Skil 0780 AA Owner's manual

CHAIN SAW

0780 (F0150780 . . )

SKIL Europe BV - Konijnenberg 60 04/11 2610Z01557

4825 BD Breda - The Netherlands

www.skileurope.com



ORIGINAL INSTRUCTIONS

9



NOTICE ORIGINALE

14



ORIGINALBETRIEBSANLEITUNG

21



ORIGINELE GEBRUIKSAANWIJZING

28



BRUKSANVISNING I ORIGINAL

35



ORIGINAL BRUGSANVISNING

40



ORIGINAL BRUKSANVISNING

46



ALKUPERÄISET OHJEET

52



MANUAL ORIGINAL

58



MANUAL ORIGINAL

65



ISTRUZIONI ORIGINALI

72



EREDETI HASZNÁLATI UTASÍTÁS

79



PŮVODNÍM NÁVODEM K POUŽÍVÁNÍ

86



ORİJİNAL İŞLETME TALİMATI

92



INSTRUKCJA ORYGINALNA

98



ПОДЛИННИК РУКОВОДСТВА

ПО ЭКСПЛУАТАЦИИ

105



ОРИГІНАЛЬНА ІНСТРУКЦІЯ

З ЕКСПЛУАТАЦІЇ

113



ΠΡΩΤΟΤΥΠΟ Ο∆ΗΓΙΩΝ ΧΡΗΣΗΣ

120



INSTRUCŢIUNI DE FOLOSIRE

ORIGINALE

128



ОРИГИНАЛНО РЪКОВОДСТВО

ЗА ЕКСПЛОАТАЦИЯ

134



PÔVODNÝ NÁVOD NA POUŽITIE

142



ORIGINALNE UPUTE ZA RAD

148



ORIGINALNO UPUTSTVO ZA RAD

154



IZVIRNA NAVODILA

160



ALGUPÄRANE KASUTUSJUHEND

166



ORIĢINĀLĀ LIETOŠANAS PAMĀCĪBA

172



ORIGINALI INSTRUKCIJA

179



196



192

Page is loading ...

9



Chain saw 0780

INTRODUCTION

• The power tool is intended for sawing wood such as

wooden beams, planks, branches, tree trunks, etc.,

and for sawing of trees; cuts can be sawed with or

across the grain

• This tool is not intended for professional use

• Check whether the packaging contains all parts as

illustrated in drawing 2

• When parts are missing or damaged, please contact

your dealer

• Read this instruction manual carefully before use

and save it for future reference 3

• Pay special attention to the safety instructions and

warnings; failure to follow these may result in

serious injury

TECHNICAL SPECIFICATIONS 1

TOOL ELEMENTS 2

A Cover plate

B Locking knob

C Chain

D Chain bar

E Symbol for rotation and cutting direction

F Drive sprocket

G Fastening bolt

H Guide ns for chain bar

J Chain tensioning peg

K Chain tensioning knob

L Oil outlet

M Oil reservoir cap

N Minimum mark

P Cord restraint

Q Safety switch

R Trigger switch

S Activation lever for kickback brake (hand guard)

T Front handle

U Rear handle

V Metal gripping teeth

W Ventilation slots

X Chain guard

Y Storage rail (screws not supplied)

Z Storage hook

SAFETY

GENERAL SAFETY INSTRUCTIONS

WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and instructions

may result in electric shoc k, fire and/or serious injury.

Save all warnings and instructions for future

reference. The term “power tool” in the warnings refers

to your mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodied plugs and matching outlets will reduce risk of

electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is

unavoidable, use an earth leakage circuit breaker.

Use of an earth leakage circuit breaker reduces the risk

of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personal injury.

b) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your nger on the

switch or energising power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpected situations.

10

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

CHAIN SAW SAFETY WARNINGS

• Children and juveniles, with the exception of

apprentices older than 16 years and under

supervision, may not operate the chain saw. The

same applies for persons who do not or do not

sufficiently know how to handle the chain saw. The

operating instructions should always be ready to hand.

Persons unt or tired must not operate the chain saw.

• Keep all parts of the body away from the saw chain

when the motor is operating. Before you start the

saw, make sure the saw chain is not contacting

anything. A moment of inattention while operating chain

saws may cause entanglement of your clothing or body

with the saw chain.

• Always hold the chain saw with your right hand on

the rear handle and your left hand on the front

handle. Holding the chain saw with a reversed hand

conguration increases the risk of personal injury and

should never be done.

• Hold the power tool by insulated gripping surfaces

only, because the saw chain may contact hidden

wiring or its own cord. Saw chains contacting a “live”

wire may make exposed metal parts of the power tool

“live” and could give the operator an electric shock.

• Wear safety glasses and hearing protection. Further

protective equipment for head, hand, legs and feet

is recommended. Adequate protective clothing will

reduce personal injury by ying debris or accidental

contact with saw chain.

• Do not operate a chain saw in a tree. Operation of a

chain saw in a tree, may result in personal injury.

• Always keep proper footing and operate the chain

saw only when standing on fixed, secure and level

surface. Slippery or unstable surfaces such as ladders

may cause a loss of balance or control of the chain saw.

• When cutting a limb that is under tension be alert

for spring back. When the tension in the wood bres is

released the spring loaded limb may strike the operator

and/or throw the chain saw out of control.

• Use extreme caution when cutting brush and

saplings. The slender material may catch the saw chain

and be whipped toward you or pull you o balance.

• Carry the chain saw by the front handle with the

chain saw switched off and away from your body.

When transporting or storing the chain saw, always

fit the guide bar cover. Proper handling of the chain

saw will reduce the likelihood of accidental contact with

the moving saw chain.

• Follow instructions for lubricating, chain tensioning and

changing accessories. Improperly tensioned or lubricated

chain may either break or increase the chance for kickback.

• Keep handles dry, clean, and free from oil and grease.

Greasy, oily handles are slippery causing loss of control.

• Cut wood only. Don’t use chain saw for purposes

not intended (e.g. do not use chain saw for cutting

plastic, masonry or non-wood building materials).

Use of the chain saw for operations dierent than

intended could result in a hazardous situation.

CAUSES AND OPERATOR PREVENTION OF KICKBACK

• Kickback may occur when the nose or tip of the guide bar

touches an object, or when the wood closes in and

pinches the saw chain in the cut

• Tip contact in some cases may cause a sudden reverse

reaction, kicking the guide bar up and back towards

the operator

• Pinching the saw chain along the top of the guide bar

may push the guide bar rapidly back towards the operator

• Either of these reactions may cause you to lose control of

the saw which could result in serious personal injury (do

not rely exclusively upon the safety devices built into your

saw; as a chain saw user, you should take several steps

to keep your cutting jobs free from accident or injury)

• Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be avoided

by taking proper precautions as given below:

- maintain a firm grip, with thumbs and fingers

encircling the chain saw handles, with both hands

on the saw and position your body and arm to

allow you to resist kickback forces (kickback forces

can be controlled by the operator, if proper precautions

are taken; do not let go of the chain saw)

11

- do not over reach and do not cut above shoulder

height (this helps prevent unintended tip contact

and enables better control of the chain saw in

unexpected situations)

- only use replacement bars and chains specified

by the manufacturer (incorrect replacement bars

and chains may cause chain breakage and/

or kickback)

- follow the manufacturer’s sharpening and

maintenance instructions for the saw chain

(decreasing the depth gauge height can lead to

increased kickback)

PERSONAL SAFETY

• It is recommended that the rst time user should have

practical instruction in the use of the chainsaw and the

protective equipment from an experienced operator and

that the initial practice should be cutting logs on a saw

horse or cradle

• Do not touch rotating chain

• Do not operate chain saw near other people,

children or animals

• Do not operate chain saw after drinking alcohol

or under the influence of intoxicating drugs

or medication

• This tool is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the tool by a person responsible

for their safety

• Ensure that children do not play with the tool

ELECTRICAL SAFETY

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

• Connect the tool via a fault current (FI) circuit breaker

with a triggering current of 30 mA maximum

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• Only use an extension cord which is intended for

outdoor use and equipped with a watertight plug

and coupling-socket

• Only use extension cords with a maximum length of

20 metres (1,5 mm²) or 50 metres (2,5 mm²)

• Always switch o tool and disconnect plug from power

source if the power supply cord or the extension cord is

cut, damaged or entangled (do not touch the cord

before disconnecting the plug)

• Protect the (extension) cord from heat, oil and

sharp edges

• Never use the cord for carrying, pulling or unplugging

the tool

• Inspect the cord periodically and have it replaced by

a qualied person, if damaged

• Inspect the extension cord periodically and replace it,

if damaged (inadequate extension cords can

be dangerous)

• Do not use the tool if the switch does not turn it on and

o; always have a damaged switch repaired by a

qualied person

EXPLANATION OF SYMBOLS ON TOOL

3 Read the instruction manual before use

4 Always switch off tool and disconnect plug from power

source if the power supply cord or the extension cord is

cut, damaged or entangled (do not touch the cord before

disconnecting the plug)

5 Do not expose tool to rain

6 Wear protective glasses and hearing protection

7 Double insulation (no earth wire required)

8 Do not dispose of the tool together with household

waste material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Assembly 9

! do not connect the chain saw to mains before

it is completely assembled

! always use gloves when handling the chain

- place the chain saw on any suitable at surface

- remove cover plate A by turning locking knob

B counter-clockwise

- slide chain C in the slot around chain bar D

! ensure chain is in correct running direction by

comparing with chain symbol E

- t the chain onto drive sprocket F and guide chain

bar D, so that fastening bolt G and the two guide

ns H t into the keyway of chain bar D, and that

chain tensioning peg J ts into the respective hole

of chain bar D

- if necessary, turn tensioning knob K to bring tensioning

peg J in alignment with the hole in chain bar D

- check if all parts are seated properly and hold chain

and chain bar in a level position

- turn tensioning knob K until all the slack is taken up in

the chain

- mount cover plate A as illustrated

- tighten locking knob B on fastening bolt G by turning

it clockwise

• Tensioning chain 0

- place the chain saw on any suitable at surface

- check if the chain links are correctly located in the slot

around chain bar D

1) loosen locking knob B until it is just holding chain bar

in position (do not remove)

2) lift the chain bar somewhat and hold it in that position

3) turn chain tensioning knob K upwards until the lowest

chain links come up and JUST touch the bottom of

chain bar D

4) tighten locking knob B by turning it clockwise

5) release chain bar

6) the correct chain tension is reached when the chain can

be raised approx. 4 mm from the chain bar in the centre

! always check the chain tension before use, after

the first cuts and regularly during use (approx.

every 10 minutes)

- upon initial operation, new chains can

lengthen considerably

12

- the chain life of the saw chain mainly depends upon

sucient lubrication and correct tensioning

- avoid tensioning the chain if it is hot, as this will cause

the chain to become overtensioned when it cools down

• Lubrication !

Chain life and cutting capacity depend on optimum

lubrication; therefore the chain is automatically oiled

during operation via oil outlet L 2

! the chain saw is not supplied filled with oil; it is

essential to fill with oil before use

! never operate the chain saw without chain oil or

at an empty oil reservoir level, as this will result

in extensive damage to the product

- set chain saw on any suitable surface with oil reservoir

cap M facing upward

- unscrew cap and add chain saw oil (not included)

until reservoir is full

- avoid dirt or debris entering oil reservoir

- mount oil reservoir cap and tighten

! check oil level prior to starting and regularly

during operation; refill oil when oil level is below

indicator N

- the oil reservoir lling will last approx. 15 minutes,

depending on sawing intensity and stops

- never use recycled/old oil

• Cord restraint @

- hook the loop in the extension cord over restraint P

as illustrated

- pull tight to secure the extension cord

• On/o #

- switch on tool by rst pressing safety switch Q and

then pulling trigger switch R

- switch o the tool by releasing trigger R

! do not stop chain saw after sawing by activating

front hand guard S 2 (= kickback brake)

• Kickback brake $

The kickback brake is a safety mechanism activated

through front hand guard S, when kickback occurs ->

chain stops immediately

The following function check should be carried out at

regular intervals:

- push front hand guard S forward and start the

chain saw -> the chain must not start

- to deactivate the kickback brake, release trigger

switch R and pull hand guard S backwards

• Operating the tool %

- always hold the chain saw rmly with both hands

(front handle T with the left hand and rear handle U

with the right hand); never operate chain saw using

only one hand %a

- ensure power cord is located to the rear, away from

the chain and wood and so postioned that it will not

be caught on branches or the like during cutting

! the chain must be running at full speed before

it makes contact with the wood

- use metal gripping teeth V to secure the saw onto

the wood before starting to cut %a

- use the gripping teeth as a leverage point “✱” while

cutting %a

- reset the gripping teeth at a lower point when sawing

thicker logs by pulling the chain saw slightly

backwards until the gripping teeth release, and

reposition at a lower level to continue sawing; do not

remove the saw completely from the wood

- do not force the chain while cutting; let the chain do

the work, using gripping teeth V to apply minimum

leverage pressure

- use the chain saw only with secure footing

- hold the chain saw at the right-hand side of your body %b

- do not operate the chain saw with arms fully extended

or attempt to saw areas which are dicult to reach, or

on a ladder %c

- never use the chain saw above shoulder height %d

- sawing is optimized when the chain speed remains

steady during cutting

! beware when reaching the end of the cut; the

weight of the saw may change unexpectedly as it

cuts free from the wood (accidents may occur to

legs and feet)

! always remove the saw from a wood cut while the

saw is running

• Cutting logs

- support logs so that the face sides at the cut do not

close in against each other, which would result in the

chain being jammed or pinched

- position and set short logs safely prior to sawing

- when sawing, always take care to avoid hitting stones,

nails, etc., as these could be thrown up or cause damage

to the chain or serious injury to the operator or bystanders

! keep a running chain clear of wire fencing or

the ground

- length cuts must be carried out with care, as leverage

with gripping teeth V 2 is not possible; saw at a at

angle to avoid kickback

- there is a high risk of accidents when sawing wood,

branch or trees under tension; be extremely careful

(leave saw jobs like these to professionalsl)

• Bucking a log (cutting a log into lengths)

- when possible, the log should be raised and supported

by the use of limbs, logs or chocks

- it is important to make sure your footing is rm and

your weight is evenly distributed on both feet

- when the log is supported along its entire length as

illustrated, it is cut from the top (overbuck) ^a

- when the log is supported on one end as illustrated,

cut 1/3 the diameter from the underside (underbuck);

then make the nished cut by overbucking to meet the

rst cut ^b

- when the log is supported on both ends as illustrated,

cut 1/3 the diameter from the top (overbuck); then

make the nished cut by underbucking the lower 2/3 to

meet the rst cut ^c

- when bucking on a slope always stand on the uphill

side of the log

- when “cutting through”, to maintain complete control

release the cutting pressure near the end of the cut

without relaxing your grip on the chain saw handles.

! do not let the chain contact the ground

- after completing the cut, wait for the saw chain to stop

before you move the chain saw

- always stop the motor before moving from tree to tree

13

• Felling trees &

! the chain saw can only be used to fell trees smaller

in diameter than the length of the chain bar

! secure work area; ensure no persons or animals

are in the vicinity of the falling tree

! never attempt to free a jammed saw with the

motor running; use wooden wedges to free chain

and chain bar

! always wear hard hat to protect head against

falling branches

BEFORE FELLING:

- when cutting and felling operations are being

performed by two or more persons at the same time,

the felling operations should be separated from the

cutting operation by a distance of at least twice the

height of the tree being felled

- trees should not be felled in a manner that would

endanger any person, strike any utility line or cause any

property damage (if the tree does make contact with any

utility line, the company should be notied immediately)

- the chain saw operator should keep on the uphill side

of the terrain as the tree is likely to roll or slide downhill

after it is felled

- an escape path should be planned and cleared as

necessary before cuts are started (the escape path

should extend back and diagonally to the rear of the

expected line of fall) &a

- before felling is started, consider the natural lean of

the tree, the location of larger branches and the wind

direction to judge which way the tree will fall

- remove dirt, stones, loose bark, nails, staples and wire

from the tree

FELLING PROCEDURE:

- make the notch (1 – 2) 1/3 the diameter of the tree,

perpendicular to the direction of falls as illustrated &b

- make the lower horizontal notching cut rst (this will

help to avoid pinching either the saw chain or the

guide bar when the second notch is being made)

- make the felling back cut (3) at least 50 mm higher

than the horizontal notching cut (keep the felling back

cut parallel to the horizontal notching cut) &b

- make the felling back cut so enough wood is left to act as

a hinge (the hinge wood keeps the tree from twisting and

falling in the wrong direction; do not cut through the hinge)

- as the felling gets close to the hinge the tree should

begin to fall

- if there is any chance that the tree may not fall in desired

direction or it may rock back and bind the saw chain,

stop cutting before the felling back cut is complete and

use wedges of wood, plastic or aluminium to open the

cut and drop the tree along the desired line of fall &c

- when the tree begins to fall remove the chain saw from

the cut, stop the motor, put the chain saw down, then

use the retreat path planned (be alert for overhead

limbs falling and watch your footing)

• Limbing a tree *

Limbing is removing the branches from a fallen tree

- when limbing leave larger lower limbs to support the

log o the ground

- remove the small limbs in one cut as illustrated

- branches under tension should be cut from the bottom

up to avoid binding the chain saw

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always disconnect plug from power source before

cleaning and/or maintenance

• Always keep tool and cord clean (especially ventilation

slots W 2)

- clean the moulded plastic housing of the chain saw

using a soft brush and clean cloth (do not use water,

solvents or polishes)

- remove and brush clean the cover plate, chain and

chain bar after 1 to 3 hours of use

- clean the area under cover plate, drive sprocket and

chain bar assembly using a soft brush and clean cloth

- clean oil outlet with a clean cloth

• Regularly check for obvious defects such as loose,

dislodged or damaged chain and chain bar, loose xings,

and worn or damaged components

• Carry out necessary maintenance and repairs before

using the chain saw

• Proper functioning of the automatic oiler can be checked

by running the chain saw and pointing the tip of the chain

bar towards a piece of cardboard or paper on the ground

! do not touch the ground with the chain (ensure

safety clearance of 20 cm)

- if an increasing oil pattern developes, the automatic

oiler is operating ne

- if there is no oil pattern, despite a full oil reservoir, see

“TROUBLESHOOTING” or contact your dealer

• If the tool should fail despite the care taken in manufacturing

and testing procedures, repair should be carried out by an

after-sales service centre for SKIL power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skileurope.com)

! before returning, the oil reservoir must be

completely emptied

• Storage (

- if the chain saw is to be stored for a longer period of

time, clean chain and chain bar

- when storing tool, the oil reservoir must be

completely emptied

- use chain guard X when storing the tool

- securely mount storage rail Y on the wall with 4 screws

(not supplied) and horizontally leveled

- use storage rail Y and storage hook Z as illustrated

- be aware of oil leakage when using storage hook Z

- store the tool indoors in a dry and locked-up place,

out of reach of children

TROUBLESHOOTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify and

correct the problem, contact your dealer or service station)

! switch off the tool and disconnect the plug before

investigating the problem

★ Tool does not operate

- kickback brake is activated -> pull hand guard S 2

back in position $a

- no power supply -> check power supply

(power cable, circuit breakers, fuses)

- plug not connected -> connect plug

- extension cord damaged -> replace extension cord

14

★ Tool operates intermittently

- on/o switch defective -> contact dealer/service station

- internal wiring defective -> contact dealer/service station

- extension cord damaged -> replace extension cord

★ Dry chain

- no oil in reservoir -> rell oil

- vent in oil reservoir cap clogged -> clean cap

- oil passage clogged -> clean oil passage outlet

★ Brake does not stop chain

- kickback brake/run-down brake defective ->

contact dealer/service station

★ Chain/chain bar overheats

- no oil in reservoir -> rell oil

- vent in oil reservoir cap clogged -> clean cap

- oil passage clogged -> clean oil passage outlet

- chain is overtensioned -> adjust chain tension

- dull chain -> sharpen chain or replace

★ Tool vibrates abnormally

- chain tension too loose -> adjust chain tension

- dull chain -> sharpen chain or replace

- chain worn out -> replace chain

- chain teeth are facing in the wrong direction ->

reassemble with chain in correct direction

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2002/96/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol 8 will remind you of this when the need for

disposing occurs

DECLARATION OF CONFORMITY

• We declare under our sole responsibility that this product is

in conformity with the following standards or standardized

documents: EN 60745, EN 61000, EN 55014 in accordance

with the provisions of the directives 2006/95/EC,

2004/108/EC, 2006/42/EC, 2000/14/EC

• Technical file at: SKIL Europe BV (PT-SEU/PJE),

4825 BD Breda, NL

ÊÆÇÎ¹Æ¼½ÊÄÇÇÌ

Á»½Ê½ËÁ¼½ÆÌ

È½Ê¹ÌÁÇÆËŵÆ¿ÁÆ½½ÊÁÆ¿

ÍÊÇÈ½Ɠˁ˅ʿ˂Ê½¼¹Ɠ

¹ÆÊÇÅÅ½Ä½Æ

ÈÈÊÇÎ¹Ä¹Æ¹¿½Ê

12.04.2011

NOISE/VIBRATION

• Measured in accordance with EN 60745 the sound

pressure level of this tool is 87 dB(A) and the sound power

level 107 dB(A) (standard deviation: 3 dB), and the vibration

4.7 m/s² (hand-arm method; uncertainty K = 1.5 m/s²)

• Measured in accordance with 2000/14/EC

(EN/ISO 3744) the guaranteed sound power level LWA

is lower than 110 dB(A) (conformity assessment

procedure according to Annex VI)

Notied body : KEMA, Arnhem, NL

Notied body identication number : 0344

• The vibration emission level has been measured in

accordance with a standardised test given in EN 60745;

it may be used to compare one tool with another and as

a preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintainted accessories, may signicantly

increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level

! protect yourself against the effects of vibration

by maintaining the tool and its accessories,

keeping your hands warm, and organizing

your work patterns



Tronçonneuse à chaîne 0780

INTRODUCTION

• L’outil électrique est conçu pour scier le bois, comme

par ex. les poutres en bois, les planches, les branches,

les tronçons ainsi que pour abattre des arbres; il peut

être utilisé pour des coupes dans et contre le sens

des bres du bois

• Cet outil n’est conçu pour un usage professionnel

• Vériez que le conditionnement contient toutes les

pièces présentées dans le schéma 2

• Lorsque des pièces manquent ou sont endommagées,

veuillez contacter votre distributeur

• Lisez attentivement ce manuel d’instruction avant

d’utiliser l’outil et conservez-le pour pouvoir vous

y référer ultérieurement 3

• Prêtez attention aux consignes de sécurité et aux

avertissements; ne pas suivre ces instructions peut

entraîner des graves blessures

SPECIFICATIONS TECHNIQUES 1

ELEMENTS DE L’OUTIL 2

A Capot

B Bouton de verrouillage

C Chaîne

D Guide

E Symbole sens de rotation et de coupe

F Pignon de chaîne

G Boulon de xation

H Goupilles de positionnement du guide

J Goupille de tension de chaîne

K Bouton de régulation de la tension de chaîne

L Buse d’huile

M Couvercle réservoir d’huile

Page is loading ...

Skil 0780 AA Owner's manual

This manual is also suitable for

Skil 0780 AA Owner's manual

in other languages

Related papers