Orthofab Tango User manual

Type
User manual
USER MANUAL
July 2008
inc All rights reserved
2
Please give this manual to the owner of the
wheelchair.
Please read this manual in it entirety before using your
wheelchair for the first time. Read
this manual until it becomes familiar and pay close attention
to the warnings.
If you have any questions about non-covered subjects in this
manual, please consult a technician in an authorized service
center or contact our customer service at: 1-(418)-847-5225
Center:
Address:
Phone:
The adjustments of your wheelchair must be made
by a health care professional. Inadequate adjustments can
cause wounds and/or damage to the user, the caregiver, the
wheelchair or the environment.
Do not install unauthorized accessories. Always consult a
health care professional for any modifications to your
wheelchair.
inc All rights reserved
3
is proud to count you among its customers and thanks you for having
chosen one of its products.
All the products manufactured by respect or exceed the highest standards
of quality and safety currently in force in the industry. personnel is guided
by the desire to satisfy customers expectations. This is why does not
hesitate to offer a most complete warranty, applying to the whole wheelchair elements
and components. However, the warranty does not apply to parts and components
damaged by abuse, carelessness, accident and normal use or installed and modified by
an unauthorized person.
This operating instructions manual has been written to enable you to use your
wheelchair safely. You will find in this document, information
relating to safety, operating instructions and adjustments.
In order to optimize the performance of your and to extend is
lifespan, it is essential to have it check regularly by a technician from an authorized
service center.
refuse any responsibility for physical injuries or damages resulting from an
improper use of its products, from a lack of precaution in their use or from a modification
made without it written assent.
TABLE OF CONTENTS
inc All rights reserved
4
1 SAFETY REQUIREMENTS................................................................................. 6
1.1 SAFETY REQUIREMENTS................................................................................. 6
1.1.1
BEFORE TAKING THE ROAD ........................................................................................................6
1.1.2
MOVING WITH THE WHEELCHAIR...............................................................................................7
1.1.3
TO CARRY OUT TRANSFERT .......................................................................................................7
1.1.4
VARIOUS HANDLING OPERATIONS.............................................................................................8
1.1.5
CLEANING AND MAINTENANCE OF COMPONENTS..................................................................9
1.2 WHAT ABOUT THE ELECTROMAGNETIC ENERGY ....................................... 9
1.2.1
CAUTION.......................................................................................................................................10
1.2.2
USING TRANSMITTERS AND RECEIVERS................................................................................10
2 RECOMMENDED USE...................................................................................... 11
3 SPECIFICATIONS............................................................................................. 12
4 SETUP INSTRUCTIONS ................................................................................... 13
4.1 FOOTREST........................................................................................................ 13
4.1.1
LEGREST LENGHT ADJUSTMENT..............................................................................................13
4.1.2
CHANGING FOOTPLATE ANGLE................................................................................................14
4.1.3
CHANGING POSITION (DEPTH) OF THE COMPOSITE FOOTPLATE ......................................14
4.1.4
CHANGING CALF PAD HEIGHT...................................................................................................15
4.1.5
CHANGING CALF PAD POSITIONS.............................................................................................15
4.2 ADJUSTABLE «U» SHAPE ARMREST HEIGHT............................................. 16
4.2.1
TO PROHIBIT REMOVING THE ARMREST.................................................................................16
4.2.2
TO PROHIBIT ADJUSTMENT IN HEIGHT....................................................................................16
4.3 TELESCOPIC ARMREST «T» SHAPE............................................................. 17
4.3.1
TO LIMIT THE TELESCOPIC ARMREST HEIGHT ADJUSTMENT.............................................17
4.4 DYNAMIC BACKREST...................................................................................... 18
4.4.1
DYNAMIC BACKREST INSTALLATION .......................................................................................18
4.4.2
DYNAMIC BACKREST ADJUSTMENT.........................................................................................20
4.5 ADJUSTABLE BACKREST .............................................................................. 21
4.5.1
CHANGING THE BACKREST ANGLE..........................................................................................21
4.5.2
CHANGING THE BACKREST HEIGHT ........................................................................................23
4.5.3
STABILIZER BAR WITH HEADREST SUPPORT.........................................................................24
4.5.4
STABILIZER BAR WITH HEADREST SUPPORT AND ADJUSTABLE ANGLE PUSH HANDLE25
4.5.5
ADJUSTABLE ANGLE PUSH HANDLE........................................................................................26
4.6 SEATING ADJUSTMENTS ............................................................................... 28
4.6.1
CHANGING SEAT DEPTH............................................................................................................28
4.6.2
CHANGING SEAT HEIGHT...........................................................................................................29
4.6.3
MAXIMUM TILT ANGLE ADJUSTMENT.......................................................................................32
4.7 SEAT WITH MOTORIZED TILT MECHANISM ................................................. 33
4.7.1
DISMANTLING BEFORE INSTALLATION....................................................................................33
4.7.2
UPPER ANCHOR INSTALLATION................................................................................................33
4.7.3
LOWER ANCHOR INSTALLATION...............................................................................................34
4.7.4
BATTERIES COMPARTMENT INSTALLATION...........................................................................35
4.7.5
CONTROL BOX AND ITS SUPPORT INSTALLATION ................................................................37
4.7.6
CABLE WINDER INSTALLATION.................................................................................................38
4.7.7
TILT MECHANISM POSITIONING SYSTEM ADJUSTMENT.......................................................39
4.8 FRONT WHEELS .............................................................................................. 40
4.8.1
TO CHANGE THE FRONT PART OF THE FRAME OR THE FRONT WHEEL POSITIONS.......40
4.8.2
CHANGING THE TYPES OF WHEELS AND HEIGHT (FRONT AND REAR) .............................41
4.9 REAR WHEELS (standard propulsion)........................................................... 42
MID-WHEELS (central propulsion)............................................................................ 42
4.9.1
CHANGING REAR WHEEL MODEL.............................................................................................42
4.9.2
CENTER OF GRAVITY ADJUSTEMENT......................................................................................44
4.9.3
CHANGING MID-WHEEL AXLE POSITION..................................................................................47
4.9.4
CHANGING THE OVERALL WIDTH.............................................................................................48
TABLE OF CONTENTS
inc All rights reserved
5
4.9.5
TO INSTALL 12 INCHES REAR WHEELS....................................................................................50
4.10 PARKING BRAKES .......................................................................................... 52
4.10.1
TO ADJUST THE POSITION OF THE PARKING BRAKE (Pushing or pulling brake type)..........52
4.10.2
TO CHANGE THE BRAKE LEVERS.............................................................................................56
4.10.3
TO CHANGE THE ANGLE OF THE BRAKE LEVER (pushing brake type only)..........................58
4.11 ANTI-TIPPERS.................................................................................................. 59
4.11.1
HEIGHT ADJUSTMENT ................................................................................................................59
4.12 TILT MECHANISM ............................................................................................ 61
4.12.1
TO ADJUST THE FORCE REQUIRED TO TILT...........................................................................61
5 OPERATING INSTRUCTIONS.......................................................................... 62
5.1 «U» SHAPE REMOVABLE ARMREST............................................................. 62
5.1.1
TO SWINGAWAY ..........................................................................................................................62
5.1.2
TO REMOVE AND/OR INSTALL...................................................................................................63
5.1.3
HEIGHT ADJUSTMENT ................................................................................................................63
5.2 ADJUSTABLE « T » SHAPE ARMREST.......................................................... 64
5.3 FOOTREST / LEGREST.................................................................................... 65
5.3.1
SWINGAWAY.................................................................................................................................65
5.3.2
TO REMOVE AND/OR INSTALL...................................................................................................67
5.3.3
TO RAISE OR LOWER THE LEGRESTS.....................................................................................67
5.3.4
RETRACTABLE FULL LENGTH LEGREST..................................................................................68
5.4 BACKREST....................................................................................................... 71
5.4.1
TO FOLD THE BACKREST...........................................................................................................71
5.4.2
RECLINING BACKREST...............................................................................................................72
5.5 SEAT TILT MECHANISM.................................................................................. 73
5.5.1
BACKWARD TIPPING...................................................................................................................73
5.5.2
FORWARD TIPPING.....................................................................................................................73
5.5.3
TILT WITH THE MOTORIZED TILT MECHANISM.......................................................................74
5.5.4
RECHARGING BATTERIES..........................................................................................................75
5.6 REAR WHEELS................................................................................................. 77
5.6.1
TO REMOVE AND/OR INSTALL...................................................................................................77
5.6.2
PNEUMATIC TIRE PRESSURE....................................................................................................77
5.7 PARKING BRAKES .......................................................................................... 78
5.7.1
TO APPLY AND DISENGAGE THE PARKING BRAKE the PUSHING type ................................78
5.7.2
RETRACTABLE HANDLES...........................................................................................................78
5.7.3
APPLY – DISENGAGE THE HILL HOLDER.................................................................................79
5.7.4
12 INCHES REAR WHEELS BRAKE............................................................................................80
5.8 ANTI-TIPPERS.................................................................................................. 81
5.8.1
TO REMOVE..................................................................................................................................81
5.8.2
TO SWINGAWAY ..........................................................................................................................81
5.8.3
TO REPLACE.................................................................................................................................82
5.9 SEAT BELT....................................................................................................... 83
5.10 TRANSPORTATION.......................................................................................... 84
5.10.1
ANCHOR POINTS POSITION.......................................................................................................84
5.10.2
ADVICE FOR TRANSPORTATION...............................................................................................85
6 MAINTENANCE................................................................................................. 86
7 BREAKDOWN SERVICE GUIDE...................................................................... 88
8 WARRANTY...................................................................................................... 89
9 AUTHORIZED SERVICE CENTRES................................................................. 91
1. SAFETY REQUIREMENTS
inc All rights reserved
6
The adjustments of your wheelchair must be made by
a health care professional or a technician in an authorized
service center.
1 SAFETY REQUIREMENTS
1.1 SAFETY REQUIREMENTS
(Applies to all wheelchairs)
1.1.1 BEFORE TAKING THE ROAD
Always put the key switch OFF before getting on or off your vehicle.
Make sure that the batteries are sufficiently charged (see battery status
indicator).
Make sure that the anti-tippers are installed.
Make sure that brakes immobilize your wheelchair completely.
Make sure that the tire pressure is appropriate.
Make sure that nothing interferes with wheels (scarf, umbrella, etc…).
Make sure that your seating position is stable.
Position the backrest in the raised position.
Make sure the 45° tilt mechanism is in driving position (seat horizontal with the
ground).
Fasten your seat belt correctly and without too much slack.
Make sure that swing away legrests are locked in position and that your feet are
stable on them.
Push down the elevator legrests.
Make sure that the swing away or removable armrests are locked in their
positions.
Make sure that the position of the joystick box enable you to carry out all your
movements comfortably and easily.
Make sure that the joystick rubber cover is in good condition, if not, try to have it
fixed as soon as possible.
Make sure that your personal effects do not block in anyway the wheelchair
functions.
Do not install or transport heavy objects on the backrest of your wheelchair
(backpack, bags, grocery, etc).
1. SAFETY REQUIREMENTS
inc All rights reserved
7
1.1.2 MOVING WITH THE WHEELCHAIR
Avoid any shock to the joystick box or the joystick itself.
Avoid slippery surfaces (snow, ice, etc).
Do not change direction abruptly at high speed.
Do not use your wheelchair on expressways or streets with intense car circulation.
Do not transport passengers.
Do not use your wheelchair under extreme climatic conditions (storm, rain, etc).
If you drive outside at night, ensure that you will be seen by others.
Do not approach a slope in a diagonal trajectory, always approach the slope in a
straight line, perpendicularly to the slope.
Do not go down in a slope in reverse.
Always actuate the lever gently when you start moving in a slope in order to avoid
tipping the wheelchair.
Do not make a half-turn in a slope.
Reduce your speed in restricted or encumbered areas.
Reduce your speed in a crowd and use your horn to announce your presence.
In front of an obstacle you must stop and cross it perpendicularly and gradually.
Avoid thresholds of more than 1 ½ in (38 mm), they can endanger your stability.
Use the elevators to move you from one level to another.
Do not approach a slope surface exceeding 10° (17% slope).
Always fasten your seat belt.
Keep legs on the legrest while driving.
1.1.3 TO CARRY OUT TRANSFERT
Always put the on/off switch of the joystick box on the OFF position before carrying
out a transfer.
Never lean forward or backward to reach an object.
Always place yourself sideway and the nearest you can to the object to reach.
Use the transfer supports on the armrests to raise yourself, after you made sure that
they are correctly in position.
If your backrest is inclined, do not sit down on the backrest, you could damage the
backrest and tip the wheelchair.
Do not raise yourself upright on the footplates, you could damage and/or tip the
wheelchair.
Do not sit on the armrests. The wheelchair could tip over.
1. SAFETY REQUIREMENTS
inc All rights reserved
8
1.1.4 VARIOUS HANDLING OPERATIONS
Never try to recharge the batteries in your bedroom while you
sleep. During recharge, batteries can produce a harmful gas
who can cause you health problem.
Do not immerse your wheelchair, it could cause a dangerous electrical problem.
Do not store or leave your wheelchair without someone taking care of it.
Do not leave your wheelchair under the rain.
Do not store your wheelchair in a wet or very cold place, this could cause a
dangerous problem on your motorized wheelchair.
does not limit nor exclude that the user remains seated in his
wheelchair when using a road vehicle adapted for transportation (paratransit),
provided the driver and the owner of the aforesaid road vehicle respects, on this
subject, all legislative requirements, rules, laws, protocols, directives, norms,
standards, instructions and recommendations pertaining to such use by
competent authorities.
Do not travel on tilted surfaces when the wheelchair is in free wheel. If you have
to do it, the caregiver must always be oriented in the direction of the bottom of
the slope.
Do not raise the wheelchair by its detachable components (armrest, seat, etc).
Do not use your battery charger in a hermetic place (backpack, drawer, etc.).
Always put the on/off switch of the charger on the OFF position before
disconnecting the charging connector on the wheelchair.
Never try to modify the connector (110 V AC) of the battery charger.
Never try to modify the battery charger connector (24 V DC) which connect to the
wheelchair.
Never try to recharge the batteries in your bedroom while you sleep.
Never connect an electric component other than those manufactured by
.
Never modify the electric circuit of the wheelchair.
Always protect the joystick box when you have to carry the wheelchair.
Always immediately replace any damaged electric wires.
Always carry out regularly maintenance of your motorized wheelchair as
recommended by .
1. SAFETY REQUIREMENTS
inc All rights reserved
9
1.1.5 CLEANING AND MAINTENANCE OF COMPONENTS
Clean as soon as possible your joystick box once it been soiled.
Use a soft rag and a diluted soft soap.
Do not use detergent based on alcohol or thinner.
Regularly carry out maintenance of your wheelchair as recommended by
.
1.2 WHAT ABOUT THE ELECTROMAGNETIC ENERGY
All electronic instruments which transmit remote informations are generally
apparatus which emit in the environment some radio waves. These radio waves
are called " electromagnetic energy ".
The functionality of an electronic instrument can be deteriorated by this
electromagnetic energy field. It is what we call " an electromagnetic
interference". Stronger the intensity of energy is, greater the risk of bad
functional problem of the apparatus increase. This energy is measured in volt
per meter (V/m).
All motorized wheelchair are suitable to be affected by these interferences.
However, current technology makes it possible to immunize them against these
risks. It is what is called their electromagnetic level of immunity to the
interference, measured also in volt per meter (V/m).
20 V/m is a level of immunity which offer a good protection against the
electromagnetic interferences. The electronic parts of the R-NET electronic from
do meet standard directive IEC 1000-4-3.
To avoid electromagnetic interferences, it is important to read
and respect the following warning section, before to use your
wheelchair for the first time.
1. SAFETY REQUIREMENTS
inc All rights reserved
10
1.2.1 CAUTION
Waves emitted by :
Radio and television stations;
Amateur radio;
Radio transmitters and receivers;
Cellular phones;
Computers laptop.
CAN AFFECT THE CORRECT FUNCTIONALITY OF MOTORIZED WHEELCHAIR.
1.2.2 USING TRANSMITTERS AND RECEIVERS
Avoid proximity of these sources of electromagnetic emissions.
Always put the joystick box in the OFF POSITION before using a cellular phone
or a CB apparatus.
The addition of electric accessories and/or electric modifications made to the
wheelchair will modify its level of immunity to the electromagnetic emissions.
Always put the key in the OFF POSITION as soon as it safe to do it and that
appears an erratic operation with the wheelchair.
Please forward any incident of this kind to .
2. RECOMMENDED USE
inc All rights reserved
11
2 RECOMMENDED USE
The
manual tilt wheelchair offers all the mechanical characteristics and
necessary functions for easy installation and adjustment of seating products; its
structural concept allows assembly of specialized posture components.
The harmonious integration of these characteristics allows you to increase the
propulsion function of your client. With the
it is now possible to avoid the usual
compromise between seating products and propulsion of the wheelchair.
3 SPECIFICATIONS
3 SPECIFICATIONS
Dimensions
Weight: 38 lbs* Note: The weight does not include rear wheels and the footrests.
Overall length: with a 20 " wheel = 27 " to 33 "
with a 22 " wheel = 28" to 34" Note: The overall length is measured without the footrest,
with a 24 " wheel = 29" to 35" with a depth of 16 inches and includes footrest hanger brackets.
Overall width : Width + 8 ¼" to + 9 3/4"
Capacity : 250 lbs
Frame Front wheels
Steel structure Polyurethane 6-7-8 inches
Straight frame Pneumatic 6-8 inches
Widened frame Foam filled insert 6-8 inches
Epoxy Paint
Rigid frame
Rear wheels
Center of gravity adjustment (7 positions, by 1 inch step)
Semi-pneumatic de 20-22-24 inches
Seating (lowered)
Polyurethane 20-22-24 inches
Tilt from -5° to 45°, 3 position for balance adjustment, +/- 25% Pneumatic 20-22-24 inches
Motorized tilt mechanism 0° to 35° Foam filled insert 12-20-22-24 inches
Width: 14-15-16-17-18-19-20 inches Spoke wheels 20-22-24 inches
Depth: 16-17-18-19 inches or 19-20-21-22 inches Mag wheels 20-22-24 inches
Rigid seat or rigid elastic seat
Profiled or straight cushion
Adjustable height from 14-15-16-17-18 or 19 inches
Handrims
Aluminum 20-22-24 inches
Backrest (Dynamic)
Plastic coated 20-22-24 inches
Adjustable angle and foldable 90°-95°-100°-105°-110°-115°-120°
Foam coated 20-22-24 inches
Reclining with pneumatic actuator 90° to 160°
Height adjustment from 16 to 25 inches
Reclining height 16 to 25 in
Wheel locks
Strap backrest Standard wheel lock (pushing or pulling)
Adjustable tension strap backrest Adjustable angle handles
Stabilizer bar with headrest support
Wheel lock extension
Adjustable angle push handle
Hill holder
Headrest
Inaccessible to the user (with foot)
Articulated 3 axis articulated
Armrest Seat to floor height chart
Swingaway
Adjustable height from 10 to 14 inches
option: 8 to 12 inches or 6 to 8 inches
Front
wheels Rear
wheels
Minimum front and rear
seat to floor height
3 positions, 1” inch step
Armrest upholstery length 10 or 14 inches 6 inches 20 inches 14 inches
Width of armrest upholstery 2 inches 6 inches 12 inches 15 inches
Footrest
7 inches 12 inches 15 inches
Length adjustment from: 14 to 19 inches
Length modification: less than 14 inches or more than 19 inches
7 inches
8 inches 22 inches
24 inches 15 inches
16 inches
Swing away – removable
Angle 60° / 70° parallel or tapered
90° angle parallel only
Elevating
Articulated
Assisted elevation system
Footplates
Foldable
Composite
Aluminum narrow or large
Aluminum narrow or large, angle adjustable
Aluminum full width
Heel loops
Toe loops
Front roller bumper
L.U.+ 8¼ "
33
"
4 SETUP INSTRUCTIONS
inc All rights reserved
13
4 SETUP INSTRUCTIONS
After having carried out an adjustment and before using the
wheelchair, make sure that all hardware is tight. Make sure
that all functions are secure before using the wheelchair.
The adjustments of your wheelchair must be made
by a health care professional. Inadequate adjustments can
cause wounds and/or damage to the user, the caregiver, the
wheelchair or the environment.
4.1 FOOTREST
4.1.1 LEGREST LENGHT ADJUSTMENT
Figure 1 : To change legrest length.
a) To adjust the length of all types of footrest (see; figure 1):
1. Remove the (A) adjustment screw, using a 7/16" wrench;
2. Adjust the telescopic tubing (C) at the needed length;
3. Put back the (A) screw and tighten firmly
TELESCOPIC
TUBING
C
A
B
4 SETUP INSTRUCTIONS
inc All rights reserved
14
4.1.2 CHANGING FOOTPLATE ANGLE
1. Loosen screw (B) using a 10 mm key;
2. Adjust the footplate at the needed angle;
3. Tighten screw (B) firmly (tighten at 140 Pounds/inch).
Figure 2 : Changing footplate angle.
4.1.3 CHANGING POSITION (DEPTH) OF THE COMPOSITE FOOTPLATE
1. Remove the two (2) Phillips screws (A) at the end of the footplate (see; figure 2);
2. Pull the footplate to release it from the support;
3. Readjust the footplate at the needed depth;
4. Replace the end part of the footplate with the (2) Phillips screws (A).
Aluminum footplate
B
COMPOSITE FOOTPLATE
INSERTION GROOVE
A
4 SETUP INSTRUCTIONS
inc All rights reserved
15
4.1.4 CHANGING CALF PAD HEIGHT
NOTE: The calf pad is adjustable in height, depth and width (see; figure 3).
a) To adjust calf pad height:
1. Loosen screw (A) using a 5 mm Allen key;
2. Slide support (B) until you reach the needed position;
3. Put back screw (A) and tighten firmly.
NOTE: The calf pad is not adjustable in height with the articulated legrest.
Figure 3 : Calf pad adjustment.
4.1.5 CHANGING CALF PAD POSITIONS
a) To adjust calf pad width (see; figure 3):
1. Loosen screws (C) using a 4 mm Allen key;
2. Slide calf pad (D) until you reach the needed position;
3. Tighten screws (C).
b) To adjust calf pad depth (see; figure 3):
1. Loosen screw (E) using a 5 mm Allen key;
2. Loosen screw (F);
3. Adjust at the needed position and tighten screws (E) and (F).
AB
C
D
E
F
4 SETUP INSTRUCTIONS
inc All rights reserved
16
4.2 ADJUSTABLE «U» SHAPE ARMREST HEIGHT
4.2.1 TO PROHIBIT REMOVING THE ARMREST
The (A) screw located at the base of the armrest, gives the possibility of installing in a
permanent way the armrest to the wheelchair. This removes the "DETACHABLE" function
of the armrest while preserving the swingaway possibility. Loosen the counter-nut (8 mm
key), and screw (4 mm Allen key) the bolt (A) in the hole and tighten the counter-nut
(see; figure 4-A).
Figure 4-A : To block the possibility of taking off the "U" shape armrest.
4.2.2 TO PROHIBIT ADJUSTMENT IN HEIGHT
The screw (A) located at the back of the armrest gives the possibility of prohibiting
the adjustment in height of the armrest. To prohibit the height adjustment, loosen
the counter-nut (8 mm key), screw (4 mm Allen key) the bolt (A) in the hole and
tighten the counter-nut (see; figure 4-B).
Figure 4-B : To block the height adjustment of the "U" shape armrest.
A
A
4 SETUP INSTRUCTIONS
inc All rights reserved
17
4.3 TELESCOPIC ARMREST «T» SHAPE
4.3.1 TO LIMIT THE TELESCOPIC ARMREST HEIGHT ADJUSTMENT
Figure 5: Armrest height adjustment limitation.
It is possible to limit the telescopic armrest height adjustment. You just have to move the
(2) limitation blocks, using a 5/32” Allen key and tighten them at the needed position
(see; figure 5).
NOTE : This armrest is not removable.
4 SETUP INSTRUCTIONS
inc All rights reserved
18
4.4 DYNAMIC BACKREST
4.4.1 DYNAMIC BACKREST INSTALLATION
POSITION ANGLE
1 90° (std)
2 95°
3 100°
4 NON-
AVAILABLE
5 NON-
AVAILABLE
6 NON-
AVAILABLE
7
NON-
AVAILABLE
Figure 6-A: Dynamic backrest angles adjustment positions.
NOTE :
The way to change the dynamic backrest angle, is the same as per section
4.5.1, the only difference with the dynamic backrest is to don’t forget to move the nylon
washers (C) following the new angle position (see; figure 6-B).
Consult the figure 6-A above to know the possible adjustment angles and to
tighten the screws at 20 pounds/inch.
It is important to use only the 1 to 3 positions of the figure 6-A
table above, to not damage the dynamic backrest system.
The adjustments of your wheelchair must be made by
a health care professional. Inadequate adjustments can cause
wounds and/or damage to the user, the caregiver, the
wheelchair or the environment.
4 SETUP INSTRUCTIONS
inc All rights reserved
19
Figure 6-B: Dynamic backrest installation on the wheelchair.
1. Determine at which angle the backrest should be installed.
2. Take the backrest structure tubing (G) and insert the compression piston (D) equal
to the oblong hole in the same way as shown at figure 6-B. The compression
piston (D) should be sprayed with grease before insertion.
3. Spray with grease the 4 nylon washers (C) and put two of them on the inside in
line with the bottom holes on the anchor structure (H). The grease should retain
the nylon washers stick to the anchor structure (H) (see; figure 6-B).
4. Take the backrest structure tubing (G) with the compression piston (D) and install
it on the anchor structure (H). Once that the two (C) nylon washers, the
compression piston (D) and the oblong hole on the backrest structure tubing will
be all aligned, insert the (A) screw, the (B) nut and tighten, using two 7/16" key.
NOTE: Tighten the screws at 20 pounds/inch. This tightening force should
allow the dynamic backrest assembly to move freely.
5. Take the two others (C) nylon washers and put them on the inside in line with the
adjustment angle holes on the anchor structure (H).
4 SETUP INSTRUCTIONS
inc All rights reserved
20
6. Adjust the backrest structure tubing (G) at the desired angle and once the (C)
nylon washers and the holes in the backrest structure tubing (G) will be all aligned,
insert the full threaded (A) screw and tighten the (B) nut, using two 7/16" key (see;
the note at step 4, in reference to know about the tightening force to use).
7. Insert the (E) spring beforehand sprayed with grease in the bottom part of the
backrest structure tubing (G) shown at figure 6-B.
8. Spray with grease the threaded part of the spring tension adjustment handle (F).
9. Screw the spring tension adjustment handle (F) on the bottom part of the backrest
structure tubing (G) until you can see only two threads (this is the NEUTRAL
position at this position the spring is not compressed yet).
4.4.2 DYNAMIC BACKREST ADJUSTMENT
It is possible to choose 3 different types of springs with the dynamic backrest. 3 springs
with different compression hardness. The RED spring (soft tension), the BRONZE spring
(regular tension) and the GREEN spring (hard tension).
1. Insert the selected (E) spring in the bottom part of the backrest structure tubing
(G) and screw the spring tension adjustment handle (F) until you can not see any
threads (the spring will be a little bit compressed) (see; figure 6-B).
2. Refer to the graduated sticker (I) to know the maximum compression of each
springs (see; figure 6-B). For example; the green spring, will reach its maximum
compression, when the handle (F) will be in line with the number 3 on the sticker
(I).
3. The final adjustment will depend on each user comfort. Moreover, this adjustment
could be different on each backrest post.
Never put your hands on the spring tension adjustment
handle (F) during somebody use the dynamic backrest.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93

Orthofab Tango User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI