Craftsman 917.20380 User manual

Brand: Craftsman

Model: 917.20380

Category: Lawnmowers

Type: User manual

Operator's Manual

ICRAFTSMnN°I

GA TRACTO

19.0 HR* 42" Mower

Electric Start

6-Speed Transaxle

Model No.

917.20380

, EspaSol, p. 32

[[_ his product has a low emission engine which operates

differently from previously built engines. Before you start the

engine, read and understand this manual.

IMPORTANT:

Read and follow all Safety

Rules and instructions before

operating this equipment.

For answers to your questions

about this product, call:

1-888-331-4569

Craftsman Customer Help Line

Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsmanwebsite: www.craftsman.com

* The power rating as declared by the engine manufacturer is the

average gross power output at the specified RPM of a typical

production engine for the engine model measured using SAE

Standards for engine gross powen Please refer to the engine

manufacturer for details,

* La potencia nominal declarada por el fabricante del motor es la

safida media de potencia bruta a las RPM especificadas de un

motor de serie tipico para el modelo de motor, medida segt_n

las normas SAE sobre potencia bruta de motor. Para mas

informaci6n, consulte al fabricante del moton

586066027 Rev. 2

Warranty .................................................. 2

Safety Rules ............................................ 3

Product Specifications ............................. 6

Assembty/Pre-Operation ......................... 7

Operation ................................................. 9

Maintenance .......................................... 15

Maintenance Schedule .......................... 15

Service and Adjustments ....................... 20

Storage .................................................. 26

Troubleshooting ..................................... 27

Sears Service .......................... Back Cover

CRAFTSMAN FULL WARRANTY

FOR TWO YEARS from the date of purchase, all non-expendable parts of this riding equipment are

warranted against any defects in material or workmanship. A defective non-expendable part will receive

free in-home repair or replacement if repair is unavailable.

BATTERY LIMITED WARRANTY

FOR 90 DAYS from the date of purchase, the battery (an expendable part) of this riding equipment is

warranted against any defects in material or workmanship. A new battery will be supplied free of charge.

You are responsible for the labor cost of battery installation.

ADDITIONAL LIMITED WARRANTmES

In the following additional warranties, you are responsible for the labor cost of part installation after

the second year from the date of purchase.

FOR FIVE YEARS from the date of purchase, the frame of this riding equipment is warranted against any

defects in material or workmanship. A new frame will be supplied free of charge.

FOR TEN YEARS from the date of purchase, the front axle of this riding equipment is warranted against any

defects in material or workmanship. A new front axle will be supplied free of charge.

FOR AS LONG AS IT IS USED by the original owner after the tenth year from the date of purchase, the

cast iron front axle (if equipped) of this riding equipment is warranted against any defects in material or

workmanship. With proof of purchase, a new cast iron front axle will be supplied free of charge.

WARRANTY SERVICE

For warranty coverage details to obtain free repair or replacement, call 1-888-331-4569 or visit the web

page: www.craftsman.com/warranty

In all cases above, if part repair or replacement is impossible, the riding equipment will be replaced free of

charge with the same or an equivalent model.

All of the above warranty coverage is void if this riding equipment is ever used while providing commercial

services or if rented to another person.

This warranty covers ONLY defects in material and workmanship. Warranty coverage does NOT

include:

• Expendable parts (except battery) that can wear out from normal use within the warranty period, including

but not limited to blades, spark plugs, air cleaners, belts, and oil filters.

• Standard maintenance servicing, oil changes, or tune-ups.

• Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps, or

glass.

• Tire or wheel replacement or repair resulting from normal wear, accident, or improper operation or

maintenance.

• Repairs necessary because of operator abuse, including but not limited to damage caused by towing

objects beyond the capability of the riding equipment, impacting objects that bend the frame, axle

assembly or crankshaft, or over-speeding the engine.

• Repairs necessary because of operator negligence, including but not limited to, electrical and mechanical

damage caused by improper storage, failure to use the proper grade and amount of engine oil, failure

to keep the deck clear of flammable debris, or failure to maintain the riding equipment according to the

instructions contained in the operator's manual.

• Engine (fuel system) cleaning or repairs caused by fuel determined to be contaminated or oxidized

(stale). In general, fuel should be used within 30 days of its purchase date.

• Normal deterioration and wear of the exterior finishes, or product label replacement.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to

state.

Sears Brands Management Corporation, Hoffman Estates, IL 60179

_DANGER: This cutting machine is capable of amputating hands and feet and

throwing objects. Failure to observe the following safety instructions could result

in serious injury or death.

_IWARNING: In orderto preventacciden-

tat starting when setting up, transporting,

adjusting or making repairs, always discon-

nect spark plug wire and place wire where

it cannot contact spark plug.

_IWARNING: Do not coast down a hill in

neutral, you may lose control of the tractor.

_IWARNING: Tow only the attachments

that are recommended by and comply with

specifications of the manufacturer of your

tractor. Use common sense when towing.

Operate only at the lowest possible speed

when on a slope. Too heavy of a load, while

on a slope, is dangerous. Tires can lose

traction with the ground and cause you to

lose control of your tractor.

_IWARNING: Engine exhaust, some of

its constituents, and certain vehicle compo-

nents contain or emit chemicals known to

the State of California to cause cancer and

birth defects or other reproductive harm.

_IWARNING: Battery posts, terminals and

related accessories contain lead and lead

compounds, chemicals known to the State of

California to cause cancer and birth defects

or other reproductive harm. Wash hands

after handling.

I. GENERAL OPERATION

* Read, understand, and follow all instruc-

tions on the machine and in the manual

before starting.

Do not put hands or feet near rotating

parts or under the machine. Keep clear

of the discharge opening at all times.

. Only allow responsible adults, who are

familiar with the instructions, to operate

the machine.

. Clear the area of objects such as rocks,

toys, wire, etc., which could be picked

up and thrown by the blades.

Be sure the area is clear of bystanders

before operating. Stop machine ifanyone

enters the area.

Never carry passengers.

. Do not mow in reverse unless absolutely

necessary. Always took down and behind

before and while backing.

Never direct discharged material toward

anyone. Avoid discharging material

against a wall or obstruction. Material

may ricochet back toward the operator.

Stop the blades when crossing gravel

surfaces.

Do not operate machine without the en-

tire grass catcher, discharge chute, or

other safety devices inplace and working.

• Slow down before turning.

Never leave a running machine unat-

tended. Always turn off blades, set

parking brake, stop engine, and remove

keys before dismounting.

Disengage blades when not mowing.

Shut off engine and wait for all parts to

come to a complete stop before cleaning

the machine, removing the grass catcher,

or unclogging the discharge chute.

• Operate machine only in daylight or good

artificial light.

Do not operate the machine while under

the influence of alcohol or drugs.

• Watch for traffic when operating near or

crossing roadways.

• Use extra care when loading or unloading

the machine into a trailer or truck.

Always wear eye protection when operat-

ing machine.

Use ear protectors to avoid damage to

hearing.

Data indicates that operators, age 60

years and above, are involved in a large

percentage of riding mower-related inju-

ries. These operators should evaluate

their ability to operate the riding mower

safely enough to protect themselves and

others from serious injury.

Follow the manufacturer's recommenda-

tion for wheel weights or counterweights.

Keep machine free of grass, leaves or

other debris build-up which can touch hot

exhaust/engine parts and burn. Do not

allow the mower to plow leaves or other

debris which can cause build-up to oc-

cur. Clean any oil or fuel spillage before

operating or storing the machine. Allow

machine to cool before storage.

il. SLOPE OPERATION

Slopes are a major factor related to loss of

control and tip-over accidents, which can

result in severe injury or death. Operation

on all slopes requires extra caution. If you

cannot back up the slope or ifyou feel uneasy

on it, do not mow it.

• Mow up and down slopes, not across.

• Watch for holes, ruts, bumps, rocks, or

other hidden objects. Uneven terrain

could overturn the machine. Tall grass

can hide obstacles.

• Choose a low ground speed so that you

will not have to stop or shift while on the

slope.

• Do not mow on wet grass. Tires may lose

traction.

Always keep the machine in gear when

going down slopes. Do not shiftto neutral

and coast downhill.

• Avoid starting, stopping, or turning on a

slope. Ifthetires Iosetraction, disengage

the blades and proceed slowly straight

down the slope.

• Keep all movement on the slopes stow

and gradual. Do not make sudden

changes in speed or direction, which

could cause the machine to roll over.

• Use extra care while operating machine

with grass catchers or other attachments;

they can affect the stability of the ma-

chine. Do no use on steep slopes.

• Do not try to stabilize the machine by

putting your foot on the ground.

• Do not mow near drop-offs, ditches,

or embankments. The machine could

suddenly roll over if a wheel is over the

edge or if the edge caves in.

Ill. CHILDREN

_I, WARNING: CHILDREN CANBE INJURED

BYTHIS EQUIPMENT The American Acade-

my of Pediatrics recommends that children

be a minimum of 12 year of age before op-

erating a pedestrian controlled lawn mower

and a minimum of 16 years of age before

operating a riding lawn mower.

Tragic accidents can occur if the operator

is not alert to the presence of children.

Children are often attracted to the machine

and the mowing activity. Never assume

that children will remain where you last

saw them.

* Keep children out of the mowing area

and in the watchful care of a responsible

adult other than the operator.

* Be alert and turn machine off if a child

enters the area.

* Before and while backing, look behind

and down for small children.

* Never carrychildren, even withthe blades

shutoff. They may fatl offand beseriously

injured or interfere with safe machine

operation. Children who have been given

rides in the past may suddenly appear in

the mowing area for another ride and be

run over or backed over bythe machine.

* Never allow children to operate the ma-

chine.

* Use extra care when approaching blind

corners, shrubs, trees, or other objects

that may block your view of a child.

IV. TOWING

* Tow only with a machine that has ahitch

designed for towing. Do not attach towed

equipment except at the hitch point.

* Followthemanufacturer'srecommenda-

tion for weight limits for towed equipment

and towing on slopes.

. Never allow children or others in or on

towed equipment.

* On slopes, theweight ofthe towed equip-

ment may cause loss of traction and toss

of control.

* Travel slowly and allow extra distance to

stop.

V. SERVICE

SAFE HANDLING OF GASOLINE

To avoid personal injury or property dam-

age, use extreme care in handling gasoline.

Gasoline is extremely flammable and the

vapors are explosive.

. Extinguish all cigarettes, cigars, pipes,

and other sources of ignition.

. Use only approved gasoline container.

. Never remove gas cap or add fuel with

the engine running. Allow engine to cool

before refueling.

. Never fuel the machine indoors.

. Neverstorethe machine orfuelcontainer

where there is an open flame, spark, or

pilot light such as on a water heater or

other appliances.

. Never fill containers inside a vehicle or

on a truck or trailer bed with plastic liner.

Always place containers on the ground

away from your vehicle when filling.

• Removegas-poweredequipmentfrom

thetruckortrailerandrefuelitonthe

ground.Ifthisisnotpossible,thenrefuel

suchequipmentwithaportablecontainer,

ratherthanfromagasolinedispenser

nozzle.

Keepthenozzleincontactwiththerim

ofthefueltankorcontaineropeningat

alltimesuntilfuelingiscomplete.Donot

useanozzlelock-opendevice.

Iffuelisspilledonclothing,changecloth-

ingimmediately.

Neveroverfillfueltank.Replacegascap

andtightensecurely.

GENERALSERVICE

• Neveroperatemachineinaclosedarea.

Keepallnutsandboltstighttobesurethe

equipmentisinsafeworkingcondition.

Nevertamperwithsafetydevices.Check

theirproperoperationregularly.

Keepmachinefreeofgrass,leaves,or

otherdebrisbuild-up.Cleanoilorfuel

spillageandremoveanyfuel-soakedde-

bris.Allowmachinetocootbeforestoring.

Ifyoustrikeaforeignobject,stopand

inspectthemachine.Repair,ifnecessary,

beforerestarting.

Nevermakeanyadjustmentsorrepairs

withtheenginerunning.

Checkgrasscatchercomponentsandthe

dischargechutefrequentlyandreplace

withmanufacturer'srecommendedparts,

whennecessary.

Mowerbladesaresharp.Wraptheblade

orweargloves,anduseextracaution

whenservicingthem.

• Checkbrakeoperationfrequentty.Adjust

andserviceasrequired.

Maintainorreplacesafetyandinstruction

labels,asnecessary.

Besuretheareaisclearofbystanders

beforeoperating.Stopmachineifanyone

entersthearea.

• Nevercarrypassengers.

Donotmowinreverseunlessabsolutely

necessary.Alwaystookdownandbehind

beforeandwhilebacking.

Nevercarrychildren,evenwiththe

bladesshutoff.Theymayfalloffand

beseriouslyinjuredorinterferewithsafe

machineoperation.Childrenwhohave

beengivenridesinthepastmaysuddenly

appearinthemowingareaforanother

rideandberunoverorbackedoverby

themachine.

Keepchildrenoutofthemowingarea

andinthewatchfulcareofaresponsible

adultotherthantheoperator.

• Bealertandturnmachineoffifachild

entersthearea.

• Beforeandwhilebacking,tookbehind

anddownforsmallchildren.

Mowupanddownslopes(15°Max),not

across.

Choosealowgroundspeedsothatyou

willnothavetostoporshiftwhileonthe

slope.

Avoidstarting,stopping,orturningona

slope.Ifthetirestosetraction,disengage

thebladesandproceedslowlystraight

downtheslope.

• If machinestopswhilegoinguphill,

disengageblades,shiftintoreverseand

backdownslowly.

Donotturnonslopesunlessnecessary,

andthen,turnslowlyandgradually

downhill,ifpossible.

• WhenIoadingorunloadingthismachine,

donotexceedthemaximumrecom-

mendedoperationangleof15°.

PRODUCTSPECIFiCATiONS

Gasoline Capacity 2.5 Gallons/9,46 L

and type: Regular Unleaded *

Oil Type: SAE 30 (above 32°F/0°C

(API: SG-SL) SAE 5W30 (below 32°F/0°C

Oil Capacity: W/Filter: 56 Oz./1,65 L

W/out Filter: 48 Oz./1,4 L

Spark Plug: Champion RC12YC

(Gap: .030"/0,76 mm)

Charging 3 Amps Battery

System: 5 Amps Headlights

Battery: Amp/Hr: 28

Min. CCA: 230

Case size: U1R

Blade Bolt Torque: 45-55 Ft. Lbs./62-75 Nm

*_LGasoline containing up to 10% ethanol (El0) is

acceptable for use in this machine. The use of

any gasoline exceeding 10% ethanol (El0) will

void the product warranty.

CONGRATULATIONS on your purchase of

a new tractor. It has been designed, engi-

neered and manufactured to giveyou the best

possible dependability and performance.

Should you experience any problem you can-

not easily remedy, please contact a Sears or

other qualified service center. We have com-

petent, well-trained representatives and the

proper tools to service or repair this tractor.

Please read and retain this manual. The

instructions will enable you to assemble

and maintain your tractor properly. Always

observe the "SAFETY RULES".

CUSTOMER RESPONSIBILITIES

Read and observe the safety rules.

* Follow a regular schedule in maintaining,

caring for and using your tractor.

* Follow instructions under"Maintenance"

and "Storage" sections of this manual.

* Wear proper Personal Protective Equip-

ment (PPE) while operating this machine,

including (at a minimum) sturdy footwear,

eye protection, and hearing protection.

Do not mow in shorts and/or open toed

footwear.

Always let someone know you are outside

mowing.

_IWARNING" This tractor is equipped with

an internal combustion engine and should

not be used on or near any unimproved

forest-covered, brush-covered or grass-

covered land unless the engine's exhaust

system is equipped with a spark arrester

meeting applicable local or state laws (if

any). If a spark arrester is used, it should

be maintained in effective working order by

the operator.

Inthe state ofCalifornia the above is required

by law (Section 4442 of the California Public

Resources Code). Other states may have

similar laws. Federal laws apply on federal

lands. A spark arrester for the muffler is

available through your nearest Sears service

center (See REPAIR PARTS manual).

REPAIR PROTECTION AGREEMENTS

Congratulations on making a smart pur-

chase. Your new Craftsman@ product is

designed and manufactured for years of

dependable operation. But like all products,

it may require repair from time to time. That's

when having a Repair Protection Agreement

can save you money and aggravation.

Purchase a Repair Protection Agreement

now and protect yourself from unexpected

hassle and expense.

Here's what's included in the Agreement:

Expert service by our 12,000 professional

repair specialists.

Unlimited service and no charge for parts

and labor on all covered repairs.

Product replacement if your covered

product can't be fixed.

Discount of 25% from regular price of

service and service-related parts not

covered bythe agreement; also, 25% off

regular price of preventive maintenance

check.

Fast help by phone - phone support

from a Sears representative on products

requiring in-home repair, plus convenient

repair scheduling.

Once you purchase the Agreement, asimpte

phone call isall that ittakes for you to sched-

ule service. You can call anytime day or night,

or schedule a service appointment online.

Sears has over 12,000 professional repair

specialists, who have access to over 4.5

million quality parts and accessories. That's

the kind of professionalism you can count on

to help prolong the life of your new purchase

for years to come. Purchase your Repair

Protection Agreement today!

Some limitations and exclusions apply.

For prices and additional information call

1-800=827-6655,

SEARS INSTALLATION SERVICE

For Sears professional installation of home

appliances, garage door openers, water

heaters, and other major home items, in the

U.S.A. call 1-800-4-MY-HOME@.

Keys

_|llb

-Ihll

For Future Use

(2) Keys _ (1) Quick

Connect

Slope Sheet

Your new tractor has been assembled at the factory with the exception of those parts left

unassembted for shipping purposes.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly

easier. Standard wrench sizes are listed.

(1) 1/2" wrench Tire pressure gauge

(2) 7/16" wrenches Utility knife

Pliers

When right or left hand is mentioned in this

manual, itmeans when you areinthe operating

position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM

CARTON

UNPACK CARTON

• Remove all accessible loose parts and

parts cartons from carton.

• Cut along dotted lines on all four panels

of carton. Remove end panels and lay

side panels flat.

• Check for any additional loose parts or

cartons and remove.

BEFORE REMOVING TRACTOR

FROM SKID

ADJUST SEAT

1. Sit in seat.

2. Lift up adjustment lever (A)and slide seat

until a comfortable position is reached

which allows you to press clutch/brake

pedal all the way down.

3. Release lever to lock seat in position.

TO CHECK BATTERY

1. Lift seat to raised position.

NOTE: Ifthis battery is put into service after

month and year indicated on label (label is

located between terminals) charge battery

for minimum of one hour at 6-10 amps. (See

"BATTERY" in Maintenance section of this

manual for charging instructions).

• For batteryand battery cable installation

see "REPLACING BATTERY" in the

"Service and Adjustments" section in

this manual.

NOTE:Youmaynowrollyourtractoroffthe

skid.Continueusingtheinstructionsthat

followtoremovethetractorfromtheskid.

_i, WARNING: Before starting, read, un-

derstand and follow all instructions in the

Operation section of this manual. Be sure

tractor is in a welt-ventilated area. Be sure

the area in front of tractor is clear of other

people and objects.

TO ROLL TRACTOR OFF SKID (See

Operation section for location and

function of controls)

1. Raise attachment lift lever to its highest

position.

2. Release parking brake by depressing

clutch/brake pedal.

3. Place gearshift lever in neutral position.

4. Roll tractor forward off skid.

5. Remove banding holding the deflector

shield up against tractor.

Continue with the instructions that follow.

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at

the factory for shipping purposes. Correct

tire pressure is important for best cutting

performance.

• Reduce tire pressure to PSI shown on

tires.

CHECK DECK LEVELNESS

For best cutting results, mower housing

should be properly leveled. See "TO LEVEL

MOWER" in the Service and Adjustments

section of this manual.

CHECK FOR PROPER POSiTiON

OF ALL BELTS

See the figures that are shown for replac-

ing motion and mower blade drive belts in

the Service and Adjustments section of this

manual. Verify that the belts are routed

correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor,

check to see that the brake is operating

properly. See "TO CHECK BRAKE" in the

Service and Adjustments section of this

manual.

_CHECKLIST

Before you operate your new tractor, we

wish to assure that you receive the best

performance and satisfaction from this

Quality Product.

Please review the following checklist:

_/All assembly instructions have been

completed.

_/No remaining loose parts in carton.

J" Battery isproperly prepared and charged.

_/Seat is adjusted comfortably and tight-

ened securely.

_/All tires are properly inflated. (For ship-

ping purposes, the tires were overinftated

at the factory).

J" Be sure mower deck is properly leveled

side-to-side/front-to-rear for best cutting

results. (Tires must be properly inflated

for leveling).

_/Check mower and drive belts. Be sure

they are routed properly around pulleys

and inside all belt keepers.

_/Checkwiring. Seethatall connectionsare

stillsecureandwires areproperlyctamped.

While learning howto use your tractor, pay ex-

traattention tothe following important items:

_/Engine oil is at proper level.

_/Fuel tank isfilled with fresh, clean, regular

unleaded gasoline.

_/Become familiar with all controls, their

location and function. Operate them

before you start the engine.

_/Be sure brake system isinsafe operating

condition.

_/Be sure Operator Presence System and

Reverse Operation System (ROS) are

working properly (See the Operation and

Maintenance sections in this manual).

These symbols may appear on your tractor or in literature supplied with the product. Learn

and understand their meaning.

R N H L I',,I

REVERSE NEUTRAL HIGH LOW CHOKE FAST SLOW IGNITION

SWITCH

8 6 @

ENGINE ENGINE ENGINE DIFFERENTIAL

OFF START ON LOCK

CLUTCH/ MOWER

BRAKE PEDAL LIFT

PARKING MOWER

BRAKE HEIGHT

REVERSE

OPERATION

SYSTEM(ROS)

REVERSE FORWARD

CRUISE CONTROL LIGHTS ON FUEL BATTERY EAR

PROTECTION

REQUIRED

ATTACHMENT ATTACHMENT DANGER, KEEP

CLUTCH CLUTCH HANDS AND

DISENGAGED ENGAGED FEET AWAY

®@@@@

KEEP AREA CLEAR SLOPE HAZARDS

(SEE SAFETY RULES SECTION)

FREE WHEEL

(Automatic Models only)

Failure to follow instructions

could result in serious injury or

death. The safety alert symbol

is used to identify safety inform-

ation about hazards which can

result in death, serious injury

and/or property damage.

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided,

might result in minor or moderate injury.

CAUTION when used without the alert symbol,

indicates a situation that could result in damage

to the tractor and/or engine.

HOT SURFACES indicates a hazard which,

if not avoided, could result in death, serious

injury and/or property damage.

FIRE indicates a hazard which, if not avoided,

could result in death, serious injury and/or

property damage.

KNOW YOUR TRACTOR

READ THiS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR

Compare the illustrations with your tractor to familiarize yourself with the locations of vari-

ous controls and adjustments. Save this manual for future reference.

.............I

Our tractors conform to the applicable safety standards of the

American National Standards Institute.

(A) ATTACHMENT LIFT LEVER - Used to

raise and lower the mower or other attach-

ments mounted to your tractor.

(B) CLUTCH/BRAKE PEDAL -Used for

declutching and braking the tractor and

starting the engine.

pedal into the brake position.

(D) THROTTLE/CHOKE CONTROL- Used

for starting and controlling engine speed.

(E)ATTACH MENT CLUTCH LEVER - Used

to engage the mower btades, or other attach-

ments mounted to your tractor.

(F) IGNITION SWITCH - Used for starting

and stopping the engine.

(G) REVERSE OPERATION SYSTEM

(ROS) "ON" POSITION - Allows operation

of mower or other powered attachment while

in reverse.

(H) LIGHT SWITCH - Turns the headlights

on and off.

(J) GEARSHIFT LEVER- Selects the speed

and direction of tractor.

The operation of any tractor can result in foreign objects thrown into the eyes, I

which can result in severe eye damage. Always wear safety glasses or eyeI

shields while operating your tractor or performing any adjustments or repairs. I

We recommend standard safety glasses or a wide vision safety mask wornI

over spectacles. J

HOW TO USE YOUR TRACTOR

TO SET PARKING DRAKE

Your tractor is equipped with an operator

presence sensing switch. When engine is

running, any attempt bythe operator to leave

the seat without first setting the parking brake

will shut off the engine.

1. Depress clutch/brake pedal (B) all the

way down and hold.

2. Pull parking brake lever (C) up and hold,

release pressure from brake pedal (B),

then release parking brake lever. Pedal

should remain in brake position. Ensure

parking brake will hold tractor secure.

STOPPING

MOWER BLADES -

To stop mower blades, move attachment

clutch controlto disengaged position (1"_).

(1"_1)Attachment (1_"1)Attachment

Clutch Control Clutch Control

"Engaged .... Disengaged"

GROUND DRIVE -

* Tostop ground drive, depress brake pedal

all the way down.

Move gearshift lever to neutral position.

ENGINE -

* Move throttle control (D) to fast position.

NOTE: Faiture to move throttle controtto fast

position before stopping may cause engine

to "backfire".

Turn ignition key (F) to "STOP" position

and remove key. Always remove key when

leavingtractor toprevent unauthorized use.

Never use choke to stop engine.

IMPORTANT: Leaving the ignition switch in

any position other than "STOP" willcause the

battery to discharge and go dead.

NOTE: Under certain conditions when tractor

is standing idle with the engine running, hot

engine exhaust gases may cause "brown-

ing" of grass. To eliminate this possibility,

always stop engine when stopping tractor

on grass areas.

_k CAUTION: Always stop tractor com-

pletely, as described above, before leaving

the operator's position.

TO USE THROTTLE CONTROL (D)

Always operate engine at full speed (fast).

Operating engine at less than full speed

(fast) reduces engine's operating effi-

ciency.

Full speed (fast) offers the best mower

performance.

TO MOVE FORWARD AND BACKWARD

The direction and speed of movement is

controlled by the gearshift lever (J).

1. Start tractor with clutch/brake pedal

depressed and gearshift lever in neutral

position.

2. Move gearshift lever to desired position.

3. Slowly release clutch/brake pedal to start

movement.

IMPORTANT: Bring tractor to a complete

stop before shifting or changing gears.

Failure to do so will shorten the useful life

of your transaxle.

TO ADJUST MOWER CUTTING HEIGHT

The position of the attachment lift lever (A)

determines the cutting height.

Put attachment lift lever indesired cutting

height slot.

The cutting height range is approximately 1

to 4" (25,4 to 101,6 mm). The heights are

measured from the ground to the blade tip

with the engine not running. These heights

are approximate and may vary depending

upon soil conditions, height of grass and

types of grass being mowed.

The average lawn should be cutto approxi-

mately 2-1/2" (63,5 mm) during the cool

season and to over 3" (76,2 mm) during

hot months. For healthier and better look-

ing lawns, mow often and after moderate

growth.

For best cutting performance, grass over

6" (152,4 mm) in height should be mowed

twice. Make the first cut relatively high; the

second to desired height.

TO ADJUST GAUGE WHEELS

Gauge wheels are properly adjusted when

they are slightly off the ground when mower

is at the desired cutting height in operating

position. Gauge wheels then keep the deck

in proper position to help prevent scalping

in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on

a flat level surface.

1. Adjust mower to desired cutting height

(See "TO ADJUST MOWER CUTTING

HEIGHT" in this section of manual).

2. With mower in desired height of cut posi-

tion, gauge wheels should be assembled

so they are slightly off the ground. Install

gauge wheel inappropriate hole. Tighten

securely.

3. Repeat for all, installing gauge wheel in

same adjustment hole.

TO OPERATE MOWER

Your tractor is equipped with an operator

presence sensing switch. Any attempt

by the operator to leave the seat with the

engine running and the attachment clutch

engaged wilt shut off the engine. You must

remain fully and centrally positioned in the

seat to prevent the engine from hesitating or

cutting off when operating your equipment

on rough, rolling terrain or hills.

1. Select desired height of cut with attach-

ment lift lever.

2. Start mower blades by engaging attach-

ment clutch control.

TO STOP MOWER BLADES

Disengage attachment clutch control.

,_CAUTION: Do not operate the mower

without either the entire grass catcher, on

mowers so equipped, or the deflector shield

in place.

TO OPERATE ON HILLS

_WARNING: Do not drive up or down

hills with slopes greater than 15° and do

not drive across any slope. Use the slope

guide provided at the back of this manual.

• Choose the slowest speed before starting

up or down hills.

• Avoid stopping or changing speed on hills.

• If stopping is absolutely necessary, push

clutch/brake pedal quickly to brake posi-

tion and engage parking brake.

Move gearshift lever to 1st gear. Ensure

you have allowed room for tractor to roll

slightly as you restart movement.

• To restartmovement, slowly release park-

ing brake and clutch/brake pedal.

• Make all turns slowly.

TO TRANSPORT

1. Raise attachment lift lever to its highest.

2. When pushing or towing your tractor, be

sure gearshift lever is in neutral position.

• Do not push or tow tractor at more than

five (5) mph (8 km/h).

NOTE: To protect hood from damage when

transporting your tractor on atruck oratrailer,

be sure hood is closed and secured to tractor.

Use an appropriate means of tying hood to

tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH-

MENTS

Tow only the attachments that are recom-

mended by and comply with specifications

of the manufacturer of your tractor. Use

common sense when towing. Too heavy of

a load, while on a slope, is dangerous. Tires

can lose traction with the ground and cause

you to lose control of your tractor.

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse

Operation System (ROS). Any attempt by

the operator to travel in the reverse direction

with the attachment clutch engaged will shut

off the engine unless ignition key is placed

in the ROS "ON" position.

_WARNING: Backing up with the at-

tachment clutch engaged while mowing is

strongly discouraged. Turning the ROS "ON",

to allow reverse operation with the attach-

ment clutch engaged, should only be done

when the operator decides it is necessary to

reposition the machine with the attachment

engaged. Do not mow in reverse unless

absolutely necessary.

USING THE REVERSE OPERATION

SYSTEM -

Only use if you are certain no children or

other bystanders will enter the mowing area.

1. Depress clutch/brake pedal all the way

down and hold.

2. With engine running, turn ignition key

counterclockwise to ROS "ON" position.

3. Look down and behind before and while

backing.

4. Move gear shift lever to reverse (R)

position and slowly release clutch/brake

pedal to start movement.

5. When use of the ROS is no longer

needed, turn the ignition key clockwise

to engine "ON" position.

ROS "ON" Position

Engine "ON" Position

(Normal Operating)

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped

from the factory already filled with summer

weight oil.

1. Check engine oil with tractor on level

ground.

2. Remove oil fill cap/dipstick and wipe

clean, reinsertthe dipstick and screw cap

tight, wait for a few seconds, remove and

read oil level. If necessary, add oil until

"FULL' mark on dipstick is reached. Do

not overfill.

* For cold weather operation you should

change oil for easier starting (See the oil

viscosity chart inthe Maintenance section

of this manual).

* Tochange engine oil,seethe Maintenance

section in this manual.

ADD GASOLINE

• Fill fuel tank to bottom of filler neck. Do

not overfill. Use fresh, clean, regular

gasoline with a minimum of 87 octane.

Do not mix oil with gasoline. Purchase

fuel in quantities that can be used within

_1_0 days to ensure fuel freshness.

CAUTION" Wipe offany spilled oil orfuel.

Do not store, spill or use gasoline near an

open flame.

IMPORTANT: When operating intempera-

tures below 32°F (0°C), use fresh, clean

winter grade gasoline to help ensure good

cold weather starting.

_CAUTION: Alcohol blended fuels (called

gasohol or using ethanol or methanol) can

attract moisture which leads to separation

and formation ofacids duringstorage. Acidic

gas can damage the fuel system of an engine

while in storage. To avoid engine problems,

the fuel system should be emptied before

storage of 30 days or longer. Drain the gas

tank, start the engine and let it run until the

fuel lines and carburetor are empty. Use

fresh fuel next season. See Storage Instruc-

tions for additional information. Never use

engine or carburetor cleaner products in the

fuel tank or permanent damage may occur.

Fuel stabilizer isan acceptable alternative in

minimizing the formation offuet gum deposits

during storage. Add stabilizer to gasoline in

fuel tank or storage container. Always follow

the mix ratio found on stabilizer container.

Run engine at least 10 minutes after adding

stabilizer to allow the stabilizer to reach the

carburetor. Do not empty the gas tank and

carburetor if using fuel stabilizer.

TO START ENGINE

When starting the engine for the first time or

if the engine has run out of fuel, it will take

extra cranking time to move fuel from the

tank to the engine.

1. Sit on seat in operating position, depress

clutch/brake pedal and set parking brake.

2. Place gear shift lever in neutral position.

3. Move attachment clutch to disengaged

position.

4. Move throttle control to choke position.

NOTE: Before starting, read the warm and

cold starting procedures below.

5. Insert key into ignition and turn key

clockwise to start position and release

key as soon as engine starts. Do not run

starter continuously for more than fifteen

seconds per minute. If the engine does

not start after several attempts, move

throttle control to fast position, wait a

few minutes and try again. If engine still

does not start, move the throttle control

back to the choke position and retry.

WARM WEATHER STARTING

(50°F (10°O) and above)

6. When engine starts, move the throttle

control to the fast position.

• The attachments and ground drive

can now be used. If the engine does

not accept the load, restart the engine

and allow itto warm up for one minute

using the choke as described above.

COLD WEATHER STARTING

(50°F (10°C) and below)

6. When engine starts, leave throttle control

in choke position until engine warms up

and begins to run roughly. Once rough

running begins, immediately move the

throttle control tothe fast position. Engine

warm-up may take from several seconds

to several minutes (the colder the tem-

perature, the longer the warm-up).

The attachments can also be used

during the engine warm-up period.

MOWING TIPS

• DO NOT use tire chains when the mower

housing is attached to tractor.

• Mower should be properly leveled for best

mowing performance. See "TO LEVEL

MOWER HOUSING" in the Service and

Adjustments section of this manual.

The left hand side of mower should be

used for trimming.

• Drive so that clippings are discharged onto

the area that has already been cut. Have

the cut area to the right of the tractor. This

will result in a more even distribution of

clippings and more uniform cutting.

• When mowing large areas, start by turning

to the right so that clippings will discharge

away from shrubs, fences, driveways,

etc. After one or two rounds, mow inthe

opposite direction making left hand turns

until finished.

l[ J

If grass is extremely tall, it should be

mowed twice to reduce load and possible

fire hazard from dried clippings. Make

first cut relatively high; the second to the

desired height.

Do not mow grass when it is wet. Wet

grass will plug mower and leave undesir-

able clumps. Allow grass to dry before

mowing.

• Always operate engine at full throttle

when mowing to assure better mow-

ing performance and proper discharge

of material. Regulate ground speed by

selecting a low enough gear to give the

mower cutting performance as well as the

quality of cut desired.

• When operating attachments, select a

ground speed that will suit the terrain and

give best performance of the attachment

being used.

MAINTENANCE BEFORE EVERY

EACH 8

SCHEDULE USE HOURS

Check Brake Operation if

Check Tire Pressure

T Check Operator Presence & ROS Systems

A Check for Loose Fasteners

C Check/Replace Mower Blades

1 Lubrication Chart

0 Check Battery Level

R Clean Battery and Terminals

Clean Debris Off Steering Plate

Check Transaxle Cooling

Check Mower Levelness

Check V-Belts

Check Enqine Oil Level _#_ if

Chanqe Enqine Oil Cmodels with oil filter)

Change Engine Oil (models without oil filter)

NE Clean Air Filter

G Clean Air Screen

J Inspect Muffler/Spark Arrester

N Replace Oil Filter !If equipped)

E Clean Engine Cooling Fins

Replace Spark Plug

Replace Air Filter Paper Cartridge

EVERY EVERY EVERY EVERY BEFORE

25 50 r00 SEASON STORAGE

HOURS HOURS HOURS

l/ v'

v',,2

_/ v"

-- Re lace Fuel Filter ..... ___

Changemo[eofter_whenoper_tEngu_def_heawlc_do[il_hJgh_tmbJenttempe_atures 3 Repl_oebJadesmo[eofter_whe_m_vil_gil_gandysoil 5 SeeCleaninginMaintenanceSectior_

2 Se_vic_moreofter_whenoper_tingindi_tyordustyoor_ditior_s 4 Not_equi_edifequippedwithm_tinten_ncefreebatte_¥

GENERAL RECOMMENDATIONS

The warranty on this tractor does not cover

items that have been subjected to operator

abuse or negligence. To receive full value

from the warranty, operator must maintain

tractor as instructed in this manual.

Some adjustments will need to be made

periodically to properly maintain your tractor.

At least once a season, check to see if

you should make any of the adjustments

described in the Service and Adjustments

section of this manual.

* At least once a year you should replace

the spark plug, clean or replace air filter,

and check blades and belts for wear. A

new spark plug and clean air filter assure

proper air-fuel mixture and help your en-

gine run better and last longer.

BEFORE EACH USE

1. Check engine oil level.

2. Check brake operation.

3. Check tire pressure.

4. Check operator presence and

ROS systems for proper operation.

5. Check for loose fasteners.

LUBRICATION CHART

(_Steering Pivot Bolts

(_ S Spindle

Zerk Zerk

Front

Wheel Wheel

Bearing Bearing

Zerk _Zerk

'x_ Engine

Steerinc

Sector Gear

Teeth

(_General Purpose Grease

@Refer to Maintenance "ENGINE" Section.

_MPORTANT: Do not oil or grease the pivot

points which have special nylon bearings.

Viscous lubricants will attract dust and dirt

that will shorten the life of the self-lubricating

bearings. Ifyou feet they must be lubricated,

use only a dry, powdered graphite type

lubricant sparingly.

TRACTOR

Alwaysobservesafetyruleswhenperform-

inganymaintenance.

BRAKEOPERATION

if tractor requires more than 5 feet (1,5 m)

to stop at highest speed in highest gear on

a level, dry concrete or paved surface, then

brake must be serviced. (See "TO CHECK

BRAKE" in the Service and Adjustments

section of this manual).

TIRES

• Maintain proper air pressure in all tires

(See the side of tires for proper PSI.)

• Keep tires free of gasoline, oil, or insect

control chemicals which can harm rubber.

• Avoid stumps, stones, deep ruts, sharp

objects and other hazards that may cause

tire damage.

NOTE: To seal tire punctures and prevent

flat tires due to slow leaks, tire sealant may

be purchased from your local parts dealer.

Tire sealant also prevents tire dry rot and

corrosion.

OPERATOR PRESENCE SYSTEM AND

REVERSE OPERATION SYSTEM (ROS)

Be sure operator presence and reverse

operation systems are working properly. If

your tractor does not function as described,

repair the problem immediately.

• The engine should not start unless the

brake pedal is fully depressed, and the

attachment clutch control is in the disen-

gaged position.

CHECK OPERATOR PRESENCE SYSTEM

• When the engine is running, any attempt

by the operator to leave the seat without

first setting the parking brake should shut

off the engine.

• When the engine is running and the at-

tachment clutch is engaged, any attempt

by the operator to leave the seat should

shut off the engine.

• The attachmentctutch should never oper-

ate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS)

SYSTEM

• When the engine isrunning with the ignition

switch inthe engine "ON" position and the

attachment clutch engaged, any attempt

by the operator to drive in reverse should

shut off the engine.

• When the engine isrunning with the ignition

switch in the ROS "ON" position and the

attachment clutch engaged, any attempt

by the operator to drive in reverse should

NOT shut off the engine.

Ros "On" Engine "On" Position

Position (Normal Operating)

BLADE CARE

For best results mower blades must be sharp.

Replace worn, bent or damaged blades.

_L, CAUTION: Use onlya replacement blade

approved bythe manufacturer of your tractor.

Using a blade not approved by the manu-

facturer of your tractor is hazardous, could

damage your tractor and void your warranty.

BLADE REMOVAL

1. Raise mower to highest position to allow

access to blades.

NOTE: Protect your hands with gloves and/

or wrap blade with heavy cloth.

2. Remove blade bolt by turning counter-

clockwise.

3. install new blade with stamped "GRASS

SIDE" facing the ground.

IMPORTANT: To ensure proper assembly,

center hole in blade must align with star on

mandrel assembly.

4. install and tighten blade bolt securely

(45-55 Ft. Lbs./62-75 Nm).

IMPORTANT: Special blade bolt is heat

treated.

Star

Center Hole \

Blade Bolt "_ Mandrel

(Special) -...._ _ Assembly

Blade

BATTERY

Your tractor has a battery charging system

which is sufficient for normal use. However,

periodic charging of the battery with an au-

tomotive charger will extend its life.

• Keep battery and terminals clean.

• Keep battery bolts tight.

• Keep small vent holes open.

• Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on

your tractor is maintenance free. Do not

attempt to open or remove caps or covers.

Adding or checking level of electrolyte is

not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirton the battery and terminals

can cause the battery to "leak" power.

1. Remove terminal guard.

2. Disconnect BLACK battery cable first

then RED battery cable and remove

battery from tractor.

3. Rinse the battery with plain water and

dry.

4. Clean terminals and battery cable ends

with wire brush until bright.

5. Coatterminals with grease or petroleum

jelly.

6. Reinstall battery (See "REPLACING

BATTERY" in the Service and Adjust-

ments section of this manual).

TRANSAXLE MAINTENANCE

Keep transaxle free from build-up of dirt and

chaff which can restrict cooling.

Do not attempt to clean transaxte while

engine is running or while the transaxle is

hot. To prevent possible damage to seals,

do not use high pressure water or steam to

clean transaxte.

V=BELTS

CheckV-betts for deterioration and wear after

100 hours of operation and replace if neces-

sary. The belts are not adjustable. Replace

belts if they begin to slip from wear.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with

API service classification SG-SL. Selectthe oil's

SAE viscosity grade according to your expected

operating temperature.

TO CHANGE ENGINE OiL

Determine temperature range expected

before oil change. All oil must meet API

service classification SG-SL

Ensure tractor is on level surface.

Oil will drain more freely when warm.

Catch oil in a suitable container.

LOWER DASH COVER REMOVAL

1. Raise hood.

2. Remove fastener from lower dash cover.

CAUTION: Remove lower dash cover care-

fully to ensure cover tabs are not broken.

3. Slide lower dash cover up to release

cover tabs from tapered slots in lower

dash and remove.

Lower Dash

4. Remove oil fill cap/dipstick. Be careful

not to allow dirt to enter the engine when

changing oil.

5. Remove yellow cap from end of drain

valve and install the drain tube onto the

fitting.

6. Unlock drain valve by pushing inward

and turning counterclockwise.

7. To open, putt out on the drain valve.

Oil DrainValve

SAE VISCOSITY GRADES

m., 324_ Closed __ _I_

c-3o -e'o -_ _ 1'o _o ,_0 40 Locked _--_'__A Drain

xzo osi,ion . e

NOTE: Although multi-viscosity oils (5W30,

10W30 etc.) improve starting in cold weather,

they will resultin increasedoil consumptionwhen Yellow Cap_

usedabove32°F/0°C. Checkyourengineoillevel

more frequently to avoid possible engine damage

from running low on oil.

Change the oil after every 50 hours of operation

or at least once a year if the tractor is not used

for 50 hours in one year.

Check the crankcase oil level before starting the

engine and after each eight (8) hours of operation.

Tighten oil fill cap/dipstick securely each time you

check the oil level.

8. After oil has drained completely, close and

lock the drain valve by pushing inward

and turning clockwise until the pin is in

the locked position as shown.

9. Removethe drain tube and reptacethe cap

onto tothe bottom fitting of the drain valve.

10. Refill engine with oil through oil fill dipstick

tube. Pour slowly. Do not overfill. For

approximate capacity see "PRODUCT

SPECIFICATIONS"section ofthis manual.

11.Usegaugeonoilfill cap/dipstickfor

checkinglevel.Ensuredipstickcapis

tightenedsecurelyforaccuratereading.

Keepoilat"FULL'lineondipstick.Tighten

capontothetubesecurelywhenfinished.

ENGINE OiL FILTER

Replace the engine oil filter every season or

every other oil change if the tractor is used

more than 100 hours in one year.

NOTE: Ifneeded, remove lower dash covers

using steps from "Lower dash cover removal"

section of this manual.

AiR FILTER

Your engine will not run properly using a

dirty air filter. Service air cleaner more often

under dusty conditions.

CLEAN AiR SCREEN

The air screen is over the air intake blower

located on top of engine. The air screen

must be kept free of dirt and chaff to prevent

engine damagefrom overheating. Cteanwith

a wire brush or compressed air to remove

dirt and stubborn dried gum fibers.

ENGINE COOLING SYSTEM

Debris may clog the engine's air cooling

system. Remove blower housing and clean

the area shown to prevent overheating and

engine damage.

Air--Clean

Screen _ _._ Out

__ __ Chaff

[-- _//J_'_ [_d_L_ And

L __ Debris

MUFFLER

inspect and replace corroded muffler and

spark arrester (ifequipped) as it could create

a fire hazard and/or damage.

SPARK PLUG(S)

Replace spark plug(s)atthe beginningof

each mowing season or afterevery I00

hours ofoperation,whicheveroccursfirst.

Spark plugtypeand gap settingareshown

in"PRODUCT SPECIFICATIONS" section

of this manual.

IN=LINE FUEL FILTER

The fuel filter should be replaced once each

season. If fuel filter becomes clogged, ob-

structing fuel flow to carburetor, replacement

is required.

1. With engine cool, remove filter and plug

fuel line sections.

2. Place new fuel filter in position infuel line

with arrow pointing towards carburetor.

3. Ensure there are no fuel line leaks and

clamps are properly positioned.

4. Immediatetywipe upanyspilled gasoline.

CLEANING

• Clean engine, battery, seat, finish, etc.

of all foreign matter.

• Clean debris from steering plate. Debris

can restrict clutch/brake pedal shaft move-

ment, causing belt slip and loss of drive.

A CAUTION: Avoid all pinch points and

movable parts

Steering System, Dash, Fender

and Mower Not Shown

• Keep finished surfaces and wheels free

of all gasoline, oil, etc.

• Protect painted surfaces with automotive

type wax.

Except for the washout port (if equipped),

we do not recommend using a garden hose

or pressure washer to clean the outside of

your tractor unless the engine and transmis-

sion are covered to keep water out. Water

in engine or transmission will shorten the

useful life of your tractor. Use compressed

air or a leaf blower to remove grass, leaves

and trash from outside tractor and mower.

DECK WASHOUT PORT

Your tractor's deck is equipped with a washout

port as part of its deck wash system, tt should

be utilized after each use,

1, Drive the tractor to a level, clear spot on

your lawn, near enough to a water spigot

for your garden hose to reach,

IMPORTANT: Make certain the tractor's

discharge chute is directed AWAY from your

house, garage, parked cars, etc. Remove bag-

ger chute or mulch cover if attached.

2. Make sure the attachment clutch control

is in the "DISENGAGED" position, set

the parking brake, and stop the engine.

3. Thread the nozzle adapter (packaged with

your tractor's Operator's Manual) ontothe

end of your garden hose.

4. Pull back the lock collar of the nozzle

adapter and push the adapter onto the

deck washout port at the left end of the

mower deck. Release the lock collar to

lock the adapter on the nozzle.

Washout Port

7, Move the tractor's attachment clutch con-

trol to the "ENGAGED" position, Remain

in the operator's position with the cutting

deck engaged until the deck is cleaned.

8. Move the tractor's attachment clutch con-

trol to the "DISENGAGED" position. Turn

the ignition keyto the STOP position to turn

the tractor's engine off. Turn the water off.

9. Pull back the lock collar of the nozzle

adapter to disconnect the adapter from

the nozzle washout port.

10. Move the tractor to a dry area, preferably

a concrete or paved area. Place the at-

tachment clutch control in the"ENGAG ED"

position to remove excess water and to

help dry before putting the tractor away.

_,WARNING: A broken or missing washout

fitting could expose you or others to thrown

objects from contact with the blade.

Replace broken or missing washout fitting

immediately, prior to using mower again.

Plug any holes in mower with bolts and

Iocknuts.

IMPORTANT: Tug hose ensuring connection

is secure.

5. Turn the water on.

6. While sitting in the operator's position on

the tractor, re-start the engine and place

the throttle lever in the Fast ",_" position.

IMPORTANT: Recheck the area to ensure the

area is clear. Ensure no children are in the

area while cleaning the deck.

WARNING: TO AVOID SERIOUS iNJURY, BEFORE PERFORMING ANY

SERVICE OR ADJUSTMENTS:

1. Depress clutch/brake pedal fully and set parking brake.

2. Place gearshift lever in neutral position.

3. Place attachment clutch in "DISENGAGED" position.

4. Turn ignition key to "STOP" and remove key.

5. Ensure the blades and all moving parts have completely stopped.

6. Disconnect spark plug wire from spark plug and place wire where it cannot

come in contact with plug.

TO REMOVE MOWER

1. Place attachment clutch in "DISEN-

GAGED" position.

2. Lower attachment lift lever to its lowest

position.

3. Roll belt off engine pulley (M) and belt

keepers (G).

4. Remove retainer spring (K), slide collar

(L) off and push housing guide (P) out

of bracket.

5. Remove clutch cable spring (Q) from

idler arm (R).

6. Disconnect front link (E) from mower -

remove retainer spring and washer.

7. Go to either side of mower and discon-

nect mower suspension arm (A) from

chassis pin (B) and rear lift link (C) from

rear mower bracket (D) -remove retainer

springs and washers.

CAUTION: After rear lift links are discon-

nected, the attachment lift lever will be spring

loaded. Have a tight grip on lift lever when

changing position of the lever.

8. Slide mower out from under right side of

tractor.

IMPORTANT: If an attachment other than

the mower is to be mounted on the tractor,

remove the front link (E) and rear lift links

(Q) into the cable guide on front edge of

lower dash.

TO iNSTALL MOWER

Ensure tractor ison level surface and engage

parking brake.

1. Lower attachment lift lever to its lowest

position.

CAUTION: Lift lever is spring loaded.

Have a tight grip on lift lever, lower it slowly

and engage in lowest position.

NOTE: Ensure mower side suspension arms

(A)are pointing forward before sliding mower

under tractor.

2. Slide mower under tractor until it is cen-

tered under tractor.

03042tex

Page is loading ...

Craftsman 917.20380 User manual

Brand: Craftsman

Model: 917.20380

Category: Lawnmowers

Type: User manual

Download PDF

report

in other languages

español: Craftsman 917.20380 Manual de usuario

Craftsman 917.20380 User manual

Craftsman 917.20380 User manual

in other languages

Related papers

Other documents