

If the cabinet depth is greater than 24" (61 cm), the oven frame

must extend beyond cabinet fronts by 1/=,,(13 mm) minimum.

upperside

cabinetto

countertop I

Thisshaded area I

recommendedfor

wall or other com-

bustible material

This shaded area

recommended for

installation

of gas pipe.

10" (25.4 cm)

3" (5.1 cm)

(7.6 cm)---__

NOT_:: 24" (61 cm) minimum when bottom of wood or metal cab-

inet is protected by not less than 1/4"(0.64 cm) flame retardant

millboard covered with not less than No. 28 MSG sheet steel,

0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or

0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the cooking

platform and the bottom of an unprotected wood or metal cabi-

net.

If installing a range hood or microwave hood combination above

the range, follow the range hood or microwave hood combination

installation instructions for dimensional clearances above the

cooktop surface.

ii!!!ili_!_,0ii:i_:_!iiii !!_i!!_qil_i:i_:__ii_i!_!!!%i:_!ii_¸

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

IMPORTANT." The range must be electrically grounded in accor-

dance with local codes and ordinances, or in the absence

of local codes, with the National Electrical Code, ANSI/NFPA 70,

latest edition.

If codes permit and a separate ground wire is used, it is recom-

mended that a qualified electrical installer determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA international

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

[] A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical circuit

is required. A time-delay fuse or circuit breaker is also recom-

mended, it is recommended that a separate circuit serving

only this range be provided.

[] This range is equipped with a power supply cord having a 3

prong ground plug. To minimize possible shock hazard, the

cord must be plugged into a mating 3 prong, grounded outlet.

[] Electronic ignition systems operate within wide voltage limits,

but proper grounding and polarity are necessary. Check that

the outlet provides 120-volt power and is correctly grounded.

This range is equipped with an electronic ignition system that

will not operate if plugged into an outlet that is not properly

polarized.

[] The wiring diagram is located on the back of the range.

NOTE: The metal chassis of the range must be grounded in order

for the control panel to work. If the metal chassis of the range is

not grounded, no keypads will operate. Check with a qualified

electrician if you are in doubt as to whether the metal chassis of

the range is grounded.

Explosion Hazard

Use a new CSA International approved gas supply line.

install a shut=off valve.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances.

IMPORTANT." This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1 - latest edition.

Type of Gas

Natural Gas:

This range is design-certified by the CSA international for use

with natural gas or, after proper conversion, for use with LP gas.

[] This range is factory set for use with natural gas. See "Gas

Conversions" section. The model/serial rating plate located on

the frame behind the broiler door has information on the types

of gas that can be used. Ifthe types of gas listed do not

include the type of gas available, check with the local gas

supplier.

LP Gas conversion:

Conversion must be done by a qualified service technician.

No attempt shall be made to convert the appliance from the gas

specified on the model/serial rating plate for use with a different

gas without consulting the serving gas supplier. See "Gas

Conversions" section.

Gas Supply Line

[] Provide a gas supply line of 3/4"rigid pipe to the range loca-

tion. A smaller size pipe on longer runs may result in insuffi-

cient gas supply. Pipe joint compounds that resist the action

of LP gas must be used. Do not use TEFLON ®ttape. With LP

gas, piping or tubing size can be 1/2"minimum. Usually, LP

gas suppliers determine the size and materials used in the

system.

Flexiblemetalapplianceconnector:

[] Iflocalcodespermit,anewCSAdesign-certified,4-5ft

(122-152.4cm)long,1/2"(1.3cm)or3/4"(1.9cm)I.D.,flexible

metalapplianceconnectormaybeusedforconnectingrange

tothegassupplyline.

[] A1/2"(1.3cm)malepipethreadisneededforconnectionto

thefemalepipethreadsoftheinlettotheappliancegaspres-

sureregulator.

[] Donotkinkordamagetheflexiblemetaltubingwhenmoving

therange.

Rigid pipe connection:

The rigid pipe connection requires a combination of pipe fittings

to obtain an in-line connection to the range. The rigid pipe must

be level with the range connection. All strains must be removed

from the supply and fuel lines so range will be level and in line.

[] Must include a shutoff valve:

The supply line must be equipped with a manual shutoff

valve. This valve should be located in the same room but

external to the range. It should be in a location that allows

ease of opening and closing. Do not block access to shutoff

valve. The valve is for turning on or shutting off gas to the

range.

B ..................

A.Shutoffvalvein "open"position

B.Gassupplyline

C.Torange

Burner input Requirements

Input ratings shown on the model/serial rating plate are for eleva-

tions up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a

rate of 4% for each 1,000 ft (304.8 m) above sea level.

Gas Supply Pressure Testing

Line pressure testing above r/2psi gauge (14" WCP}

The range and its individual manual shutoff valve must be discon-

nected from the gas supply piping system during any pressure

testing of that system at test pressures greater than

rA psi (3.5 kPa).

Line pressure testing at r/2psi gauge (t4" WCP) or lower

The range must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure

testing of that system at test pressures equal to or less than

rA psi (3.5 kPa).

Gas Pressure Regulator

The gas pressure regulator supplied with this range must be

used. The inlet pressure to the regulator should be as follows for

proper operation:

Natural Gas:

Minimum pressure: 5" WCP

Maximum pressure: 14" WCP

LP Gas:

Minimum pressure: 11" WCP

Maximum pressure: 14" WCP

Contact local gas supplier if you are not sure about the inlet pres-

sure.

1-(¢TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

f. Do not use oven door handle to lift or move the range.

2. Remove shipping materials, tape and protective film from

range. Keep cardboard bottom under range. Remove oven

racks and parts package from inside oven.

3. Take 4 cardboard corners from the carton. Stack one card-

board corner on top of another. Repeat with the other 2 cor-

ners. Place them lengthwise on the floor behind the range to

support the range when it is laid on its back. Using 2 or more

people, firmly grasp the range and gently lay it on its back on

the cardboard corners.

4. Pull cardboard bottom firmly to remove.

5. Use an adjustable wrench to loosen the leveling legs. Adjust

the leveling legs to the correct height. Leveling legs can be

loosened to add up to a maximum of 1" (2.5 cm). A maximum

of 3/16" (5 mm) is needed to engage the anti-tip bracket.

NOTE: If height adjustment is made when range is standing, tilt

the range back to adjust the front legs, then tilt forward to adjust

the rear legs.

6. Place cardboard or hardboard in front of range.Using 2 or more

people, stand range back up onto cardboard or hardboard.

A _

A.Cardboardshippingbase

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti=tip bracket, if the range is moved.

Failure to follow these instructions can result in death

or serious burns to children and adults.

Contact a qualified floor covering installer for the best procedure

for drilling mounting holes through your type floor covering.

Before moving range, slide range onto shipping base, cardboard

or hardboard.

f. Remove template from the anti-tip bracket kit (found inside

the oven cavity).

2. Place template on the floor in the cabinet opening so that the

left edge is against the cabinet and the top edge is against

the rear wall, molding or cabinet.

3. Tape template in place.

4. If the countertop is not flush with the cabinet opening edge,

align the template with the overhang.

If the cabinet opening is wider than specified in the "Location

Requirements" section, adjust the template so the range will be

centered in the cabinet opening.

5. To mount the anti-tip bracket to a wood floor, drill two 1/8"

(3.2 mm) holes at the positions marked on the bracket tem-

plate. Remove the template from the floor.

To mount the anti-tip bracket to a concrete or ceramic floor, use

a 3/16" (4.8 mm) masonry drill bit to drill 2 holes at the positions

marked on the bracket template. Remove the template from the

floor.

6. Tap plastic anchors into holes with a hammer.

7. Align the anti-tip bracket holes with the holes in the floor.

Fasten the anti-tip bracket with the screws provided.

Depending on the thickness of your flooring, longer screws may

be necessary to anchor the bracket to the subfloor. Longer

screws are available from your local hardware store.

8. Movetherangeclosetotheopening.Removetheshipping

base,cardboardorhardboardfromundertherange.

9.Openthebroilerdoor.Usea3/8"driveratchettolowerthe

rearlevelinglegsone-halfturn.Useflip-jointplierstolower

thefrontlevelinglegsone-halfturn.

10.Adjusttheleveling

legstothecorrect

height.Levelinglegscanbeloosenedtoadduptoamaxi-

mumof1"(2.5cm).Aminimumof3/16"(5mm)isneededto

engagetheanti-tipbracket.

11.Movetherangeintofinalpositionmakingsuretherearlevel-

inglegslidesintotheanti-tipbracket.

12.Ifinstallingtherangeinamobilehome,youmustsecurethe

rangetothefloor.Anymethodofsecuringtherangeisade-

quateaslongasitconformstothestandardsinthe

"LocationRequirements"section.

13.Continueinstallingyourrangeusingthefollowinginstallation

instructions.

1.Makesuretheanti-tipbracketisinstalled:

[] Lookfortheanti-tipbracketsecurelyattachedtothefloor.

[] Slidetherangebacksotherearrangefootisundertheanti-tip

bracket.

2.Ifinstallingtherangeinamobilehome,youmustsecurethe

rangetothefloor.Anymethodofsecuringtherangeisade-

quateaslongasitconformstothestandardsinthe"Location

Requirements"section.

3.Ifrangeisnotlevel,pullrangeforwarduntilrearlevelinglegis

removedfromtheanti-tipbracket.Uses/8"driveratchetand

slip-jointplierstoadjustlevelinglegsupordownuntilrangeis

level.

4.Pushrangebackintoposition.

5.Checkthatrearlevelinglegisengagedinanti-tipbracket.

NOTE:Rangemustbelevelforsatisfactorybakingperformance.

Typicalrigidpipeconnection

Acombinationofpipefittingsmustbeusedtoconnecttherange

totheexistinggasline.Yourconnectionmaybedifferent;accord-

ingtothesupplylinetype,size,andlocation.

t. ApplypipejointcompoundmadeforusewithLPgastoall

pipethreadconnections.

2. Usingapipewrenchtotighten,connectthegassupplytothe

range.

_ _ ....................S

G .....................

L,J

A. Pressure regulator con- D. Union

nection tiffing E.Nipple

B. 90°elbow E Manual shutoff valve

C. Black iron pipe G. V2"to 3A"gas pipe

Typical flexible connection

t. Use a combination wrench to attach the flexible connector to

the adapters. Check that connector is not kinked.

A.Anti-tipbracket

B.Rangefoot

3. Continue installing your range using the following installation

instructions.

1. Place rack in oven.

2. Place level on rack and check levelness of range, first side to

side; then front to back.

E .............. _ .........................F

b.J

A. Pressure regulator con-

nection tiffing

B. Usepipe joint compound

C. Adapter

D. Flexible connector

E.Adapter

E Use pipe joint compound

G. Manual shutoff valve

H. V2"to 3/4'_gas pipe

Complete Connection

1. Locate gas pressureregulator in the broiler.

A.Gaspressure regu lator

iMPORTANT: Do not remove the gas pressure regulator.

2. Check that the gas pressure regulator shutoff valve is in the

"ON" position.

GasPressureRegulator

Front View / Front Side View//

Shutoff valve "ON" Position

Open the manual shutoff valve in the gas supply line. The

valve is "open" when the handle is parallel to the gas pipe.

Electronic ignition System

Cooktop and oven burners use electronic ignitors in place of

standing pilots. When a cooktop control knob is turned to the

"LITE" position, the system creates a spark to light the burner.

This sparking continues until the control knob is turned to the

desired setting.

When the oven control is turned to the desired setting, a hot sur-

face ignitor heats to a bright orange and ignites the gas. No

sparking occurs. The glow bar remains on while the burner oper-

ates.

Check Operation of Cooktop Burners

1. If control panel and knobs were oo OFF

removed earlier, reinstall knobs, oo

2. Push in and turn each surface

unit control knob to "LITE" posi-

tion. The flame should light with- _0

in 4 seconds.

3. Turn control knob to "HI" posi-

tion after burner lights.

4. Check each cooktop burner for

proper flame. The small inner ME_

cone should have a very distinct blue

flame 1/4"(6.4 mm) to 1A"(13 mm) long. cone

The outer cone is not as distinct as the

inner cone. inner

cone

A. Closed valve

B. Open valve

4. Test all connections by brushing on an approved noncorrosive

leak-detection solution. Bubbles will show a leak. Correct any

leak found.

5. Close the broiler door.

6. Place burners, burner caps and grates on the cooktop.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

7. Plug into a grounded 3-prong outlet.

5. Turn the control knob quickly to the "LO"

position after the burner lights. If the

flame goes out, turn the control knob to the "OFF" position.

6. Check each cooktop burner for proper low flame. The low

flame should be a minimum, steady blue flame. The flame size

should be 1/4"to _/8"(6.4 mm to 9.5 mm) high.

if the low flame needs adjusting:

f. Turn control knob to the "LO" setting and remove control

knob.

2. Insert a small flat-blade screwdriver into the valve stem. Turn

the valve adjusting screw to obtain the smallest flame that will

not go out when the control of a cold burner is quickly turned

from "HI" to "LO". Turn right to decrease flame height. Turn

left to increase flame height. Repeat for other cooktop burners

as needed.

A. Valvestem

3. Replace control knob.

CheckOperationof Oven/Broil Burner

Open broiler door.

Push in and turn the oven control knob to "350°R'' The oven

pilot should now be larger with the flame burning against a

small metal bulb. The oven burner should light in 20-40 sec-

onds; this delay is normal. The oven valve requires a certain

time before it will open and allow gas to flow.

To avoid damaging the hot surface ignitor, do not insert any

object into the openings of the protective shield that sur-

rounds the ignitor or clean that area.

0iF_

14%_

170_

200 0 ROlL

250_ ° 0

300/ ,,

OVENTENP

3. Check the oven burner for proper flame. The flame should be

1/2"(13 mm) long, with inner cone of bluish-green, and outer

mantle of dark blue, and should be clean and soft in charac-

ter. No yellow tips (not enough air), blowing or lifting (too

much air) of flame should occur.

If the flame needs adjusting:

t. Turn the oven off. Wait for the oven burner to cool down.

2o Open oven door and remove oven racks, oven tray, flame

spreader and set aside.

5. Turn the oven back on and check for proper flame. If the

flame is still not properly adjusted, turn the oven off, wait for

the oven burner to cool down and repeat step 4 until flame is

properly adjusted.

6. When the flame has been properly adjusted, turn the oven off,

wait for the burner to cool down.

7. Tighten the shutter screw.

8. Reinstall flame spreader and oven tray. Reinstall the oven

racks and close oven door.

9. Close the broiler door.

1. Check to be sure all parts are now installed. If there is an

extra part, go back through the steps to see which step was

skipped.

2. Check to be sure you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check to be sure the range is level. See "Level Range."

5. Use a mild solution of liquid household cleaner and warm

water to remove waxy residue caused by protective shipping

material. Dry thoroughly with a soft cloth.

6. For range use and cleaning, read the range Use and Care

Guide.

7. Turn on surface burners and oven.

If range does not operate, check the following:

[] Household fuse is intact and tight; or circuit breaker has not

tripped.

[] Range is plugged in to a grounded 3 prong outlet.

[] Electrical supply is connected.

[] See "Troubleshooting" in your Use and Care Guide.

[] When the range has been on for 5 minutes, feel for heat. If

you do not feel heat, turn the range off and check to see that

the gas supply line shutoff valve is open.

[] If the gas supply line shutoff valve is closed, open it, then

repeat the 5-minute test as outlined above.

[] If the gas supply line shutoff valve is open, contact a

qualified technician.

A. Oven tray (lift up at area shown to remove)

B. Screws

C. Flame spreader

Locate the air shutter near the rear wall of oven and loosen

the shutter screw.

A. Shutter screw

B.Air shutter

4. Adjust the air shutter.

GASCONVERSIONS

2. Unplug or disconnect power.

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

NOTE: Gas conversions (from natural gas to LP gas or from LP

gas to natural gas) must be done by a qualified person.

3. Open broiler door and remove broiler pan. The gas pressure

regulator is located in the back right hand corner of the broiler

compartment.

A.Gaspressureregulator

IMPORTANT: Do not remove the gas pressure regulator.

NOTE: Do not remove the spring beneath the cap.

4. Remove the cap from the gas pressure regulator using a flat-

blade screwdriver.

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti=tip bracket, if the range is moved.

Failure to follow these instructions can result in death

or serious burns to children and adults.

To Convert Gas Pressure Regulator

1. Ensure that the manual shutoff valve is in the closed position.

" ,........................................C

A. Shutoff valve in "closed" position

B. Gassupply line

C. Torange

5°

Turn the cap over so that LP is visible.

A. Cap

6. Reinstall the cap.

To Convert Surface Burners

1. Remove burner grate, burner caps, and burners.

.......................................A

A. Burnercap

B.Burner

2. Locate LP gas orifice spuds for top burners in the bag con-

taining literature included with the range. Three LP gas spuds

are stamped "88" and one "96."

3. Remove natural gas orifice spuds using a 7mm combination

wrench.

4. Install LP gas orifice spuds.

NOTE: Depending on model, the range cooktop may be

equipped with 4 standard burners or 3 standard burners and

1 power burner. Spud size/location remain the same.

To Convert Oven Burner

t. Open oven door and remove oven racks, oven tray, flame

spreader and set aside.

2. Lift oven burner. The orifice spud is behind the oven burner air

shutter.

A. Air shutter

3. Locate LP gas orifice spud stamped "56" in literature package

supplied with range.

4. Use a 3/8"combination wrench and remove the natural gas

orifice spud.

5. Install the number "56" LP gas spud.

A. Spud

B. Holder

Std burner88 Std burner88

II II Ill

Powerburner96 Stdburner88

5. Place the natural gas orifice spuds in the parts bag for future

use and keep with bag containing literature.

6. Reinstall burners, burner caps and burner grates.

A. LP oven orifice spud stamped with "56"

IMPORTANT: Do not over tighten.

6. Place natural gas oven burner spud in plastic parts bag along

with natural gas cooktop burner spuds for future use and

keep with bag containing literature.

7. Reinstall oven burner.

8. Reinstall oven racks, oven tray and flame spreader.

t. Refer to the "Make Gas Connection" section for properly

connecting the range to the gas supply.

2. Turn the manual shutoff valve in the gas supply line to the

open position.

3. Refer to the "Check Operation" section for proper burner

ignition, operation, and burner flame adjustments.

IMPORTANT: You may have to adjust the "LO" setting for

each cooktop burner.

Checking for proper cooktop and oven burner flames is very

important. The small inner cone should have a very distinct

blue flame 1/4"to 1/2"(6.4 mm to 13 mm) long. The outer cone

is not as distinct as the inner cone. LP gas flames have a

slightly yellow tip.

4. Close the broiler door and turn the knob to "OFF".

5. Refer to the "Complete Installation" section to complete this

procedure.

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti=tip bracket, if the range is moved.

Failure to follow these instructions can result in death

or serious burns to children and adults.

To Convert Gas Pressure Regulator

t. Ensure that the manual shutoff valve is in the closed position.

.............................. C

B ........................

A.Shutoffvalvein "closed"position

B. Gassupplyline

C. Torange

2. Unplug or disconnect power.

3. Open broiler door and remove broiler pan. The gas pressure

regulator is located in the back right hand corner of the broiler

compartment.

5°

Turn the cap over so that N or NAT is visible.

A. Cap

6. Reinstall the cap.

To Convert Surface Burners

t. Remove burner grates, burner caps, and burners.

.........................................B

A. Burner cap

B. Burner

2. Locate the natural gas orifice spuds for the top burners in the

bag containing literature included with the range. Three

natural gas spuds are stamped "149" and one "165."

3. Remove the LP gas orifice spuds using a 7mm combination

wrench.

A.Gaspressureregularor

iMPORTANT: Do not remove the gas pressure regulator.

NOTE: Do not remove the spring beneath the cap.

4. Remove the cap from the gas pressure regulator using a flat-

blade screwdriver.

4. 4. Usea3/8"combinationwrenchandremovetheLPgasorifice

spud.

Installnaturalgasorificespuds.

NOTE:Dependingonmodel,therangecooktopmaybe

equippedwith4standardburnersor3standardburnersand

1powerburner.Spudsize/locationremainthesame.

Std burner149 Stdburner149

Powerburner165 Stdburner 149

A. Spud

B. Holder

5. Place LP gas orifice spuds in the plastic parts bag for future

use and keep with the bag containing literature.

6. Reinstall burners, burner caps and burner grates.

To Convert Oven Burner

t. Open oven door and remove oven racks, oven tray, flame

spreader and set aside.

2. Lift oven burner. The orifice spud is behind the oven burner air

shutter.

A. Natural gas oven orifice spud stamped with "47"

5. Install the number "47" natural gas spud.

IMPORTANT: Do not over tighten.

6. Place LP gas oven burner spud in plastic parts bag along

with LP gas cooktop burner spuds for future use and keep

with bag containing literature.

7. Reinstall oven burner.

8. Reinstall oven racks, oven tray and flame spreader.

t. Refer to the "Make Gas Connection" section for properly

connecting the range to the gas supply.

2. Turn the manual shutoff valve in the gas supply line to the

open position.

3. Refer to the "Check Operation" section for proper burner

ignition, operation, and burner flame adjustments.

IMPORTANT: You may have to adjust the "LO" setting for

each cooktop burner.

Checking for proper cooktop and oven burner flames is very

important. The small inner cone should have a very distinct

blue flame 1/4"to 1A"(6.4 mm to 13 mm long). The outer cone

is not as distinct as the inner cone. Natural gas flames do not

have yellow tips.

4. Close the broiler door and press the "OFF" pad.

5. Refer to the "Complete Installation" section to complete this

procedure.

A.Airshutter

3. Locate natural gas orifice spud stamped "47" in literature

package supplied with range.

W10130752A

@2007 Whirlpool Corporation

Printed in Mexico

03/2007

Amana TGP305TT0 Installation guide

Brand: Amana

Model: TGP305TT0

Category: Ovens

Type: Installation guide

This manual is also suitable for

Download PDF

report

Amana TGP305TT0 Installation guide

This manual is also suitable for

Amana TGP305TT0 Installation guide

Related papers

Other documents