Behringer EURORACK UB1202 User manual

EURORACK UB1202
Behringer
Brand
Behringer
Model
EURORACK UB1202
Category
Audio mixers
Type
User manual

This manual is also suitable for

EURORACK UB502/UB802/UB1002/UB1202
User Manual
A50-18013-00005
EURORACK UB502/UB802/UB1002/UB1202
2
Important Safety Instructions
This symbol, wherever it appears, alerts you to the
*
presence of uninsulated dangerous voltage inside the
enclosure - voltage that may be sufcient to constitute
a risk of shock.
This symbol, wherever it appears, alerts you to important
!
operating and maintenance instructions in the accom-
panying literature. Please read the manual.
Caution
To reduce the risk of electric shock, do not remove the +
top cover (or the rear section). No user serviceable parts
inside. Refer servicing to qualied personnel.
Caution
To reduce the risk of re or electric shock, do not expose +
this appliance to rain and moisture. The apparatus shall
not be exposed to dripping or splashing liquids and no
objects lled with liquids, such as vases, shall be placed
on the apparatus.
Caution
These service instructions are for use by qualied ser- +
vice personnel only. To reduce the risk of electric shock
do not perform any servicing other than that contained in
the operation instructions. Repairs have to be performed
by qualied service personnel.
Read these instructions.1)
Keep these instructions.2)
Heed all warnings.3)
Follow all instructions.4)
Do not use this apparatus near water.5)
Clean only with dry cloth.6)
Do not block any ventilation openings. Install in accor-7)
dance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, 8)
heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
Do not defeat the safety purpose of the polarized or 9)
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided
plug does not t into your outlet, consult an electrician
for replacement of the obsolete outlet.
Place the power cord so that it is protected from being 10)
walked on and sharp edges. Be sure that the power cord is
protected particularly at plugs, convenience receptacles
and the point where it exits from the apparatus.
The apparatus shall be connected to a MAINS socket 11)
outlet with a protective earthing connection.
Where the MAINS plug or an appliance coupler is used 12)
as the disconnect device, the disconnect device shall
remain readily operable.
Use only attachments/accessories specified by the 13)
manufacturer.
Use only with the cart, stand, tripod, bracket, or table 14)
specied by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when 15)
unused for long periods of time.
Refer all servicing to qualified service personnel. 16)
Servicing is required when the apparatus has been dam-
aged in any way, such as power supply cord or plug is
damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been
dropped.
EURORACK UB502/UB802/UB1002/UB1202
3
Forword
Dear Customer,
I’m sure you’re one of
those people who have
devoted themselves body
and soul to your chosen
area and no doubt this has
transformed you into an
expert in your eld!
Well, for over 30 years, my
passion has been music
and electronics. This not
only led me to establish
BEHRINGER, but also
enabled me to convey and
share my enthusiasm with
my employees.
During all the years I’ve
been involved with studio
technology and end users,
I have developed a feel for
the things that really count, such as sound quality, reliability and
ease of use. What’s more, I have always had the desire to push
the boundaries of technical possibilities to the extreme.
It was precisely this motivation that prompted me to start work
on a new series of mixing consoles. Since our EURORACKs had
already set new standards world-wide, I knew the development
objectives behind the products bearing my initials had to be es-
pecially ambitious.
Thus, the concept and design of the new UB mixing consoles
bear my signature. The design work, the entire circuit diagram
and PCB development, and even the mechanical concepts are
my own work. I carefully selected each individual component—
with the aim of pushing the mixing consoles’ analog and digital
technologies to their limits.
My vision was to enable you, the user, to give free rein to your
true potential and creativity. The result is incredibly powerful
mixing consoles that offer intuitive operation. They cannot fail
to impress with their extremely exible routing possibilities plus
fantastic wealth of functions. Innovative technologies, such as the
completely new IMP “Invisible” Mic Preamps, guarantee optimum
sound quality. And extraordinarily high-quality components provide
unrivalled reliability, even under extreme loads.
Your new UB mixing console is of high quality yet is simple to use;
you’ll soon appreciate that I, both personally and in my capacity
as musician and sound engineer, put you, the end user, rst and
that these products were only possible because of the passion
and the attention to detail that went into them.
Thank you for the condence you have placed in us by purchasing
the UB mixing console. I should also like to thank all those who,
with their personal commitment and passion, have helped me
realize this impressive series of mixing consoles.
Uli Behringer
Table of contents
1. Introduction ......................................................................... 4
1.1 General mixing console functions ................................ 4
1.2 The user’s manual ........................................................ 4
1.3 Before you get started .................................................. 4
1.3.1 Shipment ............................................................. 4
1.3.2 Initial operation ................................................... 4
1.3.3 Online Registration ............................................. 4
2. Control elements and connectors .................................... 4
2.1 Mono channels ............................................................. 5
2.1.1 Microphone and line inputs ................................. 5
2.1.2 Equalizer ............................................................. 5
2.1.3 FX sends, panorama and level adjustment ........ 5
2.2 Stereo channels ........................................................... 5
2.2.1 Stereo line inputs ................................................ 5
2.2.2 Equalizer stereo channels (UB802) .................... 5
2.2.3 FX sends, balance and level adjustment ............ 6
2.3 Connector panel and main section............................... 6
2.3.1 Send/return effects path ..................................... 6
2.3.2 Monitor and main mix ......................................... 6
2.3.3 Tape connectors ................................................. 7
2.3.4 Signal assignment .............................................. 7
2.3.5 Phantom power and LED displays ...................... 7
3. Installation........................................................................... 7
3.1 Mains connection ......................................................... 7
3.2 Audio connections ........................................................ 8
4. Specications ..................................................................... 9
5. Warranty ........................................................................... 10
EURORACK UB502/UB802/UB1002/UB1202
Control elements and connectors4
Introduction1.
Congratulations! In purchasing our EURORACK UB502/UB802/
UB1002/UB1202 you have acquired a mixing console whose small
size belies its incredible versatility and audio performance.
The range of inputs and outputs comprises microphone inputs (with
+48 V phantom power supply), line inputs, possibilities for con-
necting effects devices, connectors for a 2-track master machine
(e.g. DAT recorder) and a monitor system consisting of monitor
loudspeaker(s) and power amplier (except for UB502).
IMP “Invisible” Mic Preamp
The microphone channels are tted with BEHRINGER’s brand
new premium quality IMP invisible mic preamps that boast the
following features:
130 dB dynamic range for an incredible amount of =
headroom
A bandwidth ranging from below 10 Hz to over 200 kHz for =
crystal-clear reproduction of even the nest nuances
The extremely low-noise and distortionfree circuitry guaran- =
tees absolutely natural and transparent signal reproduction
hey are perfectly matched to every conceivable microphone =
with up to 60 dB gain and +48 volt phantom power supply
They enable full utilisation of the greatly extended dynamic =
range of your 24-bit/192 kHz HD recorder, thereby maintaining
optimal audio quality
CAUTION!
We should like to draw your attention to the fact that +
extreme volumes may damage your hearing and/or
your headphones or loudspeakers. Turn the MAIN MIX
control and PHONES control in the main section fully
counter-clockwise before you switch on the unit. Always
be careful to set appropriate volume levels.
Important notes concerning installation
The sound quality may diminish within the range of pow- +
erful broadcasting stations and high-frequency sources.
Increase the distance between the transmitter and the
device and use shielded cables for all connections.
General mixing console functions1.1
A mixing console fulls three main functions:
= Signal processing: Preamplication, level adjustment,
mixing of effects, frequency equalization.
= Signal distribution: Summing of signals to the aux sends
for effects processing and monitor mix, distribution to
one or several recording tracks, power amp(s), control
room and 2-track outputs.
= Mix: Setting the volume level, frequency distribution and
positioning of the individual signals in the stereo eld,
level control of the total mix to match the recording de-
vices/crossover/power amplier(s). All other mixer func-
tions can be included in this main function.
The interface of BEHRINGER mixing consoles is optimized for
these tasks enabling you to easily keep track of the signal path.
The user’s manual1.2
The user’s manual is designed to give you both an overview of
the controls, as well as detailed information on how to use them.
In order to help you understand the links between the controls,
we have arranged them in groups according to their function. The
illustrations at the beginning of each chapter show the controls
described in each respective chapter.
The block diagram supplied with the mixing console +
gives you an overview of the connections between the
inputs and outputs, as well as the associated switches
and controls.
For the moment, just try and trace the signal path from the mi-
crophone input to the FX send connector. Don’t be put off by the
huge range of possibilities; it’s easier than you think! If you look
at the overview of the controls at the same time, you’ll be able
to quickly familiarize yourself with your mixing console and you’ll
soon be making the most of all its many possibilities.
If you need to know more about specic issues, please visit our
website at http://www.behringer.com, where you’ll nd explanations
of (for example) effects and dynamics applications.
Before you get started1.3
Shipment1.3.1
Your mixing console was carefully packed in the factory to guaran-
tee safe transport. Nevertheless, we recommend that you carefully
examine the packaging and its contents for any signs of physical
damage, which may have occurred during transit.
If the unit is damaged, please do NOT return it to us, +
but notify your dealer and the shipping company im-
mediately, otherwise claims for damage or replacement
may not be granted.
Initial operation1.3.2
Be sure that there is enough space around the unit for cooling
purposes and to avoid over-heating please do not place your
mixing console on high-temperature devices such as radiators
or power amps. The console is connected to the mains via the
supplied cable. The console meets the required safety standards.
Blown fuses must only be replaced by fuses of the same type
and rating.
Never connect the EURORACK to the power supply unit +
when the latter is connected to the mains! First connect
the power supply unit to the console, then connect the
power supply unit to the mains.
Please note that all units must be properly grounded. For +
your own safety, you should never remove any ground
connectors from electrical devices or power cables, or
render them inoperative.
Please ensure that only qualied people install and +
operate the mixing console. During installation and op-
eration, the user must have sufcient electrical contact
to earth, otherwise electrostatic discharges might affect
the operation of the unit.
Online Registration1.3.3
Please register your new BEHRINGER equipment right after your
purchase by visiting http://www.behringer.com and read the terms
and conditions of our warranty carefully.
Should your BEHRINGER product malfunction, it is our inten-
tion to have it repaired as quickly as possible. To arrange for
warranty service, please contact the BEHRINGER retailer from
whom the equipment was purchased. Should your BEHRINGER
dealer not be located in your vicinity, you may directly contact
one of our subsidiaries. Corresponding contact information is
included in the original equipment packaging (Global Contact
Information/European Contact Information). Should your country
not be listed, please contact the distributor nearest you. A list
of distributors can be found in the support area of our website
(http://www.behringer.com).
Registering your purchase and equipment with us helps us process
your repair claims more quickly and efciently.
Thank you for your cooperation!
Control elements and connectors2.
This chapter describes the various control elements of your mixing
console. All controls, switches and connectors will be discussed
in detail.
EURORACK UB502/UB802/UB1002/UB1202
Control elements and connectors 5
Mono channels2.1
Microphone and line inputs2.1.1
Connectors and controls of mic/line inputsFig. 2.1:
MIC
Each mono input channel offers a balanced microphone input via
the XLR connector and also features a switchable +48V phantom
power supply for condenser microphones.
Please mute your playback system before you activate +
the phantom power supply to prevent switch-on thumps
being directed to your loudspeakers. Please also note
the instructions in chapter 2.3.5 “Phantom power and
LED displays”.
LINE IN
Each mono input also features a balanced line input on a 1/4"
connector. Unbalanced devices (mono jacks) can also be con-
nected to these inputs.
Please remember that you can only use either the mi- +
crophone or the line input of a channel at any one time.
You can never use both simultaneously!
GAIN
Use the GAIN control to adjust the input gain. This control should
always be turned fully counterclockwise whenever you connect
or disconnect a signal source to one of the inputs.
Equalizer2.1.2
All mono input channels include a 3-band equalizer, except for the
UB502, which is equipped with a 2-band EQ. All bands provide
boost or cut of up to 15 dB. In the central position, the equalizer
is inactive.
The equalizer of the mono input channelsFig. 2.2:
EQ
The upper (HI) and the lower band (LO) are shelving lters that
increase or decrease all frequencies above or below their cut-off
frequency. The cut-off frequencies of the upper and lower band are
12 kHz and 80 Hz respectively. The mid band (UB802/UB1002/
UB1202) is congured as a peak lter with a center frequency
of 2.5 kHz.
LOW CUT
In addition, the mono channels (UB1002 and UB1202) are
equipped with a steep LO CUT lter (slope at 18 dB/oct., -3 dB
at 75 Hz) designed to eliminate unwanted low-frequency signal
components.
FX sends, panorama and level adjustment2.1.3
The FX send/panorama/level controlsFig. 2.3:
FX (UB802/UB1002/UB1202 only)
FX sends (or AUX sends) enable you to feed signals via a variable
control from one or more channels and sum these signals to a
bus. The bus appears at the console’s FX send output and can
be fed from there to an external effects device. The return from
the effects unit is then brought back into the console on the aux
return connectors (UB802) or normal channel inputs. Each FX
send is mono and features up to +15 dB gain.
As the name suggests, the FX sends of the EURORACK mixing
consoles are intended to drive effects devices (reverb, delay, etc)
and are therefore congured post-fader. This means that the mix
between dry signal and effect remains at the level determined by
the channel’s aux send, irrespective of the channel fader setting.
If this were not the case, the effects signal of the channel would
remain audible even when the fader is lowered to zero.
PAN
The PAN control determines the position of the channel signal
within the stereo image. This control features a constant-power
characteristic, which means the signal is always maintained at a
constant level, irrespective of position in the stereo panorama.
LEVEL
The LEVEL control determines the level of the channel signal in
the main mix.
PEAK
The PEAK LED’s of the mono channels illuminate when the input
signal is driven too high, which could cause distortion. If this hap-
pens, use the GAIN control to reduce the preamp level until the
LED does not light anymore.
Stereo channels2.2
Stereo line inputs2.2.1
Stereo line inputsFig. 2.4:
LINE IN
Each stereo channel has two balanced line level inputs on 1/4"
jacks for left and right channels. If only the jack marked “L” (left)
is used, the channel operates in mono. The stereo channels are
designed to handle typical line level signals.
Both inputs will also accept unbalanced jacks.
Equalizer stereo channels (UB802)2.2.2
The EURORACK UB802 features a stereo 3-band EQ in each
stereo channel. The lter characteristics and cut-off frequencies
are the same as those in the mono channels.
EURORACK UB502/UB802/UB1002/UB1202
Control elements and connectors6
The equalizer of the stereo input channelsFig. 2.5:
A stereo EQ is highly preferable to two mono equalizers. when
working on a stereo signal, as two separate EQ’s will usually
produce an unwanted discrepancy between the left and right
channels.
FX sends, balance and level adjustment2.2.3
The FX send/balance/level controlsFig. 2.6:
FX
The FX sends of the stereo channels function similar to those of
the mono channels. However, since the FX send buses are both
mono, a mono sum is rst taken from the stereo input before it is
sent to the FX bus. The UB502 is not equipped with FXsends.
BAL
The BAL(ANCE) control determines the levels of left and right input
signals relative to each other before both signals are then routed
to the main stereo mix bus. If a channel is operated in mono via
the left line input, this control has the same function as the PAN
control used in the mono channels.
LEVEL
The LEVEL control determines the volume of the channel being
sent to the main mix.
+4/-10
The stereo inputs of the EURORACK UB1002 and UB1202 have
an input sensitivity switch which selects between +4 dBu and -10
dBV. At -10 dBV (home-recording level), the input is more sensitive
(requires less level to drive it) than at +4 dBu (studio level).
Connector panel and main section2.3
Send/return effects path2.3.1
FX send/return connectorsFig. 2.7:
FX send/return controlsFig. 2.8:
STEREO AUX RETURN
UB802 only: the STEREO AUX RETURN connectors are used
to bring the output of the external effects device (whose input is
derived from the aux sends) back into the console. You can instead
use these connectors as additional inputs, but any effects device
will then have to be brought back into the console via a normal
stereo channel. This does, however, give you the ability to use the
channel EQ on the effects return signal if you wish.
When using a stereo channel as effects return path, the +
FX control of the relevant channel should generally be
turned fully down to avoid undesirable feedback.
If only the left connector is used, the AUX RETURN automatically
operates in mono. Use the AUX RET(URN) control to determine
how much of the effects signal is sent to the main mix.
FX SEND
The FX SEND output (does not apply for UB502) should be con-
nected to the input of an external effects unit. The post-fader FX
signal you created using the input channel FX controls is sent to
the effects unit via the FX SEND ouput. Use the FX SEND control
of the main section to adjust the overall send level (UB1002 and
UB1202 only).
Monitor and main mix2.3.2
Monitor/main mix connectorsFig. 2.9:
Monitor control and main mix faderFig. 2.10:
PHONES/CONTROL ROOM
The stereo PHONES jack (at the top of the connector panel) is
where you connect headphones. The unbalanced CONTROL
ROOM OUT jacks carry the summed effects and main mix sig-
nals, as well as soloed channel signals. The PHONES/CONTROL
ROOM control adjusts the level of both headphones and main
monitor outputs. The UB502 is not equipped with control room
outputs.
EURORACK UB502/UB802/UB1002/UB1202
Installation 7
MAIN MIX
The MAIN OUT connectors are unbalanced mono jacks. The main
mix signal appears here at a level of 0 dBu. The MAIN MIX fader
adjusts the volume of these outputs. The EURORACK UB802 and
UB502 mixing consoles feature a rotary control for this purpose.
Tape connectors2.3.3
TAPE INPUT
The TAPE INPUTs are used to bring an external signal source
(e.g. CD player, tape deck, etc.) into the console. They can also
be used as a standard stereo line input, so the output of a second
EURORACK or BEHRINGER ULTRALINK PRO MX882 can be
connected.
Tape input/outputFig. 2.11:
Alternatively the line or tape output of a hi- amplier with source
selection switch could also be hooked up here, allowing you to
easily listen to additional sources.
TAPE OUTPUT
These connectors are wired in parallel with the MAIN OUT and
carry the main mix signal (unbalanced). Connect the TAPE
OUTPUT to the inputs of your recording device. The output level
is adjusted via the high-precision MAIN MIX fader or rotary control
(UB802).
Signal assignment2.3.4
Assignment switches of the main sectionFig. 2.12:
TAPE TO MIX
When the TAPE TO MIX switch is depressed, the 2-track input
is assigned to the main mix providing an additional input for tape
machines, MIDI instruments or other signal sources that do not
require any processing.
TAPE TO CTRL ROOM (502: TAPE TO PHONES)
Press the TAPE TO CTRL ROOM/PHONES switch if you want to
monitor the 2-track input via the CTRL ROOM OUT. This provides
an easy way to monitor signals coming back from tape to ensure
that they are recording correctly.
If you are recording a signal via the TAPE OUTPUT +
and wish to listen to this simultaneously via the TAPE
INPUT, do not use the TAPE TO MIX switch. Doing this
would create a feedback loop, since the signal would
be routed, via the main mix, back to tape via the TAPE
OUTPUT. To monitor the TAPE INPUT, use the TAPE
TO CTRL ROOM switch to assign the tape signal to the
monitor(s) or headphones. This will avoid the tape signal
being routed to the TAPE OUTPUT.
FX TO CTRL ROOM
If you want to monitor only the FX send signal in your headphones
or monitor speaker(s), press the FX TO CTRL R switch. This
mutes the main mix signal while routing the FX SEND output
to the monitor(s). The EURORACK UB802 and UB502 do not
feature this switch.
Phantom power and LED displays2.3.5
Phantom power and control LEDsFig. 2.13:
+48 V
The red +48 V LED lights up when phantom power is on. The
PHANTOM switch activates the phantom power supply on the
XLR connectors of all mono channels.
Please do not connect microphones to the mixer (or the +
stagebox/wallbox) as long as the phantom power supply
is switched on. Connect the micro-phones before you
switch on the power supply. In addition, the monitor/PA
loudspeakers should be muted before you activate the
phantom power supply. After switching on, wait approx.
one minute in order to allow system stabilization.
POWER
The blue POWER LED indicates that the console is powered
on.
Level indicator
The high-precision 4-segment display accurately displays the
relevant signal level.
LEVEL SETTING: To correctly set the gains of the channels, rst
set the LEVEL controls of the input channels to their center posi-
tions (0 dB). Then use the GAIN controls to increase the input
amplication until signal peaks show 0 dB on the level meter.
When recording to digital recorders, the recorder’s peak meter
should not go into overload. While analog recorders can be
overloaded to some extent, creating only a certain amount of
distortion (which is common and often desirable), digital recorders
distort quickly when overloaded. In addition, digital distortion is
not only undesirable, but also renders your recording completely
useless.
The peak meters of your EURORACK display the level +
virtually independent of frequency. A recording level of
0 dB is recommended for all signal types.
Installation3.
Mains connection3.1
AC POWER IN
Connect the power supply to the 3-pin mains connector on the
rear of the console. Use the AC adapter supplied to connect the
console to the mains. The adapter complies with all applicable
safety standards.
Please use only the power supply unit provided with +
the console.
Never connect the EURORACK to the power supply unit +
while the latter is connected to the mains! First connect
the console to the power supply unit, then connect the
power supply unit to the mains.
Please note that both the power supply unit and the +
mixing console heat up considerably during operation.
This is completely normal.
EURORACK UB502/UB802/UB1002/UB1202
Installation8
Audio connections3.2
You will need a large number of cables for different applications.
The illustrations below show how the connectors should be wired.
Be sure to use only high-grade cables.
Please use commercial RCA cables to connect the 2-track inputs
and outputs.
You can, of course, also connect unbalanced devices to the bal-
anced inputs/outputs. To do this, use either mono plugs or stereo
plugs with the ring and sleeve bridged (pins 1 and 3 in the case
of XLR connectors).
Caution! Never use unbalanced XLR connectors (PIN +
1 and 3 connected) on the MIC input connectors when
using the phantom power supply.
XLR connectionsFig. 3.1:
1/4" mono plugFig. 3.2:
1/4" stereo plugFig. 3.3:
Stereo plug for headphones connectionFig. 3.4:
EURORACK UB502/UB802/UB1002/UB1202
Specications 9
Specications4.
Mono inputs
Microphone inputs (IMP “Invisible” Mic Preamp)
Type XLR connector, electronically balanced,
discrete input circuit
Mic E.I.N.
1
(20 Hz - 20 kHz)
@ 0 Ω source resistance -134 dB / 135.7 dB A-weighted
@ 50 Ω source resistance -131 dB / 133.3 dB A-weighted
@ 150 Ω source resistance -129 dB / 130.5 dB A-weighted
Frequency response
<10 Hz - 150 kHz -1 dB
<10 Hz - 200 kHz -3 dB
Gain range +10 dB to +60 dB
Max. input level +12 dBu @ +10 dB GAIN
Impedance approx. 2.6 kΩ balanced
Signal-to-noise ratio 110 dB / 112 dB A-weighted (0 dBu In @
+22 dB GAIN)
Distortion (THD+N) 0.005 % / 0.004 % A-weighted
Line input
Type ¼" TRS jack, electronically balanced
Impedance approx. 20 kΩ balanced, approx. 10 kΩ
unbalanced
Gain range -10 dB to +40 dB
Max. input level +22 dBu @ 0 dB GAIN
Fade-out attenuation
2
(Crosstalk attenuation)
Main fader closed 90 dB
Channel muted 89.5 dB
Channel fader muted 89 dB
Frequency response (Mic In → Main Out)
<10 Hz - 90 kHz +0 dB / -1 dB
<10 Hz - 160 kHz +0 dB / -3 dB
Stereo inputs
Type ¼" TRS jack, electronically balanced
Impedance approx. 20 kΩ
Max. input level +22 dBu
Equalizer
EQ mono channels
LOW 80 Hz / ±15 dB
MID 2.5 kHz / ±15 dB
HIGH 12 kHz / ±15 dB
EQ stereo channels
LOW 80 Hz / ±15 dB
MID 2.5 kHz / ±15 dB
HIGH 12 kHz / ±15 dB
Send / Return
Aux sends
Type ¼" TS jack, unbalanced
Impedance approx. 120 Ω
Max. output level +22 dBu
Stereo aux returns
Type ¼" TRS jack, electronically balanced
Impedance approx. 20 kΩ balanced / approx. 10 kΩ
unbalanced
Max. input level +22 dBu
Outputs
Main outputs
Type ¼" TRS jack, unbalanced
Impedance approx. 120 Ω unbalanced
Max. output level +22 dBu
Control room outputs
Type ¼" TS jack, unbalanced
Impedance approx. 120 Ω
Max. output level +22 dBu
Headphones output
Type ¼" TRS jack, unbalanced
Max. output level +19 dBu / 150 Ω (+25 dBm)
Main mix system data
3
(Noise)
Main mix @ -∞, channel fader @ -∞
-106 dB / -109 dB A-weighted
Main mix @ 0 dB, channel fader @ -∞
-95 dB / -98 dB A-weighted
Main mix @ 0 dB, channel fader @ 0 dB
-84 dB / -87 dB A-weighted
Power supply
Power consumption UB502: 13 W
UB802: 17 W
UB1002: 18 W
UB1202: 23 W
Mains voltage
USA/Canada 120 V~, 60 Hz,
MXUL5 adapter
U.K./Australia 240 V~, 50 Hz,
MXUK5 adapter
Europe 230 V~, 50 Hz,
MXEU5 adapter
Japan 100 V~, 60 Hz,
MXJP5 adapter
Physical/weight
UB502
Dimensions (H x W x D) 1 5/6" / 1 1/2" (47 mm / 37 mm) x
5 1/4" (134 mm) x 7" (177 mm)
Weight (net) approx. 0.55 kg (1.21 lbs)
UB802
Dimensions (H x W x D) 1 5/6" / 1 1/2" (47 mm / 37 mm) x
7 2/5" (189 mm) x 8 2/3" (220 mm)
Weight (net) approx. 1.00 kg (2.21 lbs)
UB1002
Dimensions (H x W x D) 1 5/6" / 1 1/2" (47 mm / 37 mm) x
7 2/5" (189 mm) x 8 2/3" (220 mm)
Weight (net) approx. 1.05 kg (2.31 lbs)
UB1202
Dimensions (H x W x D) 1 5/6" / 1 1/2" (47 mm / 37 mm) x
9 1/2" (242 mm) x 8 2/3" (220 mm)
Weight (net) approx. 1.35 kg (2.97 lbs)
1
Equivalent Input Noise
2
Measuring conditions: 1 kHz rel. to 0 dBu; 20 Hz - 20 kHz; line input; main output;
unity gain.
3
20 Hz - 20 kHz; measured at main output. Channels 1 - 4 unity gain; EQ at; all chan-
nels on main mix; channels 1/3 as far left as possible; channels 2/4 as far right as
possible; reference = +6 dBu.
BEHRINGER is constantly striving to maintain the highest professional standards.
As a result of these efforts, modications may be made from time to time to existing
products without prior notice. Specications and appearance may differ from those
listed or illustrated.
EURORACK UB502/UB802/UB1002/UB1202
Warranty 10
Warranty 5.
Other warranty rights and national law § 1
1. This warranty does not exclude or limit the buyer’s statutory rights pro-
vided by national law, in particular, any such rights against the seller that
arise from a legally effective purchase contract.
2. The warranty regulations mentioned herein are applicable unless they
constitute an infringement of national warranty law.
Online registration § 2
Please do remember to register your new BEHRINGER equipment right
after your purchase by visiting http://www.behringer.com and kindly read
the terms and conditions of our warranty carefully. Registering your pur-
chase and equipment with us helps us process your repair claims quicker
and more efciently.
Thank you for your cooperation!
Warranty § 3
1. BEHRINGER (BEHRINGER International GmbH including all
BEHRINGER subsidiaries, except BEHRINGER Japan) warrants the me-
chanical and electronic components of this product to be free of defects in
material and workmanship for a period of one (1) year* from the original date
of purchase, in accordance with the warranty regulations described below.
If the product shows any defects within the specied warranty period that
are not excluded from this warranty as described under § 5, BEHRINGER
shall, at its discretion, either replace the product by providing a new or
reconditioned product or repair the product using suitable new or recon-
ditioned parts. In the case that other parts are used which constitute an
improvement, BEHRINGER may, at its discretion, charge the customer for
the additional cost of these parts. In case BEHRINGER decides to replace
the product, this warranty shall apply to the replacement product for the
remaining initial warranty period, i.e one year* from the date of purchase
of the initial product.
2. If the warranty claim proves to be justied, the product will be returned
to the user freight prepaid.
3. Warranty claims other than those indicated above are expressly
excluded.
Return authorization number § 4
1. To obtain warranty service, the buyer (or his authorized dealer) must call
BEHRINGER during normal business hours BEFORE returning the product.
All inquiries must be accompanied by a description of the problem. The buyer
or his authorized dealer will receive a return authorization number.
2. Subsequently, the product must be returned in its original shipping carton,
together with the return authorization number. The return shipment address
will be indicated by BEHRINGER.
3. Shipments without freight prepaid will not be accepted.
Warranty regulations§ 5
1. Warranty services will be furnished only if the product is accompanied
by a copy of the original retail dealer’s invoice. Any product deemed eligible
for repair or replacement under the terms of this warranty will be repaired
or replaced.
2. If the product needs to be modied or adapted in order to comply with
applicable technical or safety standards on a national or local level, in any
country which is not the country for which the product was originally devel-
oped and manufactured, this modication/adaptation shall not be considered
a defect in materials or workmanship. The warranty does not cover any such
modication/adaptation, irrespective of whether it was carried out properly
or not. Under the terms of this warranty, BEHRINGER shall not be held
responsible for any cost resulting from such a modication/adaptation.
3. Free inspections and maintenance/repair work are expressly excluded
from this warranty, in particular, if caused by improper handling of the product
by the user. This also applies to defects caused by normal wear and tear,
in particular, of faders, crossfaders, potentiometers, keys/buttons, tubes,
guitar strings, illuminants and similar parts.
4. Damage/defects caused by the following conditions are not covered
by this warranty:
improper handling, neglect or failure to operate the unit in compli- =
ance with the instructions given in BEHRINGER user or service
manuals.
connection or operation of the unit in any way that does not comply =
with the technical or safety regulations applicable in the country
where the product is used.
damage/defects caused by force majeure or any other condition =
that is beyond the control of BEHRINGER.
5. Any repair or opening of the unit carried out by unauthorized personnel
(user included) will void the warranty.
6. If an inspection of the product by BEHRINGER shows that the defect in
question is not covered by the warranty,
7. Products which do not meet the terms of this warranty will be repaired
exclusively at the buyer’s expense. BEHRINGER will inform the buyer of any
such circumstance. If the buyer fails to submit a written repair order within
6 weeks after notication, BEHRINGER will return the unit. Costs for freight
and packing will be invoiced separately C.O.D. When the buyer has sent in
a written repair order such costs will also be invoiced separately.
Warranty transferability§ 6
This warranty is extended exclusively to the original buyer (customer of retail
dealer) and is not transferable to anyone who may subsequently purchase
this product. No other person (retail dealer, etc.) shall be entitled to give
any warranty promise on behalf of BEHRINGER.
Claim for damages§ 7
Failure of BEHRINGER to provide proper warranty service shall not entitle
the buyer to claim (consequential) damages. In no event shall the liability
of BEHRINGER exceed the invoiced value of the product. * Customers in
the European Union please contact BEHRINGER Germany Support for
further details.
Technical specications and appearance are subject to change without notice. The information contained herein is correct at the time of printing. All trademarks (except BEHRINGER,
the BEHRINGER logo, JUST LISTEN and EURORACK) mentioned belong to their respective owners, and such use neither constitutes a claim of the trademarks by BEHRINGER
nor afliation of the trademark owners with BEHRINGER. BEHRINGER accepts no liability for any loss which may be suffered by any person who relies either wholly or in part
upon any description, photograph or statement contained herein. Colors and specications may vary slightly from product. Our products are sold through authorized dealers only.
Distributors and dealers are not agents of BEHRINGER and have absolutely no authority to bind BEHRINGER by any express or implied undertaking or representation. This
manual is copyrighted. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of
any kind, for any purpose, without the express written permission of BEHRINGER International GmbH.
ALL RIGHTS RESERVED. © 2008 BEHRINGER International GmbH, Hanns-Martin-Schleyer-Str. 36-38, 47877 Willich-Muenchheide II, Germany. Tel. +49 2154 9206 0, Fax
+49 2154 9206 4903
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
Responsible party name: BEHRINGER USA, Inc.
Address: 18912 North Creek Parkway, Suite 200
Bothell, WA 98011, USA
Phone/Fax No.: Phone: +1 425 672 0816,
Fax: +1 425 673 7647
hereby declares that the product(s)
complies/comply with the FCC rules as mentioned in the following paragraph:
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Important information:
Changes or modifications to the equipment not expressly approved by
BEHRINGER USA can void the user’s authority to use the equipment.
EURORACK
UB502/UB802/UB1002/UB1202
UB502
UB802
UB1002
UB1202
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Behringer EURORACK UB1202 User manual

EURORACK UB1202
Behringer
Brand
Behringer
Model
EURORACK UB1202
Category
Audio mixers
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents