2. Shop fox
  3. W1669

Shop fox W1669, 1/2 HP 34 in. Bench-Top Radial Drill Press W1669 Owner's manual

  • Hello! I've reviewed the datasheet for the Shop Fox W1669 Drill Press. This document details the specifications of a 1/2 HP 34" Bench-Top Radial Drill Press, including it's radial design, 5 speeds, and a range of adjustable components. I'm ready to answer your questions about its features, capabilities, or any other details you might be interested in.
  • What is the power requirement for the drill press?
    What is the drilling capacity in mild steel?
    What is the size of the drill chuck?
    What is the spindle taper type?
Model W1669 Machine Specifications, Page 1 of 3
MODEL W1669
1/2 HP 34" BENCHTOP RADIAL DRILL PRESS
Product Dimensions
Weight........................................................................................................... 91 lbs.
Width (side‐to‐side) x Depth (front‐to‐back) x Height.............................. 12 x 33‐1/2 x 31‐1/2 in.
Footprint (Length x Width)..................................................................... 13‐1/2 x 8‐1/2 in.
Shipping Dimensions
Type.................................................................................................... Cardboard Box
Content........................................................................................................ Machine
Weight........................................................................................................... 98 lbs.
Length x Width x Height........................................................................... 36 x 18 x 13 in.
Electrical
Power Requirement.................................................................... 120V, Single‐Phase, 60 Hz
Full‐Load Current Rating........................................................................................ 4.7A
Minimum Circuit Size............................................................................................. 15A
Connection Type......................................................................................... Cord & Plug
Power Cord Included.............................................................................................. Yes
Power Cord Length............................................................................................... 7 ft.
Power Cord Gauge............................................................................................ 18 AWG
Plug Included....................................................................................................... Yes
Included Plug Type............................................................................................... 5‐15
Switch Type............................................................. Toggle Safety Switch w/Removable Key
Motors
Main
Horsepower.............................................................................................. 1/2 HP
Phase.............................................................................................. Single‐Phase
Amps......................................................................................................... 4.7A
Speed.................................................................................................. 1725 RPM
Type......................................................................... TEFC Capacitor‐Start Induction
Power Transfer ................................................................................... V‐Belt Drive
Bearings............................................................... Shielded & Permanently Lubricated
Model W1669 Machine Specifications, Page 2 of 3
Main Specifications
Operation Information
Type....................................................................................................... Radial
Swing....................................................................................................... 34 in.
Spindle Taper............................................................................................. JT#33
Spindle Travel........................................................................................ 3‐1/4 in.
Max. Distance From Spindle to Column..................................................... 5‐1/2 ‐ 17 in.
Max. Distance From Spindle to Table............................................................ 11‐1/2 in.
Number of Spindle Speeds................................................................................... 5
Range of Spindle Speeds..................................................................... 550 ‐ 3000 RPM
Max. Head Tilt (Left/Right).................................................................... 90 / 45 deg.
Max. Head Swivel..................................................................................... 360 deg.
Drilling Capacity (Mild Steel)............................................................... 1/2 in. in Steel
Drill Chuck Type.............................................................................. JT33 Key Chuck
Drill Chuck Size................................................................................. 1/16 ‐ 5/8 in.
Spindle Information
Distance From Spindle to Base.................................................................... 17‐1/2 in.
Quill Diameter........................................................................................ 1.575 in.
Table Information
Max. Table Tilt (Left/Right).......................................................................... 90 deg.
Table Swing............................................................................................ 360 deg.
Table Swivel Around Center........................................................................ 360 deg.
Table Swivel Around Column....................................................................... 360 deg.
Max. Movement of Work Table..................................................................... 9‐1/2 in.
Table Length............................................................................ (Diameter) 9‐3/4 in.
Table Width............................................................................. (Diameter) 9‐3/4 in.
Table Thickness............................................................................................ 1 in.
Vertical Table Travel.............................................................. Crank Handle Operation
Number of T‐Slots............................................................................................. 6
T‐Slot Size............................................................................................... 1/2 in.
T‐Slot Centers......................................................................................... 2‐3/4 in.
Floor‐To‐Table Height.................................................................... 7‐3/4 ‐ 17‐1/4 in.
Construction
Table............................................................................. Precision‐Ground Cast Iron
Column..................................................................................................... Steel
Spindle Housing....................................................................................... Cast Iron
Head.................................................................................................... Cast Iron
Base.................................................................................................... Cast Iron
Paint Type/Finish...................................................................................... Enamel
Other Related Information
Base Length.......................................................................................... 13‐1/2 in.
Base Width............................................................................................ 8‐1/2 in.
Column Diameter..................................................................................... 2.360 in.
Depth Stop Type......................................................... Threaded Rod with Positive Stop
Has Work Light............................................................................................... No
Model W1669 Machine Specifications, Page 3 of 3
Other
Country of Origin ............................................................................................... China
Warranty ....................................................................................................... 2 Years
Approximate Assembly & Setup Time ................................................................. 30 Minutes
Serial Number Location .......................................................................... ID Label on Head
ISO 9001 Factory .................................................................................................. Yes
Certified by a Nationally Recognized Testing Laboratory (NRTL) ......................................... Yes
Features
Threaded Depth Stop
Crank Handle Operated Rack and Pinion Vertical Table Movement
Table Has Lock Levers
Table and Base are Cast Iron
Radial Design Allows Angle Drilling
5 Speeds
1/2HP Motor
Cushioned Grip Quill Handles
1/16" ‐ 5/8" Drill Chuck
/