English
1 I iConnects MicroVisor
Before using your iConnects MicroVisor for the first time, you must charge it
continuously for approximately 3 hours, until the indicator change to green.
Please refer to the “Charging the iConnects MicroVisor” section of this manual.
Introduction
The iConnects MicroVisor is a wireless car kit based on Bluetooth® technology.
It complies with Bluetooth® 2.0 protocol, supporting Headset and Handsfree profile.
The iConnects MicroVisor has 3 buttons:
“TALK” button (main button)
“VOL+” button
“VOL-“ button Powerful speaker
Rotary microphone
arm
VOL- button
VOL+ button
Indicator light
Charging Socket
TALK button
English
iConnects MicroVisor I 2
Using the J$POOFDUT.JDSP7JTPS in dierent
environment
Mounting on the sun visor as a car kit
When using your iConnects MicroVisor in your car, simply mount the unit onto
the visor with the clip as shown in Diagram 1.
Mic 1
Mic 2
Diagram 1
For best voice reception, please adjust the rotary microphone arm around 45 degree, or
other position suits you most.
English
iConnects MicroVisor I 4
You can also connect the charging cable to a USB socket.
Diagram 3
While charging, the indicator light on the iConnects MicroVisor should be orange.
The green indicator light will turn on when the unit is fully charged. Subsequent charges
should take approximately 3 hours.
When the indicator light on your iConnects MicroVisor ashes in red at regular
intervals (or the voice alert is activated), the unit needs to be recharged.
English
5 I iConnects MicroVisor
Pairing the J$POOFDUT.JDSP7JTPS
Before using the iConnects MicroVisor, you must pair it with your Bluetooth®
mobile phone. Pairing is the process of linking 2 Bluetooth® devices, so that they can
communicate.
To initiate pairing:
1. Place the iConnects MicroVisor and your mobile phone within 0.3 meter (1
foot) from each other.
2. Switch on your phone and select its Bluetooth® discover mode (refer to the Bluetooth®
mobile phone user manual).
3. When the iConnects MicroVisor is switched on, press and hold both the TALK
button and the VOL+ button for about 5 seconds until the indicator light ashes red and
blue alternately. And a sound can be heard in the speaker.
4. Once the mobile phone detects the car kit, a message
will be displayed. Follow the phone instructions to accept the pairing. The PIN code (or
passkey) is 0000, then press “yes” or “ok”.
If pairing was successful, the indicator light will switch to blue.
If you haven’t started the discovery mode within 5 minutes, it will stop. In this case, you
must start the pairing again as step 3 above.
English
iConnects MicroVisor I 6
Switching the J$POOFDUT.JDSP7JTPS ON and OFF
Switching the J$POOFDUT.JDSP7JTPSON
Switch on the iConnects MicroVisor by lifting up
the microphone arm as shown in Diagram 4. You will hear
a beep (2 tones) in the speaker (and continuous
connecting beeps until it is connected to the handset).
During about 5 seconds, you can see the blue LED blinking
until the iConnects MicroVisor is switched on.
Once the iConnects MicroVisor is switched on,
you can see the blue LED keeps lighting.
Switch o the iConnects MicroVisor as shown
in Diagram 5.
Switching the J$POOFDUT.JDSP7JTPS OFF
Diagram 4
Diagram 5
English
7 I iConnects MicroVisor
Making a call
Make sure the headset is paired to your phone and in range, dial the number on the phone
keypad and press call.
*For mobile phone with voice recognition
· Make sure the voice recognition function on your mobile is activated and your voice tags
have been recorded with the phone. To enter these, please refer to your phone’s manual.
· When there is no incoming or active call, press once on the TALK button
· Wait for the audio signal sent by the mobile phone (generally a short tone).
· Speak the name of person you wish to call.
*This function may not be available on some phones, please refer to your phone’s manual.
Answering a call
When your J$POOFDUT.JDSP7JTPS is OFF
Switch on your J$POOFDUT.JDSP7JTPS. After about 3 seconds, It will automatically
transfer the call from the phone to the car kit For some phones, you may need to press
“Connect” on the phone.
When your J$POOFDUT.JDSP7JTPS is ON
Press once on the TALK button to take the call.
English
iConnects MicroVisor I 8
Ending a call
Press once on the TALK button to end an active call.
Adjusting the volume
To increase the volume during an active call, press the “VOL+” button on the iConnects
MicroVisor
To decrease the volume during an active call, press the “VOL-“ button on the iConnects
MicroVisor
Muting the microphone
To mute the microphone during an active call
During an active call, press and hold the VOL+ or VOL- button for approximately 2 seconds. A
periodic tone can be heard in the speaker when the microphone is muted. You can still adjust
the speaker volume by pressing shortly on the VOL+ or Vol- button.
To end the mute function
When the microphone is muted, press and hold the VOL+ or VOL- button for approximately 2
seconds. The periodic tone will end.
English
9 I iConnects MicroVisor
Transferring a call from the J$POOFDUT.JDSP7JTPS
to the mobile phone
With a phone in Headset Profile
During an active call, to transfer it to the phone, simply turn o your iConnects MicroVisor
With a phone in Hands-Free Profile
During an active call, to transfer it to the phone, double click on the TALK button.
Transferring a call from the mobile phone to your
J$POOFDUT.JDSP7JTPS
With a phone in Headset Profile
Switch on your iConnects MicroVisor
With a phone in Hands-Free Profile
During an active call on the mobile phone, double click on the TALK button. It will take few
seconds to re-establish the connection between the mobile phone and the car kit. (Some
phones may need fulfil this function by pressing once to reconnect the mobile phone to the
iConnects MicroVisor)
English
iConnects MicroVisor I 10
Call waiting
When you hear a call waiting alert while you are on a call, press the TALK button on the
iConnects MicroVisor approximately 2 seconds to accept the second call and
place the current call on hold.
To switch between an active call and a held call, press the TALK button on the iConnects
MicroVisor approximately 2 seconds.
To end the active call and take the held call, press the TALK button once on the iConnects
MicroVisor.
Rejecting a call
Press the TALK button on your car kit for approx. 3 seconds to reject the call.
Redial the last number
With a phone in Headset Profile
This function is not available.
With a phone in Hands-Free Profile
When there is no incoming or active call, press the TALK button on your carkit for approx. 2
seconds.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Hyundai Tucson 2015 Quick Reference Manual
-
-
-
-
-
-
-
-
Hyundai Elantra Quick Reference Manual
-