COBHAM EXPLORER 540 Installation guide

Brand: COBHAM

Model: EXPLORER 540

Category: Networking

Type: Installation guide

COBHAM EXPLORER 540 is a versatile satellite terminal designed for reliable and secure communication in remote locations. With its compact size and rugged construction, it's ideal for applications such as maritime, land mobile, and SCADA systems. The EXPLORER 540 supports both M2M and standard class 2 services, providing flexible connectivity options. It features Ethernet and USB interfaces for data transfer, as well as GPIO for remote control and status monitoring. TheEXPLORER 540 is also equipped with a built-in web interface for easy configuration and management.

What’s in the box?

To maintain the Ingress Protection of the EXPLORER 540 and to avoid cables

accidentally being disconnected, all cable connections are made inside the

small compartment at the back of the EXPLORER 540.

• Use the provided Torx bit to open the small compartment at the back

of the terminal.

• Useaatbladescrewdriver(max.2mmwide)topressdownthe

spring-loaded terminals.

• Useaatbladescrewdriver(max.3.5mmwide)tounscrewandfasten

thescrewterminals.

1. Leadthecable(s)throughthecablegland(s)andgasket(s)(suitablefor

cablediameter5-10mm).Makesurethecableglandsttightly.

2. Connect the cables accor-

dingtoyourconguration.

Seethereverseofthisguide

forpinoutandexamplecon-

gurationdrawing.

The RJ-45 connector of the

LANcablecanpassthrough

thecablegland.(seepicture)

3. IfyouarenotusingPoEto

powertheEXPLORER540,

connectapowercable

betweentheDCinputterminalsandanexternalbatteryorpowersupply.

4. Whenallcablesareconnected,mountthecoverforthecompartment

andtightenthescrewswiththeincludedTorxbit.

Important!Ifyouonlyneedtoinstallonecable,mounttheprovidedblind

plugintheunusedholetomaintaintheIngressProtection(IPgrade)ofthe

terminal.

Step 2: Connect cables

Step 3: Install the EXPLORER 540

Thefollowingitemsareincludedinthe

delivery:

• EXPLORER 540 terminal

• Polemountkit

• 2Cableglandsand1Blindplug

• TorxbitSizeTX10(tamper

resistant,1/4”Hexdrive)for

mounting/dismountingthecover

for the small compartment

• Installationguide(thisguide)

EXPLORER540Userandintegrator’smanual(partno.98-148232)aswell

asotherlanguageversionsofthisinstallationguideareavailablefordown-

loadattheSelfServiceCenter.Gotowww.cobham.com/satcomandselect

ServiceandSupport>CobhamSATCOMServiceandSupport>24-7Self

ServiceCenter/TechnicalDownloads.

Apolemountkitisincludedinthedelivery.TomounttheEXPLORER540on

apole,doasfollows:

1. AttachthebaseofthepolemountbrackettotheEXPLORER540using

theincludedHexLkeyonthe4

screws.Caution! Max.lengthofthe

screwsis9mm!Longerscrewscan

damage the EXPLORER 540.

2. Unscrewtwoofthelongscrewsfrom

thepolemountkittoleaveoneside

open for the pole.

3. Placethepolemountkitwiththe

EXPLORER540aroundthepoleas

shown.

4. Remountthetworemaininglong

screws.Donottightenthescrews

completelyuntilyouhavepointed

the antenna.

5. Powerupthesystem.

ObservetheLEDbetweenthecable

glands(seeLEDdescriptiononthe

back).

• LEDashingrapidlygreen:

Startingup

• LEDashingyellow:Pointing

• LEDsteadyyellow:Warning!

See Vericaton on the back.

6. WhenLEDashesyellow:Turnand

tilttheEXPLORER540andusethe

pointingsoundtoobtainthehighest

possiblesignalstrength.(continuous

sound=bestsignal)

7. Whenyouhavethehighestpossible

signalstrength.tightenallthescrews

to keep the EXPLORER 540 in the

pointed position.

TheEXPLORER540willautomatically

exit the pointing process once it has

detectedastableBGANsignal.

8. When the pointing process has en-

ded,theLEDchangesasfollows:

• LEDashinggreen:Verifyingnetworkconnection

• LEDsteadygreenandthenoff:Ready-installationprocesshasended

successfully.TheLEDisdisabled(off)afterafewminutes.

IftheLEDissteadyyellow,theinstallationfailedandthereisawarning.

IfyoucanconnectacomputerlocallytotheEXPLORER540,youcanusethe

webinterfacetofollowtheprogressonscreen,seeanywarnings,andrestart

the installation if necessary. See Verication on the back.

EXPLORER 540

Installation guide

YouneedaBGANSIMcardforeitherM2Morstandardclass2services.To

inserttheSIMcard,doasfollows:

NOTE:MakesuretheEXPLORER540

is notpoweredwhenyouinsertor

removetheSIMcard!

1. Open the cover for the small com-

partment at the back of the EXPLO-

RER540.UsetheincludedTorxbit

tounscrewthescrews.

2. LocatetheSIMholderinthe

middle of the compartment.

3. SlidethelocktoreleasetheSIM

holder.

4. LifttheendoftheSIMholderand

inserttheSIMcardasshown.

5. LowertheSIMcardholderwith

theSIMcardinsertedandlockit.

6. Whenallcablesareconnected,put

the cover back on and tighten the

screws.

Step 1: Insert SIM card

Disclaimer: Any responsibility or liability for loss or damage in connection with the use of this product and the accompanying documentation is disclaimed

by Thrane & Thrane A/S. The information in this manual is provided for information purposes only, is subject to change without notice and may contain

errors or inaccuracies. The manuals are periodically revised and updated. Anyone relying on this information should acquire the most current version e.g.

from cobham.com/satcom or from the distributor. Thrane & Thrane A/S is not responsible for the content or accuracy of any translations or reproductions,

in whole or in part, of this manual from any other source. Thrane & Thrane A/S trading as Cobham SATCOM.

X2:Ethernet,

RJ-45

X1: Ethernet,

Spring-loaded

terminals

X4:DCinput,

Screwterminals

X5: I/O,

Spring-loaded

terminals

X6:USBMicroB

(inthesidewall-

notvisiblehere)

EXPLORER 540 terminal

with pole mount kit

X7:ChassisGND,

Screwterminal

LED=

98-148231-A

www.cobham.com/satcom

System Conguration - Example

Technical specications

Item Specication

Dimensions 202x202x51.8mm

8.0x8.0x2.0inches

Weight 1.6kg/3.5lbs(excl.cellularmodem)

Operatingtemperature -40to75°C

PowersupplyPoE

PowersupplyDC

Accordingto:PoE+IEEE802.3attype2class4

10.5to32VDC

Powerconsumption Powersave(Wake oncongured):110mW

Sleepmode:2.5W

Max.powerwhentransmitting:

• PoE:24W

• DC:21W

IP grade IP66

Number Cable Requirements

1 DCPowercable 1.5 mm

,UVresistant,Temperature:-40to+75deg.C,Maxcable

length:12metersat12Voperation,200metersat24Voperation

2 LAN cable Cable:EthernetMin.Cat5Solidcopperwire,STP.Max.length:100m

PoE source according to PoE+ IEEE 802.3at type 2 class 4

3 I/O cables 0,2mm

to 0,5 mm

(26AWGtil20AWG),outputupto2A.

Useshieldedcableoninputifnotactivelydrivenhigh/low.

If the LEDturnssteady yellow,itmeanstheinstallationfailed,e.g.becau-

setheterminalwasunabletodetectastableBGANsignalorveriifythe

networkconnection.

Ifyouconnectacomputerlocallytotheterminal,youcanusethebuilt-in

webinterfacetofollowtheprogressonscreenduringinstallation,andtosee

warningmessagesincasetheinstallationfailed.

1. ConnectyourcomputertotheLANinterfaceoftheEXPLORER540.

2. Openyourbrowseronthe

connectedcomputer.

3. Poweruptheterminal.

4. Accessthewebinterface

at the local IP address

(default192.168.0.1).

5. Entertheusername:User

andpassword:<serialnum-

beroftheterminal>.

Verifying and troubleshooting the installation

LED status Description

Off LightindicatorhasbeendisabledorPoweroff

Greenashingrapidly Startingup

Yellowashing BGANpointing

Greenashing Verifyingnetworkconnectivity

Green constant Ready

Yellowashingrapidly Closingdown

Yellowconstant Warning(userrecoverable).

Seewebinterfaceforthewarningtext.

Red constant Error.Seethewebinterface.

Blueashing Uploadingsoftwaretotheterminal

LAN/PoE connector (X1 or X2)

Pin Signal

1 TXp

2 TXm

3 RXp

4 POE+

5 POE+

6 RXm

7 POE-

8 POE-

DC power connector (X4)

Pin Signal

1 DCIN+

2 DCIN-

3 GND(optional-forconnection

ofshield)

Connectors and pin allocation

USB connector (X6)

Pin Signal

1 +5V

2 Dm

3 Dp

4 ID

5 GND

I/O connector (X5)

Pin Signal Details

1 GPI Requestwakeupinput

2 GPO Terminalreadyoutput

3 GPIO M2Mremotecontrol/

status,input/output

4 GND Ground

IMPORTANT:Youmustuseeither X1 orX2forLAN,notboth!

TheEXPLORER540hasthefollowingconnectors/terminals:

• X1: LAN/PoE, Spring-loaded terminals

• X2:LAN/PoE,RJ-45connector

• X3:SIMcard

• X4:DCinput,Screwterminals

• X5: I/O, Spring-loaded terminals

• X6:USB,microBconnector

• X7:ChassisGND,Screwterminal

Battery

M2Mindoor

equipment

Indoorequipment

PoE

injector

Probe

Solar panel

EthernetwithPoE

Internet

BGANM2Mservicevia

satellite

Light indicator

(LED)

Note:TheLEDisdisabled after completion

of the installation process.

Note:Thisdrawingisjustanexample.Yourcongurationmayuseothertypesofequipment.

COBHAM EXPLORER 540 Installation guide

Brand: COBHAM

Model: EXPLORER 540

Category: Networking

Type: Installation guide

Download PDF

report

COBHAM EXPLORER 540 Installation guide

COBHAM EXPLORER 540 Installation guide

Related papers

Other documents