X750012624
03/13
Water Pump
Operator's Manual
MODEL WP-1000
WP-1000 T1E
WARNING
Users of this equipment risk injury to themselves and others if the unit is used im-
properly and/or safety precautions are not followed. ECHO provides an operator’s
manual. It must be read and understood for proper and safe operation. Failure to
do so could result in serious injury.
X7505120504
2
CopyRight© 2013 By Echo, Incorporated
All Rights Reserved.
Table of ConTenTs
Introduction ................................................................2
- The Operator's Manual .......................................2
Safety .........................................................................3
- Manual Safety Symbols & Important
Information .........................................................3
- Typical Pump Applications ................................. 4
- International Symbols ......................................... 4
- Personal Condition & Safety Equipment ............4
- Equipment ...........................................................6
Emission Control .......................................................6
Description ................................................................. 7
Contents .....................................................................9
Assembly....................................................................9
Suction hose ............................................................... 9
Discharge hose .........................................................10
Operation .................................................................. 11
- Fuel ................................................................... 11
- Priming Pump ...................................................13
- Starting Cold Engine .........................................14
- Starting Warm Engine .......................................15
- Stopping Engine ................................................15
- Cold Weather Operation ...................................15
Maintenance ............................................................. 16
- Skill Levels .......................................................16
- Maintenance Intervals .......................................16
- Air Filter ...........................................................17
- Fuel Filter ..........................................................17
- Spark Plug .........................................................18
- Cooling System Cleaning .................................18
- Exhaust System .................................................19
- Carburetor Adjustment ...................................... 21
- High Altitude Operation ................................. 21
- Pump Casing ..................................................... 23
Troubleshooting .......................................................24
- Troubleshooting Pump End ..............................25
Storage .....................................................................25
Specications ...........................................................27
Warranty Statements ................................................28
Servicing Information ..............................................32
- Parts/Serial Number ..........................................32
- Service ..............................................................32
- Echo Consumer Product Support ......................32
- Warranty Card ...................................................32
- Manual Ordering Instructions ...........................32
Specications, descriptions and illustrative material in
this literature are as accurate as known at the time of
publication, but are subject to change without notice.
Illustrations may include optional equipment and
accessories, and may not include all standard equip-
ment.
InTroduCTIon
Welcome to the ECHO family. is ECHO product was designed and manufactured to provide long life and on-the-
job-dependability. Read and understand this manual. You will nd it easy to use and full of helpful operations tips and
SAFETY messages.
The operaTor's manual
Keep it in a safe place for future reference. Contains specications and
information for safety, operation, maintenance, storage, and assembly
specic to this product.
Water PumP
OPeratOr's manual
3
safeTy
manual safeTy symbols and ImporTanT InformaTIon
WARNING
The safety alert symbol accompanied by the word
“WARNING” calls attention to an act or condi-
tion which CAN lead to serious personal injury or
death if not avoided.
CIRCLE AND SLASH SYMBOL
This symbol means the specic action
shown is prohibited. Ignoring these prohi-
bitions can result in serious or fatal injury.
CAUTION
The safety alert symbol accompanied by the word
“CAUTION” calls attention to an act or condition
which may lead to minor or moderate personal
injury if not avoided.
NOTE
This enclosed message provides tips for use, care and
maintenance of the unit.
IMPORTANT
The enclosed message provides information neces-
sary for the protection of the unit.
DANGER
The safety alert symbol accompanied by the word
“DANGER” calls attention to an act or condition
which WILL lead to serious personal injury or
death if not avoided.
Throughout this manual and on the product itself, you will nd safety alerts and helpful, informational messages pre-
ceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to
you.
Improper use or maintenance can result in injury. Carefully read this manual. Learn how to operate your pump correctly.
Know and understand the location and operation of the controls. Also pay close attention to safety messages in this
manual.
IMPORTANT
Unauthorized modications to the pump may impair the function and/or safety and affect machine life. Use only ap-
proved accessories on the pump.
DANGER
Do not let anyone operate the pump without proper instruction, otherwise serious personal injury may result.
Do not pump ammable substances with this pump.
Do not pump corrosive chemicals with this pump. Exposure to chemicals can be hazardous.
• Keep people and pets out of the area where you are using the pump.
• Do not let children operate the pump, or handle hoses.
• Operation of a pump should be restricted to mature, properly instructed individuals.
Do not operate while under the inuence of alcohol or medication.
• Do not run engine in an enclosed or poorly ventilated area (inside a room, garage, barn, etc.). Exhaust gas contains
carbon monoxide, an odorless and deadly poisonous gas.
• Do not attempt to carry pump when engine is running.
• Do not operate pump on an incline. It should be placed on a rm, dry, level surface for proper engine operation and
lubrication. Keep the area free of any ammable material such as leaves, brush or fuels.
• Do not aim engine exhaust at materials that could catch re.
4
Symbol
description/application
Symbol form/shape
Symbol
description/application
Symbol form/shape
Hot
Surface
Carburetor adjustment
- Idle speed
Carburetor adjustment
- High speed mixture
Symbol
description/application
Symbol form/shape
Symbol
description/application
Symbol form/shape
"WARNING, SEE OP-
ERATOR' MANUAL
Wear eyes, ears and
head protection
Emergency stop
Fuel and oil mixture
Finger Severing
Carburetor adjustment
- Low speed mixture
InTernaTIonal symbols
Wear slip resis-
tant foot wear.
Choke Control
"Cold Start"
Position
(Choke Closed)
Choke Control
"Run"
Position
(Choke Open)
• Face cooling air intake (recoil start area) and mufer side of engine
3.3 ft. (1m) away from buildings, obstructions and other combustible
objects.
• Do not enclose unit, as it relies on free air circulation to cool the
engine. Enclosing the unit can create a re hazard resulting from
entrapped gas fumes and overheating which can result in damage to
the engine and other components.
• Avoid accidental res and engine overheating.
• Do not operate equipment when mentally or physically stressed.
• Do not, under any circumstances, use the pump for purposes that
exceed its rated capacity.
• Do not leave pump unattended. If not securely fastened, pump may
shift during operation.
TypICal pump applICaTIons
Draining Irrigation
Cellars Lawns
Basements Shrubs and Bushes
Flooded Areas Gardens
Sumps Transferring
Swimming Pools Water
WARNING
Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions are
not followed. Proper clothing and safety gear must be worn when operating unit.
personal CondITIon and safeTy equIpmenT
Water PumP
OPeratOr's manual
5
WARNING
Water can be a conductor of electric current when exposed to live
electrical wiring. Electrocution will result.
• Do not operate pump in ooded basements without rst shutting
off electricity from outside the house. Pump should be located
outside in a vented area.
• Do not operate pump in ooded areas near power lines unless
electric service has been disconnected.
Read the Manuals
• Provide all users of this equipment with the Operator’s Manual and
Safety Manual for instructions on Safe Operation.
Clear the Work Area
• Spectators and fellow workers must be warned, and children and
animals prevented from coming nearer than 15 m (50 ft.) while the
unit is in use.
Avoid Hot Surfaces
• Keep exhaust area clear of ammable debris. Avoid contact during
and immediately after operation.
WARNING
The ignition components of this machine generate an electromagnetic eld during operation which may interfere
with some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemakers should consult with
their physician and the pacemaker manufacturer before operating this machine. In the absence of such informa-
tion, ECHO does not recommend the use of ECHO products by anyone who has a pacemaker.
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Wear eye protection that meets ANSI Z87.1 or CE re-
quirements whenever you operate the unit.
Hand Protection
Wear no-slip, heavy-duty work gloves to improve your
grip on the handles. Gloves also reduce the transmission
of machine vibration to your hands.
Hearing Protection
ECHO recommends wearing hearing protection whenever
unit is used.
Proper Clothing
Wear snug tting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARVES, JEWELRY, or
clothing with loose or hanging items that could become
entangled in moving parts or surrounding growth..
Wear sturdy work shoes with nonskid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
Wear no-slip, heavy duty work gloves.
Keep long hair away from engine and air intake. Retain
hair with cap or net.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue
which may lead to heat stroke. Schedule heavy work for
early morning or late afternoon hours when temperatures
are cooler.
6
equIpmenT
Before operation a complete check of the unit must be performed;
• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.
• Inspect guards and shield for damage and ensure that they are securely in place. Replace if they are damaged or miss-
ing.
• Do not operate the pump without an air lter. Rapid engine wear will result.
• Ventilating openings such as crankcase ducts, engine cover, air lter and mufer exhaust outlet must be cleaned peri-
odically and kept free of debris to ensure proper operation and adequate cooling of the engine and pump.
WARNING
Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings.
• ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop
before removing obstructions, clearing debris, or servicing unit.
• DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.
• NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.
WARNING
Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or leaks are found,
do not use unit, otherwise serious personal injury or property damage may occur. Have unit repaired by an authorized
servicing dealer before using.
An Emission Control Label is located on the engine. (is
is an EXAMPLE ONLY, information on label varies by
engine FAMILY).
emIssIon ConTrol (eXhausT & evaporaTIve)
EPA 2010 and Later and/or C.A.R.B. TIER III
PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD)
e 50 or 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine
emissions output meets applicable emissions regulations, provided that approved maintenance procedures are fol-
lowed as listed in the Maintenance Section of this manual.
e emission control system for the engine is EM (engine
modication) and, if the second to last character of the Engine
Family on the Emission Control Information label (sample
below) is “C”, “K”, or “T”, the emission control system is EM
and TWC (3-way catalyst). e fuel tank/fuel line emission
control system is EVAP (evaporative emissions). Evaporative
emissions for California models are only applicable to fuel
tanks.
Water PumP
OPeratOr's manual
7
Hot Decal (near mufer)
Extra parts for
discharge hose
desCrIpTIon
Locate the safety decal on your unit. Make sure the decal is legible and that you understand and follow the instructions
on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instruc-
tions for specic information.
8
1. SPARK ARRESTOR MUFFLER OR SPARK ARRESTOR MUFFLER WITH CATALYST - The mufer or
catalytic mufer controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of
carbon from leaving the mufer. Keep exhaust area clear of ammable debris.
2. CARRYING HANDLE - The carrying handle is used to transport the pump.
3. SPARK PLUG - Provides spark to ignite fuel mixture.
4. CHOKE LEVER - Choke lever is located at the top of the air cleaner.
- Move choke forward to CLOSE (Starting Position) ( )
- Move to OPEN (Run Position) ( )
5. AIR CLEANER - Contains replaceable felt element. Should be inspected and cleaned as necessary or daily.
6. STARTER HANDLE - Pull handle slowly until starter engages then pull quickly and rmly. When engine starts,
return handle slowly. DO NOT let handle snap back or damage to unit can occur.
7. PRIMER BULB - Pumping primer bulb before starting engine draws fresh fuel from the fuel tank priming the
carburetor for starting. Pump primer bulb until fuel is visible and ows freely in the clear fuel tank return line. Pump
bulb an additional 4 or 5 times.
8. FUEL CAP - Covers and seals fuel tank. Securely tighten fuel cap after refueling.
9. IGNITION SWITCH - “Toggle Switch”mounted on engine. Move Toggle UP to Run. Move Toggle DOWN to
Stop.
10. PUMP STAND - Pump stand supports pump. Always place pump on a rm, level site as near to the water source as
possible. Make sure pump will not move due to vibration and/or the weight of suction hose when full of water.
11. PUMP HOUSING - Seals the water from air and has suction and discharge ports. The housing holds water after the
pump is stopped, eliminating the need for priming at the next start up.
12. DRAIN PLUG - Drains water from pump housing for storage.
13. SUCTION PORT - Suction hose attaches to port.
14. DISCHARGE PORT - Discharge hose attaches to port. Accepts 25 mm (1 inch) hose coupling or 25 x 19 mm
(1 x 3/4 inch) Garden Hose adaptor (included with pump).
15. PRIME PORT PLUG - Used to prime or ll the pump housing with water prior to initial start up. Pump is self
priming in subsequent operations. Never operate pump without water, otherwise pump seals will fail.
16. THROTTLE LEVER - Controls engine speed. Move lever towards engine for idle position. Move lever toward
pump housing for fast run position.
17. SEALING WASHER - Seals hose connector against pump port. Unit comes with two washers - one for suction
hose connector, one extra.*
18. HOSE FITTING - Unit comes with two ttings - one for suction hose - one extra.* When assembling, install clamp
onto hose, connecter onto hose, then press tting into hose.
19. HOSE CONNECTER - Connecter threads directly onto 1 inch pump ports. Unit comes with two connecters - one
for suction hose - one extra.*
20. HOSE CLAMP - Unit comes with three - one for clamping suction hose connecter tting - one for strainer - one
extra.*
21. SUCTION HOSE - 25 mm (1 inch) inner diameter, 3 m (10 ft.) length. Longer hose up to 7.5 m (24 ft.) can be at-
tached.
22. STRAINER - Strainer prevents foreign material larger than 5/16 inch diameter from entering and damaging the
pump. Always have strainer attached onto suction hose when operating the pump.
23. GARDEN HOSE ADAPTER - Adaptor steps down from 25 mm thread to 3/4 inch and allows household garden
hose to be utilized as discharge hose.
* Extrahosettingsareforusewith25mm(1inch)dischargehosewhichisnotsupplied.
Water PumP
OPeratOr's manual
9
____ 1 - Pump Assembly
____ 1 - Suction Hose (#21)
____ 1 - Operator's Manual
____ 1 - Emission Control Warranty Statement
____ 1 - Warranty Registration Card
____ 1 - Plastic Bag
____ 1, Garden Hose Adaptor (#23)
____ 3, Hose Clamps (#20)
____ 2, Hose Fittings (#18)
____ 2, Hose Connecter (#19)
____ 2, Sealing Washers (#17)
____ 1, Strainer (#22)
ConTenTs
Due to packaging restrictions, the ECHO product you have purchased requires some assembly.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing
parts. Use the contents list to check for missing parts.
assembly
suCTIon
hose
1. Remove vinyl cap from suction port (G).
2. Assemble suction hose (A) with clamp (B), hose connecter (C),
hose tting (D), and sealing washer (E) on one end and strainer
(F) with second clamp on the other end.
3. Attach hose to suction port (G).
NOTE
Longer 25 mm (1 inch) suction hose can be used up to a maximum
length of 7.5 m (24 feet).
IMPORTANT
• Make sure that all hose and pipe connections are air tight. An air
leak in the suction line or suction ttings may prevent priming
and will reduce the pumps capacity or efciency.
• Keep priming port plug and pump drain plug tightly secured in
place to prevent entry of air into the pump.
• Use an acceptable pipe thread sealant on all threaded nipple con-
nections.
IMPORTANT
Always use the strainer with the suction hose. Gravel or debris
sucked into the pump will cause serious impeller and housing dam-
age.
If the strainer clogs with debris, prevent the strainer from touching
the bottom. Placing the strainer in a submerged bucket or basket
may also work.
A
B
D
C
E
F
G
B
10
H
B
D
C
E
E
dIsCharge hose
Garden Hose
NOTE
Garden hose ranging from 13 mm (1/2 inch) to 19 mm (3/4 inch) in
diameter can be used on the discharge end of this pump.
1. Remove vinyl cap from pump discharge port.
2. Attach the 25 mm to 3/4 inch adaptor (H) and washer (E) tightly
onto pump discharge port.
3. Attach garden hose onto adaptor (H).
1 inch discharge hose
NOTE
Rubber or fabric hose may be used. Hose can be obtained from
local contractor supply companies. Extra ttings are included with
the pump.
1. Assemble clamp (B), hose connecter (C), hose tting (D) and seal-
ing washer (E) as shown for suction hose.
2. Attach hose onto discharge port. When 1 inch discharge hose is
used, 25 mm to 3/4 inch adaptor (H) is not required.
Water PumP
OPeratOr's manual
11
NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor
performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage
section of this manual.
WARNING
Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are
NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance prob-
lems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to,
improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carbu-
retors and other engine components.
Fuel Requirements
Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to
10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol)
is NOT approved.
Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O.FD Standards must be
used. Echo brand premium Power Blend X
TM
Universal 2-Stroke Oil meets these standards. Engine problems due to
inadequate lubrication caused by failure to use an (ISO/CD 13738) and J.A.S.O. FD certied oil, such as Echo premium
Power Blend X
TM
, will void the two-stroke engine warranty.
IMPORTANT
Echo premium Power Blend X
TM
Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo en-
gines sold in the past regardless of ratio specied in those manuals.
operaTIon
WARNING
Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop
before removing obstructions, clearing debris, or servicing unit.
WARNING
Operation of this equipment may create sparks that can start res. is unit is equipped with a spark arrestor to
prevent discharge of hot particles from the engine. Metal blade use also can create sparks if the blade strikes rocks,
metal, or other hard objects. Contact local re authorities for laws or regulations regarding re prevention require-
ments.
WARNING
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconscious-
ness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed
away from your face and body.
fuel
12
Mixing Instructions
1. Fill an approved fuel container with half of the required amount of
gasoline.
2. Add the proper amount of 2-stroke oil to gasoline.
3. Close container and shake to mix oil with gasoline.
4. Add remaining gasoline, close fuel container, and remix.
IMPORTANT
Spilled fuel is a leading cause of hydrocarbon emissions. Some
states may require the use of automatic fuel shut-off containers to
reduce fuel spillage.
After use
• DO NOT store a unit with fuel in its tank. Leaks can occur. Return
unused fuel to an approved fuel storage container.
Storage - Fuel storage laws vary by locality. Contact your local gov-
ernment for the laws affecting your area. As a precaution, store fuel in
an approved, airtight container. Store in a well-ventilated, unoccupied
building, away from sparks and ames.
IMPORTANT
Stored fuel ages. Do not mix more fuel than you expect to use in
thirty (30) days, ninety (90) days when a fuel stabilizer is added.
IMPORTANT
Stored two-stroke fuel may separate. ALWAYS shake fuel con-
tainer thoroughly before each use.
Handling Fuel
DANGER
Fuel is VERY ammable. Use extreme care when mixing, storing or handling or serious personal injury may result.
• Use an approved fuel container.
• DO NOT smoke near fuel.
• DO NOT allow ames or sparks near fuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.
• NEVER refuel a unit when the engine is HOT or RUNNING!
• DO NOT ll fuel tanks indoors. ALWAYS ll fuel tanks outdoors over bare ground.
• DO NOT overll fuel tank. Wipe up spills immediately.
• Securely tighten fuel tank cap and close fuel container after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.
• Move at least 3m (10 ft.) from refueling location before starting the engine.
Water PumP
OPeratOr's manual
13
1. Select a rm, level site as near the water source as possible. Never
exceed a suction lift (A) of 7.5 m (24 feet) or water will not ow.
Make sure pump will not move due to vibration and/or the pull
from the weight of suction hose when full of water.
2. Total vertical discharge (B)is the distance the pump is capable of
lifting water from the surface of the water to the discharge hose
end. The distance must not exceed 29 m (95 ft.), otherwise no
water will ow.
3. Make sure all hoses and pipe connections are air tight, and all hose
coupling gaskets or o-rings are installed.
4. Keep prime port plug and pump drain plug tightly secured in place
during operation.
5. Make sure strainer is in place.
6. Maximum pump efciency is obtained by:
• Keeping hoses straight and avoiding kinks and sharp bends in
hoses.
• Using shortest suction lift practical.
• Using as few connecters, elbows and adaptors as possible.
• Keeping the pump and associated equipment in good operating
condition.
prImIng The pump
1. All ECHO pumps are self-priming centrifugal pumps. Only a
single priming operation at the beginning is needed to allow the
pump to be used continuously or intermittently.
2. Remove prime port plug (A) and ll pump housing with water.
3. Replace prime port plug securely, making sure the gasket is on and
in good condition.
With suction intake and strainer in the water to be pumped, start the
engine. (See Starting the Engine.)
IMPORTANT
When priming the pump, operate the engine at half throttle.
Should the engine be operated at full throttle during initial prime,
water surges alternately followed by air pockets will cause over-
speeding, resulting in possible engine damage.
NOTE
With engine running at approximately half throttle, the priming
time depends upon the length of suction hose. Priming time can
be as short as 30 seconds when lift is less than 1.5 m (5 feet) or as
long as 5-7 minutes when pump is some distance from the water
and using maximum lift of 7.5 m (24 feet) at sea level.
A
14
A
B
C
D
E
WARNING
Water can be conductor of electric current when exposed to live
electrical wiring. Electrocution will result.
• Do not operate pump in ooded basements without rst shutting
off electricity from outside the house. Pump should be located
outside in a vented area.
• Do not operate pump in ooded areas near power lines unless
electric service has been disconnected.
IMPORTANT
• Prolonged pumping of water containing sludge mud and gravel
will cause rapid wear to impeller or internal pump parts. Pump
only clear water.
• Pump suction lift is affected by water temperatures. Maximum
temperature of water should be 60
o
C (140
o
F), or lower.
• Internal pump body components will corrode if the pump is used
to pump liquids high in acidity or alkaline.
sTarTIng Cold engIne
WARNING
Do not run engine in an enclosed area. Exhaust gas contains carbon
monoxide, an odorless and deadly poison.
IMPORTANT
Do not start or run the pump without priming the pump with wa-
ter. Serious damage to the pump seals will occur when the pump is
run dry.
1. Place suction intake and strainer in the water to be pumped prior to
starting engine.
2. Place ignition switch (A) in Start/Run position.
3. Move choke (B) to Cold Start ( ) Position.
4. Pump primer bulb (C) until fuel is visible and ows freely in the
clear fuel tank return line. Pump bulb an additional 4 or 5 times.
5. Move throttle lever (D) towards engine to idle position.
6. Pull starter handle (E) until engine res (5 ~ 6 pulls maximum).
7. After engine res (or 5 ~ 6 pulls), move choke lever (B) to Run
( ) position and pull recoil starter handle/rope until engine
starts and runs. Allow unit to warm up at idle for several minutes.
NOTE
If engine does not start with choke in “Run” position after 5 pulls,
repeat instructions.
8. Place throttle lever (D) in half throttle position until pump begins
to pump water. Then move lever to full throttle.
Water PumP
OPeratOr's manual
15
sTarTIng warm engIne
The starting procedure is the same as Cold Start except DO NOT close
the choke.
1. Move ignition switch (A) to start, move throttle lever (D) towards
engine to idle position. Pull starter handle (E) and engine should
start. Do not use choke (B).
NOTE
If engine does not start after 5 pulls, use Cold Start Procedure.
sToppIng engIne
1. Move throttle lever (D) towards engine to idle position and allow
engine to return to idle before shutting engine off.
2. Move ignition switch (A) to “Stop” position.
WARNING
If engine does not stop when stop switch is moved to STOP posi-
tion, close choke - COLD START position - to stall engine. Have
your ECHO dealer repair stop switch before using unit again.
A
B
C
E
A
D
A
B
Cold weaTher operaTIon
Pumps will not freeze when running. However, in freezing weather, re-
move drain plug (A) and prime port plug (B) and drain the water from
pump completely after use. All hoses exposed to freezing temperatures
should also be drained, Before restarting the pump, replace the drain
plug and ll plug securely, making sure the gaskets are in place and in
good condition to prevent air entry into the pump. Prime the pump.
16
Your ECHO water pump is designed to provide many hours of trouble free service. Regular scheduled maintenance will
help your water pump achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want
to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOUR-
SELF or have the ECHO Dealer do it, each maintenance task has been graded.
skIll levels
Level 1 = Easy to do. Most required tools come with unit.
Level 2 = Moderate difculty. Some specialized tools may be required.
ECHO offers REPOWER Maintenance Kits and Parts to make your maintenance job easier. Just below each task head-
ing are listed the various part numbers required for that task. See your ECHO dealer for these parts.
maInTenaCe InTervals
WARNING
Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop
before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear
gloves to protect hands from sharp edges and hot surfaces.
maInTenanCe
COMPONENT/
SYSTEM
MAINTENANCE
PROCEDURE
REQ'D SKILL
LEVEL
DAILY OR
BEFORE USE
EVERY
REFUEL
3 MONTHS
OR 90
HOURS
YEARLY 600
HOURS
Air Filter Inspect/Clean 1
I / C *
Choke Shutter Inspect/Clean 1
I / C
Fuel Filter Inspect 1
I *
I / R *
Fuel Cap Gasket Inspect/Replace 1
I * R *
Fuel System Inspect/Replace 1
I * I *
Spark Plug Inspect/Clean 1
I / C / R *
Cooling System Inspect/Clean 2
I / C
Muffler Spark Arrestor Inspect/Clean/Replace 2
I / C / R *
Cylinder Exhaust Port Inspect/Clean/Decarbon 2
I / C
Recoil Starter Rope Inspect/Clean 1
I / C *
Screws/Nuts/Bolts Inspect/Tighten/Replace 1
I *
MAINTENANCE PROCEDURE LETTER CODES:
I = INSPECT, R = REPLACE, C = CLEAN
IMPORTANT NOTE
- Time intervals shown are maximum. Actual use and your experience will determine the frequency of
required maintenance.
MAINTENANCE PROCEDURE NOTES:
* Replacement is recommended based on the finding of damage or wear during inspection.
Water PumP
OPeratOr's manual
17
aIr fIlTer
Level 1.
Parts required: REPOWER AIR & FUEL FILTER KIT.
1. Close choke (Cold Start Position [ ]). This prevents dirt from
entering the carburetor throat when the air lter is removed. Brush
accumulated dirt from air cleaner area.
2. Remove air lter cover. Brush dirt from inside cover.
3. Remove air lter and lightly brush debris from lter. Replace lter
if it is damaged, fuel soaked, very dirty, or the rubber sealing edges
are deformed.
4. If lter can be reused, be certain it:
• Fits tightly in the air lter cavity.
• Is installed with the original side out.
5. Install air lter cover.
NOTE
Carburetor adjustment may be needed after air lter cleaning/re-
placement. See Carburetor Adjustment Section.
fuel fIlTer
Level 1.
Parts required: REPOWER AIR & FUEL FILTER KIT.
DANGER
Fuel is VERY ammable. Use extreme care when mixing, storing
or handling.
1. Use a clean rag to remove loose dirt from around fuel cap and
empty fuel tank.
2. Use the “fuel line hook” to pull the fuel line and lter from the
tank.
3. Remove the lter from the line and install the new lter.
NOTE
Federal EPA regulations require all model year 2012 and later gasoline powered engines produced for sale in the
United States to be equipped with a special low permeation fuel supply hose between the carburetor and fuel tank.
When servicing model year 2012 and later equipment, only fuel supply hoses certied by EPA can be used to replace
the original equipment supply hose. Fines up to $37,500 may be enforced for using an un-certied replacement part.
18
CoolIng sysTem
Level 2.
Parts Required: None.
IMPORTANT
To maintain proper engine operating temperatures, cooling air must
pass freely through the cylinder n area. This ow of air carries
combustion heat away from the engine.
Overheating and engine seizure can occur when:
• Air intakes are blocked, preventing cooling air from reaching the
cylinder.
• Dust and grass build up on the outside of the cylinder. This build
up insulates the engine and prevents the heat from leaving.
Removal of cooling passage blockages or cleaning of cooling ns is
considered “Normal Maintenance”. Any failure attributed to lack of
maintenance is not warranted.
1. Remove spark plug lead and throttle cable end from the carburetor
swivel.
2. Remove the four screws that retain the engine cover. Two at the top
of the starter, two on either side of the front. Lift the cover from the
engine and lay to the front of the pump.
spark plug
Level 2.
Parts Required: REPOWER
TM
Tune-Up Kit
1. Remove spark plug and check for fouling, worn and rounded cen-
ter electrode.
2. Clean the plug or replace with a new one. DO NOT sand blast to
clean. Remaining sand will damage engine.
3. Adjust spark plug gap by bending outer electrode.
4. Tighten spark plug to 150-170 kgf • cm (130-150 in • lbf).
0.65 mm
(0.026 in.)
Water PumP
OPeratOr's manual
19
NOTE
The throttle cable remains assembled to the engine cover and the
spark plug lead and grommet remain installed.
IMPORTANT
DO NOT use a metal scraper to remove dirt from the cylinder ns.
3. Use the brush to remove dirt from the cylinder ns.
4. Remove grass and leaves from the grid between the starter and fuel
tank.
5. When installing the cover, be certain the tab of the metal deector
shield is in the slot of the cover.
eXhausT sysTem
Spark Arrestor Screen
Level2.
Parts Required: Spark Arrestor Screen, Gasket
1. Remove engine cover. See “Cleaning Cooling System” for step by
step instructions.
2. Place piston at Top Dead Center (TDC) to prevent carbon/dirt from
entering cylinder.
3. Remove screen cover (A), screen holder (B), gasket (C), and spark
arrestor screen (D) from mufer body.
4. Clean carbon deposits from screen (D) and mufer components.
5. Replace screen if it is cracked, plugged or has holes burned
through.
6. Install spark arrestor screen, gaskets, and cover.
A
B
C
D
20
Exhaust Port Cleaning
Level2.
Parts Required: As needed: Heat Shield
1. Remove engine cover. See “Cleaning Cooling System” for step by
step instructions..
2. Place piston at top dead center. Remove mufer (A) and heat
shield (B).
3. Use a wood or plastic scraping tool to clean deposits from cylinder
exhaust port.
IMPORTANT
Never use a metal tool to scrape carbon from the exhaust port.
Do not scratch the cylinder or piston when cleaning the exhaust
port. Do not allow carbon particles to enter the cylinder.
4. Inspect heat shield, and replace if damaged.
5. Install heat shield and mufer.
6. Tighten mufer mounting bolts (or nuts) to 50-55 in•lbf
(55-65 kgf•cm).
7. Install engine cover and attach spark plug lead and throttle cable.
8. Start engine, and warm to operating temperature.
9. Stop engine, and re-tighten mounting bolts (or nuts) to specica-
tions.
A
B
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
red lion Engine-Driven Aluminum TRANSFER Pump Operating instructions
-
Stark 72022 User manual
-
Shindaiwa GP344 User manual
-
Generac 6918 User guide
-
-
Maruyama MP2533E2 Owner's manual
-
Homelite ut40530 Owner's manual
-
Generac 6821 User guide
-
-
Ford FPX30E User manual