GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
2,000 200
7
45
3/24/2010
11645
90
217380
Parts List DESCRIPTION
PART NUMBER
QTY
ITEM HEX BOLTM12-1.25 x 30mm21 LOCK WASHER1/2"62 HEX BOLTM12 - 1.25 x 40 HEX
4
3WASHER7/16
44 HANDLE NUT
1/2-13
25
1. Position the hitch on the bumper so the hitch plate holes align with the threaded holes in front face of
the bumper. At the bottom of the bumper, mark metal retainer strip and plastic fascia around the hitch
bumper bracket. This area (approximately 1 1/2 x 8") must be clear for hitch bumper bracket to fit
directly against metal bumper. Retainer is removed from bumper for cutting and fascia trimmed with a sharp
knife. Use 10mm wrench to remove the retainer.
2A. Note the holes in the bottom of the metal bumper that match holes in hitch bumper bracket. For those
bumpers with existing 12mm weldnuts in the bottom, the hitch can be bolted directly in place using
supplied M12 bolts, 7/16" flat washers, and 7/16" lock washers as shown. If vehicle bumper does not have
12mm weldnuts at the bottom surface, go to 2B.
2B. Some bumpers will have smaller weld nuts for the retainer, or no holes in bottom of bumper. If equipped,
remove the (2) small weldnuts with a drift pin. Using the hitch as a template drill 1/2" diameter holes in metal
bumper. Fasten hitch to the vehicle bumper using M12 hex bolts, 7/16" flat washers, 7/16" lock washers and
M12 handle nuts as shown. M12 handle nuts and flat washers must be placed as shown in diagram INSIDE
of bumper through access holes in the front face of bumper.
3. Install M12 and 7/16" lock washers into existing weldnuts as shown.
4. Torque all 12mm fasteners to 65 lb-ft.
ACCESS HOLE
BUMPER
-DRILLING MAY BE REQUIRED
-FASCIA TRIMMING REQUIRED
3
4
3
2
4
EXISTING WELDNUTS
1
2
5
89-92 CHEVY PRISM / 87-92 TOYOTA COROLLA SEDAN & WAGON
2A
2B
REMOVE EXISTING
SMALL WELDNUT
(IF EQUIPPED)
DRILL HOLES BUMPER BRACKET
2
-
1
