SharkBite UAB3088FXSS18LFZ is a water heater connector designed to simplify the installation of water heaters, even in tight spaces. Its flexibility makes it easy to connect water heaters with existing pipes that don’t line up, saving you time and effort. Here are some of the key capabilities and potential use cases for the SharkBite UAB3088FXSS18LFZ:
- Quick and easy installation: The SharkBite water heater connector uses a unique push-to-connect design that allows for quick and easy installation without the need for tools or soldering. Simply insert the pipe into the fitting and push until it clicks into place, creating a secure and leak-proof connection.
SharkBite UAB3088FXSS18LFZ is a water heater connector designed to simplify the installation of water heaters, even in tight spaces. Its flexibility makes it easy to connect water heaters with existing pipes that don’t line up, saving you time and effort. Here are some of the key capabilities and potential use cases for the SharkBite UAB3088FXSS18LFZ:
- Quick and easy installation: The SharkBite water heater connector uses a unique push-to-connect design that allows for quick and easy installation without the need for tools or soldering. Simply insert the pipe into the fitting and push until it clicks into place, creating a secure and leak-proof connection.
US 1 877 700 4242 | sales@sharkbite.com | sharkbite.com
Canada 1 888 820 0120 | canadasales@rwc.com
Shark Bite
Water Heater Connector
Flexible water heater connectors allow you to work in tight spaces and
easily connect water heaters with existing pipes that don’t line up.
Data Sheet
Expansion Fittings
Features and Benets
• Fastest way to connect water heater to hot or cold water lines
• Flexiblity makes installation easier when pipes do not line up
• Compatible with PEX-A
• Can be used as an alternative to hard piping.
Applications
• Potable water and radiant heating
SBEFWAHC0321
Page 1 of 2
Specications
SharkBite expansion fittings shall be installed on SharkBite PEX-A
complying with ASTM F876 or CSA B137.5. The fittings shall be
made of Engineered Polymer or DZR lead-free Brass and be com-
pliant with ASTM F1960. The fittings shall be used in a potable
water or radiant heating/cooling system not to exceed 80 psi @
200°F, 100 psi @ 180°F, or 160 psi @ 73.4°F.
# UAB3088FXSS18LF
US 1 877 700 4242 | sal[email protected]om | sharkbite.com
Canada 1 888 820 0120 | canadasales@rwc.com
SBEFWAHC0321
Page 2 of 2
Technical Data
Material
Specication Data
33°F to 73°F at 160 psi
180°F at 100 psi
200°F at 80 psi
Minimum working temperature
Maximum working temperature
Hose
Fitting
Washer
SST
DZR Lead Free Brass
1
EPDM
1
2
3
Description
Dimensions
APart # B
PEX-A FLEX CNCTR 3/4”X3/4”FIPX18” SS LF UAB3088FXSS18LF
20.12
1.02
All measurements are displayed in inches
#UAB3088FXSS18LF
C
1.17
D
F1960 3/4PEX
1
Lead Free for all models, surfaces that are in contact with consumable water contain less
than 0.25% lead by weight
A
B
C
D
Fitting Size Nominal Pipe Size
Insertion Depth
Insertion Depth(in)
1/2 in.
3/4 in.
1 in.
1/2 in.
3/4 in.
1 in.
0.72
0.97
1.19
Using an approved manual or cordless expansion tool, insert the tool
into the PEX pipe and expand the pipe.
*Note that each pipe size requires the specific expander head, so ensure
it is the correct size prior to beginning. The number of expansions will be
dictated by the tubing size.
Once the tubing is expanded, insert the fitting until it hits the shoulder
and allow the PEX to contract around the fitting until secure. After several
seconds the tubing will secure around the fitting, and your connection is
made and ready for use.
How to install SharkBite Expansion Fittings products.
Installation Requirements
Use pipe cutters to make a square cut of the pipe to length. A rough or
uneven cut can result in a weakened joint.
Slide your expansion ring over the PEX tubing until it overhangs the end of
the tubing by no more than 1/8” or until the stop on the ring (if present)
touches the tubing.
1
2
3
4
Compatible with PEX-A pipe
Pipe Type
1/2 in. fittings and pipe 2-1/2 in. space
3/4 in. fittings and pipe 3-1/2 in. space
1 in. fittings and pipe 4-1/2 in. space
Minimum Distance Between Fittings
Codes and Standards
ASME A112.18.6/CSA B125.6
NSF/ANSI 14
NSF/ANSI/CAN 61
NSF/ANSI/CAN 372
It is important to make sure the expander head rotates after each
expansion to prevent ridges on the inside of the tubing.
• 6 expansions for 1/2 in.
• 8 expansions for 3/4 in.
• 5 expansions for 1 in.
-
1
-
2
SharkBite UAB3088FXSS18LFZ User manual
- Type
- User manual
- This manual is also suitable for
SharkBite UAB3088FXSS18LFZ is a water heater connector designed to simplify the installation of water heaters, even in tight spaces. Its flexibility makes it easy to connect water heaters with existing pipes that don’t line up, saving you time and effort. Here are some of the key capabilities and potential use cases for the SharkBite UAB3088FXSS18LFZ:
- Quick and easy installation: The SharkBite water heater connector uses a unique push-to-connect design that allows for quick and easy installation without the need for tools or soldering. Simply insert the pipe into the fitting and push until it clicks into place, creating a secure and leak-proof connection.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
SharkBite UAB23058LFA User manual
-
-
-
-
-
Cash Acme 25930-0045 Installation guide
-
-
-
-
Other documents
-
Apollo EPXTOOL Operating instructions
-
-
Watts 3/4 LFFBVD-PEX-F1960 Installation guide
-
Watts ASTM F1960 Expansion Fittings Installation guide
-
Rehau F1960 Product Instructions
-
Milwaukee 2633-22 User guide
-
-
BrassCraft WB27-18 User guide
-
Watts R-flex User guide
-
Uponor Wirsbo ProPEX Q6301000 Installation guide
