Cullmann CUlight FR 60N User manual

Brand: Cullmann

Model: CUlight FR 60N

Category: Camera flashes

Type: User manual

This manual is also suitable for

CUlight FR 60S

FR 60S

for Sony

616x0_CUlight_FR60X_BDA_Sony englisch.indd 31 24.10.2016 13:59:15

Foreword

Thank you for purchasing this product.

This CUlight FR 60S camera ash applies to Sony DSLR series

cameras and is compatible with TTL autoash. With this TTL

compatible ash, your shooting will become simpler. You

can easily achieve a correct ash exposure even in complex

light-changing environments. This camera ash features:

• GN60 (m ISO 100, @200mm). 22 steps from 1/1 to 1/128.

• Fully support Sony TTL camera ash. Workable as Master or

Slave unit in a wireless ash group.

• Use dot-matrix LCD panel to make clear and convenient

operations.

• With built-in 2.4GHz wireless remote system to support

transmitting and receiving.

• Provided multiple functions, include HSS (up to 1/8000s),

FEC, etc.

• Stable consistency and color temperature with good even

lighting.

• Support with rmware upgrade.

616x0_CUlight_FR60X_BDA_Sony englisch.indd 32 24.10.2016 13:59:15

For Your Safety

Always keep this product dry. Do not use in rain or in damp

conditions.

This product contains high-voltage electronic parts. Touching

the high-voltage circuit inside it may result in electric shock.

Do not disassemble. Should repairs become necessary, this

product must be sent to an authorized maintenance center.

Stop using this product if it breaks open due to extrusion,

falling or strong hit. Otherwise, electric shock may occur if

you touch the electronic parts inside it.

Do not re the ash directly into the eyes (especially those of

babies) within short distances. Otherwise visual impairment

may occur. When taking pictures for babies, keep the ash

unit at least 1 meter (3.3 feet) away from them. Using bounce

ash to reduce light intensity is also recommended.

Do not use the ash unit in the presence of ammable

gases, chemicals and other similar materials. In certain cir-

cumstances, these materials may be sensitive to the strong

light emitting from this ash unit and re or electromagnetic

interference may result.

Do not leave or store the ash unit in places where the

ambient temperature reads over 50°C (e.g. in automobile).

Otherwise the electronic parts may be damaged.

616x0_CUlight_FR60X_BDA_Sony englisch.indd 33 24.10.2016 13:59:16

Conventions used in this Manual

• This manual is based on the assumption that both the camera

and camera ash’s power switches are powered on.

• Reference page numbers are indicated by “p.**”.

• The following alert symbols are used in this manual:

The Caution symbol gives supplemental information.

The Note symbol indicates a warning to prevent shooting

problem.

616x0_CUlight_FR60X_BDA_Sony englisch.indd 34 24.10.2016 13:59:16

Contents

Foreword ..................................32

For Your Safety .............................33

Name of Parts ..............................36

Body ......................................36

Control Panel ................................ 36

LCD Panel ..................................37

What’s in the Box of CUlight FR 60S? ............38

Separately Sold Accessories ...................38

Attaching to a Camera .......................39

Power Management ......................... 39

TTL Flash Mode ............................40

FEC: Flash Exposure Compensation ..........40

High-Speed Sync ..........................41

 Second-Curtain Sync ......................41

M: Manual Flash ............................42

Multi: Stroboscopic Flash ....................43

Wireless Flash Shooting: ....................44

Optic Transmission .........................44

1. Wireless Settings ..........................45

2. Setting Master Unit‘s Flash Mode .............45

3. Setting the Communication Channel ...........46

Wireless Shooting: 2.4GHz Transmission ......46

1. Wireless Settings ..........................46

2. Setting Master Unit’s Flash Mode .............47

3. Setting the Communication Channel ...........47

4. TTL: Fully Automatic Wireless Flash Shooting ...47

5. M: Wireless Flash Shooting with Manual Flash ... 49

6. Multi: Manual Wireless Flash Shooting .........49

Other Applications .......................... 51

Sync Triggering ..............................51

Auto Focus Assist Beam ......................51

Bounce Flash ...............................52

Creating a Catchlight .......................... 52

ZOOM: Setting the Flash Coverage

and Using the Wide Panel .....................53

Using the Wide Panel .........................53

Low Battery Warning .........................53

Factory Settings .............................53

C.Fn: Setting Custom Functions ..............54

Protection Function .........................55

1. Over-Temperature Protection .................55

2. Other Protections ..........................55

Technical Data ..............................56

Troubleshooting ............................57

Firmware Upgrade ..........................58

Compatible Camera Models ..................58

Maintenance ...............................58

Declaration of Conformity ...................58

616x0_CUlight_FR60X_BDA_Sony englisch.indd 35 24.10.2016 13:59:16

Name of Parts

• Body

01. Catchlight Panel

02. Built-in Wiede Panel

03. Flash Head

04. Optic Control Sensor

05. Focus Assist Beam

06. Sync Cord Jack

07. Hotshoe

08. Dot-matrix LCD Panel

09. Lock Ring

10. Battery Compartment

11. USB Port

12. Slave Flash Ready Indicator

13. External Power Supply Socket

• Control Panel

15. <MODE> Mode Selection

Button / Lock button

16. <R> Wireless Selection

Button

17. Select Dial

18. <SET> Set Button

19. ON/OFF Power Switch

20. <

> Test Button /

Flash Ready Indicator

21. Function Button 1

22. Function Button 2

23. Function Button 3

24. Function Button 4

RST

SET

616x0_CUlight_FR60X_BDA_Sony englisch.indd 36 24.10.2016 13:59:16

• LCD Panel

• The display will only show the settings currently applied.

• The functions displayed above functions buttons 1 to 4, such as

SYNC

and , change according to settings‘ status.

• When a button or dial is operated, the LCD panel illuminated.

• (2) M Manual Flash

M: Manual ash

Manual ash output

• (3) Multi Flash

Multi: Stroboscopic

ash

Number of ashes

Flash frequency

(1) TTL Autoash

Zoom: zoom display

(Page 53)

TTL: TTL autoash

Flash exposure

compensation

(Page 40)

Focus length

(Page 53)

 High-speed sync

(Page 41)

Distance indicator

display

: Automatic

: Manual (Page 42)

Flash exporure

compensation

amount

616x0_CUlight_FR60X_BDA_Sony englisch.indd 37 24.10.2016 13:59:17

•What’s in the Box of CUlight FR 60S?

1. Flash unit

2. Mini stand

3. Protection case

4. Instruction manual

•Separately Sold Accessories

The product can be used in combination with the following

separately sold accessories:

1. CUlight 2.4 GHz Trigger Kit RT 500S & RR 500S

2. CUlight 2.4 GHz Transmitter RT 500S

3. CUlight 2.4 GHz Receiver RR 500S

4. CUlight Power Pack PP 4500

5. CUlight Power Pack Battery B 4500

6. CUlight Power Pack Cable PC 150S

7. CUlight Softbox Kit with Flashgun Holder SB 40-40 Kit

8. CUlight Softbox Kit with Flashgun Holder SB 60-60 Kit

9. CUlight Light Stand LS 2000 (200cm)

10. CUlight Light Stand LS 2500 (300cm)

(4) Radio Transmission Shooting /

Optic Transmission Shooting

•Master Unit

Flash mode

GR: Group ash

(radio transmission)

 Radio transmission

wireless shooting

 Optic transmission

wireless shooting

Firering group

Channel

•Slave Unit

Slave icon

: Slave

FEC

616x0_CUlight_FR60X_BDA_Sony englisch.indd 38 24.10.2016 13:59:17

Attaching to a Camera

C.Fn

Attaching to a Camera

Attach the Camera Flash.

● Slip the camera flash’s

mounting foot into the

camera’s hotshoe all the

way.

Secure the Camera Flash.

● Rotate the lock ring on the

mounting foot until it locks

up.

Detach the Camera Flash.

● Rotate the lock ring on the

mounting foot until it is

loosened.

Power Management

Use ON/OFF Power Switch to power the flash unit on or off. Turn off

if it will not be used for an extended period of time. Setting as a

master flash, it will turn the power off automatically after a certain

period (approx. 90 seconds) of idle use. Pressing the camera

shutter halfway or pressing any flash button will wake up the flash

unit. Setting as a slave flash, it will enter sleep mode after a certain

period (adjustable, 60 minutes by default) of idle use. Pressing any

flash button will wake it up.

Disabling Auto Power Off function is recommended

when the flash is used off camera. (C.Fn-APO, Page 74)

Slave Auto Power Off Timer is set to 60 minutes by

default. Another option “30 minutes” is available. (C.Fn-

Sv APOT, Page 74)

FEC: Flash Exposure Compensation

With FEC function, this flash can adjust from -3 to +3 in 1/3rd stops.

It is useful in situations where minor adjusting of the TTL system is

needed based on the environment.

Setting FEC:

Set the flash exposure

2 compensation amount.

● Turn the Select Dial to set

the amount.

● “0.3”means 1/3 step,

“0.7”means 2/3 step.

● To cancel the flash

exposure compensation,

set the amount to “+0”.

Press < SET > button again

3 to confirm the setting.

Press Function Button 2

1 < >. The icon < >

and flash exposure

compensation amount will be

highlighted on the LCD

panel.

FEB: Flash Exposure Bracketing

You can take three flash shots while automatically changing the

flash output for each shot from -3 to +3 in 1/3rd stops. The camera

will record three images with different exposures: one exposed

according to camera calculations, one over-exposed and another

under-exposed. Over and under exposure amount is user

adjustable. This function helps get correct exposure especially in

shooting moving objects or when environmental lights are complex.

Flash Mode—E-TTL Autoflash

This flash has three flash modes: E-TTL, Manual (M), and Multi

(Stroboscopic). In E-TTL mode, the camera and the flash will work

together to calculate the correct exposure for the subject and the

background. In this mode, multiple TTL functions are available:

FEC, FEB, FEL, HSS, second curtain sync, modeling flash, control

with the camera’s menu screen.

* Press < MODE > Mode Selection Button and three flash modes

will display on the LCD panel one by one with each pressing.

ETTL Mode

Press < MODE > Mode Selection Button to enter E-TTL mode. The

LCD panel will display.

● Press the camera release button halfway to focus. The aperture

and effective flash range will be displayed in the viewfinder.

● When the shutter button is fully pressed, the flash will fire a pre-

flash that the camera will use to calculate exposure and flash

output the instant before the photo is taken.

- 47 -

- 48 -

 Attach the Camera Flash.

• Slip the camera ash’s

mounting foot into the cam-

era’s hotshoe all the way.

 Secure the Camera Flash.

• Rotate the lock ring on

the mounting foot until it

locks up.

 Detach the Camera Flash.

• Rotate the lock ring on the

mounting foot until it is

loosened.

Power Management

Use ON/OFF Power Switch to power the ash unit on or off.

Turn off if it will not be used for an extended period of time.

Setting as a master ash, it will turn the power off automatically

after a certain period (approx. 90 seconds) of idle use. Pressing

the camera shutter halfway or pressing any ash button will

wake up the ash unit. Setting as a slave ash, it will enter sleep

mode after a certain period (adjustable, 60 minutes by default) of

idle use. Pressing any ash button will wake it up.

C.Fn

 Disabling Auto Power Off function is recommend-

ed when the ash is used off camera. (C.Fn-APO,

page 54)

C.Fn

 Slave Auto Power Off Timer is set to 60 minutes

by default. Another option “30 minutes” is availa-

ble. (C.Fn- Sv APOT, page 54)

616x0_CUlight_FR60X_BDA_Sony englisch.indd 39 24.10.2016 13:59:18

TTL Flash Mode

This ash has three ash modes: TTL, Manual (M), and Multi

(Stroboscopic). In TTL mode, the camera and the ash will work

together to calculate the correct exposure for the subject and the

background. In this mode, multiple TTL functions are available:

FEC, HSS, second curtain sync, etc.

* Press < MODE > Mode Selection Button and three ash

modes will display on the LCD panel one by one with each

pressing.

TTL Mode

Press < MODE > Mode Selection Button to enter TTL mode.

The LCD panel will display.

• Press the camera release button halfway to focus. The

aperture and effective ash range will be displayed in the

viewnder.

• When the shutter button is fully pressed, the ash will re a

pre-ash that the camera will use to calculate exposure and

ash output the instant before the photo is taken.

FEC: Flash Exposure Compensation

With FEC function, this ash can adjust from -3 to +3 in 1/3rd

stops. It is useful in situations where minor adjusting of the TTL

system is needed based on the environment.

Setting FEC:

 Press Function Button 2

>. The icon

> and ash exposure

compensation amount will

be highlighted on the LCD

panel.

 Set the ash exposure

compensation amount.

• Turn the Select Dial to set

the amount.

• “0.3”means 1/3 step,

“0.7”means 2/3 step.

• To cancel the ash expo-

sure compensation, set the

amount to “+0”.

 Press <SET> button again

to conrm the settings.

616x0_CUlight_FR60X_BDA_Sony englisch.indd 40 24.10.2016 13:59:18

High-Speed Sync

High Speed Sync (FP ash) enables the ash to synchronize with

all camera shutter speeds. This is convenient when you want to

use aperture priority for ll-ash portraits.

As high-speed sync setting is determined by Sony camera’s

shutter, please refer to your camera’s menu.

 Second-Curtain Sync

With a slow shutter speed, you can create a light train following

the subject. The ash res right before the shutter closes.

• Set Sony camera to Rear mode.

• With high-speed sync, the faster the shutter speed, the

shorter the effective ash range.

• Multi ash mode cannot be set in high-speed sync mode.

• Over-temperature protection may be activated after 15

consecutive high-speed sync ashes.

616x0_CUlight_FR60X_BDA_Sony englisch.indd 41 24.10.2016 13:59:18

M: Manual Flash

The ash output is adjustable from 1/1 full power to 1/128th

power in 1/3rd stop increments. To obtain a correct ash

exposure, use a hand-held ash meter to determine the required

ash output.

Press <MODE> button so

thatr <M> is displayed.

Turn the Select Dial to

choose a desired ash output

amount.

Press <SET> button again to

conrm the setting.

Flash Output Range

The following table makes it easier to see how the stop changes

in terms of f/stop when you increase or decrease the ash

output. For example, when you decrease the ash output to 1/2,

1/2-0.3, or 1/2- 0.7, and then increase the ash output to more

than 1/2, 1/2+0.3, 1/2+0.7, and 1/1 will be displayed.

Figures displayed when reducing ash output level.

Figures displayed when increasing ash output level

Optic S1 Secondary Unit Setting

In M manual ash mode, press <S1/S2> button so that this ash

can function as an optic S1 secondary ash with optic sensor.

With this function, the ash will re synchronously when the

main ash res, the same effect as that by the use of radio

triggers. This helps create multiple lighting effects.

Optic S2 Secondary Unit Setting

Press <S1/S2> button so that this ash can also function as an

optic S2 secondary ash with optic sensor in M manual ash

mode. This is useful when cameras have pre-ash function.

With this function, the ash will ignore a single “preash” from

the main ash and will only re in response to the second, actual

ash from the main unit.

Manual Off Camera High-speed Setting

In M manual ash mode, press <

SYNC

>- button to select high-

speed mode and is displayed.

• S1 and S2 optic triggering is only available in M manual

ash mode.

616x0_CUlight_FR60X_BDA_Sony englisch.indd 42 24.10.2016 13:59:18

Multi: Stroboscopic Flash

With stroboscopic ash, a rapid series of ashes is red. It can

be used to capture a multiple images of a moving subject in a

single photograph.

You can set the ring frequency (number of ashes per sec.

expressed as Hz), the number of ashes, and the ash output.

Press <MODE> button so that

<MULTI> is displayed.

Turn the Select Dial to choose

a desired ash output.

Set the ash frequency and

ash times.

• Press <

MULTI

> button to

select the item (blinks).

• Turn the Select Dial to set the

number and press<

> button again to conrm.

The next item to be set will

blink.

• After you nisth the setting,

press <SET> button and all the

settings will be displayed.

Calculating the Shutter Speed

During stroboscopic ash, the shutter remains open until the r-

ing stops. Use the formula below to calculate the shutter speed

and set it with the camera.

Number of Flashes / Flash Frequency = Shutter Speed

For example, if the number of ashes is 10 and the ring fre-

quency is 5 Hz, the shutter speed should be at least 2 seconds.

• Stroboscopic ash is most effective with a highly reec-

tive subject against a dark background.

• Using a tripod and a remote control is recommended.

• A ash output of 1/1 and 1/2 cannot be set for strobo-

scopic ash.

• Stroboscopic ash can be used with“bulb”.

• If the number of ashes is displayed as “--”, the ring will

continue until the shutter closes or the battery is exhaust-

ed. The number of ashes will be limited as shown by the

following table

To avoid overheating and deteriorating the ash head, do

not use stroboscopic ash more than 10 times in succes-

sion. After 10 times, allow the camera ash to rest for at

least 15 minutes. If you try to use the stroboscopic ash

more than 10 times in succession, the ring might stop au-

tomatically to protect the ash head. If this happens, allow

at least 15 minutes’ rest for the camera ash.

616x0_CUlight_FR60X_BDA_Sony englisch.indd 43 24.10.2016 13:59:18

Flash

output

1 2 3 4 5 6-7 8

1/4 7 6 5 4 4 3 3

1/8 14 14 12 10 8 6 5

1/16 30 30 30 20 20 20 10

1/32 60 60 60 50 50 40 30

1/64 90 90 90 80 80 70 60

1/128 90 90 90 90 90 90 80

Flash

output

10 20-50 60-199

1/4 2 2 2

1/8 4 4 4

1/16 8 8 8

1/32 20 16 12

1/64 50 30 20

1/128 70 40 40

Maximum Stroboscopic Flashes

Wireless Flash Shooting:

Optic Transmission

This product is compatible with Sony Wireless Lighting

System (WL). It can function as either an optical wireless

master or slave ash. As a master unit, it can control

Sony camera ashes e.g. HVL-F60M, HVL-F43M and HVL-

F32M via wireless. As a slave unit, it can be controlled by

wireless signals of Sony camera ashes e.g. HVL-F60M,

HVL-F43M and HVL-F32M.

For the restrictions of Sony camera ash’s wireless protocol,

there are several points to be noticed:

• Master unit only has TTL and OFF mode. And M ash mode

can only be set under the slave mode.

• Optical wireless lighting system (WL) do not have Multi mode.

• When setting the slave unit to M mode, plese set the group of

the master unit to TTL mode.

Slave/Master Unit’s Positioning and Operation Range

Indoors

Outdoors

• Even with multiple slave units, the master unit can

control all of them via wireless.

• In this user manual, “master unit” refers to the camera

ash on a camera and “slave unit” will be controlled by

the master unit.

616x0_CUlight_FR60X_BDA_Sony englisch.indd 44 24.10.2016 13:59:18

1. Wireless Settings

You can switch between normal ash and wireless ash. For

normal ash shooting, be sure to set the wireless setting to OFF.

Master Unit Setting

Press <R> button so that

< > and <CTRL+> are

displayed on the LCD panel.

The backlight turns green

now.

Slave Unit Setting

Press <R> button so that

< > and < > are

displayed on the LCD panel.

DThe backlight turns orange

now

Press Function Button 4

> to choose the group

from M/A/B/C. Then, press

Function Button 3 < MODE >

so that the master unit can

work in OFF / TTL ash

mode. Choose one of them

as the ash mode of master

unit.

Flash Mode

SLOW

REAR

Wireless

• Note: In the master unit mode <sCTRL+>, you should

set the camera to wireless lighting mode (WL) when at-

taching the camera ash. If the camera is not set to WL

state, a note „SET YOUR CAMERA“ will be displayed on

the camera ash. As for how to set camera to wireless

lighting mode (WL), please refer tot he camera’s manual.

Exit Optical Wireless Lighting Mode

Flash

Mode

SLOW

REAR

Fill-flash

Set the camera to NON wireless

lighting mode

Press <R> Wireless Selection

Button to switch to other modes.

2. Setting Master Unit‘s Flash Mode

616x0_CUlight_FR60X_BDA_Sony englisch.indd 45 24.10.2016 13:59:19

3. Setting the Communication Channel

If there are other wireless ash systems nearby, you can change

the channel IDs to prevent signal interference. The channel IDs

of the master unit and the slave unit(s) must be set to the same.

Press Function Button 3

> and turn the Select

Dial to choose a channel ID

from 1 to 4.

Press the <SET> button to

conrm.

• Note: As optical lighting system (WL) is restrained to

Sony’s wireless protocol, there is no much room for CU-

light FR 60S to improve its optical transmission mode.

Therefore, radio transmission (2.4G) is recommended

for its easier operation, creative lighting effects, stable

signals, etc.

Wireless Shooting: 2.4GHz Transmission

• You can set up three slave groups for TTL autoash shooting.

With TTL autoash, you can easily create various lighting

effects.

• Any ash settings for the slave units on the master ash in TTL

mode will be automatically sent to the slave units. So the only

thing you need to do is to set the master unit for each slave

group without any operation for the slave units at all during the

shooting.

• This ash can work in TTL /M /Multi / OFF ash modes when

set as a master unit.

1. Wireless Settings

You can switch between normal ash and wireless ash. For

normal ash shooting, be sure to set the wireless setting to OFF.

Master Unit Setting

• Even with multiple slave units, the master unit can

control all of them via wireless.

• In this user manual, “master unit” refers to the camera

ash on a camera and “slave unit” will be controlled by

the master unit.

Press < > button so that

< > is displayed on the

LCD panel. If < MULTI >

mode is ON.

The backlight turns green

now.

616x0_CUlight_FR60X_BDA_Sony englisch.indd 46 24.10.2016 13:59:20

Slave Unit Setting

Press <R> button so that

< > and < > are

displayed on the LCD panel.

The backlight turns orange

now.

2. Setting Master Unit’s Flash Mode

Press Function Button 4

> to choose the group

from M/A/B/C. Then, press

Function Button 3 <MODE>

so that the master unit can

work in OFF/TTL/M ash

mode. Choose one of them

as the ash mode of master

unit.

Press < > button to

switch to Multi mode.

3. Setting the Communication Channel

If there are other wireless ash systems nearby, you can change

the channel IDs to prevent signal interference. The channel IDs

of the master unit and the slave unit(s) must be set to the same.

Press Function Button 3

> and turn the Select

Dial to choose a channel ID

from 1 to 32.

Press the <SET> button to

conrm.

4. TTL: Fully Automatic Wireless

Flash Shooting

Autoash Shooting with One Slave Unit

Master Unit Setting

• Attach a CUlight FR 60S

camera ash on the camera

and set it as the master unit.

(Page 45)

• M/A/B/C can be set as TTL

mode independently.

616x0_CUlight_FR60X_BDA_Sony englisch.indd 47 24.10.2016 13:59:22

Slave Unit Setting

• Set the other ash unit as

the wireless slave Unit.

(Page 47)

• The slave unit can be set

as A/B/C.

Check the communication

channel.

• If the master unit and slave

unit(s) are set to a different

channel, set them to the

same channel. (Page 47)

Position the camera and

ashes.

• Position the camera and

ashes as the picture

shows. (Page 44)

Check that the ash is

ready.

• Check that the master ash

ready indicator is lightened.

• When the slave ash ready

indicator is ready, the

AF-assist beam lighting

area will blinks at 1 second

intervals.

Check the ash operation.

• Press the master unit’s

Test Button < >.

• Then, the slave unit will

re. If not, adjust the slave

unit’s angle toward the

master unit and distance

from the master unit.

• The slave unit might be out of order or re an unwanted

ash due to the nearby uorescent lamp or computer

screen.

• If the slave unit’s auto power off function is workable,

press the master unit’s test button to power it on. Please

note that test ring is unavailable during the camera’s

regular metering time.

• The effective time of slave auto power off is changeable.

(C.Fn-Sv APOT Page 54)

• By making some settings, the auto AF-assist transmitter

will not blink after the slave unit`s ash ready indicator is

lightened. (C.Fn-AF Page 54)

616x0_CUlight_FR60X_BDA_Sony englisch.indd 48 24.10.2016 13:59:23

Using Fully Automatic Wireless Flash

The FEC and other settings that set on the master unit will also

be appeared on the slave unit automatically. The slave unit does

not need any operation. Use the following settings to make

wireless ashes according to the same methods with normal

ash shooting.

• Flash Exposure Compensation (

Page 40)

About Master Unit

Use two or more master units. By preparing several cameras

that with master units ash attached, cameras can be changed

in shooting while keeping the same lighting source (slave unit).

5. M: Wireless Flash Shooting with Man-

ual Flash

This describes wireless (multiple shooting) using manual ash.

You can shoot with a different ash output setting for each slave

unit (ring group). Set all parameters on the master unit.

Setting the ash mode

to <M>.

• Drücken Sie die Funk-

tionstaste 4 <

>, um

Gruppen auszuwählen.

• Press Function Button 4

> to choose groups.

Then, press Function But-

ton 3 <MODE> to set the

ash to M mode.

Setting ash output.

• Press Function Button 2

< >. Turn the Select

Dial to set the ash output

of the groups. Press the

<SET> button to conrm.

Taking the picture.

• Each group res at the set

ash ratio

6. Multi: Manual Wireless Flash Shooting

Setting stroboscopic ash

<MULTI>

• Press <MODE> button

so that < MULTI> is

displayed.

• Press <MODE> button

so that < MULTI> is

displayed.

Using a ash (master/slave) with a radio transmission wireless

shooting function make it easy to shoot with advanced wireless

multiple ash lighting, in the same way as TTL autoash shoot-

ing. The basic relative position and operation range are as shown

in the picture. You can then perform wireless TTL autoash

shooting just by setting the master unit to <TTL>.

616x0_CUlight_FR60X_BDA_Sony englisch.indd 49 24.10.2016 13:59:24

• Slave/Master Unit’s Positioning and Operation Range

Autoash Shooting with One Slave Unit

Transmission distance is

about 100m.

• Use the supplied mini stand to position the slave unit.

• Before shooting, perform a test ash and test shooting.

• The transmission distance might be shorter depending

on the conditions such as positioning of slave units, the

surrounding environment and whether conditions.

Wireless Multiple Flash Shooting

You can divide the slave units into two or three groups and

perform TTL autoash while changing the ash ratio (factor). In

addition, you can set and shoot with a different ash mode for

each ring group, for up to 3 groups.

• Auto Shooting with Two Slave Groups

• Auto Shooting with Three Slave Groups

Wireless shooting using radio transmission has advantages over

wireless shooting using optic transmission, such as being less

616x0_CUlight_FR60X_BDA_Sony englisch.indd 50 24.10.2016 13:59:25

Page is loading ...

Cullmann CUlight FR 60N User manual

Brand: Cullmann

Model: CUlight FR 60N

Category: Camera flashes

Type: User manual

This manual is also suitable for

CUlight FR 60S

Download PDF

report

Cullmann CUlight FR 60N User manual

This manual is also suitable for

Cullmann CUlight FR 60N User manual

Other documents