Digi RCM6600W User manual

Integrated C Development System

For Rabbit

®

4000, 5000 and 6000 Microprocessors

User’s Manual

019-0167_L

The latest revision of this manual is available on the Digi website:

www.digi.com.

Dynamic C User’s Manual

Part Number 019-0167 • Printed in the U.S.A.

Digi International Inc. reserves the right to make changes and

improvements to its products without providing notice.

Trademarks

Rabbit

®

and Dynamic C

®

are registered trademarks of Digi International Inc.

Windows

®

is a registered trademark of Microsoft Corporation

Dynamic C User’s Manual digi.com 3

TABLE OF CONTENTS

Chapter 1. Installing Dynamic C

1.1 Requirements

...............................................8

1.2 Assumptions ................................................8

2. Introduction to Dynamic C

2.1 The Nature of Dynamic C

.........................9

2.1.1 Speed ...................................................9

2.2 New Features from ANSI C....................10

2.3 Dynamic C Enhancements and Differenc-

es

.......................................................................11

3. Quick Tutorial

3.1 Run DEMO1.C

..........................................13

3.1.1 Single Stepping ..................................14

3.1.2 Watch Expression ..............................14

3.1.3 Breakpoint .........................................14

3.1.4 Editing the Program ...........................15

3.2 Run DEMO2.C..........................................15

3.2.1 Watching Variables Dynamically ......15

3.3 Run DEMO3.C..........................................16

3.3.1 Cooperative Multitasking ..................16

3.4 Summary of Features ...............................17

4. Language

4.1 Storage Classes

.........................................19

4.2 Pointers.......................................................19

4.3 Far Pointers and Far Data........................20

4.3.1 The far Qualifier ................................20

4.3.2 Basic Declarations .............................20

4.3.3 Multi-Level Far Pointers ...................21

4.3.4 Arrays and Structures ........................21

4.3.5 Complex Declarations .......................22

4.3.6 Sample Programs ...............................22

4.4 The const Keyword...................................23

4.4.1 Simple Constants ...............................23

4.4.2 Const and Pointers .............................23

4.4.3 Const Conversions, Casting, and

Parameter Passing ............................25

4.4.4 Dynamic C Version Differences ....... 28

4.5 Pointers to Functions, Indirect Calls...... 29

4.6 Function Chaining .................................... 31

4.7 Global Initialization ................................. 32

4.8 Libraries ..................................................... 33

4.8.1 Libraries and File Scope .................... 34

4.8.2 LIB.DIR ............................................. 35

4.9 Headers....................................................... 36

4.10 Modules ...................................................36

4.10.1 The Parts of a Module ..................... 36

4.10.2 Module Sample Code ......................38

4.10.3 Important Notes ............................... 39

4.11 Function Description Headers.............. 40

4.12 Support Files ...........................................40

5. Multitasking with Dynamic C

5.1 Cooperative Multitasking

........................41

5.2 A Real-Time Problem.............................. 42

5.2.1 Solving the Real-Time Problem

with a State Machine ....................... 43

5.3 Costatements ............................................. 43

5.3.1 Solving the Real-Time Problem

with Costatements ............................44

5.3.2 Costatement Syntax ........................... 44

5.3.3 Control Statements ............................45

5.4 Advanced Costatement Topics............... 47

5.4.1 The CoData Structure ........................ 48

5.4.2 CoData Fields .................................... 48

5.4.3 Pointer to CoData Structure .............. 49

5.4.4 Functions for Use With Named

Costatements .................................... 49

5.4.5 Firsttime Functions ............................ 50

5.4.6 Shared Global Variables ....................50

5.5 Cofunctions ............................................... 50

5.5.1 Cofunction Syntax ............................. 52

5.5.2 Calling Restrictions ........................... 52

5.5.3 CoData Structure ............................... 53

5.5.4 Firsttime Functions ............................ 53

Dynamic C User’s Manual digi.com 4

5.5.5 Types of Cofunctions ........................54

5.5.6 Types of Cofunction Calls .................55

5.5.7 Special Code Blocks ..........................56

5.5.8 Solving the Real-Time Problem

with Cofunctions ..............................58

5.6 Patterns of Cooperative Multitasking....58

5.7 Timing Considerations.............................59

5.7.1 waitfor Accuracy Limits ....................59

5.8 Overview of Preemptive Multitasking ..60

5.9 µC/OS-II ....................................................60

5.9.1 Changes to µC/OS-II .........................60

5.9.2 Tasking Aware Interrupt Service

Routines (TA-ISR) ...........................62

5.9.3 Library Reentrancy ............................68

5.9.4 How to Get a µC/OS-II Application

Running ............................................68

5.9.5 Compatibility with TCP/IP ................73

5.9.6 Debugging Tips .................................74

5.10 Summary..................................................74

6. Debugging with Dynamic C

6.1 Debugging Features of Dynamic C

........77

6.2 Debugging Tools ......................................79

6.2.1 printf() ................................................79

6.2.2 ANSI Escape Sequences ....................80

6.2.3 Software Breakpoints ........................81

6.2.4 Hardware Breakpoints .......................82

6.2.5 Single Stepping ..................................84

6.2.6 Watch Expressions ............................85

6.2.7 Evaluate Expressions .........................86

6.2.8 Memory Dump ..................................86

6.2.9 MAP File ...........................................87

6.2.10 Symbolic Stack Trace ......................90

6.2.11 Assert Macro ...................................91

6.2.12 Miscellaneous Debugging Tools .....91

6.3 Where to Look for Debugger Features..94

6.3.1 Run and Inspect Menus .....................95

6.3.2 Options Menu ....................................95

6.3.3 Window Menu ...................................95

6.4 Debug Strategies.......................................96

6.4.1 Good Programming Practices ............96

6.4.2 Finding the Bug .................................98

6.5 Reference to Other Debugging Informa-

tion

....................................................................99

7. The Virtual Driver

7.1 Default Operation

...................................100

7.2 Calling _GLOBAL_INIT()................... 100

7.3 Global Timer Variables......................... 101

7.3.1 Example: Timing Loop ................... 101

7.3.2 Example: Delay Loop ..................... 102

7.4 Watchdog Timers ................................... 103

7.4.1 Hardware Watchdog ........................ 103

7.4.2 Virtual Watchdogs .......................... 103

7.5 Preemptive Multitasking Drivers......... 103

8. The Slave Port Driver

8.1 Slave Port Driver Protocol

.................... 104

8.1.1 Overview ......................................... 104

8.1.2 Registers on the Slave ..................... 105

8.1.3 Polling and Interrupts ...................... 106

8.1.4 Communication Channels ............... 106

8.2 Functions ................................................. 107

8.3 Examples ................................................. 111

8.3.1 Status Handler ................................. 111

8.3.2 Serial Port Handler .......................... 111

8.3.3 Byte Stream Handler ....................... 123

9. Run-Time Errors

9.1 Run-Time Error Handling

..................... 131

9.1.1 Error Code Ranges .......................... 131

9.1.2 Fatal Error Codes ............................ 132

9.2 User-Defined Error Handler ................. 133

9.2.1 Replacing the Default Handler ........ 133

9.3 Run-Time Error Logging ...................... 134

9.3.1 Error Log Buffer ............................. 134

9.3.2 Initialization and Defaults ............... 135

9.3.3 Configuration Macros ..................... 135

9.3.4 Error Logging Functions ................. 136

9.3.5 Examples of Error Log Use ............. 136

10. Memory Management

10.1 Memory Map

........................................ 137

10.1.1 Memory Mapping Control ............ 138

10.2 Extended Memory Functions ............. 138

10.3 Code Placement in Memory ............... 138

10.4 Dynamic Memory Allocation............. 139

11. Direct Memory Access

11.1 DMA Registers and Global Resources ...

140

11.2 API Functions ....................................... 140

Dynamic C User’s Manual digi.com 5

11.3 DMA Interrupts ....................................141

11.4 DMA Transfer Information.................141

11.4.1 DMA Transfer Priority ..................141

11.4.2 DMA Transfer Mode .....................142

11.4.3 DMA Transfer Functions ..............142

11.4.4 DMA Transfer Function Flags ......142

11.5 DMA with Ethernet..............................142

12. FAT File System

12.1 Overview of FAT Documentation

.....144

12.2 Running Your First FAT Sample Pro-

gram

...............................................................144

12.2.1 Bringing Up the File System .........145

12.2.2 Using the File System ....................148

12.3 More Sample Programs .......................151

12.3.1 Blocking Sample ...........................151

12.3.2 Non-Blocking Sample ...................153

12.4 FAT Operations ....................................157

12.4.1 Format and Partition the Device ....157

12.4.2 File and Directory Operations ....... 159

12.5 More FAT Information........................168

12.5.1 Clusters and Sectors ......................168

12.5.2 The Master Boot Record ...............168

12.5.3 FAT Partitions ...............................169

12.5.4 Directory and File Names ..............172

12.5.5 µC/OS-II and FAT Compatibility .172

12.5.6 SF1000 and FAT Compatibility ....172

12.5.7 Hot-Swapping an xD Card ............172

12.5.8 Hot-Swapping an SD Card ............173

12.5.9 Unsupported FAT Features ...........173

12.5.10 References ...................................174

13. Using Assembly Language

13.1 Mixing Assembly and C

......................175

13.1.1 Embedded Assembly Syntax .........175

13.1.2 Embedded C Syntax ......................176

13.1.3 Setting Breakpoints in Assembly ..176

13.1.4 Assembly and 32-bit Pointer Registers

(PW, PX, PY, PZ) ..........................177

13.2 Assembler and Preprocessor...............178

13.2.1 Comments ......................................178

13.2.2 Defining Constants ........................178

13.2.3 Multiline Macros ...........................180

13.2.4 Labels ............................................180

13.2.5 Special Symbols ............................181

13.2.6 C Variables ....................................181

13.3 Stand-Alone Assembly Code..............182

13.3.1 Stand-Alone Assembly Code in

Extended Memory ......................... 183

13.3.2 Example of Stand-Alone Assembly

Code ............................................... 183

13.3.3 The Stack Frame ........................... 184

13.3.4 Embedded Assembly Example ..... 185

13.3.5 The Disassembled Code Window . 186

13.3.6 Local Variable Access ................... 187

13.4 C Calling Assembly............................. 189

13.4.1 Passing Parameters ........................ 189

13.4.2 Location of Return Results ............ 190

13.4.3 Returning a Structure .................... 190

13.5 Assembly Calling C............................. 191

13.6 Interrupt Routines in Assembly ......... 191

13.6.1 Steps Followed by an ISR ............. 192

13.6.2 Modifying Interrupt Vectors ......... 192

13.7 Common Problems............................... 195

14. Keywords

abandon ........................................................ 196

abort.............................................................. 196

align.............................................................. 197

always_on..................................................... 197

anymem ........................................................ 197

asm ............................................................... 198

auto............................................................... 198

bbram............................................................ 198

break............................................................. 199

c.................................................................... 199

case............................................................... 199

char............................................................... 200

cofunc........................................................... 200

const ............................................................. 201

continue........................................................ 201

costate........................................................... 201

debug............................................................ 202

default........................................................... 202

do.................................................................. 202

else................................................................ 203

enum............................................................. 203

extern............................................................ 203

far ................................................................. 204

firsttime ........................................................ 207

float .............................................................. 207

for ................................................................. 208

goto............................................................... 208

if ................................................................... 208

.init_on ......................................................... 209

int.................................................................. 209

interrupt........................................................ 209

__lcall__....................................................... 209

long............................................................... 210

main.............................................................. 210

nodebug........................................................ 210

norst.............................................................. 211

nouseix ......................................................... 211

NULL ........................................................... 211

protected....................................................... 212

register.......................................................... 212

return ............................................................ 213

Dynamic C User’s Manual digi.com 6

root................................................................213

scofunc..........................................................213

segchain ........................................................214

shared............................................................214

short ..............................................................214

size................................................................215

signed............................................................215

sizeof ............................................................215

speed.............................................................215

static..............................................................216

struct .............................................................216

switch............................................................217

typedef ..........................................................217

union.............................................................218

unsigned........................................................218

useix..............................................................218

waitfor ..........................................................219

waitfordone

(wfd) ........................................................219

while .............................................................220

xdata .............................................................220

xmem ............................................................221

void...............................................................221

volatile ..........................................................222

xstring...........................................................222

yield ..............................................................222

14.1 Compiler Directives .............................223

#asm..............................................................223

#class ............................................................223

#debug

#nodebug .................................................224

#define ..........................................................224

#endasm........................................................224

#error ............................................................224

#fatal.............................................................225

#funcchain ....................................................225

#GLOBAL_INIT..........................................225

#if

#elif

#else

#endif .......................................................226

#ifdef ............................................................226

#ifndef ..........................................................227

#include ........................................................227

#interleave

#nointerleave ...........................................227

#makechain...................................................228

#memmap .....................................................228

#pragma ........................................................228

#undef...........................................................228

#use...............................................................229

#useix

#nouseix...................................................229

#warns ..........................................................229

#warnt...........................................................229

#ximport .......................................................230

#zimport........................................................230

15. Operators

15.1 Arithmetic Operators

...........................232

+....................................................................232

– ....................................................................232

*.................................................................... 233

/..................................................................... 233

++ ................................................................. 234

––.................................................................. 234

% .................................................................. 234

15.2 Assignment Operators ......................... 235

= ................................................................... 235

+= ................................................................. 235

-= .................................................................. 235

*= ................................................................. 235

/= .................................................................. 235

%= ................................................................ 235

<<=............................................................... 235

>>=............................................................... 235

&= ................................................................ 236

^=.................................................................. 236

|=................................................................... 236

15.3 Bitwise Operators................................. 236

<< ................................................................. 236

>> ................................................................. 236

&................................................................... 237

^.................................................................... 237

|..................................................................... 237

~.................................................................... 237

15.4 Relational Operators ............................ 238

< ................................................................... 238

<= ................................................................. 238

> ................................................................... 238

>= ................................................................. 238

15.5 Equality Operators ............................... 239

== ................................................................. 239

!= .................................................................. 239

15.6 Logical Operators................................. 240

&&................................................................ 240

|| .................................................................... 240

! .................................................................... 240

15.7 Postfix Expressions.............................. 240

( ) .................................................................. 240

[ ] .................................................................. 240

. (dot)............................................................ 241

-> .................................................................. 241

15.8 Reference/Dereference Operators...... 242

&................................................................... 242

*.................................................................... 242

15.9 Conditional Operators ......................... 243

? :.................................................................. 243

15.10 Other Operators .................................. 244

(type) ............................................................ 244

sizeof ............................................................ 244

,..................................................................... 245

16. Graphical User Interface

16.1 The GUI Environment

......................... 246

16.1.1 Editing ........................................... 246

Dynamic C User’s Manual digi.com 7

16.1.2 Menus ............................................247

16.1.3 Using Keyboard Shortcuts .............247

16.1.4 Editor Window Popup Menu .........248

16.2 File Menu...............................................249

16.3 Edit Menu ..............................................251

16.4 Compile Menu ......................................254

16.5 Run Menu ..............................................256

16.6 Inspect Menu........................................259

16.7 Options Menu........................................263

16.7.1 Environment Options .....................263

16.7.2 Project Options ..............................280

16.7.3 Toolbars .........................................294

16.8 Window Menu ......................................296

16.9 Help Menu.............................................303

17. Command Line Interface

17.1 Default States

........................................306

17.2 User Input ..............................................306

17.3 Saving Output to a File........................307

17.4 Command Line Switches ....................307

17.4.1 Switches Without Parameters ........307

17.4.2 Switches Requiring a Parameter ....314

17.5 Examples................................................319

17.6 Command Line RFU............................319

18. Project Files

18.1 Project File Names

...............................322

18.1.3 Active Project ................................322

18.2 Updating a Project File........................323

18.3 Menu Selections ...................................323

18.4 Command Line Usage .........................324

19. Hints and Tips

19.1 A User-Defined BIOS

..........................325

19.2 Efficiency...............................................326

19.2.1 Nodebug Keyword .........................326

19.2.2 In-line I/O ......................................327

19.3 Run-time Storage of Data....................327

19.3.1 User Block .....................................327

19.3.2 Battery-Backed RAM ....................327

19.4 Root Memory Reduction Tips ............328

19.4.1 Increasing Root Code Space ..........328

19.4.2 Increasing Root Data Space ...........329

Appendix A. Macros and Global Variables

A.1 Macros Defined by the Compiler........331

A.2 Macros Defined in the BIOS or

Configuration Libraries ...........................332

A.3 Global Variables .................................333

A.4 Exception Types .................................334

A.5 Rabbit Registers..................................334

A.5.1 Shadow Registers ............................ 334

Appendix B. Map File Generation

B.1 Grammar .............................................335

Appendix C. Security Software & Utility

Programs

C.1 Dynamic C Utilities ............................336

C.0.1 Rabbit I/O LIB Utility ..................... 336

C.0.2 Library File Encryption ................... 337

C.0.3 File Compression Utility ................. 338

C.0.4 Font and Bitmap Converter Utility.. 340

C.0.5 Rabbit Field Utility Module ............ 340

Software License Agreement .............. 344

Index...................................................... 347

Dynamic C User’s Manual digi.com 8

CHAPTER 1. INSTALLING DYNAMIC C

Insert the installation disk or CD in the appropriate disk drive on your PC. The installation should begin

automatically. If it doesn’t, issue the Windows “Run...” command and type the following command:

‹disk›:\SETUP

The installation program will begin and guide you through the installation process.

1.1 Requirements

Dynamic C requires an IBM-compatible PC running Windows 2000 or later with at least one free COM or

USB port.

Please note that Windows Vista is supported by Dynamic C out of the box if there is only one processor in

the host PC or laptop. With multiple processors (a.k.a., dual cores) present in the host system, you must

check Windows “Processor Affinity” setting in order to ensure Vista compatibility with Dynamic C. Techni-

cal note TN257 “Running Dynamic C with Windows Vista” has instructions for modifying the “Processor

Affinity” setting. This technical note is available on the Digi website:

www.digi.com/support/

(Scroll to and select the product Rabbit Dynamic C 10 and click on the “Documentation” link.)

Starting with Dynamic C 10.21, the “Processor Affinity” setting is set automatically.

1.2 Assumptions

It is assumed that the reader has a working knowledge of:

• The basics of operating a software program and editing files under Windows on a PC.

• Programming in a high-level language.

• Assembly language and architecture for controllers.

Refer to one or both of the following texts for a full treatment of C:

• The C Programming Language by Kernighan and Ritchie (published by Prentice-Hall).

• C: A Reference Manual by Harbison and Steel (published by Prentice-Hall).

Dynamic C User’s Manual digi.com 9

2. INTRODUCTION TO DYNAMIC C

Dynamic C is an integrated development system for writing embedded software. It is designed for use with

Rabbit controllers and other controllers based on the Rabbit microprocessor.

2.1 The Nature of Dynamic C

Dynamic C integrates the following development functions into one program:

• Editing

• Compiling

• Linking

• Loading

• Debugging

Dynamic C has an easy-to-use, built-in, full-featured text editor. Dynamic C programs can be executed and

debugged interactively at the source-code or machine-code level. Pull-down menus and keyboard short-

cuts for most commands make Dynamic C easy to use.

Dynamic C also supports assembly language programming. It is not necessary to leave C or the develop-

ment system to write assembly language code. C and assembly language may be mixed together.

Debugging under Dynamic C includes the ability to use printf commands, watch expressions, break-

points and stack tracing. Watch expressions can be used to compute C expressions involving the target’s

program variables or functions. Watch expressions can be evaluated while stopped at a breakpoint or while

the target is running its program. Stack tracing shows function call sequences and parameter values.

Dynamic C provides extensions to the C language (such as shared and protected variables, costatements

and cofunctions) that support real-world embedded system development. Dynamic C supports cooperative

and preemptive multitasking.

Dynamic C comes with many function libraries, all in source code. These libraries support real-time pro-

gramming, machine level I/O, and provide standard string and math functions.

2.1.1 Speed

Dynamic C compiles directly to memory. Functions and libraries are compiled and linked and downloaded

on-the-fly. On a fast PC, Dynamic C might load 30,000 bytes of code in five seconds at a baud rate of

115,200 bps.

Dynamic C User’s Manual digi.com 10

2.2 New Features from ANSI C

New features from ANSI/ISO C90 are gradually being added to Dynamic C.

The following features were introduced in Dynamic C 10.60:

• Variable initializer support: Variables can now be initialized within a declaration.

• Preprocessor support for the "defined" keyword: The "defined" keyword can now be used in #if /

#elif expressions to determine whether a macro has been previously defined.

• #include support: The standard C mechanism of using "#include" to include other source files is now

supported.

The following feature was introduced with Dynamic C 10.62:

• Function pointer parameter list checking: Function pointers may now contain a parameter list, and

the compiler will check the parameters and perform automatic type promotion when a function is called

through the function pointer.

The following features were introduced with Dynamic C 10.64:

• "File Scoping: In projects using multiple .C files, each C source file now defines a new scope separate

from all other C files. Using the static keyword ensures that file-scope variables and functions are

visible only within the file in which they are defined. Omitting the static or using extern will link

those symbols to other files where they are used. The new functionality obeys the ANSI-C rules for file

scoping for .C and .H files. The Dynamic C extension #use (which works with .LIB files) works with

the new scoping with some important caveats noted in section 4.7 "Libraries".

• "Nested/block Scoping: Nested, or block, scoping allows the declaration of variables within a curly-

brace-delimited block. Previously, Dynamic C only allowed declarations at the beginning of a function

block (as defined by the original K&R C specification). In addition, #asm assembly blocks now each

have their own local (function) block scope preventing name collisions between global and local

assembly labels.

• "Const Correctness: Dynamic C now handles the functionality of the const keyword as it is defined

in the ANSI-C89/ISO-C90 specification. See Section 4.4 “The const Keyword” for information on the

differences between the older Dynamic C functionality and the new ANSI functionality.

• "signed Keyword: The signed keyword is now supported. Variables of type char can also now

be signed; previously, char variables could only be unsigned.

Dynamic C User’s Manual digi.com 11

2.3 Dynamic C Enhancements and Differences

Dynamic C offers a number of extensions to the standard C language. These extensions are targeted for

making your embedded development easier.

2.3.1 Dynamic C Enhancements

Many enhancements have been added to Dynamic C. Some of these are listed below.

• Dynamic C 10.54 introduces remote firmware updates for some board types. Please see AN421

“Remote Program Update” for more information. This document is available on the Dynamic C soft-

ware CD and on the Digi support website:

www.digi.com/support/

(Scroll to and select the product Rabbit Dynamic C 10 and click on the “Documentation” link.)

• Function Chaining, a concept unique to Dynamic C, allows special segments of code to be embedded

within one or more functions. When a named function chain executes, all the segments belonging to

that chain execute. Function chains allow software to perform initialization, data recovery, or other

kinds of tasks on request. Dynamic C also provides a special function chain called _GLOBAL_INIT

which can be used for initialization code. The _GLOBAL_INIT function chain is executed at the start

of the program. Dynamic C also provides a special function chain called _GLOBAL_INIT which can

be used for initialization code. The _GLOBAL_INIT function chain is executed at the start of the pro-

gram.

• Costatements allow cooperative, parallel processes to be simulated in a single program.

• Cofunctions allow cooperative processes to be simulated in a single program.

• Dynamic C supports embedded assembly code and stand-alone assembly code.

• Dynamic C has keywords that help protect data shared between different contexts (shared) or stored in

battery-backed memory (protected).

• Dynamic C has a set of features that allow the programmer to make the fullest use of xmem (extended

memory). Up until the release of Dynamic C 10.21, the compiler supported a 1 MB physical address

space. Starting with Dynamic C 10.21, the compiler supports up to the 16 MB of physical memory; up

to 16 MB can be used for data and up to 1 MB can be used for code. (Dynamic C has been verified to

work with Rabbit-based boards with up to 4.5 MB of memory.)

Normally, Dynamic C takes care of memory management, but there are instances where the program-

mer will want to take control of it. Dynamic C has keywords and directives to help put code and data in

the proper place, such as: root, xmem, and #memmap for code and far for data.

See Chapter 10 for further details on memory management.

• The #use statement allows you to create library files that include your function declarations and defini-

tions together. Starting with Dynamic C 10.60, you can use the standard #include mechanism instead.

2.3.2 Dynamic C Differences

The main differences in Dynamic C are summarized in the list below and discussed in detail in Chapter 4.

“Language” and Chapter 14. “Keywords.”

• Bit fields are not supported.

• Separate compilation of different parts of the program is not supported.

Dynamic C User’s Manual digi.com 12

3. QUICK TUTORIAL

Sample programs are provided in the Dynamic C Samples folder, which is in the root directory where

Dynamic C was installed. The Samples folder contains many subfolders, as shown in Figure 3.1. Sample

programs are provided in source code format. You can open the source code file in Dynamic C and read

the comment block at the top of the sample program for a description of its purpose and other details.

Comments are also provided throughout the source code. This documentation, provided by the software

engineers, is a rich source of information.

Figure 3.1 Screenshot of Samples Folder

The subfolders contain sample programs that illustrate the use of the various Dynamic C libraries. For

example, the subfolders “Cofunc” and “Costate” have sample programs illustrating the use of

COFUNC.LIB and COSTATE.LIB, libraries that support cooperative multitasking using Dynamic C lan-

guage extensions. Besides its subfolders, the Samples folder also contains some sample programs to dem-

onstrate various aspects of Dynamic C. For example, the sample program Pong.c demonstrates output

to the Stdio window.

In the rest of this chapter we examine three sample programs in some detail.

Dynamic C User’s Manual digi.com 13

3.1 Run DEMO1.C

This sample program will be used to illustrate some of the functions of Dynamic C. Open the file

Samples/DEMO1.C using the File menu or the keyboard shortcut <Ctrl+O>. The program will appear

in a window, as shown in Figure 3.2 (minus some comments). Use the

mouse to place the cursor on the

function name

printf

in the program and press

<Ctrl+H>

.

This brings up a Function Description window

for printf(). You can do this with all functions in the Dynamic C libraries, including libraries you

write yourself.

Figure 3.2 Sample Program DEMO1.C

To run DEMO1.C compile it using the Compile menu, and then run it by selecting “Run” in the

Run menu. (The keyboard shortcut <F9> will compile and run the program. You may also use the

green triangle toolbar button as a substitute for <F9>.)

The value of the counter should be printed repeatedly to the Stdio window if everything went well. If this

doesn’t work, review the following points:

• The target should be ready, indicated by the message “BIOS successfully compiled...” If you did not

receive this message or you get a communication error, recompile the BIOS by pressing <Ctrl+Y> or

select “Reset Target / Compile BIOS” from the Compile menu.

• A message reports “No Rabbit Processor Detected” in cases where the wall transformer is not con-

nected or not plugged in.

• The programming cable must be connected to the controller. (The colored wire on the programming

cable is closest to pin 1 on the programming header on the controller). The other end of the program-

Dynamic C User’s Manual digi.com 14

ming cable must be connected to the PC serial port. The COM port specified in the Communications

dialog box must be the same as the one the programming cable is connected to. (The Communications

dialog box is accessed via the Communications tab of the Options | Project Options menu.)

• To check if you have the correct serial port, press <Ctrl+Y>. If the “BIOS successfully compiled …”

message does not display, choose a different serial port in the Communications dialog box until you

find the serial port you are plugged into. Don’t change anything in this menu except the COM number.

The baud rate should be 115,200 bps and the stop bits should be 1.

3.1.1 Single Stepping

To experiment with single stepping, we will first compile DEMO1.C to the target without running

it. This can be done by clicking the compile button on the task bar. This is the same as pressing F5.

Both of this actions will compile according to the setting of “Default Compile Mode.” (See

“Default Compile Mode” in Chapter 16, for how to set this parameter.) Alternatively you may

select

Compile | Compile to Target from the main menu.

After the program compiles a highlighted character (green) will appear at the first executable

statement of the program. Press the <F8> key to single step (or use the toolbar button). Each time

the <F8> key is pressed, the cursor will advance one statement. When you get to the statement:

for(j=0, j< ... , it becomes impractical to single step further because you would have to

press <F8> thousands of times. We will use this statement to illustrate watch expressions.

3.1.2 Watch Expression

Watch expressions may only be added, deleted or updated in run mode. To add a watch expression

click on the toolbar button pictured here, or press <Ctrl+W> or choose “Add Watch” from the

Inspect menu. The Add Watch Expression popup box will appear. Type the lower case letter “j”

and click on either “Add” or “OK.” The former keeps the popup box open, the latter closes it.

Either way the Watches window appears. This is where information on watch expressions will be

displayed. Now continue single stepping. Each time you do, the watch expression (j) will be eval-

uated and printed in the Watches window. Note how the value of “j” advances when the statement

j++ is executed.

3.1.3 Breakpoint

Move the cursor to the start of the statement:

for (j=0; j<20000; j++);

To set a breakpoint on this statement, press <F2> or select “Toggle Breakpoint” from the Run menu. A red

highlight appears on the first character of the statement. To get the program running at full speed, press

<F9>. The program will advance until it hits the breakpoint. The breakpoint will start flashing both red and

green colors.

To remove the breakpoint, press <F2> or select “Toggle Breakpoint” on the Run menu. To continue pro-

gram execution, press <F9>. You will see the value of “i” displayed in the Stdio window repeatedly until

program execution is halted.

Dynamic C User’s Manual digi.com 15

You can set breakpoints while the program is running by positioning the cursor to a statement and using

the <F2> key. If the execution thread hits the breakpoint, a breakpoint will take place. You can toggle the

breakpoint with the <F2> key and continue execution with the <F9> key.

You can also set breakpoints while in edit mode. Breakpoint information is not only retained when going

back and forth from edit mode to debug mode, it is stored when a file is closed and restored when the file

is re-opened.

3.1.4 Editing the Program

Press <F4>to put Dynamic C into edit mode. Use the “Save as” choice on the File menu to save the file

with a new name so as not to change the original demo program. Save the file as MYTEST.C. Now change

the number 20000 in the for statement to 10000. Then use the <F9> key to recompile and run the pro-

gram. The counter displays twice as quickly as before because you reduced the value in the delay loop.

3.2 Run DEMO2.C

Go back to edit mode and open the program DEMO2.C. This program is the same as the first program,

except that a variable k has been added along with a statement to increment “k” by the value of “i” each

time around the endless loop. Compile and run DEMO2.C.

3.2.1 Watching Variables Dynamically

Press <Ctrl+W> to open the “Add Watch Expression” popup box.

Type “k” in the text entry box, then click “OK” (or “Add”) to add the expression “k” to the top of the list

of watch expressions. Now press <Ctrl+U>, the keyboard shortcut for updating the watch window. Each

time you press

<Ctrl+U>, you will see the current value of k.

Add another expression to the watch window:

k*5

Then press <Ctrl+U> several times to observe the watch expressions “k” and “k*5.”

Dynamic C User’s Manual digi.com 16

3.3 Run DEMO3.C

The example below, sample program DEMO3.C, uses costatements. A costatement is a way to perform a

sequence of operations that involve pauses or waits for some external event to take place.

3.3.1 Cooperative Multitasking

Cooperative multitasking is a way to perform several different tasks at virtually the same time. An exam-

ple would be to step a machine through a sequence of tasks and at the same time carry on a dialog with the

operator via a keyboard interface. Each separate task voluntarily surrenders its compute time when it does

not need to perform any more immediate activity. In preemptive multitasking control is forcibly removed

from the task via an interrupt.

Dynamic C has language extensions to support both types of multitasking. For cooperative multitasking

the language extensions are costatements and cofunctions. Preemptive multitasking is accomplished with

slicing or by using the µC/OS-II real-time kernel. The µC/OS-II real-time kernel is included with

Dynamic C starting with Dynamic C version 10.21. The other multitasking software has always shipped

with all versions of Dynamic C.

3.3.1.1 Advantages of Cooperative Multitasking

Unlike preemptive multitasking, in cooperative multitasking variables can be shared between different

tasks without taking elaborate precautions. Cooperative multitasking also takes advantage of the natural

delays that occur in most tasks to more efficiently use the available processor time.

The DEMO3.C sample program has two independent tasks. The first task prints out a message to Stdio

once per second. The second task watches to see if the keyboard has been pressed and prints the entered

key.

main() {

int secs; // seconds counter

secs = 0; // initialize counter

(1) while (1) { // endless loop

// First task will print the seconds elapsed.

(2) costate {

secs++; // increment counter

(3) waitfor( DelayMs(1000) ); // wait one second

printf("%d seconds\n", secs); // print elapsed seconds

(4) }

// Second task will check if any keys have been pressed.

costate {

(5) if ( !kbhit() ) abort; // key been pressed?

printf(" key pressed = %c\n", getchar() );

}

(6) } // end of while loop

}// end of main

Dynamic C User’s Manual digi.com 17

The numbers in the left margin are reference indicators and not part of the code. Load and run the pro-

gram. The elapsed time is printed to the Stdio window once per second. Push several keys and note how

they are reported.

The elapsed time message is printed by the costatement starting at the line marked (2). Costatements need

to be executed regularly, often at least every 25 ms. To accomplish this, the costatements are enclosed in a

while loop. The while loop starts at (1) and ends at (6). The statement at (3) waits for a time delay, in

this case 1000 ms (one second). The costatement executes each pass through the while loop. When a

waitfor condition is encountered the first time, the current value of MS_TIMER is saved and then on

each subsequent pass the saved value is compared to the current value. If a waitfor condition is not

encountered, then a jump is made to the end of the costatement (4), and on the next pass of the loop, when

the execution thread reaches the beginning of the costatement, execution passes directly to the waitfor

statement. Once 1000 ms has passed, the statement after the waitfor is executed. A costatement can

wait for a long period of time, but not use a lot of execution time. Each costatement is a little program with

its own statement pointer that advances in response to conditions. On each pass through the while loop

as few as one statement in the costatement executes, starting at the current position of the costatement’s

statement pointer. Consult Chapter 5 for more details.

The second costatement in the program checks to see if an alpha-numeric key has been pressed and, if one

has, prints out that key. The abort statement is illustrated at (5). If the abort statement is executed, the

internal statement pointer is set back to the first statement in the costatement, and a jump is made to the

closing brace of the costatement.

Observe the value of secs while the program is running.To illustrate the use of snooping, use the watch

window to observe secs while the program is running. Add the variable secs to the list of watch expres-

sions, then press <Ctrl+U> repeatedly to observe as secs increases.

3.4 Summary of Features

This chapter provided a quick look at the interface of Dynamic C and some of the powerful options avail-

able for embedded systems programming. The following several paragraphs are a summary of what we’ve

discussed.

Development Functions

When you load a program it appears in an editor window. You compile by clicking Compile on the task bar

or from the

Compile menu. The program is compiled into machine language and downloaded to the target

over the serial port. The execution proceeds to the first statement of main, where it pauses, waiting to run.

Press <F9> or select “Run” on the Run menu. If want to compile and run the program with one keystroke,

use <F9>, the run command; if the program is not already compiled, the run command compiles it.

Single Stepping

This is done with the F8 key. The F7 key can also be used for single stepping. If the F7 key is used, then

descent into functions will take place. With F8 the function is executed at full speed when the statement

that calls it is stepped over.

Dynamic C User’s Manual digi.com 18

Setting Breakpoints

The F2 key is used to toggle a breakpoint at the cursor position. Breakpoints can be toggled while in run

mode, either while stopped at a breakpoint or when the program is running at full speed. Breakpoints can

also be set in edit mode and retained when changing modes or closing the file.

Watch Expressions

A watch expression is a C expression that is evaluated on command in the Watches window. An expression

is basically any type of C statement that can include operators, variables, structures and function calls, but

not statements that require multiple lines such as for or switch. You can have a list of watch expres-

sions in the Watches window. If you are single stepping, then they are all evaluated on each step. You can

also command the watch expressions to be evaluated by using the <Ctrl+U> command. When a watch

expression is evaluated at a breakpoint, it is evaluated as if the statement was at the beginning of the func-

tion where you are single stepping.

Costatements

A costatement is a Dynamic C extension that allows cooperative multitasking to be programmed by the

user. Keywords, like abort and waitfor, are available to control multitasking operation from within

costatements.

Dynamic C User’s Manual digi.com 19

4. LANGUAGE

Dynamic C is based on the C language. The programmer is expected to know programming methodologies

and the basic principles of the C language. Dynamic C has its own set of libraries, which include user-call-

able functions. Please see the Dynamic C Function Reference Manual for detailed descriptions of these

API functions. Dynamic C libraries are in source code, allowing the creation of customized libraries.

Before starting on your application, read through the rest of this chapter to understand the differences

between standard C and Dynamic C.

For more information on the C language, see a reference book such as The C Programming Language

by

Kernighan and Ritchie (published by Prentice-Hall).

4.1 Storage Classes

Variable storage can be auto or static. The term “static” means the data occupies a permanent fixed

location for the life of the program. The term “auto” refers to variables that are placed on the system stack

for the life of a function call. The default storage class is auto, but can be changed by using

#class static; however, using this compiler directive with “static” is deprecated starting with

Dynamic C 10.44.

The default storage class can be superseded by the use of the keyword auto or static in a variable dec-

laration. These keywords apply to local variables, that is, variables defined within a function. If a variable

does not belong to a function, it is called a global variable—available anywhere in the program—but there

is no keyword in C to represent this fact. Global variables always have static storage.

The register type is reserved, but is not currently implemented. Dynamic C will change a variable to

be of type auto if register is encountered. Even though the register keyword is not implemented,

it still can not be used as a variable name or other symbol name. Its use will cause unhelpful error mes-

sages from the compiler.

4.2 Pointers

Pointer checking is a run-time option in Dynamic C. Use the Compiler tab on the Options | Project Options

menu. Pointer checking will catch attempts to dereference a pointer to unallocated memory. However, if an

uninitialized pointer happens to contain the address of a memory location that the compiler has already

allocated, pointer checking will not catch this logic error. Because pointer checking is a run-time option,

pointer checking adds instructions to code when pointer checking is used.

Pointer checking is not currently supported for far pointers.

Dynamic C User’s Manual digi.com 20

4.3 Far Pointers and Far Data

This section examines the syntax of the far keyword, using examples from simple variables to complex

aggregate types.

4.3.1 The far Qualifier

The far keyword allows a programmer to directly declare variables in xmem. Previous to this develop-

ment, usage of xmem was limited to library routines such as root2xmem() and xmem2root() using

memory allocated using xalloc. Now, the compiler will directly generate code to access xmem allocated

through standard variable declarations with the addition of the far keyword.

4.3.2 Basic Declarations

In almost all respects, far behaves syntactically identically to the const qualifier.

The keyword far was added to use the same basic principles as const, with a few exceptions. The rea-

son for this is that far and const both indicate the storage type for variables. In the case of const, the

storage is in the flash device. Variables declared as far are stored in xmem in RAM (and can therefore be

modified). A variable can also be declared as const far, which places the constant variable in the

xmem space on the flash device.

far type var; // Declares a variable “var” having far storage

We also allow

type far var;

which has the same meaning as the previous declaration. In other words, the far keyword may appear

before or after the base type.

We do not allow

far type far var;

In this context, these are base type qualifiers. The far keyword can also qualify pointer types, such as in

the following example:

type * far ptr;

This declares a variable, ptr, having far storage pointing to an object of type type. Pointer qualifiers are

always found on the right-hand side of the ‘*’ token.

Here is a slightly more complex declaration:

far type * far ptr;

Here, the object type to which ptr points is qualified as having far storage.

Page is loading ...

Digi RCM6600W User manual

Digi RCM6600W User manual

Related papers

Other documents