Whirlpool WHP1000SQ Owner's manual

Brand: Whirlpool

Model: WHP1000SQ

Type: Owner's manual

This manual is also suitable for

WHP1000S

INSTALLATION INSTRUCTIONS PEDESTAL

For use only with front load washer and dryers

INSTRUCCIONES DE INSTALACIÓN PEDESTAL

Para uso sólo con lavadoras y secadoras de carga frontal

INSTRUCTIONS D’INSTALLATION PIÉDESTAL

Pour utilisation avec les produits suivants seulement

laveuses et sécheuses à chargement par l'avant

W10043500

10"

(25,4 cm)

27"

(68,6 cm)

⁵⁄₈

(60 cm)

Table of Contents/Índice/Table des matières.............................................................................2

NOTE: If the dryer and pedestal assembly is located in a garage,

8" (20.3 cm) must be added under the pedestal so that the dryer

is 18" (46 cm) above the garage floor.

PEDESTAL SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline,

away from dryer.

Place dryer at least 18 inches (46 cm) above the floor for

a garage installation.

Failure do to so can result in death, explosion, or fire.

Tools and Parts

Gather the required tools and parts before starting installation.

Tools needed

■ utility knife

■ ¹⁄₄" hex head ratchet or open-end wrench

■ level

■ ⁹⁄₁₆" open-end wrench

■ pliers or slip-joint pliers

■ bucket

Parts supplied

■ four #12 x ⁵⁄₈" hex head sheet metal screws (in parts bag)

■ Installation Instructions

TABLE OF

CONTENTS

PEDESTAL SAFETY . . . . . . . . . . . . . . . . . . . . .2

Tools and Parts . . . . . . . . . . . . . . . . . . .2

INSTALLATION INSTRUCTIONS . . . . . . . . .3

Before Installing Pedestal . . . . . . . . .3

Installing the Pedestal . . . . . . . . . . . .4

Complete Installation . . . . . . . . . . . . .4

KENMORE LAUNDRY WARRANTY . . . . . .6

WHIRLPOOL LAUNDRY WARRANTY . . . .7

TABLE DES

MATIÈRES

SÉCURITÉ DU PIÉDESTAL . . . . . . . . . . . . .14

Outillage et pièces . . . . . . . . . . . . . . .14

INSTRUCTIONS D'INSTALLATION . . . . . .15

Avant l’installation du piédestal . . . . .15

Installation du piédestal . . . . . . . . . .16

Achever l'installation . . . . . . . . . . . .17

GARANTIE DE BUANDERIE

KENMORE . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

GARANTIE DE BUANDERIE

WHIRLPOOL . . . . . . . . . . . . . . . . . . . . . . . . . .19

ÍNDICE

SEGURIDAD DEL PEDESTAL . . . . . . . . . . .8

Piezas y herramientas . . . . . . . . . . . . .8

INSTRUCCIONES DE INSTALACIÓN . . . . .9

Antes de instalar el pedestal . . . . . . . .9

Instalación del pedestal . . . . . . . . . .10

Complete la instalación . . . . . . . . . . .11

GARANTÍA DE LAVANDERÍA

KENMORE . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

GARANTÍA DE LAVANDERÍA

WHIRLPOOL . . . . . . . . . . . . . . . . . . . . . . . . . .13

Uninstalling your electric dryer

1. Unplug the power supply cord.

2. Pull the dryer away from the wall enough to loosen the vent

clamp. Loosen the clamp and gently remove the exhaust vent

from the dryer exhaust outlet.

3. Pull the dryer away from wall so that it can be tipped on its

back.

4. Protect the floor with a large piece of cardboard cut from the

pedestal carton. Lay the dryer on its back (make sure that the

power supply cord is not under the dryer) so that the

cardboard is under the entire lower back edge of the dryer

(see Figure 1). Go to “Installing the Pedestal” section.

Uninstalling your gas dryer

1. Unplug the power supply cord.

2. Turn off the gas supply.

3. Pull the dryer away from the wall enough to loosen the vent

clamp. Loosen the clamp and gently remove the exhaust vent

from the dryer exhaust outlet.

4. Disconnect the flexible gas supply line from the dryer. Put a

piece of tape over the open ends of the gas line connection

fittings.

5. Pull the dryer away from wall so that it can be tipped on its

back.

6. Protect the floor with a large piece of cardboard cut from the

pedestal carton. Lay the dryer on its back (make sure that the

power supply cord is not under the dryer) so that the

cardboard is under the entire lower back edge of the dryer

(see Figure 1). Go to “Installing the Pedestal” section.

Before Installing Pedestal

IMPORTANT: If your washer and dryer are already installed, they

must be uninstalled.

If you need to uninstall your washer or dryer, see the installation

instructions that came with your model for tools required.

Uninstalling your washer

NOTE: If the washer is to be transported, call your local service

center. To prevent suspension and structural damage, your

machine must be properly set up for relocation by a certified

technician.

1. Turn off the hot and cold water faucets.

2. Unplug the power supply cord.

3. Slowly loosen the fill hoses at the faucets to relieve the water

pressure. Use a sponge or towel to absorb the released water.

4. Remove the “HOT” and “COLD” fill hoses from the back of

the washer. Drain the water from the hoses into a bucket.

5. Squeeze the ears of the drain hose clamp with pliers to open

and slide the clamp down the hose. Disconnect the drain

hose from the washer and drain any water in the hose into a

bucket.

6. Pull the washer away from wall so it can be tipped on its

back.

7. Protect the floor with a large piece of cardboard cut from the

pedestal carton. Lay the washer on its back (make sure that

the power supply cord is not under the washer) so that the

cardboard is under the entire lower back edge of the washer.

An additional small amount of water will drain out of the

washer when it is tipped back. Go to “Installing the Pedestal”

section.

cardboard

12"

(30.5 cm)

15"

(38.1 cm)

INSTALLATION INSTRUCTIONS

WARNING

Excessive Weight Hazard

Use two or more people to move and uninstall washer.

Failure to do so can result in back or other injury.

WARNING

Excessive Weight Hazard

Use two or more people to move and uninstall dryer.

Failure to do so can result in back or other injury.

WARNING

Excessive Weight Hazard

Use two or more people to move and uninstall dryer.

Failure to do so can result in back or other injury.

Figure 1

2. If your washer/dryer has feet installed, remove them. Do not

install the feet that came with a new washer/dryer.

3. Partially install the two #12 x ⁵⁄₈" hex head sheet metal screws

in the lower holes. Leave a space of about ³⁄₈" (1 cm) between

the screw head and the bottom of the washer/dryer.

4. Move the pedestal against the washer/dryer bottom. Slide the

pedestal’s keyhole slots over the lower two partially installed

screws.

5. Position the pedestal toward the front of the washer/dryer and

install the two remaining hex head sheet metal screws. Do not

tighten completely.

6. Align the sides of the pedestal so that they are even with the

sides of the washer/dryer. Reach inside pedestal opening and

securely tighten all four pedestal screws.

7. Tip the washer/dryer back to its upright position. Remove and

discard packaging including the washer’s plastic film, corner

posts and top cap.

Complete installation

1. Slide the washer/dryer close to its final location.

2. Follow the installation instructions that came with your model

to finish installing or reinstalling your washer/dryer (i.e., hoses,

vents, etc.).

3. Level the washer/dryer from side to side and front to back.

NOTE: Make sure all four pedestal feet are in solid contact

with the floor.

Place a level on the top. Locate the ¹⁄₄" hex head screws on

the top of each pedestal foot. Reach inside the pedestal and

use a ¹⁄₄" hex head ratchet or open-end wrench to adjust the

feet up or down as needed to level the washer/dryer.

lower screws in

keyhole slots

dryer

shown

If your washer or dryer is still in its packaging

1. Position the packaged washer/dryer close to its final position.

Cut the packaging as follows:

Washer: Cut plastic film along dotted cut line around the

base. Do not remove the packaging.

Dryer: Cut carton around top and down corners along dotted

cut lines. Lay all four carton sides on floor. Discard carton top

and corner posts.

IMPORTANT: Leave carton bottom underneath dryer.

2. Lay washer/dryer on its back.

NOTE: When laying the washer on its back, hold the bottom

cap down on the floor. Do not remove the plastic film, corner

posts or top cap. These protect the floor and washer back.

When laying the dryer on its back, the floor and dryer back

are protected by cartoning.

Installing the Pedestal

Follow these instructions to install the pedestal on a washer or dryer.

The parts bag contains four #12 x ⁵⁄₈" hex head sheet metal

screws used in step 3, and the Installation Instructions.

1. Make sure that all four spacer pads are in place on the top of

the pedestal. These pads reduce vibration between the

pedestal and the washer/dryer.

WARNING

Excessive Weight Hazard

Use two or more people to move washer or dryer.

Failure to do so can result in back or other injury.

WARNING

Excessive Weight Hazard

Use two or more people to move and install pedestal.

Failure to do so can result in back or other injury.

carton

sides

dryer

shown

spacer pads

dryer bottom

install screws

washer bottom

install screws

4. When the washer/dryer is level, use a ⁹⁄₁₆" open-end wrench

to securely tighten all four locknuts against the pedestal. The

locknuts must be tightened to prevent vibration.

5. Align front panel with pedestal and snap in place.

For washer/dryer models that are 38" (96.5 cm) high, the wide

edge should be placed on top.

For washer/dryer models that are 36" (91.4 cm) high, the wide

edge should be placed on bottom.

locknut

36" (91.4 cm)

models

38" (96.5 cm)

models

wide

narrow

LAUNDRY PRODUCT WARRANTY

Bef ore you call f or Service

If this laundry product was purchased at Sears, the ìKenmore

Laundry Product Warranty” applies (see following).

If this laundry product was purchased elsewhere, the “Whirlpool Corporation Laundry Product Warranty” applies (see following). Please

have your sales receipt available when you call Whirlpool Corporation for service under the “Whirlpool Corporation Laundry Product

Warranty.”

KENMORE

LAUNDRY PRODUCT WARRANTY

ONE YEAR LIMITED WARRANTY

When installed, operated and maintained according to all

instructions supplied with the product, if this laundry product fails

due to a defect in material or workmanship within one year from

the date of purchase, call 1-800-4-MY-HOME to arrange for free

repair. If this laundry product is used for other than private family

purposes, this warranty applies for only 90 days from the date of

purchase.

THIS WARRANTY COVERS ONLY DEFECTS IN MATERIAL

AND WORKMANSHIP. SEARS WILL NOT PAY FOR:

1. Expendable items that can wear out from normal use,

including but not limited to filters, belts, light bulbs, and bags.

2. A service technician to instruct the user in correct product

installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed,

operated or maintained according to all instruction

s supplied

with the product.

5. Damage to or failure of this product resulting from accident,

abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the use of

detergents, cleaners, chemicals or utensils other than those

recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from

unauthorized modifications made to this product.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF

REMEDIES

Customer's sole and exclusive remedy under this limited warranty

shall be product repair as provided herein. Implied warranties,

including warranties of merchantability or fitness for a particular

purpose, are limited to one year or the

shortest period allowed by

law. Sears shall not be liable for incidental or consequential

damages. Some states and provinces do not allow the exclusion

or limitation of incidental or consequential damages, or limitations

on the duration of implied warranties of merchantability or fitness,

so these exclusions or limitations may not apply to you.

This warranty applies only while this laundry product is used in the

United States and Canada.

This warranty gives you specific legal rights, and you may also

have other rights which vary from state to state.

Sears, Roebuck and Co.

Hoffman Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2B8

PRODUCT RECORD

In the space below, record your complete model number, serial

number, and purchase date. You can find this information on the

model and serial number label located on the product.

Have this information available to help you obtain assistance or

service more quickly whenever you contact Sears concerning

your laundry product.

Model number __ __ __.__________________________________________

Serial number __________________________________________________

Purchase date __________________________________________________

Save these instructions and your sales receipt for future

reference.

WHIRLPOOL CORPORA TION LAUNDRY PR ODUCT WARRANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this product is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool or Whirlpool Canada (hereafter “Whirlpool”) will pay for factory specified replacement parts and

repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.

ITEMS WHIRLPOOL WILL NOT PAY FOR

1. Service calls to correct the installation of your product, to instruct you how to use your product, to replace or repair house fuses or

to correct house wiring or plumbing.

2. Repairs when your product is used for other than normal, single-family household use.

3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

4. Replacement parts or repair labor costs for units operated outside the United States or Canada.

5. Pickup and delivery. This product is designed to be repaired in the home.

6. Repairs to parts or systems res

ulting from unauthorized modifications made to the product.

7. Expenses for travel and transportation for product service in remote locations.

8. The removal and reinstallation of your product if it is installed in an inaccessible location or is not installed in accordance with

published installation instructions.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM

STATE TO STATE OR PROVINCE

TO PROVINCE.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if

another warranty applies. If you need service, in the U.S.A., call 1-800-422-1230. In Canada, call 1-800-807-6777.

6/06

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major product to

better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name____________________________________________________

Address ________________________________________________________

Phone number__________________________________________________

Model number __________________________________________________

Serial number __________________________________________________

Purchase date __________________________________________________

Page is loading ...

W10043500

KENMORE, KENMORE ELITE, are trademarks of Sears, Roebuck and Co.

WHIRLPOOL, is a trademark of Whirlpool, U.S.A.

KENMORE, KENMORE ELITE, son marcas de comercio de Sears, Roebuck and Co.

WHIRLPOOL, son marcas de comercio de Whirlpool, U.S.A.

KENMORE, KENMORE ELITE, sont des marques de commerce de Sears, Roebuck and Co.

WHIRLPOOL, sont des marques de commerce de Whirpool, U.S.A.

Printed in U.S.A.

Impreso en EE.UU.

Imprimé aux É-U.

06/2006

Whirlpool WHP1000SQ Owner's manual

Brand: Whirlpool

Model: WHP1000SQ

Type: Owner's manual

This manual is also suitable for

WHP1000S

Download PDF

report

in other languages

français: Whirlpool WHP1000SQ Le manuel du propriétaire
español: Whirlpool WHP1000SQ El manual del propietario

Whirlpool WHP1000SQ Owner's manual

This manual is also suitable for

Whirlpool WHP1000SQ Owner's manual

in other languages

Related papers

Other documents