DeWalt D28490 T 1 Owner's manual

Page is loading ...

2

Copyright DEWALT

Dansk 6

Deutsch 13

English 21

Español 29

Français 37

Italiano 45

Nederlands 53

Norsk 61

Português 68

Suomi 76

Svenska 83

Türkçe

90

Ελληνικά 97

Page is loading ...

21

ENGLISH

ANGLE GRINDER

D28490/D28491/D28492(K)/D28493

Congratulations!

You have chosen a D E WALT tool. Years of experience, thorough product development and innovation

make D

E WALT one of the most reliable partners for professional power tool users.

Technical data

D28490 D28491 D28492(K) D28493

Voltage V 230 230 230 230

(U.K. & Ireland only) V 230/115230 230/115 230/115

Power input W 2,000 2,000 2,200 2,200

No-load speed min

-1

6,500 8,500 6,500 8,500

Wheel diameter mm 230 180 230 180

Spindle diameter M14 M14 M14 M14

Weight kg 4.6 4.6 4.6 4.6

Fuses:

Europe 230 V tools 10 Amperes, mains

U.K. & Ireland 230 V tools 13 Amperes, in plugs

U.K. & Ireland 115 V tools 16 Amperes, mains

The following symbols are used throughout this manual:

@

Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of

the instructions in this manual.

!

Denotes risk of electric shock.

22

ENGLISH

Director Engineering and Product Development

Horst Großmann

D E WALT, Richard-Klinger-Straße 11

D-65510, Idstein, Germany

Safety instructions

When using power tools, always observe the

safety regulations applicable in your country to

reduce the risk of ﬁ re, electric shock and

personal injury.

Read all of this manual carefully before

operating the tool.

Save this manual for future reference.

General

1 Keep work area clean

Cluttered areas and benches can cause

accidents.

2 Consider work area environment

Do not expose the tool to rain. Do not use the

tool in damp or wet conditions. Keep the work

area well lit (250 - 300 Lux). Do not use the tool

where there is a risk of causing ﬁ re or

explosion, e.g. in the presence of ﬂ ammable

liquids and gases.

3 Keep children away

Do not allow children, visitors or animals to

come near the work area or to touch the tool or

the mains cable.

4 Dress properly

Do not wear loose clothing or jewellery,

as these can be caught in moving parts.

Wear protective hair covering to keep long hair

out of the way.

EC-Declaration of conformity

%

D28490/D28491/D28492(K)/D28493

D

E WALT declares that these power tools have been designed in compliance with: 98/37/EC, 89/336/EEC,

73/23/EEC, 86/188/EEC, EN 50144-1, EN 50144-2-3, EN 55014-2, EN 55014-1, EN 61000-3-2 &

EN 61000-3-3.

For more information, please contact D

E WALT at the address below, or refer to the back of the manual.

Level of sound pressure:

D28490 D28491 D28492(K) D28493

L

pA

(sound pressure) dB(A) 92 92 92 92

L

WA

(acoustic power) dB(A) 103 103 103 103

K

pA

(sound pressure uncertainty) dB(A) 3

K

WA

(acoustic power uncertainty) dB(A) 3

Weighted root mean square acceleration value:

D28490 D28491 D28492(K) D28493

Measured according to EN 50144 m/s

2

5.2 4.2 4.7 4.1

23

ENGLISH

When working outdoors, preferably wear

suitable gloves and non-slip footwear.

5 Personal protection

Always use safety glasses. Use a face or dust

mask whenever the operations may produce

dust or ﬂ ying particles. If these particles might

be considerably hot, also wear a heat-resistant

apron. Wear ear protection at all times. Wear a

safety helmet at all times.

6 Guard against electric shock

Prevent body contact with earthed surfaces

(e.g. pipes, radiators, cookers and refrigerators).

When using the tool under extreme conditions

(e.g. high humidity, when metal swarf is being

produced, etc.), electric safety can be improved

by inserting an isolating transformer or a (FI)

earth-leakage circuit-breaker.

7 Do not overreach

Keep proper footing and balance at all times.

8 Stay alert

Watch what you are doing. Use common sense.

Do not operate the tool when you are tired.

9 Secure workpiece

Use clamps or a vice to hold the workpiece. It is

safer and it frees both hands to operate the tool.

10 Connect dust extraction equipment

If devices are provided for the connection of

dust extraction and collection facilities, ensure

that these are connected and properly used.

11 Remove adjusting keys and wrenches

Always check that adjusting keys and wrenches

are removed from the tool before operating the

tool.

12 Extension cables

Before use, inspect the extension cable and

replace if damaged. When using the tool

outdoors, only use extension cables intended

for outdoor use and marked accordingly.

13 Use appropriate tool

The intended use is described in this instruction

manual. Do not force small tools or attachments

to do the job of a heavy-duty tool. The tool will

do the job better and safer at the rate for which

it was intended. Do not force the tool.

Warning! The use of any accessory or

attachment or performance of any operation

with this tool other than those recommended in

this instruction manual may present a risk of

personal injury.

14 Check for damaged parts

Before use, carefully check the tool and mains

cable for damage. Check for misalignment and

seizure of moving parts, breakage of parts,

damage to guards and switches and any other

conditions that may affect its operation.

Ensure that the tool will operate properly and

perform its intended function. Do not use the

tool if any part is damaged or defective. Do not

use the tool if the switch does not turn it on and

off. Have any damaged or defective parts

replaced by an authorised D

E WALT repair

agent. Never attempt any repairs yourself.

15 Unplug tool

Switch off and wait for the tool to come to a

complete standstill before leaving it unattended.

Unplug the tool when not in use, before

changing any parts of the tools, accessories or

attachments and before servicing.

16 Avoid unintentional starting

Do not carry the tool with a ﬁ nger on the switch.

Be sure that the tool is switched off before

plugging in.

17 Do not abuse cord

Never carry the tool by its cord. Never pull the

cord to disconnect from the socket. Keep the

cord away from heat, oil and sharp edges.

18 Store idle tools

When not in use, tools must be stored in a dry

place and locked up securely, out of reach of

children.

19 Maintain tools with care

Keep the tools in good condition and clean for

better and safer performance. Follow the

instructions for maintenance and changing

accessories. Keep all handles and switches dry,

clean and free from oil and grease.

20 Repairs

This tool is in accordance with the relevant

safety regulations. Have your tool repaired by

an authorised D

E WALT repair agent. Repairs

should only be carried out by qualiﬁ ed persons

using original spare parts; otherwise this may

result in considerable danger to the user.

Additional safety rules for grinders

● Your grinder has been designed for grinding

and cutting masonry and steel.

24

ENGLISH

&

Do not cut or grind light metal with a

magnesium content exceeding 80%

since this type of metal is ﬂ ammable.

● Do not use any accessories other than ﬁ bre

reinforced grinding and cutting discs.

● Use only plain or depressed-centre grinding

and cutting discs.

● Use the grinding and cutting discs recommended

by the manufacturer only.

● The max. allowable speed of the grinding wheel

or cutting disc, or any other suitable accessory,

must always be equal to or greater than the

no-load speed of the tool speciﬁ ed on the

nameplate.

● Do not cut workpieces requiring a maximum

depth of cut exceeding that of the cutting disc.

● Do not use grinding and cutting discs that do

not conform to the dimensions stated in the

technical data. Do not use any spacers to make

a disc ﬁ t onto the spindle. Do not separate

reducing bushings or adapters to adapt large-

hole abrasive wheels.

● Inspect grinding and cutting discs before each

use. Do not use chipped, cracked or otherwise

defective discs.

● If provided, ensure that blotters are used when

the disc is ﬁ tted onto the spindle.

● When applying a threaded hole disc, ensure that

the thread is long enough to accept the spindle.

● Ensure that the grinding or cutting disc is

mounted correctly before use.

● Let the tool run at no-load in a safe position for

at least 30 seconds. If there is a considerable

vibration or if any other defect occurs, stop the

tool and check it to determine the cause.

● Do not operate this tool without the guard in place.

● Check that the workpiece is properly supported.

● Do not operate the tool near ﬂ ammable liquids,

gases or dust. Sparks or hot chips from cutting

or arcing motor brushes may ignite combustible

materials.

● Do not operate the tool while standing in line

with the disc. Keep other persons away from

the work area.

● Do not use cutting discs for side grinding.

● Do not operate the spindle lock while the tool is

running.

● Beware that after switching off the tool the

wheel continues to rotate for a short period.

● Always store grinding and cutting discs

in a dry place.

Labels on tool

The following pictographs are shown on the tool:

+

Read the instruction manual before use

F

Wear safety glasses

f

Wear ear protection

Package contents

The package contains:

1 Angle grinder

1 Guard

1 Side handle

1 Flange set

1 Two-pin spanner

1 Kitbox (K-models only)

1 Instruction manual

1 Exploded drawing

● Check for damage to the tool, parts or

accessories which may have occurred during

transport.

● Take the time to thoroughly read and

understand this manual prior to operation.

Description (ﬁ g. A)

Your angle grinder D28490/D28491/D28492(K)/

D28493 has been designed for professional

grinding and cutting applications.

1 On/off switch

2 Locking switch (not for France)

3 Unlocking switch

4 Spindle lock

5 Guard

6 Side handle

Electrical safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

25

ENGLISH

#

Your D E WALT tool is double insulated in

accordance with EN 50144;

therefore no earth wire is required.

@

115 V units have to be operated via a

failsafe isolating transformer with an

earth screen between the primary and

secondary winding.

Mains plug replacement

(U.K. & Ireland only)

● Should your mains plug need replacing and you

are competent to do this, proceed as instructed

below. If you are in doubt, contact an authorized

D

E WALT repair agent or a qualiﬁ ed electrician.

● Disconnect the plug from the supply.

● Cut off the plug and dispose of it safely; a plug

with bared copper conductors is dangerous if

engaged in a live socket outlet.

● Only ﬁ t 13 Amperes BS1363A approved plugs

ﬁ tted with the correctly rated fuse (1).

● The cable wire colours, or a letter, will be

marked at the connection points of most good

quality plugs. Attach the wires to their

respective points in the plug (see below). Brown

is for Live (L) (2) and Blue is for Neutral (N) (4).

● Before replacing the top cover of the mains plug

ensure that the cable restraint (3) is holding the

outer sheath of the cable ﬁ rmly and that the two

leads are correctly ﬁ xed at the terminal screws.

!

Never use a light socket.

Never connect the live (L) or neutral (N)

wires to the earth pin marked E or

.

For 115 V units with a power rating exceeding

1500 W, we recommend to ﬁ t a plug to BS4343

standard.

Using an extension cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

machine (see technical data). The minimum

conductor size is 1.5 mm

2

. The cable has to have a

rubber jacket and a grounding conductor.

When using a cable reel, always unwind the cable

completely.

Also refer to the table below.

Conductor size (mm

2

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0 - 2.0 6 6 6 6 6 10

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Fitting a mains plug to 115 V units

(U.K. & Ireland only)

● The plug should be ﬁ tted by a competent

person. If you are in doubt, contact an

authorized D

E WALT repair agent or a qualiﬁ ed

electrician.

The wires are coloured according to the following

code:

live = brown

neutral = blue

● Do not connect the blue or brown wire to the

earth terminal in the plug. Connect as follows:

brown to terminal marked ‘L'

blue to terminal marked ‘N'

The plug ﬁ tted should comply with BS EN 60309

(BS4343), 32 Amps.

26

ENGLISH

!

Always ensure that the cable clamp is

correctly and securely ﬁ tted to the

sheath of the cable.

Assembly and adjustment

@

Prior to assembly and adjustment

always unplug the tool.

Mounting and removing the guard (ﬁ g. B)

● Place the angle grinder on a table, spindle up.

● Align the lugs (7) with the notches (8).

● Press the guard (5) down and rotate it to the

required position.

● Securely tighten the screw (9).

● To remove the guard, slacken the screw.

@

Never use the tool without the guard in

place.

Fitting and removing a grinding or cutting disc

(ﬁ g. C1 & C2)

● Place the tool on a table, guard up.

● Fit the inner ﬂ ange (10) correctly onto the

spindle (11) (ﬁ g. C1).

● Place the disc (12) on the ﬂ ange (10).

When ﬁ tting a disc with a depressed centre,

make sure that the depressed centre (13) is

facing the ﬂ ange (10).

● Screw the outer ﬂ ange (14) onto the spindle (11)

(ﬁ g. C2):

- the ring on the ﬂ ange (14) must face towards

the disc when ﬁ tting a grinding disc (A);

- the ring on the ﬂ ange (14) must face away

from the disc when ﬁ tting a cutting disc (B).

● Press the spindle lock (4) and rotate the spindle

(11) until it locks in position.

● Tighten the ﬂ ange (14) with the two-pin spanner

supplied.

● Release the spindle lock.

● To remove the disc, loosen the ﬂ ange (14) with

the two-pin spanner.

@

Do not use a damaged disc.

Fitting a wire cup brush

● Screw the wire cup brush directly onto the

spindle without the use of the spacer and

threaded ﬂ ange.

Mounting the side handle (ﬁ g. D)

● Screw the side handle (6) tightly into one of the

holes (15) on either side of the gear case.

Holding the tool (ﬁ g. E)

● Hold the tool as shown.

@

● For your own safety, always use the

tool with both hands.

● Always wear regular working gloves

while operating this tool.

● Warning: The gear case becomes very

hot during use.

Instructions for use

@

● Always observe the safety instructions

and applicable regulations.

● Ensure all materials to be ground or cut

are secured in place.

● Apply only a gentle pressure to the tool.

Do not exert side pressure on the

grinding wheel or cutting disc.

● Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Prior to operation:

● Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

● Be sure the inner and outer ﬂ ange are mounted

correctly.

● Make sure the disc or wheel rotates in the

direction of the arrows on the accessory and

the tool.

Switching on and off (ﬁ g. A)

The on/off switch is equipped with an unlocking

switch or a locking switch for continuous operation.

On/off switch (1) with locking switch (2)

● To run the tool, depress the unlocking switch (3)

and subsequently operate the on/off switch (1).

27

ENGLISH

Release the unlocking switch (3).

● For continuous operation, press and hold down

the switch (1), press the lock-on button (2) and

release the switch.

● To stop the tool, release the switch.

● To stop the tool in continuous operation, press

the switch brieﬂ y and release it. Always switch

off the tool when work is ﬁ nished and before

unplugging.

On/off switch (1) with unlocking switch (3)

(France only)

● To run the tool, depress the unlocking switch (3)

and subsequently operate the on/off switch (1).

Release the unlocking switch (3).

● To stop the tool, release the switch.

@

Do not switch the tool on or off when

under load.

Metal applications

● When using the tool in metal applications, make

sure that a residual current device (RCD) has

been inserted to avoid residual risks caused by

metal swarf.

● If the power supply is shut off by the RCD, take

the tool to authorised D

E WALT repair agent.

!

In extreme working conditions,

conductive dust can accumulate inside

the machine housing when working with

metal. This can result in the protective

insulation in the machine becoming

degraded with a potential risk of an

electrical shock.

To avoid build-up of metal swarf inside the

machine, we recommend to clear the ventilation

slots on a daily basis. See "Maintenance".

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your D E WALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

A

Lubrication

Your power tool requires no additional lubrication.

S

Cleaning

Keep the ventilation slots clear and regularly clean

the housing with a soft cloth.

Clearing the ventilation slots

To avoid build-up of dust inside the machine,

we recommend to clear the ventilation slots on

a daily basis.

● Unplug the machine.

● Blow dry compressed air through the ventilation

slots.

● Clear the ventilation slots using a soft brush or

dry cloth. Do not use metallic objects as these

might damage the internal parts.

Protecting the environment

Z

Separate collection. This product must

not be disposed of with normal

household waste.

Should you ﬁ nd one day that your D E WALT product

needs replacement, or if it is of no further use to

you, do not dispose of it with household waste.

Make this product available for separate collection.

z

Separate collection of used products

and packaging allows materials to be

recycled and used again. Re-use of

recycled materials helps prevent

environmental pollution and reduces

the demand for raw materials.

Local regulations may provide for separate

collection of electrical products from the

household, at municipal waste sites or by the

retailer when you purchase a new product.

D E WALT provides a facility for the collection and

recycling of D

E WALT products once they have

28

ENGLISH

reached the end of their working life. To take

advantage of this service please return your

product to any authorised repair agent who will

collect them on our behalf.

You can check the location of your nearest

authorised repair agent by contacting your local

D

E WALT ofﬁ ce at the address indicated in this

manual. Alternatively, a list of authorised D

E WALT

repair agents and full details of our after-sales

service and contacts are available on the Internet

at: www.2helpU.com

GUARANTEE

● 30 DAY NO RISK SATISFACTION GUARANTEE ●

If you are not completely satisﬁ ed with the

performance of your D

E WALT tool, simply return

it within 30 days, complete as purchased, to the

point of purchase, for a full refund or exchange.

Proof of purchase must be produced.

● ONE YEAR FREE SERVICE CONTRACT ●

If you need maintenance or service for your

D

E WALT tool, in the 12 months following

purchase, it will be undertaken free of charge at

an authorized D

E WALT repair agent.

Proof of purchase must be produced. Includes

labour and spare parts for Power Tools.

Excludes accessories.

● ONE YEAR FULL WARRANTY ●

If your D E WALT product becomes defective due

to faulty materials or workmanship within

12 months from the date of purchase, we

guarantee to replace all defective parts free of

charge or, at our discretion, replace the unit free

of charge provided that:

● The product has not been misused.

● Repairs have not been attempted by

unauthorized persons.

● Proof of purchase date is produced.

This guarantee is offered as an extra beneﬁ t

and is additional to consumers statutory

rights.

For the location of your nearest authorized

D

E WALT repair agent, please use the

appropriate telephone number on the back of

this manual. Alternatively, a list of authorized

D

E WALT repair agents and full details on our

after-sales service are available on the Internet

at www.2helpU.com .

Page is loading ...

Belgique et Luxembourg DEWALT Tel: +32 (0)015 - 15 47 9211

België en Luxemburg Mechelen Campus, Schaliënhoevedreef 20

E

Fax: +32 (0)015 - 15 47 9210

B-2800 Mechelen www.dewalt.com

Danmark D

EWALT Tlf: 70 20 15 10

Sluseholmen 2-4 Fax: 36 94 49 01

2450 København SV www.dewalt-nordic.com

Deutschland D

EWALT Tel: 06126-21-1

Richard-Klinger-Straße Fax: 06126-21-2770

65510 Idstein www.dewalt.de

Ελλάς Black & Decker (Hellas) S.A. Τηλ: (01) 8981-616

Στράβωνος 7 & Βουλιαγμένης 159 Φαξ: (01) 8983-570

Γλυφάδα 16674, Αθήνα Service: (01) 8982-630

España D

EWALT Tel: 934 797 400

Parque de Negocios “Mas Blau” Fax: 934 797 439

Ediﬁ cio Muntadas, c/Bergadá, 1, Of. A6

08820 El Prat de Llobregat (Barcelona)

France D

EWALT Tel: 472 20 39 72

Le Paisy Fax: 472 20 39 02

BP 21, 69571 Dardilly Cedex www.dewalt.fr

Schweiz DeWALT Tel: 01 - 730 67 47

Suisse In der Luberzen 40 Fax: 01 - 730 70 67

Svizzera 8902 Urdorf www.dewalt.ch

Ireland D

EWALT Tel: 00353-2781800

Calpe House Rock Hill Fax: 00353-2781811

Black Rock, Co. Dublin www.dewalt.ie

Italia D

EWALT Tel: 800-014353

Viale Elvezia 2 Fax: 039-2387592

20052 Monza (Mi) www.dewalt.it

Nederland D

EWALT BV Tel: 0164 283000

Joulehof 12 Fax: 0164 283100

4622 RG Bergen Op Zoom www.dewalt.com

Norge D

EWALT Tel: 22 90 99 00

Postboks 4814, Nydalen Fax: 22 90 99 01

0422 Oslo www.dewalt-nordic.com

Österreich D

EWALT Tel: 01 - 66116 - 0

Werkzeugevertriebs GmbH Fax: 01 - 66116 - 14

Erlaaerstraße 165, Postfach 320,1231 Wien www.dewalt.at

Portugal D

EWALT Tel: 214 66 75 00

Rua Egas Moniz 173 Fax: 214 66 75 75

João do Estoril, 2766-651 Estoril

Suomi D

EWALT Puh: 010 400 430

Keilasatama 3 Faksi: (09) 2510 7100

02150 Espoo www.dewalt-nordic.com

D

EWALT Tel: 010 400 430

Kägelhamnen 3 Fax: (09) 2510 7100

02150 Esbo www.dewalt-nordic.com

Sverige D

EWALT, c/o Regus Tel: 031 68 61 00

Fabriksgatan 7 Fax: 031 68 60 08

412 50 Göteborg www.dewalt-nordic.com

Türkiye

Merkez Servis

Tel:

0212 361 60 20

Tersane Cad.

Faks:

0212 361 60 19

Nafe Sokak 1-3/4 Karaköy - İstanbul

United Kingdom D

EWALT Tel: 01753-56 70 55

210 Bath Road Fax: 01753-57 21 12

Slough, Berks SL1 3YD www.dewalt.co.uk

640921-00

07/06

DeWalt D28490 T 1 Owner's manual

DeWalt D28490 T 1 Owner's manual

in other languages

Related papers

Other documents