Page is loading ...
Page | 1
PO#:13745
WS471400TX
Joplin Leaning Mirror
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises, Inc.
Customer Service: 1-800-633-5096
www.seidal.com
Page | 2
Joplin Leaning Mirror
Parts List
Please review all parts and hardware before disposing of any packaging. Before beginning assembly, separate
each type of hardware. Carefully study the diagrams below and check that you have all parts indicated. Call
Customer Service if missing hardware. Using the incorrect hardware will cause damage.
1
.
Quantity
of 1
Mirror
A.
Quantity
of 3
Plastic Anchors
B
.
Quantity
of 5
Screws 1/8” x 1-1/2”L
C.
Quantity
of 1
Screws 1/8” x 5/8”L
D.
Quantity
of 2
Brackets
E.
Quant
ity
of 1
Plastic Strap
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Avoid rubbing or scratching the surface with rough
or abrasive objects.
For repla
cement parts or questions, please
call customer service at 1-800-633-5096.
Tool List: 3/16" drill bit, drill, tape measure and pencil.
Assembly Tool Required:
No.2 Phillips Screwdriver (Not Included)
Page | 3
Note: Drilled hole or plastic anchor not required when
mounting to stud, use screw only. We do not supply hardware
for mounting on concrete walls.
Figure 1
Find a desired location and mark 2
locations for screws on wall.
One screw (for each unit) must be
attached directly into a wall stud. Wall
anchor is not needed when mounting to
wall stud.
Drill one of marked 3/16" hole (for each
unit), this hole will be for the Plastic
Anchor (A).
Insert Plastic Anchor (A) into hole on
wall (use a hammer help).
Using Phillips screwdriver, insert
Screws (B) into Plastic Anchor (A) and
the other into the wall stud. Turn screws
until there is a gap of approximately
3mm between head of screw and wall.
Figure 2
Hang mirror onto Screws (B) and verify
mirror is resting securely.
Now your Joplin Leaning Mirror is ready
to use!
Joplin Leaning Mirror
Assembly Instructions
The hole measuremen
ts
on the wall must match
with hole measurements
on back of unit.
Page | 4
If you prefer to hang this product in horizontal configuration, please follow below instructions.
Note: Drilled hole or plastic anchor not required when
mounting to stud, use screw only. We do not supply hardware
for mounting on concrete walls.
Figure 3
Find a desired location and mark 2
locations for screws on wall.
One screw (for each unit) must be
attached directly into a wall stud. Wall
anchor is not needed when mounting to
wall stud.
Drill one of marked 3/16" hole (for each
unit).
Insert plastic anchor (A) into hole on
wall (use a hammer help).
Using Phillips screwdriver, install
Screws (B) into Plastic Anchor (A) and
remaining marked hole. Turn screws
until there is a gap of approximately
3mm between head of screw and wall.
Figure 4
Hang mirror onto Screws (B) and verify
mirror is resting securely.
Now your Joplin Leaning Mirror is ready
to use!
The hole measurements
on the wall must match
with hole measurements
on back of unit.
Page | 5
If you prefer to hang this product against the wall configuration, please follow below instructions.
Figure 5
Mark one desired locations on wall and
drill a 3/16" hole.
Insert Plastic Anchor (A) into hole on
wall (use a hammer to help). Make
sure plastic anchor is flush with wall.
Attach Bracket (D) onto wall using
Screw (B).
Tighten screw with Philips screwdriver.
Figure 6
Attach Bracket (D) to back panel using
Screw (C).
Tighten screw with Philips screwdriver.
D
D
Page | 6
Figure 7
Move this item close to wall bracket.
Tie both brackets together with Plastic
Straps (E).
Anti-tipping hardware must be used
for this product to avoid tipping and
injury.
Now your Joplin Leaning Mirror is ready
to use!
Page | 7
Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time frame.
Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s) and we are not
responsible for any damages due to product modification(s). If damages or missing parts are not reported within 90 days
of your receipt, we are under no obligation to provide parts or replacement merchandise.
For product issues, please contact Southern Enterprises at 800-633-5096 (toll-free) / 972-869-0111 (Dallas), Mon-Fri
9am – 4pm CST, or email us at [email protected]. Please ask for customer service representative for issues involving
damages or replacement parts. Please ask for technical assistance representative for any issues with product and
assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service: 1-800-633-5096
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
/
