Canon G20 Hi User manual

Canon INC.

Canon Europa N.V.

P.O. Box 2262, 1180 EG Amstelveen, the Netherlands

Canon UK Ltd

Camera Division, Ribcon Way Luton Bedfordshire LU4 9UR, United Kingdom

Telephone 0870 241 2161

Canon Australia Pty. Ltd

1 Thomas Holt Drive, North Ryde, N.S.W. 2113, Australia

Telephone 805-2000, Fax 887-4484

Canon New Zealand Ltd

Fred Thomas Drive, Takapuna, P.O. Box 33-336, Auckland, New Zealand

Telephone 486-1570, Fax 486-6420

Canon Singapore Pte. Ltd

79 Anson Road #09-01/06, Singapore 079906

Telephone (65)-532-4400, Fax (65)-221-2939

Canon Hongkong Company Ltd

9/F, The Hong Kong Club Building, 3A Chater Road, Central, Hong Kong

Canon Latin America, Inc.

Sales & Enquiries: 6505 Blue Lagoon Drive Suite 325 Miami FL 33126 USA

PUB.DIE-156 © CANON INC. 2001 PRINTED IN KOREA

DY8-9020-092-000 IMPRIME EN COREE

8mm VIDEO CAMCORDER

Instruction Manual E

PAL

This manual explains how to use the G2000/G15Hi and

G20Hi camcorders. In certain areas, all of these three

models may not be available.

Introduction Basic

Operation Advanced

Functions Additional

Information

2

Introduction

E

CAUTION:

CUSTOMERS IN THE U.K. SHOULD READ THIS BEFORE USING THIS PRODUCT.

CHANGING THE FUSE

THE MAINS LEAD ON THIS PRODUCT IS FITTED WITH A NON-REWIREABLE

(MOULDED) PLUG, INCORPORATING A 3 AMP FUSE. SHOULD THE FUSE NEED TO

BE REPLACED AN ASTA OR BSI APPROVED BS1632 FUSE OF THE SAME RATING

MUST BE USED.

ALWAYS REFIT THE FUSE COVER AFTER REPLACING THE FUSE. NEVER USE THE

PLUG WITH THE FUSE COVER OMITTED.

CHANGING THE PLUG

IF THE FITTED PLUG IS NOT SUITABLE FOR YOUR SOCKET OUTLETS, IT SHOULD

BE CUT OFF AND AN APPROPRIATE PLUG FITTED IN ITS PLACE. IF POSSIBLE FIT

AN APPROPRIATE 3 AMP FUSE. IF THE NEW PLUG HAS NO FUSE, THEN FIT A 5

AMP FUSE AT THE DISTRIBUTION BOARD.

AC POWER CORD CONNECTION (CA-550KB only)

The wires in the mains lead of this apparatus are coloured in accordance with the

following cord.

(IMPORTANT)

As the colours of the wires in the mains lead may not correspond with the coloured

markings identifying the terminals in your plug, proceed as follows:The wire which

is coloured BLUE must be connected to the terminal which is marked with the letter

N or coloured black.The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured red. Neither Blue wire or

Brown wire is to be connected to the Earth pin of a 3 pin plug.

THE SEVERED PLUG MUST BE DESTROYED IMMEDIATELY TO AVOID ANY

POSSIBLE ELECTRIC SHOCK HAZARD.

Important Usage Instructions

CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS PRODUCT TO RAIN OR MOISTURE.

CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING

INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.

Mains Lead BLUE..............NEUTRAL

BROWN..........LIVE

3

Introduction

E

Contents

Important Usage Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Thank you for Choosing a Canon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Introducing the Camcorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Finding Your Way Around the G2000/G15Hi/G20Hi . . . . . . . . . . . . . . . . . . . . . . . .6

Powering Your Camcorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Loading a Cassette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Basic Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Zooming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Playing Back a Cassette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Connecting for Playback on a TV Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Tips for Making Better Videos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Selecting from the Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Setting Custom Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Image Stabilizer (G15Hi/G20Hi) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Using the Wireless Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Setting the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Adding Titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Fade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Searching and Reviewing While Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Using the Various Recording Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Focusing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Adjusting the Exposure Manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Taking Still Pictures (Photo Mode) (G20Hi) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Using Digital Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Using the Built-in Video Light (G20Hi) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Simple Editing to a VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Preparing the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Notes on Using the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Video System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Cautions and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Viewfinder Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Introduction

Quick Overview

Advanced Functions

Additional Information

4

Introduction

EFirst, we’d like to thank you for buying

this Canon camcorder. Its advanced

technology makes it very easy to use —

you will soon be making high-quality

home videos which will give you

pleasure for years to come.

To get the most out of your new

camcorder, you should read this manual

thoroughly — there are many

sophisticated features which will add to

your recording enjoyment.

Thank you for Choosing a Canon

WL-85 Wireless

Controller

BP-911K

Battery Pack

CA-550K Compact

Power Adapter

Two Lithium button

battery (CR2025)

SS-500

Shoulder Strap

C-250 AV Cable PC-A5 SCART

Adapter

(Europe and Asia)

Lens cap and lens cap cord

(Attached to camera)

Check that this package contains the

following accessories:

Getting started

To get started we suggest that you

master the basic operations of the

camcorder first, before moving on to

use its full range of features.

For quick reference (in addition to the

contents and index) please refer to:

• Finding Your Way Around the

G2000/G15Hi/G20Hi (p. 6)

• Screen displays (p. 66)

• Troubleshooting — in case you run

into any problems (p. 63)

Note that capital letters are used to

refer to settings that appear in the

display and buttons labeled on the

camcorder itself e.g. Press the EJECT

5button.

5

Introduction

E

Introducing the Camcorder

22×lens (700×Digital Zoom)

Image stabilizer (G15Hi/G20Hi)

From wide-angle to 22×

telephoto — with

unparalleled optical quality.

The digital zoom multiplies

this magnification by more

than 22× for even more

dramatic results.

Images are stabilized even in

long telephoto shots.

Digital effects

Advanced digital technology

allows you to add special

effects during recording and

playback.

Powerful recording programs

Titles

Six recording programs deal

with everything from simple

point-and-shoot operation to

the most challenging

recording conditions.

You can choose from a

selection of preset titles to

add to your recording.

Colour viewfinder (G20Hi)

Remote control

You don’t have to wait until

playback to see your shots in

colour. Thanks to the high-

resolution LCD viewfinder,

you can see just what you’re

getting on tape, making it

easy to shoot colourful,

well-composed video.

Custom Keys

With the unique Custom

Keys, you can decide which

functions you want at your

fingertips. Assign frequently

used functions to the keys on

the camera body.

CUSTOM KEYS

2

1

WEDDING

Easier than manual operation

and more flexible than

automatic functions, Canon’s

FlexiZone Control is a

completely new way to use a

video camera.

FlexiZone Control

The built-in video light

brightens at the touch of a

switch. Recording in low

light (or no light) has never

been easier.

ON

OFF

Video light (G20Hi)

Fade

Photo Mode (G20Hi)

PHOTO

You can record still pictures

like a photograph for

approximately 7 seconds.

Digitally compensates for picture jitter during

playback resulting in a stable picture.

Time base corrector

A small but powerful battery pack that can be

charged at any time.

Lithium ion power supply

Hi8 is the format that

most video professionals

rely on for high quality

and long recording times.

Hi8 (G15Hi/G20Hi)

6

Quick Overview

E

Finding Your Way Around the G2000/G15Hi/G20Hi

Battery pack

(p. 9–10, 52–53)

MENU button

(p. 23, 24)

Custom key 2 (p. 25)

Custom key 1 (p. 25)

SELECT dial (p. 24)

FOCUS button

(p. 38, 39)

SET button (p. 24)

Audio/Video

Output terminal

(p. 20) Video light (G20Hi)

(p. 48)

BATTERY RELEASE

button (p. 9)

C. (counter) RESET button (p. 18)

(pause) button (p. 17)

FADE button (p. 34)

(stop) button (p. 17)

BLC button (p. 40)

(play) button (p. 17)

D.ZOOM button (p. 15)

(rewind) button (p. 17)

REC SEARCH – and

(record review) button (p. 35)

(fast forward) button (p. 17)

REC SEARCH + button (p. 35)

EJECT button (p. 11)

Microphone

Lens (p. 60)

Remote sensor (p. 28)

Cassette compartment

(p. 11)

Zoom control (p. 15)

Grip belt (p. 50)

7

Quick Overview

E

Start/stop button (p. 13)

STANDBY cover (p. 13)

Viewfinder

focusing

switch (p. 50)

Video light switch (G20Hi)

(p. 48)

PHOTO button (G20Hi)

(p. 43)

DC IN terminal (p. 8)

ZOOM buttons (p. 15)

TAPE RETURN button (p. 18)

COUNTER RESET button (p. 18)

FF button (p. 17)

PLAY button (p. 17)

STOP button (p. 17)

Viewfinder (p. 50, 60)

Strap attachment bar

(p. 51)

Strap attachment bar

(p. 51)

S-video output

terminal (G15Hi/G20Hi)

(p. 19)

Program selector

(p. 13–14, 36–37)

FlexiZone controller

(p. 38)

Backup battery

holder (p. 54)

ON SCREEN button (p. 66)

START/STOP button (p. 13)

PAUSE button (p. 17)

REW button (p. 17)

Tripod socket

(p. 21)

CHARGE indicator (p. 9)

8

Quick Overview

E

Powering Your Camcorder

Connecting the camera to a mains outlet

2

1

3

Before operating your camera, you will need to use the power adapter to:

Provide power from an AC outlet

or

Charge a battery pack

Notes:

• The power adapter converts current from a household power socket (100–240 V AC,

50/60 Hz) to the DC current used by your camera.

• If the adapter is used next to a TV, it may cause noise bars to appear on the TV—

move the adapter away from the TV or the aerial cable.

Use the power adapter to provide your camera with instant power from an AC

outlet.

1. Connect the AC cable to the power adapter.

2. Open the terminal cover from its top and connect the power adapter to

the camera’s DC IN terminal.

3. Connect the power adapter to a mains outlet.

4. Remove the power adapter after use.

• Always turn the camera off before connecting/removing the power source.

• For the power adapter, use only Canon CA-550K (or CA-550). Do not use

other equipment.

CA-550K Compact power adapter

Specifications

Power supply 100–240 V AC, 50/60 Hz

Power consumption 20 W

Rated output 8.4 V, 1.5 A DC

Operating temperature range 0°–40°C (32°–104°F)

Dimensions 105 ×30 ×56 mm (4 1/8×1 1/8×2 1/4in)

Weight 270 g (9 1/2oz)

UK Model: 305 g (10 3/4oz)

Australia Model: 290 g (10 1/4oz)

Weight and dimensions are approximate. Errors and omissions excepted.

Subject to change without notice.

9

Quick Overview

E

Charging and attaching the battery pack

Your battery pack was partially charged before it left the factory. It should have

enough power for you to check that your camera is working properly. However,

you must charge the battery pack fully if you want it to power the camera for

more than a few minutes.

1. Set the Program selector to OFF before you charge the battery pack.

2. Open the terminal cover from its top and connect the power adapter

to the camera’s DC IN terminal.

3. Attach the battery pack to the camera.

• Align the triangle on the battery pack with the line on the camera. Slide the

battery in the direction of the arrow until it clicks into place.

4. Plug the adapter into a mains outlet.

• The charge indicator flashes to show that charging is in progress. Single

flashes mean that the battery pack is less than 50% charged. Double flashes

mean that it is between 50% and 75% charged. Triple flashes mean that it is

more than 75% charged. The indicator glows steadily when the battery pack

is fully charged.

5. When charging is complete, disconnect the power adapter.

6. Detach the battery pack after use.

• Press and hold the BATTERY RELEASE button while you slide the battery

off the camera.

• Always turn the camera off before removing the power source.

Note:

• You can find detailed notes for using the batteries in the “Notes on Using the

Batteries” on p. 52. These notes include charging and recording times and how to

install the backup battery.

3

24

BATTERY

POWER

6

BATTERY RELEASE

10

Quick Overview

E

* Continuous recording time will be reduced by approx. 50% with continued

use of the video light. (G20Hi)

• These times vary — the safest policy is always to have 2 or 3 times as many

battery packs as you think you will need.

Continuous recording time (G20Hi: video light off) *

G2000 G15Hi/G20Hi*

BP-911K (supplied) 2 hrs. 30 min. 2 hrs. 10 min.

BP-915 (optional) 2 hrs. 35 min. 2 hrs. 10 min.

BP-930 (optional) 5 hrs. 10 min. 4 hrs. 20 min.

BP-945 (optional) 7 hrs. 55 min. 6 hrs. 40 min.

Charging time

BP-911K (supplied) 3 hrs.

BP-915 (optional) 4 hrs.

BP-930 (optional) 6 hrs.

BP-945 (optional) 8 hrs. 30 min.

Charging and recording times

11

Quick Overview

E

Loading a Cassette

34

2

EJECT

Use video cassettes marked with an f(or gfor G15Hi/G20Hi).

Loading and unloading

1. Make sure that you have attached or connected a power source.

2. Press the 5 EJECT button and wait for the cassette compartment to

open.

3. Load/unload the cassette.

• Insert the cassette gently with the window facing out.

• Remove the cassette by pulling it straight out.

4. Press the Pmark on the compartment until it clicks, and wait for it

to close.

• Never push down the top of the compartment.

Protecting tapes from accidental erasure

REC

SAVE

REC

SAVE

ERASE

OFF ON

ERASE

OFF ON

To protect your recordings from accidental erasure, slide the red switch on the

cassette so that it covers the hole. (This switch position is usually labeled SAVE

or ERASE OFF.) If you load this cassette and power on the camera, “v” flashes

in the viewfinder.

If you want to record on the cassette again, slide the red switch back so the hole is

open. (This position is usually labeled REC or ERASE ON.)

12

Quick Overview

E

Notes:

• Do not interfere with the compartment while it is opening or closing automatically.

• After loading a cassette, use record search (p. 35) to find the point where you want

to start recording.

• Do not leave the cassette in the camera after use — return it to its case and store it

in a cool, clean, dry place.

• The holes in the back of the cassette are used for transferring information — do not

cover them.

Handling cassettes

• To protect the tape heads, transfer cassettes directly from the tape case to the

camcorder – do not open the tape protect cover or touch the tape itself.

• Do not use cassettes where the tape has been damaged or rejoined – they may

damage the camcorder.

• Do not insert anything into the small holes on the cassette or cover them with

cellophane tape.

• Handle cassettes with care – dropping them or exposing them to external shocks

may cause internal damage.

• Store cassettes in the provided case, rewinding them to the start of the tape first,

and then storing them upright.

To record or play back in the Hi8 format, you need both a Hi8 camcorder and a

Hi8 cassette (you can use either Metal-P or Metal-E Hi8 cassettes).

A Hi8 camcorder can record or play back in either the Hi8 format or standard

8mm format, depending on the tape used.

The superior quality of Hi8 can best be appreciated on a TV which has an S-video

input terminal.

About Hi8 (G15Hi/G20Hi)

13

Quick Overview

E

Basic Recording

2

3,4

1

POWER

Before you start recording

Have you completed the following steps?

• Attach a power source (p. 8).

• Load a cassette (p. 11).

• Adjust the viewfinder and fasten the grip belt (p. 50).

• Remove the lens cap (p. 50).

You may also want to install the backup battery (p. 54) in order to set date and

time display (p. 30).

To record

1. Turn the program selector to the aposition.

• This selects the camera’s Automatic recording program. It allows you to

simply point and shoot without making any manual adjustments.

2. Open the STANDBY cover.

• PAUSE appears in the viewfinder — the camera is now in “record pause

mode.”

3. Press the start/stop button to begin recording.

• REC appears in the viewfinder.

4. Press the start/stop button again to pause recording.

• The camera returns to record pause mode and PAUSE reappears in the

viewfinder.

• You can stop and restart recording as often as you like by pressing the

start/stop button.

• The camera will turn itself off if you leave it in record pause mode for more

than about 5 minutes. To return to record pause mode, close and reopen the

STANDBY cover, or set the program selector to OFF and then back to

camera mode.

Safe cassette operation

When you turn the power off or remove the power source, be sure to set the

camcorder first to record pause, stop or still pause mode.

Turning the power off or removing the power source while the tape is moving

(during recording, play, rewind for example), will make the counter display

appear wrong or may cause tape damage.

14

Quick Overview

EWhen you have finished recording

• Replace the lens cap.

• Unload the cassette.

• Set the program selector to OFF.

• Disconnect the power source.

Notes:

• To check that the camera is recording correctly, be sure to make a test recording

first.

• Before making important recordings, clean the video heads using Canon CC-8

Video Head Cleaning Cassette or a commercially available dry-type head cleaning

cassette.

• For tips on how to make better videos, see page 21.

To see a demonstration of the camera’s main features, before loading the cassette,

go to the DEMONSTRATION option in the camera menu. Select the ON setting

and close the menu. The demonstration also starts automatically if the power has

been on for ten minutes without a cassette loaded into the cassette compartment.

(You can avoid this by turning the DEMONSTRATION to OFF through the

camera menu.) To cancel the demonstration once it has begun: push the menu

button, turn off the power, or load a cassette.

Demonstration

DEMONSTRATION ON

...

(see p. 23)

15

Quick Overview

E

Zooming

Turning the 700×digital zoom on/off

Zoom in

Zoom out

T

W

The camera’s 22×zoom lens allows you to choose the best picture angle for each

scene:

• Turn the zoom control towards W to zoom out to wide-angle.

• Turn it towards T to zoom in to telephoto.

You can also control the speed of zooming:

• Move the control slightly to zoom slowly.

• Turn it farther to zoom more quickly. (The farther you turn the zoom control,

the faster the zoom speed.)

The T and W buttons on the wireless controller adjust the picture angle, but not

the zoom speed.

Turn the digital zoom on/off by pressing the D.ZOOM button, to magnify the

camera’s zoom range by more than 22×.

• In addition, for the G15Hi/G20Hi, you can assign CUSTOM KEY 1 to turn the

digital zoom on/off (see p. 25).

The zoom control continues to work as usual. You can freely zoom in and out

between 1×and 700×magnification — the camera automatically switches

between optical zooming (up to 22×) and digital zooming (22×to 700×).

Note:

• When you enter the digital zoom range in FlexiZone mode, the FlexiZone frame

becomes locked in the centre of the viewfinder.

16

Quick Overview

E

Notes:

• The viewfinder display stays lit for approximately 4 seconds following an

adjustment to the picture angle.

• Overuse of the zoom may make recordings seem too busy. It is generally better to

use it sparingly, or in order to reframe between shots.

• When you want to get as close as possible to your subject, keep the zoom at the

wide-angle position. You can focus on a subject as close as 1 cm (3/8in).

• When you turn the digital zoom on, “700×” appears in the viewfinder.

• Image resolution is lower when the magnification is greater than 22×.

Viewfinder displays

Zoom in

Zoom out

Stationary

T

W

T

W

T

W

T

W

T

W

Optical zoom

Digital zoom 700×

17

Quick Overview

E

Playing Back a Cassette

Special playback

FADE BLC

D.ZOOM REC SEARCH

POWER

Still playback

To view the video as a still picture press the abutton. To resume normal

playback, press it again, or press the ebutton. The camera automatically goes

into stop mode after about five minutes’ playback pause.

Fast forward playback

To play back the recording at about 9 times normal speed, press and hold the 1

button during normal playback.

Rewind playback

For reverse playback at about 7 times normal speed, press and hold the `

button during normal playback.

You can use the viewfinder screen for instant, on-the-spot playback.

To play back your recordings on a TV, see p. 19–20.

To use the wireless controller, see p. 28.

1. Attach a power source and turn the program selector to PLAY.

2. Load the cassette.

3. Press the ebutton to start playback.

• To end playback, press the 3 button.

• To wind the tape forwards, stop playback and press the 1(fast forward)

button.

• To wind the tape backwards, stop playback and press the `(rewind)

button.

• If the playback picture is rough, clean the video heads using a Canon CC-8

Video Head Cleaning Cassette or a commercially available dry-type head

cleaning cassette.

Safe cassette operation

When you turn the power off or remove the power source, be sure to set the

camcorder first to record pause, stop or still pause mode.

Turning the power off or removing the power source while the tape is moving

(during recording, play, rewind for example), will make the counter display

appear wrong or may cause tape damage.

18

Quick Overview

E

Tape return

Use the wireless controller’s TAPE

RETURN button to quickly return to a

scene you want to see again. You can

operate this function from the wireless

controller only.

1. Press the COUNTER RESET button during playback if you come

across a scene you want to watch again later.

• The tape counter is reset to 0:00:00.

2. When you have ended playback, press the TAPE RETURN button.

• The tape rewinds and stops when the counter nears 0:00:00.

• You can cancel tape return by pressing the 3button.

3. Start playback.

Notes:

• When the tape reaches the end during normal playback it rewinds automatically.

• Noise bars appear and the soundtrack cannot be heard during special playback. The

picture may roll and divide, appear black and white and the picture may not be

visible during high-speed search.

• During still playback, the picture flickers, and fast action scenes may appear

blurred.

• The tape counter is reset when a cassette is loaded.

• You cannot use the tape return if the tape counter is already near 0:00:00.

• When you playback a cassette suffered considerable vibration or shaking during

recording, you may find that the playback picture is not stable, depending on the TV

you use.

High-speed search

To play back the recording at about 15 times normal speed, press and hold the

1button during normal fast forward. For reverse playback at about 15 times

normal speed, press and hold the `button during normal rewind.

19

Quick Overview

E

Connecting for Playback on a TV Screen

You can connect the camera to a TV or VCR in order to play back your

recordings. You will need to attach a power source to the camera (see p. 8).

See your TV or VCR instruction manual for further details.

• Use the optional S-150 S-video Cable to connect the S-video terminal. Use the

C-250 AV Cable white plug to connect the audio terminal.

• Set the TV/VIDEO selector on the television to VIDEO.

• If you are connecting the camera to a VCR, set the input selector on the VCR to

LINE.

INPUT

VIDEO

AUDIO

S-VIDEO

S-150 S-video Cable

C-250 AV Cable

If your TV (or VCR) has an S-video input terminal (for G15Hi/G20Hi)

C-250 AV Cable

AUDIO

(R) AUDIO

(L/MONO) VIDEO

PC-A5

SCART

Adapter

• Connect the PC-A5 SCART adapter to the TV or VCR’s SCART terminal.

• Connect the camera to the adapter. Connect the camera by using the C-250 AV

Cable. Connect the white plug to the white audio terminal 7(left). Connect the

yellow plug to the yellow video terminal 0.

• Set the TV/VIDEO selector on the television to VIDEO.

• If you are connecting the camera to a VCR, set the input selector on the VCR to

LINE.

If your TV (or VCR) has a SCART terminal (without S-video)

20

Quick Overview

E

Note:

• If you are going to use the TV as a monitor while you are shooting, remember to

keep the TV volume turned down as long as the camera’s audio terminals are

connected. If the sound from the TV speakers is picked up by the microphone, an

unpleasant high-pitched squeal, called feedback, may be produced.

AUDIO IN

VIDEO IN

C-250 AV Cable

• Connect the camera by using the C-250 AV Cable to connect the AV terminal.

Connect the white plug to the white AUDIO terminal. Connect the yellow plug

to the yellow VIDEO terminal.

• Set the TV/VIDEO selector on the television to VIDEO.

• If you are connecting the camera to a VCR, set the input selector on the VCR to

LINE.

If your TV (or VCR) has audio/video input terminals

Page is loading ...

Canon G20 Hi User manual

This manual is also suitable for

Canon G20 Hi User manual

Related papers

Other documents