Simer 2960 Owner's manual

Brand: Simer

Model: 2960

Category: Sanitary ware

Type: Owner's manual

Installation/Operation/Parts

For further operating, installation,

or maintenance assistance:

Call 1-800-468-7867

English . . . . . . . . . . . . . . Pages 2-5

Installation/Fonctionnement/Pièces

Pour plus de renseignements

concernant l’utilisation,

l’installation ou l’entretien,

Composer le

1 (800) 468-7867

Français . . . . . . . . . . . . Pages 6-9

Instalación/Operación/Piezas

Para mayor información sobre el

funcionamiento, instalación o

mantenimiento de la bomba:

Llame al 1-800-468-7867

Español . . . . . . . . . .Paginas 10-13

OWNER’S MANUAL

Submersible Sump Pumps

NOTICE D’UTILISATION

Pompes submersibles

pour puisard

MANUAL DEL USUARIO

Bombas sumergibles para

sumideros y Efluentes

Mod. 2925, 2960, 2985

293 Wright St., Delavan, WI 53115

Phone:

1-800-468-7867

1-800-546-7867

Fax:

1-800-390-5351

Safety / General Information 2

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

READ AND FOLLOW

SAFETY INSTRUCTIONS!

This is the safety alert symbol. When you see this

symbol on your pump or in this manual, look for

one of the following signal words and be alert to the

potential for personal injury.

warns about hazards that will cause serious

personal injury, death or major property damage if

ignored.

warns about hazards that can cause serious

personal injury, death or major property damage if

ignored.

warns about hazards that will or can cause

minor personal injury or property damage if ignored.

The label NOTICE indicates special instructions which

are important but not related to hazards.

Carefully read and follow all safety instructions in this

manual and on pump.

Keep safety labels in good condition.

Replace missing or damaged safety labels.

DESCRIPTION

These Submersible Sump Pumps are designed for home

sumps. Units are equipped with a 3-prong grounding-

type power cord. Ball bearings on motor shaft never

need lubrication. Automatic reset thermal protection.

SPECIFICATIONS

Power supply required ................................115V, 60 HZ.

Motor duty .....................................................Intermittent

Liquid Temp. Range .......................32°F to 77°F(0°-25°C)

Individual Branch Circuit Required (minimum) ..15 Amps

Discharge Adapter:..............1-1/4" FNPT to 1-1/4” FBSPT

NOTICE: Not designed for applications involving salt

water or brine! Use with salt water or brine will void

warranty. Do not use in water where fish are present.

SIMER warrants to the original consumer purchaser (“Purchaser”) of its products

that they are free from defects in material or workmanship.

If within twelve (12) months from the date of the original consumer purchase

any such product shall prove to be defective, it shall be repaired or replaced at

SIMER’s option, subject to the terms and conditions set forth below. Your origi-

nal receipt of purchase is required to determine warranty eligibility.

Exceptions to the Twelve (12) Month Warranty

Five (5) Year Warranty:

If within five (5) years from original consumer purchase any Pre-Charge water

system tank shall prove to be defective, it shall be repaired or replaced at

SIMER’s option, subject to the terms and conditions set forth below.

General Terms and Conditions

Purchaser must pay all labor and shipping charges necessary to replace product

covered by this warranty. This warranty shall not apply to acts of God, nor shall

it apply to products which, in the sole judgement of SIMER, have been subject

to negligence, abuse, accident, misapplication, tampering, alteration; nor due

to improper installation, operation, maintenance or storage; nor to other than

normal application, use or service, including but not limited to, operational fail-

ures caused by corrosion, rust or other foreign materials in the system, or oper-

ation at pressures in excess of recommended maximums.

Requests for service under this warranty shall be made by returning the defec-

tive product to the Retail outlet or to SIMER as soon as possible after the dis-

covery of any alleged defect. SIMER will subsequently take corrective action as

promptly as reasonably possible. No requests for service under this warranty

will be accepted if received more than 30 days after the term of the warranty.

This warranty sets forth SIMER’s sole obligation and purchaser’s exclusive rem-

edy for defective products.

SIMER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR

CONTINGENT DAMAGES WHATSOEVER.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL

OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT

NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE

DURATION OF THE APPLICABLE EXPRESS WARRANTIES PROVIDED HEREIN.

Some states do not allow the exclusion or limitation of incidental or conse-

quential damages or limitations on how long an implied warranty lasts, so the

above limitations or exclusions may not apply to you. This warranty gives you

specific legal rights and you may also have other rights which vary from state

to state.

Simer Limited Warranty

SIMER • 293 Wright St. • Delavan, WI U.S.A. 53115

Phone: 1-800-468-7867 / 1-800-546-7867 • Fax: 1-800-390-5351

GPH (LPH) AT TOTAL FEET (M) No Flow

Motor 1 5 10 15 20 25 At Height

Model HP (.3 M) (1.5 M) (3 M) (4.6 M) (6.1 M) (7.6 M) Shown Below

2925 1/4 1,200 (4,542) 1,000 (3,785) 675 (2,555) 400 (1,514) – – 20’ (6.1 M)

2960 1/3 2,300 (8,706) 1,975 (7,476) 1,425 (5,394) 850 (3,218) 300 (1,136) – 22’ (6.7 M)

2985 1/2 3,000 (11,356) 2,500 (9,464) 1,900 (7,192) 1,320 (4,997) 750 (2,839) – 25’ (7.6 M)

PERFORMANCE

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

General Information / Installation 3

ELECTRICAL & SWITCH

SPECIFICATIONS

GENERAL SAFETY INFORMATION

Electrically powered sump pumps normally give many

years of trouble-free service when correctly installed,

maintained, and used. However, unusual circumstances

(interruption of power to the pump, dirt/debris in the

sump, flooding that exceeds the pump’s capacity, elec-

trical or mechanical failure in the pump, etc.) may pre-

vent your pump from functioning normally. To prevent

possible water damage due to flooding, consult your

retailer about a secondary AC sump pump, a DC backup

sump pump, and/or a high water alarm. See the

“Troubleshooting Chart” in this manual for information

about common sump pump problems and remedies. For

more information, see your retailer or call Simer cus-

tomer service at 1-800-468-7867.

1. Know the pump application, limitations, and poten-

tial hazards.

2. Disconnect power before servicing.

3. Release all pressure within system before servicing

any component.

4. Drain all water from system before servicing.

5. Secure discharge line before starting pump. An unse-

cured discharge line will whip, possibly causing per-

sonal injury and/or property damage.

6. Check hoses for a weak or worn condition before

each use, making certain that all connections are

secure.

7. Periodically inspect sump, pump and system compo-

nents. Keep free of debris and foreign objects.

Perform routine maintenance as required.

8. Provide a means of pressure relief for pumps whose

discharge line can be shut-off or obstructed.

9. Personal Safety:

a. Wear safety glasses at all times when working

with pumps.

b. Keep work area clean, uncluttered and properly

lighted – replace all unused tools and equipment.

c. Keep visitors at a safe distance from work area.

d. Make workshop child-proof – with padlocks, mas-

ter switches, and by removing starter keys.

10.When wiring an electrically driven pump, follow all

electrical and safety codes that apply.

11. This equipment is only for use on 115 volt (single

phase) and is equipped with an approved 3-conduc-

tor cord and 3-prong, grounding-type plug.

Risk of electrick shock. Can burn or

kill. To reduce risk of electric shock, pull plug before

servicing.

Pump is supplied with a grounding conductor and

grounding-type attachment plug. Be sure it is con-

nected only to a properly grounded grounding-type

receptacle.

Where a 2-prong wall receptacle is encountered, it

must be replaced with properly grounded 3-prong

receptacle installed in accordance with codes and

ordinances that apply.

12. All wiring should be performed by a qualified

electrician.

13.Make certain power source conforms to require-

ments of your equipment.

14.Protect electrical cord from sharp objects, hot sur-

faces, oil, and chemicals. Avoid kinking cord. Replace

or repair damaged or worn cords immediately.

15.Do not touch an operating motor. Modern motors

are designed to operate at high temperatures.

16.Do not handle pump or pump motor with wet hands

or when standing on wet or damp surface, or in

water.

Risk of electrick shock. Can burn or kill. If

your basement has water or moisture on floor, do not

walk on wet area until all power has been turned off. If

shut-off box is in basement, call electric company or

hydro authority to shut-off service to house, or call your

local fire department for instructions. Remove pump and

replace it. Failure to follow this warning can result in

fatal electrical shock.

17.Do not use this pump in water where fish are present.

18.This pump has not been investigated for use in

swimming pool areas.

Oil on the pump or in the sump may indicate motor

leakage and an electrical shock hazard. Turn off power

and check pump for oil leakage from impeller area.

Replace pump if it leaks.

INSTALLATION

1. Install pump in a sump pit with a minimum diameter

of 14" (356mm). Sump depth should be 18"

(457mm). Construct sump pit of tile, concrete, steel

or plastic. Check local codes for approved materials.

2. Install pump in pit so that switch operating mecha-

nism has maximum possible clearance.

3. Pump should not be installed on clay, earth or sand

surfaces. Clean sump pit of small stones and gravel

which could clog pump. Keep pump inlet screen clear.

NOTICE: Do not use ordinary pipe joint compound

on plastic pipe. Pipe joint compound can attack

plastics.

Motor Individual *Switch Setting

Motor Full Load Branch Circuit in inches (mm)

Series HP Amps Req. (Amps)

On Off

2925 1/4 1.5 15 11"(279) 5"(127)

2960 1/3 2.6 15 11"(279) 5"(127)

2985 1/2 3.0 15 11"(279) 5"(127)

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

Installation / Operation 4

4. Install an in-line check valve to prevent flow back-

wards through pump when pump shuts off.

NOTICE: Drill a 1/8" (3.2 mm) hole in discharge pipe

just above pump body but below check valve to pre-

vent air locks.

5. Install discharge plumbing. A 1-1/4” FNPT to 1-1/4”

FBSPT adapter is included with the pump. Use rigid

plastic pipe and wrap threads with Teflon tape. Screw

pipe into pump hand tight +1 – 1-1/2 turns.

Risk of flooding. If a flexible discharge

hose is used, make sure pump is secured in sump to

prevent movement. Failure to secure pump may

allow pump movement, switch interference and pre-

vent pump from starting or stopping.

6. To reduce motor noise and vibrations, a short length

of rubber hose (1-7/8" (47.6mm) I.D., e.g. radiator

hose) can be connected into discharge line near

pump using suitable clamps.

7. Power Supply: Pump is designed for 115 V., 60 Hz.,

operation and requires a minimum 15 amp individual

branch circuit. Both pump and switch are supplied

with 3-wire cord sets with grounding-type plugs.

Switch plug is inserted directly into outlet and pump

plug inserts into opposite end of switch plug.

Hazardous voltage. Can shock, burn or

kill. Pump should always be electrically grounded to

a suitable electrical ground such as a grounded water

pipe or a properly grounded metallic raceway, or

ground wire system. Do not cut off ground pin.

8. If pump discharge line is exposed to outside sub-

freezing atmosphere, portion of line exposed must be

installed so any water remaining in pipe will drain to

the outfall by gravity. Failure to do this can cause

water trapped in discharge line to freeze which could

result in damage to pump.

9. After piping and check valve have been installed, unit

is ready for operation.

10.Check operation by filling sump with water and

observing pump operation through one complete

cycle.

Risk of flooding. Failure to make this

operational check may lead to improper operation,

premature failure, and flooding.

OPERATION

Risk of electrick shock. Can burn or kill.

Before attempting to check why unit has stopped operat-

ing, disconnect power from unit. Do not handle a pump

or pump motor with wet hands or when standing on wet

or damp surface, or in water.

1. Shaft seal depends on water for lubrication. Do not

operate pump unless it is submerged in water as seal

may be damaged if allowed to run dry.

2. Motor is equipped with an automatic reset thermal

protector. If temperature in motor should rise unduly,

switch will cut off all power before damage can be

done to motor. When motor has cooled sufficiently,

switch will reset automatically and restart motor. If

protector trips repeatedly, pump should be removed

and checked as to cause of difficulty. Low voltage,

extension cords, clogged impeller, very low head or

lift, etc., could cause cycling.

3. Pump will not remove all water.

4.5"

Tether

Length

Float Switch Tether Length:

NOTICE: Do not change tether length of float switch. Float

must swing through its complete arc without interference.

Troubleshooting 5

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

SYMPTOM PROBABLE CAUSE(S) CORRECTIVE ACTION

Pump won’t start or run. Blown fuse. If blown, replace with fuse of proper size.

Low line voltage. If voltage under recommended minimum, check size of wiring from

main switch on property. If OK, contact power company or hydro

authority.

Defective motor. Replace pump.

Defective float switch. Replace pump.

Float obstructed. Remove obstruction.

Pump starts and stops Backflow of water from piping. Install or replace check-valve.

too often.

Faulty float switch. Replace pump.

Pump won’t shut off. Defective float switch. Replace pump.

Restricted discharge Remove pump and clean pump and piping.

(obstacle in piping).

Float obstructed. Remove obstruction.

Pump operates but Low line voltage. If voltage under recommended minimum, check size of wiring from

delivers little or main switch on property. If OK, contact power company or hydro

no water. authority.

Something caught in impeller. Replace pump.

Worn or defective parts or Replace pump.

plugged impeller.

Check valve installed without Drill a 1/16" - 1/8" (1.6mm - 3.2mm) dia. hole in the discharge pipe

vent hole. between the pump discharge port & the check valve.

NOTICE: These pumps have no serviceable parts inside case. Opening case will ruin pump. For obstructions or block-

ages of the impeller replace the pump.

Hazardous voltage. Can shock, burn or kill. Unplug pump before attempting to clean or work on pump.

Page is loading ...

Simer 2960 Owner's manual

Brand: Simer

Model: 2960

Category: Sanitary ware

Type: Owner's manual

Download PDF

report

in other languages

français: Simer 2960 Le manuel du propriétaire
español: Simer 2960 El manual del propietario

Simer 2960 Owner's manual

Simer 2960 Owner's manual

in other languages

Related papers

Other documents