Hunter Fan 27543 Owner's manual

Brand: Hunter Fan

Model: 27543

Category: Household fans

Type: Owner's manual

Type 2 ModelsType 2 ModelsType 2 Models

Form# 42409-01

20100617

For Your Records and

Warranty Assistance

For reference, also attach your receipt or a copy

of your receipt to the manual.

__________________________________________

Model Name

__________________________________________

Model No.

__________________________________________

Date Purchased

__________________________________________

Where Purchased

English Français

Owner’s Guide and Installation Manual

 42409-01•05/02/06

42409-01•06/17/10•HunterFanCompany

Table of Contents

1•GettingReady ................................................... 6

2•InstallingtheCeilingPlate ..........................7

3•AssemblingandHangingtheFan ..........8

4•SecuringFantoSecondary

 SupportSystem ................................................9

5•WiringtheFan ............................................... 10

6•InstallingtheCanopyandCanopy

 TrimRing .......................................................... 11

7•AssemblingtheBlades .............................. 12

8•CompletingYourInstallationWith

 orWithoutaLightFixture ....................... 13

9•OperatingandCleaning

 YourCeilingFan............................................. 17

10•Troubleshooting ......................................... 18

Welcome

YournewHunter

ceilingfanisanadditiontoyourhomeorocethat

willprovidecomfortandperformanceformanyyears.isinstallation

andoperationmanualgivesyoucompleteinstructionsforinstalling

andoperatingyourfan.

Weareproudofourwork.Weappreciatetheopportunitytosupply

youwiththebestceilingfanavailableanywhereintheworld.

Beforeinstallingyourfan,foryourrecordsandwarrantyassistance,

recordinformationfromthecartonandHunternameplatelabel

(locatedonthetopofthefanmotorhousing).

Cautions and Warnings

• READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING

INSTALLATION. SAVE THESE INSTRUCTIONS.

•UseonlyHunterreplacementparts.

•Toreducetheriskofpersonalinjury,attachthefandirectlytothe

supportstructureofthebuildingaccordingtotheseinstructions,

anduseonlythehardwaresupplied.

•Toavoidpossibleelectricalshock,beforeinstallingyourfan,

disconnectthepowerbyturningothecircuitbreakerstothe

outletboxandassociatedwallswitchlocation.Ifyoucannotlock

thecircuitbreakersintheoposition,securelyfastenaprominent

warningdevice,suchasatag,totheservicepanel.

•Allwiringmustbeinaccordancewithnationalandlocalelectrical

codesandANSI/NFPA70.Ifyouareunfamiliarwithwiring,usea

qualiedelectrician.

•Toreducetheriskofpersonalinjury,donotbendtheblade

attachmentsystemwheninstalling,balancing,orcleaningthefan.

Neverinsertforeignobjectsbetweenrotatingfanblades.

•Toreducetheriskofre,electricalshock,ormotordamage,donot

useasolid-statespeedcontrolwiththisfan.UseonlyHunterspeed

controls,whicharesolidstate.

•isproductconformstoULSTD507andiscertiedtoSTDC22.2

No.113

•Washyourhandsafteryourfaninstallationiscomplete.

42409-01•06/17/10•HunterFanCompany

Preparing the Fan Site

7’Minimum

Bladesto

Floor

8’Minimum

Ceiling

Height

30”From

Wallor

Nearest

Obstruction

Step 1 - Choose the Fan Site

Properceilingfanlocationandattachmenttothebuilding

structureareessentialforsafety,reliableoperation,maximum

eciency,andenergysavings.

Choose a fan site where:

•Noobjectcancomeincontactwiththerotatingfanbladesduring

normaloperation.

•efanbladesareatleast7feetabovetheoorandtheceilingis

atleast8feethigh.

•efanbladeshavenoobstructionstoairow,suchaswallsor

posts,within30inchesofthefanbladetips.

•efanisdirectlybelowajoistorsupportbracethatwillholdthe

outletboxandthefullweightofthefan.

Checklist for Existing Fan Site

Ifyouwanttouseanexistingfansite,completethefollowingchecklistto

determineifthesiteisacceptableandsafeforyournewHunterfan.Ifyou

cannotcheckoeveryitem,prepareanewfansiteasdescribedonthis

page.

Fan Support System

•Fan attaches directly to building structure.

•Fansupportsystemwillholdfullweightofthefanandlightkit.

Ceiling Hole

•eoutletboxclearanceholeisdirectlybelowthejoistorsupportbrace.

Outlet Box

•eoutletboxisanUL-approvedoctagonal4”x1-1/2”outletbox(oras

speciedbythesupportbracemanufacturer).

•eoutletboxissecuredtothejoistorsupportbracebywoodscrews

andwashersthroughtheinnerholesofoutletbox.

•eouterholesoftheoutletboxarealignedwithjoistorsupportbrace.

•ebottomoftheoutletboxisrecessedaminimumof1/16”into

ceiling.

Wiring

•eelectricalcableissecuredtooutletboxbyanapprovedconnector.

•Sixinchesofleadwiresextendfromoutletbox.

Ifyourexistingfansiteissuitable,skipaheadtoSection2 • Installing the

Ceiling Plate.

Suitable Existing Fan Site

FanSupport

System

FanSupport

System

Wiring

OutletBox

42409-01•06/17/10•HunterFanCompany

Preparing the Fan Site (continued)

CAUTION:Allwiringmustbein

accordancewithnationalandlocal

electricalcodesandANSI/NFPA70.If

youareunfamiliarwithwiring,usea

qualiedelectrician.

Steps 2 – 3

Step 4

Step 5

Step 2 - Cut the Ceiling Hole

2-1.Locatethesitefortheceilingholedirectlybelowthejoistorsupportbracethat

willholdtheoutletboxandfan.

2-2.Cuta4”diameterholethroughthedrywallorplasteroftheceiling.Youwilluse

theholetoinstallthesupportbraceandoutletbox.

Step 3 - Install a Support Brace, If Necessary

Determineifthereisaceilingjoistdirectlyabovetheceilinghole.Ifthejoististhere,

determineifitispositionedtoallowyoutorecesstheoutletboxaminimumof

1/16”intotheceiling.IfNOT,installasupportbraceasfollows:

3-1.Attacha2”x4”supportbracebetweentwojoists.Positionittoallowyouto

recessthebottomoftheoutletboxaminimumof1/16”intotheceiling.

3-2.Checkthesupportbracetoensureitwillsupportthefullweightofthefanand

lightkit.

Step 4 - Install the Outlet Box

4-1.ObtainaUL-approvedoctagonal4”x1-1/2”outletbox,plustwo#8x1-1/2”

woodscrewsandwashers,availablefromanyhardwarestoreorelectricalsupply

house.

4-2.Orienttheoutletboxsothatboththeinnerandouterholesintheboxalign

withthejoistorsupportbrace.

4-3.Drillpilotholesnolargerthantheminordiameterofthewoodscrews(5/64”)

throughtheinnerholesoftheoutletbox.

4-4.Attachtheoutletboxdirectlytothesupportbraceorjoistwithtwo#8x1-1/2”

woodscrewsandwashers.ebottomoftheoutletboxmustberecesseda

minimumof1/16”intotheceiling.

Step 5 - Prepare the Wiring

5-1.Makesurethecircuitbreakerstothefansupplylineleadsandassociatedwall

switchlocationareturnedo.Ifyoucannotlockthecircuitbreakersinthe

oposition,securelyfastenaprominentwarningdevice,suchasatag,tothe

servicepanel.

5-2.readthefansupplylinethroughtheoutletboxsothatthefansupplyline

extendsatleast6”beyondthebox.

5-3.Attachthefansupplylinetotheoutletboxwithanapprovedconnector,

availableatanyhardwarestoreorelectricalsupplyhouse.

5-4.MakecertainthewiringmeetsallnationalandlocalstandardsandANSI/NFPA

70.

Youhavenowsuccessfullypreparedyourceilingfansite.Forinstructionstoinstall

yourceilingfan,gotoyourfanmanualandcontinuewithSection2 • Installing the

Ceiling Plate.

42409-01•06/17/10•HunterFanCompany

Installer’s Choice and Optional Accessories

Understanding Mounting and Installer’s Choice®

Hunter’spatented3-positionmountingsystemprovidesyoumaximum

installationexibilityandease.YoucaninstallyourHunterfaninone

ofthreeways,dependingonceilingheightandyourpreference:Low

Prole,Standard,orAnglemounting.estepsinthismanualinclude

instructionsforallthreeInstaller’sChoicemountingmethods.

Considering Optional Accessories

ConsiderusingHunter’soptionalaccessories,includingawall-mounted

orremotespeedcontrol.Toinstallandusetheaccessories,follow

theinstructionsincludedwitheachproduct.Forquietandoptimum

performanceofyourHunterfan,useonlyHunterspeedcontrols.

Forceilingshigherthan8feet,youcanpurchase

Hunterextensiondownrods.AllHunterfansuse

sturdy3/4”diameterpipetoassurestabilityand

wobble-freeperformance.

Standard Mountinghangsfromthe

ceilingbyadownrod(included).

Angle Mountingrecommendedfora

vaultedorangledceiling

SupportBrace

Standard

Mounting

Style

Ceiling

OutletBox

SupportBrace

Ceiling

OutletBox

Angle

Mounting

Style

Low Proﬁle Mountingtsclosetothe

ceiling,recommendedforceilingsless

than8feethigh

SupportBrace

LowProle

Mounting

Style

Ceiling

OutletBox

42409-01•06/17/10•HunterFanCompany

1 • Getting Ready

Toinstallaceilingfan,besureyoucandothefollowing:

•Locatetheceilingjoistorothersuitablesupportinceiling.

•Drillholesforandinstallwoodscrews.

•Identifyandconnectelectricalwires.

•Lift40pounds.

Ifyouneedhelpinstallingthefan,yourHunterfandealercandirect

youtoalicensedinstallerorelectrician.

Gathering the Tools

Youwillneedthefollowingtoolsforinstallingthefan:

•Electricdrillwith9/64”bit

•Standardscrewdriver(magnetictiprecommended)

•Phillips-headscrewdriver(magnetictiprecommended)

•Wrenchorpliers

•Ladder(heightdependentuponinstallationsite)

Checking Your Fan Parts

Carefullyunpackyourfantoavoiddamagetothefanparts.Referto

theincludedPartsGuide.Checkforanyshippingdamagetothemotor

orfanblades.Ifanypartsaremissingordamaged,contactyourHunter

dealerorcallHunterTechnicalSupportDepartmentat866-268-1936.

Installing Multiple Fans?

Ifyouareinstallingmorethan

onefan,keepthefanbladesand

bladeirons(ifapplicable)insets,

astheywereshipped.

42409-01•06/17/10•HunterFanCompany

2 • Installing the Ceiling Plate

CAUTION: Toavoidpossibleelectricalshock,beforeinstallingyourfan,

disconnectthepowerbyturningothecircuitbreakerstotheoutletbox

andassociatedwallswitchlocation.Ifyoucannotlockthecircuitbreakers

intheoposition,securelyfastenaprominentwarningdevice,suchasa

tag,totheservicepanel.

2-1. Drilltwopilotholesintothewoodsupportstructurethroughthe

outermostholesintheoutletbox.epilotholesshouldbe9/64”

indiameter.

2-2.Yourfancomeswithtwoneoprenenoiseisolators(“Isolators”).

Positiontheisolatorsbetweentheceilingplateandceilingby

insertingtheraisedareasoneachisolatorintotheholesinthe

ceilingplate.

2-3. readtheleadwiresfromtheoutletboxdownthroughthehole

inthemiddleoftheceilingplate.

2-4. Aligntheslottedholesintheceilingplatewiththepilotholesyou

drilledinthewoodsupportstructure.Forproperalignmentuse

slottedholesdirectlyacrossfromeachother.

Note:eisolatorsshouldbeushagainsttheceiling.

2-5. Placeaatwasheroneachofthetwo3”woodscrewsandpass

thescrewsthroughtheslottedholesintheceilingplateintothe

pilotholesyoudrilled.

  Tightenthescrewsintothe9/64”pilotholes;donotuselubricants

onthescrews.Donotovertighten.

FlatWasher

3”WoodScrew

Step 2-2

Steps 2-3 – 2-5

For Angled Ceilings:Besuretoorient

theceilingplatesothatthetwotabs

arepointingtowardstheceilingpeak.

Ceiling

Plate

Towards

CeilingPeak

Isolator

42409-01•06/17/10•HunterFanCompany

3 • Assembling and Hanging the Fan

WARNING:Fanmayfallifnotassembledasdirectedinthese

installationinstructions.

3-1.Unbundlethewiresfromthefan.

For Standard or Angle mounting:

3-2.Toassemblefantohangdownfromaatorangledceiling,insert

thedownrodthroughthecanopyandcanopytrimring.Feedthe

wiresfromthefanthroughthedownrod.

3-3.Loosenthesquareheadsetscrewontheadaptertoinstallthe

downrod.Note:Whenthedownrodisfullyinstalled,2-3threads

onthepipewillstillbevisible;thisisnormal.Securelyretighten

thesetscrewwithawrenchorpliers.SkiptoStep3-6.

CAUTION:eadapterhasaspecialcoatingonthethreads.Do

notremovethiscoating;thecoatingpreventsthedownrodfrom

unscrewing.Onceassembled,donotremovethedownrod.

For Low Proﬁle mounting:

Note:Forlowprolemounting,thedownrodisreplacedwiththe

lowprolewasher.

3-4.Placethelowprolewasherintothecanopy.Besurethegreen

groundwireispointinguptowardtheceiling.

3-5.Aligntheholesinthewasherwiththeholesintheadapter.

Assemblesecurelywiththreelowprolescrews.

3-6.Raisethefanandaligntheslotsinthecanopywiththetabsonthe

ceilingplate.

Steps 3-4 – 3-5

LowProle

Washer

LowProleScrew

Step 3-6

CanopySlots

Ceiling

Plate

Tabs

Steps 3-2 – 3-3

Downrod

Canopy

SetScrew

Canopy

Trim

Ring

42409-01•06/17/10•HunterFanCompany

4 • Securing Fan to Secondary Support System

4-1.Findtheloopedendofthebraidedcableandinsertitthroughthe

ceilingplateandoneoftheholesintheoutletboxintotheceiling.

4-2.Accessthesupportbraceintheceiling.Youmaynotbeabletodo

thisfrombelowtheceilingdependingonyourinstallationsite.

4-3.Drivea#10x38mm(1-1/2”)woodscrewandwasherintotheside

ofthebracethatholdstheoutletbox.Leave3mm(1/8”)ofspace

betweenthesupportbraceandthewasher.

4-4.Wrapthebraidedcablearoundthesupportbraceoncecreatinga

completecircle.

4-5.Hooktheloopedendofthecableoverthewoodscrewsothatthe

braidedcableliesbetweenthewasherandthesupportbrace.

4-6.Tightentheloopandsecurethescrewandwasheralltheway

downtothesupportbrace.

4-7.Coiluptheexcesscable.

4-8.Returntothefansoyoucancompletethefanwiring.

Step 4-1

3mm (1/8")

Steps 4-2 – 4-3

Steps 4-4 – 4-5

Steps 4-6 – 4-7

Support

Brace

Ceiling

OutletBox

Braided

Cable

42409-01•06/17/10•HunterFanCompany

5 • Wiring the Fan

Single Switch Wiring

Dual Switch Wiring

Wire

Connector

All wiring must be in accordance with national and local electrical

codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a

qualiﬁed electrician.

Wallswitchesarenotincluded.Selectanacceptablegeneral-useswitch

inaccordancewithnationalandlocalelectricalcodes.

5-1. Beforeattemptinginstallation,makesurethepowerisstillo.

5-2. Toconnectthewires,holdthebaremetalleadstogetherandplace

awirenutoverthem,thentwistclockwiseuntiltight.Forallthese

connectionsusethewireconnectorsprovided.

5-3. Connectthebareorgreengroundwire(grounded)fromthe

ceilingtothegreengroundwire(grounded)fromtheceilingplate

andthegreengroundwirefromthefan.

5-4. Connectthewhitewire(ungrounded)fromtheceilingtothe

whitewire(ungrounded)fromthefan.

5-5. Connecttheremainingwiresasfollows:

Dual Switch Wiring:

•eblackwire(ungrounded)fromtheceilingtotheblackwire

(ungrounded)fromthefan

•eblack/whitewire(ungrounded)fromthefantothewire

(ungrounded)forthewallswitch

Single Switch Wiring:

•eblackwire(ungrounded)fromtheceilingtotheblack

(ungrounded)andtheblack/whitewire(ungrounded)from

thefan

CAUTION:Besurenobarewireorwirestrandsarevisibleafter

makingconnections.

5-6. Turnthesplicesupwardandpushthemcarefullybackthroughthe

ceilingplateintotheoutletbox.

5-7. Spreadthewiresapart,withthegroundedwiresononesideof

theoutletboxandtheungroundedwiresontheothersideofthe

outletbox.

42409-01•06/17/10•HunterFanCompany

6 • Installing the Canopy and Canopy Trim Ring

6-1.Rotatethehangerballsothetabinthecanopyissecureinthe

grooveinthehangerball.

WARNING:Failuretocompletethisstepcouldcausefantofall.

6-2. Liftthefanandalignthecanopyscrewholeswiththemounting

holesontheceilingplate.

6-3. Partiallyinstallacanopyscrewintothesideoppositetheceiling

platetabs.

6-4. Partiallyinstallanothercanopyscrewintotheholebetweenthe

twoceilingplatetabs.Securelytightenbothscrews.

6-5. Usingbothhands,pushthecanopytrimringuptothetopofthe

canopy.ecanopytrimringwillsnapandlockintoplace.

Step 6-1

Step 6-2

Groove

Tab

Step 6-3 Step 6-4

Should you need to remove the canopy

trim ring, follow these steps:

 1.Locatethetabindicators,small

bumpsontopoftabs.

 2.Pressrmlyonoppositesidesofthe

ringtowardsthecanopy.etabs

willexoutreleasingthetrimring

fromthecanopy.

Step 6-5

42409-01•06/17/10•HunterFanCompany

7 • Assembling the Blades

Hunterfansuseseveralstylesoffanbladeirons(bracketsthatholdthe

bladetothefan).

7-1. Yourfanmayincludebladegrommets.Ifyourfanhasgrommets,

insertthembyhandintotheholesontheblades.

7-2. Attacheachbladetoabladeironusingthreebladeassembly

screws.Ifyouusedgrommets,thebladesmayappearslightlyloose

afterscrewsaretightened.isisnormal.

7-3. Someblademountingscrewsareinstalledinthemotortosecure

theshippingblocks.Removetheblademountingscrewsand

shippingblocksfromthemotor.Savethescrewsanddiscardthe

shippingblocks.

7-4. Foreachblade,insertoneblademountingscrewthroughthe

bladeiron,partiallyattachingthebladetothefan.Insertthe

secondblademountingscrew,thensecurelytightenboth

mountingscrews.

Step 7-1 (Detail)

Grommet

BladeAssembly

Screws

Usewithgrommet

Usewithoutgrommet

BladeMounting

Screw

Steps 7-1 – 7-2

Step 7-4

42409-01•06/17/10•HunterFanCompany

8 • Completing Your Installation With or Without a Light Fixture

YourHunterfancomeswithanintegratedlightxtureassemblyandan

optionalswitchhousingcapandplugbutton.isfeaturegivesyouthe

optionofinstallingthefanwithORwithouttheincludedlightxture.

estepsbelowdirectyouwhetherornotyouareinstallingalight

xture.

WARNING:Useonlythelightxturesuppliedwiththisfanmodel.

8-1. Toattachtheupperswitchhousing,partiallyinstalltwohousing

assemblyscrewsintotheswitchhousingmountingplate.

8-2. Feedtheupperplugconnectorthroughthecenteropeningofthe

housing.

8-3. Alignthekeyholeslotsinthehousingwiththehousingassembly

screws.

8-4. Turnthehousingcounterclockwiseuntilthehousingassembly

screwsarermlysituatedinthenarrowendofthekeyholeslots.

Installtheremainingscrewintothehousing.Tightenallthree

screwsrmly.

CAUTION:Makesuretheupperswitchhousingissecurely

attachedtotheswitchhousingmountingplate.Failuretoproperly

attachandtightenallthreeassemblyscrewscouldresultinthe

switchhousingandlightxturefalling.

8-5. If you want to install the light ﬁxture,proceedwithstep8-6

now.

If you do not want to install the light ﬁxture,youneedto

uninstallitnow.See“UninstallingtheLightFixture”onpage13.

Onceyouhaveuninstalledthelightxture,continuewithstep

8-6.

Steps 8-1 – 8-3

Housing

Assembly

Screw

Upper

Switch

Housing

Step 8-4

42409-01•06/17/10•HunterFanCompany

LowerSwitch

Housing

Plug

Connector

Housing

AssemblyScrew

Plug

Connector

Detail

Steps 8-6 – 8-7

8-6. Toattachthelowerswitchhousing,connecttheupperplug

connectorfromthemotortothelowerplugconnectorinthe

lowerswitchhousingassembly.

Note:Bothplugconnectorsarepolarizedandwillonlyttogether

oneway.Makesuretheconnectorsareproperlyalignedbefore

connectingthem.Incorrectconnectioncouldcauseimproper

operationanddamagetotheproduct.

8-7. Placethelowerswitchhousingassemblyovertheupperswitch

housing.Alignthesidescrewholesintheupperandlowerswitch

housings.Attachthelowerswitchhousingtotheupperswitch

housingwiththreehousingassemblyscrews.

If you are not installing the light ﬁxture, your installation is

complete. Otherwise,proceedwithstep8-8.

8-8. elastinstallationstepwheninstallingthelightxtureisto

installtheglassbowl.See“InstallingtheGlassBowl”onpage14for

instructions.

8 • Completing Your Installation With or Without a Light Fixture (Continued)

42409-01•06/17/10•HunterFanCompany

Uninstalling the Light Fixture

1. Touninstallthelightxture,rstdisconnecttheplugconnectors

betweentheblackwireandtheblack/whitewire.

2. Disconnecttheplugconnectorsbetweenthetwowhite

wires.

3. Uninstallthenutandwasherfromtheendofthelight

xtureinsidethelowerswitchhousing.

4. Unscrewthethreadedrodofthelightxturefromthe

lowerswitchhousing.

5. Removethelightxturefromthelowerswitchhousing

pullingdisconnectedwiresthroughtheholeinthecenterof

thelowerswitchhousing.

Note:Whenremovingthewires,pullthethinplug

connector(male)throughrst,andthenpulltheotherplug

connector(female)throughthehole.

6. Installthedummyterminals(includedinthesackparts)on

thetwodisconnectedwiresinthelowerswitchhousing.

7. Installtheswitchhousingcapandplugbuttontothelower

switchhousing.

LowerSwitch

Housing

readedRod

Steps 3 – 5

MaleDummy

Terminal

FemaleDummy

Terminal

Step 7

Cap

PlugButton

42409-01•06/17/10•HunterFanCompany

Installing the Glass Bowl

1. Firstinstalltwomediumbaseincandescentbulbs.

2. Attachtheextrapullchain(included)tothefanpullchainusingthe

plasticbreakawayconnector.(Youmayndtheplasticbreakaway

connectorontheendoftheextrachain.)

3. readthefanpullchainthroughtheholeinthemetaldisk.en,

threadthefanpullchainthroughtheholeinthecenteroftheglassbowl.

4. readthelightpullchainthroughtheholeinthecenterofthe

glassbowl.

5. Placethetwigupagainsttheglassbowl.

6. readthelightpullchainthroughthetwigandnialandscrewthe

nialontothethreadedrodenduntiltight.

forLightBulbs

(60WattMaximum)

MetalRod

MetalDisk

PullChain

GlassBowl

Finial

Breakaway

Connector

8 • Completing Your Installation With or Without a Light Fixture (Continued)

42409-01•06/17/10•HunterFanCompany

9-1. Turnonelectricalpowertothefan.

9-2. efanpullchaincontrolspowertothefan.epullchainhas

foursettingsinsequence:High,Medium,LowandO.

• Pullthechainslowlytochangesettings.

• Releaseslowlytopreventthechainfromrecoilingintothe

blades.

• echainusesabreakawayconnectorthatseparatesifthe

chainisjerked.Ifthishappens,simplyreinsertthechaininto

theconnector.

9-3. elightpullchaincontrolspowertothelight.epullchainhas

twosettings:OnandO.

9-4. Ceilingfansworkbestbyblowingairdownward(counterclockwise

bladerotation)inwarmweathertocooltheroomwithadirect

breeze.Incoldweather,havingthefandrawairupward(clockwise

bladerotation)willdistributethewarmerairtrappedatthe

ceilingaroundtheroomwithoutcausingadraft.

9-5. Forcleaningnishes,useasoftbrushorlint-freeclothtoprevent

scratching.Avacuumcleanerbrushnozzlecanremoveheavier

dust.Removesurfacesmudgesoraccumulateddirtanddustusing

amilddetergentandaslightlydampenedcloth.Youmayuse

anartisticagent,butneverabrasivecleaningagentsastheywill

damagethenish.

9-6. Cleanwoodnishbladeswithafurniturepolishingcloth.

Occasionally,applyalightcoatoffurniturepolishforadded

protectionandbeauty.Cleanpaintedandhigh-glossbladesinthe

samemannerasthefannish.

To Change Airﬂow Direction

Turnthefanoandletitcometoacomplete

stop.Slidethereversingswitchonthefantothe

oppositeposition.Restartfan.

In warm weather,use

downwardairowpattern

In cold weather,useupward

airowpattern

9 • Operating and Cleaning Your Ceiling Fan

Reversing

Switch

42409-01•06/17/10•HunterFanCompany

10 • Troubleshooting

Problem: Nothing happens; fan does not move.

1.Turnpoweron,replacefuse,orresetbreaker.

2.Loosencanopy,checkallconnectionsaccordingtothewiringthefansection.

3.Checktheplugconnectionintheswitchhousing.

4.Pushmotorreversingswitchrmlyleftorrighttoensurethattheswitchisengaged.

5.Pullthepullchaintoensureitison.

6.Removetheshippingblocks.

Problem: Noisy operation.

1.Tightenthebladebracketscrewsuntilsnug.

2.Tightenthebladescrewsuntilsnug.

3.Checktoseeifthebladeiscracked.Ifso,replacealltheblades.

4.Changetoanapprovedspeedcontrol.

5.Besurethattheglassissecure.

6.Checkandtightenthescrewsintheswitchhousingmountingplateandintheupperandlowerswitchhousing.

Problem: Excessive wobbling.

1.Ifyourfanwobbleswhenoperating,usetheenclosedbalancingkitandinstructionstobalancethefan.

2.Tightenallbladeand/orbladeironscrews.

3.Turnpowero,supportfanverycarefully,andcheckthatthehangerballisproperlyseated.

Ifyouneedpartsorserviceassistance,pleasecall

888-830-1326(InCanada,call866-268-1936)or

visitusatourwebsiteat

http://www.hunterfan.com.

HunterFanCompany

7130GoodlettFarmsParkway#400

Memphis,Tennessee38016

Hunter Fan 27543 Owner's manual

Brand: Hunter Fan

Model: 27543

Category: Household fans

Type: Owner's manual

Download PDF

report

Hunter Fan 27543 Owner's manual

Hunter Fan 27543 Owner's manual

Related papers

Other documents