COMPACT COMPONENT SYSTEM
FS-SD58V/FS-SD78V/FS-SD98V
Consists of CA-SD58V and SP-SD58V
Consists of CA-SD78V and SP-SD78V
Consists of CA-SD98V and SP-SD98V
NTSC / PAL COMPATIBILITY
REMOTE CONTROL
DIMMER SLEEP
DISPLAY DOOR SLIDE
PLAY MODE REPEAT CANCEL
AHB PRO
TONE
CONTROL
CLOCK
/
TIMER
HIGHLIGHT
PBC ON
/
OFF
VCD NUMBER
SELECT
NEXTPREV
VCD NUMBER
VIDEO INTRO STILL
UP
SET
DOWN
MD
/
AUX
FM
/
AM
VOLUME
CD
FADE MUTING
ON SCREEN
FM MODE
MPX
NTSC / PAL COMPATIBILITY
CA-SD58V
CA-SD78V, CA-SD98V
REMOTE CONTROL
DIMMER SLEEP
DISPLAY DOOR SLIDE
PLAY MODE REPEAT CANCEL
AHB PRO
TONE
CONTROL
CLOCK
/
TIMER
HIGHLIGHT
PBC ON
/
OFF
VCD NUMBER
SELECT
NEXTPREV
VCD NUMBER
VIDEO INTRO STILL
UP
SET
DOWN
MD
/
AUX
FM
/
AM
VOLUME
CD
FADE MUTING
ON SCREEN
FM MODE
MPX
SP-SD58VSP-SD58V
SP-SD78V, SD98V SP-SD78V, SD98V
For Customer Use:
Enter below the Model No. and Serial No.
which are located either on the rear, bot-
tom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
INSTRUCTIONS
LVT0548-001A
[US/UB]
FS-SD58V_Cover1.fm Page 1 Thursday, September 28, 2000 4:47 PM
G-1
Warnings, Cautions and Others
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Caution –– switch!
Disconnect the mains plug to shut the power off completely.
The switch in any position does not disconnect the mains
line. The power can be remote controlled.
IMPORTANT FOR LASER PRODUCTS /
REPRODUCTION OF LABELS /
1 CLASSIFICATION LABEL, PLACED ON EXTERIOR SUR-
FACE
1
2 WARNING LABEL, PLACED INSIDE THE UNIT
2
1. CLASS 1 LASER PRODUCT
2.
DANGER:
Invisible laser radiation when open and interlock
failed or defeated. Avoid direct exposure to beam.
3.
CAUTION:
Do not open the top cover. There are no user
serviceable parts inside the Unit; leave all servicing to
qualified service personnel.
CLASS 1
LASER PRODUCT
FS-SD58V_Warning.fm Page 1 Thursday, September 28, 2000 4:48 PM
G-2
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1 Front: No obstructions and open spacing.
2 Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.
3 Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of
10 cm or more.
NTSC / PAL COMPATIBILITY
15 cm
15 cm
Front view
Side view
CAUTION
❏
❏❏
❏
About the Internal Cooling Fan
This unit includes an internal cooling fan, so as to allow for high-
power operation within a small space.
This fan comes on when the sound level is set high, and may also
come on even at low sound levels if the internal temperature rises. To
ensure effective fan operation, please leave at least 15cm clearance
between the rear of the unit and the wall, and at least 1cm clearance
on each side of the unit.
FS-SD58V_Warning.fm Page 2 Thursday, September 28, 2000 4:48 PM
1
English
Introduction
Thank you for purchasing the JVC Compact Component System.
We hope it will be a valued addition to your home, giving you years of enjoyment.
Be sure to read this instruction manual carefully before operating your new stereo system.
In it you will find all the information you need to set up and use the system.
If you have a query that is not answered by the manual, please contact your dealer.
Features
Here are some of the things that make your System both powerful and simple to use.
❏ Types of CD you can play
Many types of compact discs are sold for a variety of uses. The Video CD Player can play the following compact discs.
• Video CD without Playback Control function: for audio and video (moving picture) reproduction.
• Video CD with Playback Control function: featuring menu-type operation and super-fine still pictures for audio
and video (moving picture) reproduction.
• CD Graphics (CD-G): for audio and video (still picture) reproduction.
• Digital Audio CD, including 8-cm(3")CDs: for audio reproduction.
• CDs you cannot play: Do not play SVCDs, DVDs and CD-ROMs on this System. Playing CD-ROMs may generate
a noise which can damage your speakers.
❏ JVC’s COMPU PLAY feature that, with a single touch, automatically starts playing the Radio or CD
Player.
❏ The System incorporates Active Hyper Bass PRO circuitry to faithfully reproduce low frequency
sounds.
❏ A 45-station preset capability (30 FM and 15 AM ) in addition to auto-seek and manual tuning.
❏ CD options that include repeat, random and program play.
❏ Timer functions; Daily Timer and Sleep Timer.
❏ You can connect various external units, such as an MD recorder.
How This Manual Is Organized
• Basic information that is the same for many different functions - e.g. setting the volume - is given in the section
‘Basic Operations’, and not repeated under each function.
• The names of buttons/controls and display messages are written in all capital letters: e.g. FM/AM, “NO DISC”.
• System functions are written with an initial capital letter only: e.g. Normal Play.
Use the table of contents to look up specific information you require.
We have enjoyed making this manual for you, and hope it serves you in enjoying the many features built into your System.
WARNINGS
• DO NOT PUT ANYTHING ON THE TOP COVER. IF THE SYSTEM IS OPERATED WITH SOMETHING
PUT ON THE TOP COVER, IT WILL BE DAMAGED WHEN YOU TRY TO OPEN THE TOP COVER.
• NEVER REMOVE THE TOP COVER FROM THE UNIT. SERIOUS INJURY MAY OCCUR IF THE SYS-
TEM IS OPERATED WITHOUT THE TOP COVER.
IMPORTANT CAUTIONS
1
Installation of the System
• Select a place which is level, dry and neither too hot nor too cold. (Between 5°C and 35°C or 41°F and 95°F.)
• Leave sufficient distance between the System and a TV.
• Do not use the System in a place subject to vibrations.
2
Power cord
• Do not handle the power cord with wet hands!
• Some power is always consumed as long as the power cord is connected to the wall outlet.
• When unplugging the System from the wall outlet, always pull the plug, not the power cord.
3
Malfunctions, etc.
• There are no user serviceable parts inside. In case of system failure, unplug the power cord and consult your dealer.
• Do not insert any metallic object into the System.
• Do not insert your hand between the Top Cover and the main body when the Top Cover is being closed.
FS-SD58V_Intro.fm Page 1 Thursday, September 28, 2000 4:48 PM
Table of Contents
2
English
Introduction.....................................................................................................................................1
Features............................................................................................................................................................................ 1
How This Manual Is Organized....................................................................................................................................... 1
WARNINGS.................................................................................................................................................................... 1
IMPORTANT CAUTIONS............................................................................................................................................. 1
Getting Started................................................................................................................................3
Accessories...................................................................................................................................................................... 3
Set the VOLTAGE SELECTOR Switch......................................................................................................................... 3
How To Put Batteries In the Remote Control.................................................................................................................. 3
Using the Remote Control............................................................................................................................................... 3
Connecting the FM Antenna............................................................................................................................................ 4
Connecting the AM Antenna........................................................................................................................................... 5
Connecting the Speakers ................................................................................................................................................. 6
Attaching the Spacers...................................................................................................................................................... 7
Connecting a TV.............................................................................................................................................................. 7
Connecting External Equipment...................................................................................................................................... 7
Connecting an MD Recorder, etc (Digital Output) ......................................................................................................... 7
Connecting the AC Power Cord ...................................................................................................................................... 8
COMPU Play................................................................................................................................................................... 8
Automatic Power On ....................................................................................................................................................... 8
Basic Operations............................................................................................................................9
Turning the Power On and Off................................................................................................................... 9
Adjusting the Brightness (DIMMER)......................................................................................................... 9
Adjusting the Volume................................................................................................................................. 9
Fade-out Muting (FADE MUTING) ........................................................................................................ 10
Reinforcing the Bass Sound (AHB PRO)................................................................................................. 10
Tone Control (TONE CONTROL)........................................................................................................... 10
Showing the Time (DISPLAY) ................................................................................................................ 10
Sliding the Top Cover (DOOR SLIDE) ................................................................................................... 10
Using the Tuner............................................................................................................................11
Tuning In a Station ................................................................................................................................... 11
Presetting Stations..................................................................................................................................... 12
Auto Presetting ......................................................................................................................................... 12
To Change the FM Reception Mode........................................................................................................ 12
Using the CD Player.....................................................................................................................13
To Insert a CD........................................................................................................................................... 13
To Unload a CD........................................................................................................................................ 14
Basics of Using the CD Player-Normal Play............................................................................................ 14
Programming the Playing Order of the Tracks......................................................................................... 14
Random Play............................................................................................................................................. 15
Repeating Tracks ...................................................................................................................................... 15
Using the Video CD Player (Video CDs, CD-Gs)........................................................................16
Setting the TV System.............................................................................................................................. 16
Selecting the Audio Channel .................................................................................................................... 16
Playing Video CDs with PBC Function ................................................................................................... 17
Playing Video CDs with PBC Functions without Using the Menu Screen (PBC OFF) .......................... 18
Playing video CDs without the PBC Function......................................................................................... 18
Playing CD-Gs.......................................................................................................................................... 18
Various Functions to Enhance Your Enjoyment ...................................................................................... 19
Using External Equipments.........................................................................................................20
Listening to External Equipment.............................................................................................................. 20
Recording the System’s Source to External Equipment........................................................................... 20
Using the Timers ..........................................................................................................................21
Setting the Clock....................................................................................................................................... 21
Setting the Daily Timer............................................................................................................................. 21
Setting the SLEEP Timer.......................................................................................................................... 23
Care And Maintenance.................................................................................................................24
Troubleshooting...........................................................................................................................25
Specifications...............................................................................................................................26
FS-SD58V_TOC.fm Page 2 Thursday, September 28, 2000 4:49 PM
3
English
Getting Started
Accessories
Make sure that you have all of the following items, which are supplied with the System.
Power Cord (1)
AM Loop Antenna (1)
Remote Control (1)
Batteries (2)
FM Wire Antenna (1)
Speaker Cords (2)
Video Cord (1)
Spacers (6) (only for SP-SD78V / SD98V)
AC Plug Adaptor (except for Hong Kong)
If any of these items are missing, contact your dealer immediately.
Set the VOLTAGE SELECTOR Switch
To avoid damaging the System, set the voltage before plugging in the System.
Set the correct voltage for your area with the VOLTAGE SELECTOR switch on the back of the Unit. By using a screwdriver,
rotate the VOLTAGE SELECTOR switch so that the arrow mark points the voltage of your area.
How To Put Batteries In the Remote Control
Match the polarity (+ and –) on the batteries with the + and – markings in the battery compartment.
CAUTION:
• Handle batteries properly.
❏ To avoid battery leakage or explosion:
• Remove batteries when the Remote Control will not be used for a long time.
• When you need to replace the batteries, replace both batteries at the same time with new ones.
• Do not use an old battery with a new one.
• Do not use different types of batteries together.
Using the Remote Control
The Remote Control makes it easy to use many of the functions of the System from a distance of up to 7m (23 feet) away.
You need to point the Remote Control at the remote sensor on the System’s front panel.
R6P(SUM-3)/AA(15F)
Remote sensor
STANDBY/ON
NTSC / PAL COMPATIBILITY
OPEN/CLOSE
PHONES
FS-SD58V_A1.fm Page 3 Thursday, September 28, 2000 4:49 PM
4
Getting Started
English
CAUTION:
• Make all connections before plugging the System into an AC power outlet.
Connecting the FM Antenna
Rear Panel of the Unit
Using the Supplied Wire Antenna
Using the Coaxial Type Connector
(Not Supplied)
A 75-ohm antenna with coaxial type connector (IEC or
DIN45 325) should be connected to the FM 75-ohm CO-
AXIAL terminal.
If reception is poor, connect the outdoor antenna.
• Before attaching a 75 ohm coaxial lead (the kind with a
round wire going to an outdoor antenna), disconnect the
supplied FM Wire Antenna.
VIDEO OUT
CD DIGITAL OUT
ANTENNA
AM EXT FM
(
75
)
COAXIAL
AM LOOP
OUT IN
MD
/
AUX
SPEAKERS IMPEDANCE 4 16
R
AC IN
L
FM wire antenna (supplied)
Coaxial cable
FM outdoor
antenna
(Not supplied)
FS-SD58V_A1.fm Page 4 Thursday, September 28, 2000 4:49 PM
5
Getting Started
English
Connecting the AM Antenna
Rear Panel of the Unit
• If the AM loop antenna wire is covered with vinyl, remove the vinyl by twisting it as shown in the diagram.
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord.
This could cause poor reception.
• If reception is poor, connect an outdoor single vinyl-covered wire to the AM EXT terminal. (Keep the AM loop
antenna connected.)
VIDEO OUT
CD DIGITAL OUT
ANTENNA
AM EXT FM
(
75
)
COAXIAL
AM LOOP
OUT IN
MD
/
AUX
SPEAKERS IMPEDANCE 4 16
R
AC IN
L
Attach the AM loop to its base by snapping the tabs on
the loop into the slot in the base.
AM loop antenna (Supplied)
ANTENNA
AM EXT FM
(
75
)
COAXIAL
AM LOOP
Turn the loop until you have the best reception.
Outdoor single
vinyl-covered wire
FS-SD58V_A1.fm Page 5 Thursday, September 28, 2000 4:49 PM
6
Getting Started
English
CAUTION:
• Make all connections before plugging the System into an AC power outlet.
Connecting the Speakers
1. Open each of the terminals to connect the speaker wire leads.
2. Connect the speaker cords between the Speaker terminals of the Unit and the terminals of the Speakers.
Connect the cords with a black line to the (–) terminals and cords without a black line to the (+) terminals.
3. Close each of the terminals to securely connect the cords.
• Since both speakers are the same, you can put either one to the right or left side.
Removing the speaker grilles
The speaker grilles can be removed.
When removing:
1. Pull the top forwards you with your fingers.
2. Also pull the bottom towards you.
• When removing the speaker grille from the SP-SD98V’s
speaker, be careful not to damage the cabinet.
When attaching the speaker grille:
SPEAKERS IMPEDANCE 4 16
RL
Marked with a black line
Right side (rear view)
Left side (rear view)
Speaker
grille
(SP-SD58V)
(SP-SD78V and SP-SD98V)
Speaker
grille
(SP-SD58V)
(SP-SD78V and SP-SD98V)
FS-SD58V_A1.fm Page 6 Thursday, September 28, 2000 4:49 PM
7
Getting Started
English
Attaching the Spacers
CAUTION:
N
NN
No
oo
ot
tt
te
e e
e f
ff
fo
oo
or
r r
r i
ii
in
nn
ns
ss
st
tt
ta
aa
al
ll
ll
ll
la
aa
at
tt
ti
ii
io
oo
on
nn
n
• Take special care to select an appropriate installa-
tion place where an earthquake or shock does not
cause the speaker to collapse or drop on the floor.
SP-SD78V / SD98V
Attach the supplied spacers to the bottom of the speaker to
protect the cabinet, prevent slipping, and absorb the cabinet
vibration. Peel off the backing from a spacer and attach it.
Connecting a TV
Connect a video cord (supplied) between the System’s VIDEO OUT terminal and the video input jack of your TV.
• Do not connect a cable between the MD/AUX-OUT terminal and the audio input terminal of an external TV. If it is connected,
noise may be generated depending on the TV to be used.
Connecting External Equipment
Connect signal cords (not supplied) between the System’s MD/AUX-OUT/IN terminals and the output/input terminals of the
external MD recorder, tape deck, etc.
You can then listen to the external source through the System or record the System’s CD player or tuner to the external unit.
Connecting an MD Recorder, etc (Digital Output)
Unplug the cap and connect an optical digital cord (not supplied) between the System’s CD DIGITAL OUT terminal and the
input terminal of the MD recorder, etc.
You can record the digital output signal from the System’s CD Player to the MD recorder, etc.
(SP-SD78V)
(SP-SD98V)
Spacer
Spacer
*
VIDEO OUT
CD DIGITAL OUT
ANTENNA
AM EXT FM
(
75
)
COAXIAL
AM LOOP
OUT IN
MD
/
AUX
* Use the plug whose diameter is 11mm or less.
11mm Max.
Video cord
Pin-plug
TV (not supplied)
VIDEO OUT
CD DIGITAL OUT
ANTENNA
AM EXT FM
(
75
)
COAXIAL
AM LOOP
OUT IN
MD
/
AUX
*
*
Signal cord (not supplied)
MD recorder or tape deck
(not supplied)
Pin-plug x 2
Pin-plug x 2
Signal cord (not supplied)
Stereo mini-plug
Stereo mini-plug
* Use the plug whose diameter is 11mm or less.
11mm Max.
11mm Max.
CD DIGITAL OUT
*
MD recorder, etc. (not supplied)
Optical digital cord (not supplied)
Cap
* Use the plug whose diameter is
11mm or less.
11mm Max.
FS-SD58V_A1.fm Page 7 Thursday, September 28, 2000 4:49 PM
8
Getting Started
English
Connecting the AC Power Cord
Firmly insert the supplied AC power cord into the AC inlet on the back of the Unit.
CAUTIONS:
• ONLY USE THE JVC POWER CORD PROVIDED WITH THIS SYSTEM TO AVOID MALFUNC-
TION OR DAMAGE TO THE SYSTEM.
• BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN GOING OUT OR WHEN
THE SYSTEM IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.
Now you can plug the AC power cord into the wall outlet, and your System is at your command!
COMPU Play
JVC’s COMPU PLAY feature lets you control the most frequently used System functions with a single touch.
With One Touch Operation you can play a CD, turn on the radio, or listen to an external equipment with a single press of the
play button for that function. One Touch Operation turns the power on for you, then starts the function you have specified. At
the same time, the Top Cover moves backward to allow the Unit’s top button operation. If the System is not ready (no CD in
place), the System still powers on so you can insert a CD.
How One Touch Operation works in each case is explained in the section dealing with that function.
The COMPU PLAY buttons are:
Automatic Power On
The System automatically turns on with the following operation.
• When you press the OPEN/CLOSE button on the Unit, the System automatically turns on and the Top Cover opens to allow
CD setting. However, this operation does not change the function to CD.
When you press the % button to turn off the System, the Top Cover will be automatically closed if it is opened.
• When you press the DOOR SLIDE button on the Remote Control, the System automatically turns on and the Top Cover
moves backwards to allow button operation.
When you press the % button to turn off the System, the Top Cover will automatically moves back to the original position,
if it is in the backward position.
On the Remote Control
CD #/8 button
FM/AM button
MD/AUX button
AC IN
Power cord
FS-SD58V_A1.fm Page 8 Thursday, September 28, 2000 4:49 PM
9
English
Basic Operations
Turning the Power On and Off
Turning the System On
Press the % button.
The Top Cover moves backward and the Unit’s top buttons
appear. The display comes on and “HELLO” is displayed
once. The STANDBY/ON indicator lights in green.
The System comes on ready to continue in the mode it was
in when the power was last turned off.
❏For example, if the last thing you were doing was listen-
ing to a CD, you are now ready to listen to a CD again. If
you wish, you can change to another source.
❏If you were listening to the Tuner last, the Tuner comes
on playing the station it was last set to.
Turning the System Off
Press the % button again.
The Top Cover moves back to the original position.
“GOOD BYE” is displayed and the display goes out, except
for the clock display. The STANDBY/ON indicator lights in
red.
❏Some power is always consumed even though power is
turned off (called Standby Mode).
❏To switch off the System completely, unplug the AC
power cord from the wall outlet. When you unplug the
AC power cord, the clock will be reset to 0:00 after about
20 minutes.
Adjusting the Brightness
(DIMMER)
You can adjust the brightness of the backlighting for the dis-
play.
When the System is Turned On
Each time you press the DIMMER button on the Remote
Control, the brightness of the backlighting changes as fol-
lows:
Bright = Dark = (back to the beginning)
When the System is Turned Off
(STANDBY MODE)
Each time you press the DIMMER button on the Remote
Control, the brightness of the backlighting changes as fol-
lows:
No backlighting = Dark backlighting
= (back to the beginning)
• When the System is turned off again after power on, the
brightness in Standby mode will be restored to the previ-
ous one since the brightness setting in Standby mode is
stored in memory.
Adjusting the Volume
Press the VOLUME + button to increase the volume or
press the VOLUME – button to decrease it.
You can adjust the volume level between 0 and 50.
CAUTION:
• DO NOT turn off the System with the vol-
ume set to an extremely high level; other-
wise a sudden blast of sound could
damage your hearing, speakers and/or
headphones when you turn on the System
or start playing any source next time.
REMEMBER you cannot adjust the volume
level while the System is in standby mode.
For private listening
Connect a pair of headphones to the PHONES jack. No
sound comes out of the speakers.
Be sure to turn down the volume before connecting or put-
ting on headphones.
CD
STANDBY/ON
NTSC / PAL COMPATIBILITY
OPEN/CLOSE
PHONES
DIMMER
AHB PRO
VOLUME+,–
VOLUME+,–
DOOR SLIDE
%
FADE
MUTING
DISPLAY
STANDBY/ON indicator
PHONES
%
Top Cover
TONE CONTROL
REMOTE CONTROL
VOLUME
FM MODE
MPX
DIMMER SLEEP
DISPLAY DOOR SLIDE
PLAY MODE REPEAT CANCEL
AHB PRO
TONE
CONTROL
CLOCK
/ TIMER
HIGHLIGHT
PBC ON / OFF
VCD NUMBER
SELECT
NEXTPREV
VCD NUMBER
VIDEO INTRO STILL
UP
SET
DOWN
MD
/
AUX FM
/
AM
CD
FADE MUTING
ON SCREEN
FS-SD58V_A1.fm Page 9 Thursday, September 28, 2000 4:49 PM
10
Basic Operations
English
Fade-out Muting (FADE MUTING)
You can mute the audio output with one touch operation.
To mute the audio output, press the FADE MUTING
button on the Remote Control. Then, the audio output will
be faded out and becomes 0 (VOLUME 0).
To release muting, press the FADE MUTING button
once again. Then, the audio output will be faded in to the
original level.
• The signal output from the MD/AUX-OUT is not muted.
Reinforcing the Bass Sound
(AHB PRO)
You can reinforce the bass sound to maintain rich, full bass
at low volume.
To get the effect, press the AHB (Active Hyper Bass)
PRO button on the Remote Control.
The “AHB PRO” indicator lights up on the display.
To cancel the effect, press the same button again.
The “AHB PRO” indicator goes out.
Tone Control (TONE CONTROL)
You can control the tone by changing the bass (low frequen-
cy range level) and treble (high frequency range level).
1
Press the TONE CONTROL button on
the Remote Control to select "BASS"
or "TREBLE".
Each time you press the button, the display will change
as follows:
BASS --> TREBLE --> (original display) --> (back to
the beginning)
2
Press the UP or DOWN button on the
Remote Control to adjust the bass or
treble level.
You can adjust each level between -5 and +5. (0: Flat)
Showing the Time (DISPLAY)
You can show the current time on the display.
To display the clock, press the DISPLAY button on the
Remote Control.
To return to the previous mode, press the same button
again.
• To let the clock work, you need to set the clock first. (See
“Setting the Clock” on page 21.)
Sliding the Top Cover
(DOOR SLIDE)
Each time you press the DOOR SLIDE button on the Re-
mote Control, the Top Cover slides back and forth.
Slide the Top Cover backward to allow Unit’s top button
operation. Slide it toward you to cover the buttons.
DOWN
UP
TONE
CONTROL
(
BASS or TREBLE
)
FS-SD58V_A1.fm Page 10 Thursday, September 28, 2000 4:49 PM
11
English
Using the Tuner
You can listen to FM and AM stations. Stations can be tuned
in manually, automatically, or from preset memory storage.
❏Before listening to the radio:
• Make sure that both the FM and AM antennas are cor-
rectly connected. (See pages 4 and 5).
Setting the AM Tuner Interval Spacing
When shipped, the AM tuner interval is set to 9 kHz spacing.
You can change it to 10 kHz spacing.
●Preparation to setting:
Turn on the power and press the FM/AM button to select
AM mode.
To select 10 kHz intervals, while holding down the 7
button on the Unit, press the VOLUME + button on the
Unit. “AM 10 kHz” will appear on the display (at the same
time, the 100 kHz spacing is selected for FM broadcast).
To select 9 kHz intervals, while holding down the 7 but-
ton on the Unit, press the VOLUME − button on the Unit.
“AM 9kHz” will appear on the display.
[10 kHz Intervals] [9 kHz Intervals]
• When you change the setting, the preset stations are
erased. You will need to preset the stations again. (See
page 12.)
One Touch Radio
Just press the FM/AM button to turn on the System and start
playing the station you were last tuned to.
❏You can switch from any other sound source to the radio
by pressing the FM/AM button.
Tuning In a Station
1
Press the FM/AM button.
The Band and Frequency you were last tuned to appear
on the display.
(If the last station was selected using the preset number,
the preset number appears first.)
Each time you press the button, the band alternates be-
tween FM and AM.
2
Select a station using one of the follow-
ing methods.
●Manual Tuning
Press the 4 or ¢ (DOWN or UP) button on the
Unit or the Remote Control repeatedly to move from
frequency to frequency until you find the station you
want.
OR
●Auto Tuning
If you press and hold the 4 or ¢ (DOWN or UP)
button on the Unit or the Remote Control for one sec-
ond or more, the frequency changes down, or up, au-
tomatically until a station is found.
OR
●Preset Tuning using the Remote Control
(Possible only after presetting stations)
Select the desired preset number using the > and < but-
ton on the Remote Control. After 1 second the display
will show the preset number’s band and frequency.
Example:
Press the > button until the preset number 12 “P12”
appears. (Each time you press the > button, the preset
number will be increased by 1.)
REMOTE CONTROL
VOLUME
FM MODE
MPX
DIMMER SLEEP
DISPLAY DOOR SLIDE
PLAY MODE REPEAT CANCEL
AHB PRO
TONE
CONTROL
CLOCK
/ TIMER
HIGHLIGHT
PBC ON / OFF
VCD NUMBER
SELECT
NEXTPREV
VCD NUMBER
VIDEO INTRO STILL
UP
SET
DOWN
MD
/
AUX FM
/
AM
CD
FADE MUTING
ON SCREEN
STEREO
MONO
FM MODE
DOWN
¢
4
UP
FM/AM
Band display, Frequency display, Preset channel
FM mode
indicators
FM/AM
4
* When the System is in use, the display shows other items as well.
For simplicity, we show here only the items described in this section.
¢
SET
PRESET
TUNING +, −
7
VOLUME +, −
><
VOLUME
VOLUME
FM
/
AM
FMAM
FM/AM
FMAM
(on the Remote Control)
(on the Unit)
(After 1 second)
or
FS-SD58V_A1.fm Page 11 Thursday, September 28, 2000 4:49 PM
12
Using the Tuner
English
●Preset Tuning using the Unit
Press the PRESET TUNING + or - button to select
the desired preset number.
Its band and frequency are displayed.
• In AM broadcast, reception sensitivity will be changed by
turning the AM loop antenna. Turn the AM loop antenna
for best reception.
Presetting Stations
You can preset up to 30 FM stations and up to 15 AM sta-
tions using the Remote Control.
• Preset numbers may have been set to factory test fre-
quencies prior to shipment. This is not a malfunction. You
can preset the stations you want into memory by following
one of the presetting methods below.
Manual Presetting
1
Select a band by pressing the FM/AM
button.
2
Press the 4 or ¢ (DOWN or UP) but-
ton on the Unit or the Remote Control to
tune in a station.
3
Press the SET button.
“SET” will blink for 5 seconds.
Within 5 seconds, proceed to the next step.
When the display returns to the one set in step 2 after 5
seconds, press the SET button again.
4
Press the > or < button within 5 seconds
to select the preset number.
Pressing the > or < button will increase or decrease the
preset number by 1.
Pressing and holding the button will rapidly increase or
decrease the preset number.
5
Press the SET button within 5 seconds.
“STORED” appears and after 2 seconds, the display re-
turns to the broadcast frequency display.
6
Repeat above steps 1 to 5 for each sta-
tion you want to store in memory with a
preset number.
To change the preset stations, repeat the same
steps as above.
Auto Presetting
In each band, you can automatically preset FM-30, AM-15
stations. Preset numbers will be allocated as stations are
found, starting from the lowest frequency and moving up
the frequency.
1
Select a band by pressing the FM/AM
button.
2
Press the SET button on the Remote
Control for more than two seconds.
3
Repeat steps 1-2 for the other band.
❏If you want to change the preset stations, carry out the
Manual Presetting for the desired preset numbers.
CAUTION:
• Even if the system is unplugged or if the
power failure occurs, the preset stations
will be stored for about 24 hours. However,
in case the preset stations are erased, you
will need to preset the stations again.
To Change the FM
Reception Mode
When you are tuned into an FM stereo broadcast, the
“STEREO” indicator lights up and you can hear stereo ef-
fects.
If an FM stereo broadcast is hard to receive or noisy, you
can select Monaural mode. Reception improves, but you
lose stereo effect.
Press the FM MODE button on the Remote Control
so that the “MONO” indicator lights up on the dis-
play.
To restore the stereo effect, press the FM MODE but-
ton on the Remote Control so that the “MONO” indicator
goes off.
FM
/
AM
SET
SET STORED
SET
When changing the Band
FM = 30, AM = 15
or
FM
/
AM
SET
(for 2 seconds)
MONO
FM MODE
MPX
FS-SD58V_A1.fm Page 12 Thursday, September 28, 2000 4:49 PM
13
English
Using the CD Player
You can use Normal, Random, Program or Repeat Play. Re-
peat Play can repeat all the tracks or just one of the tracks
on the CD.
Here are the basic things you need to know to play a CD and
locate the different tracks on it.
The Quickest Way To Start a CD Is With the One
Touch Operation
❏Press the CD #¥8 button on the Remote Control.
• The power is automatically turned on and the Top Cover
moves backward to allow the Unit’s top button opera-
tion. If a CD is already inserted, it will start playing from
the first track.
• If no CD is inserted, “NO DISC” appears on the display
and the CD Player remains in Stop mode.
To Insert a CD
1
Press the OPEN/CLOSE button on the
Unit.
The Top Cover opens.
2
Place a CD, with its label side up as
shown below. Press down on the CD’s
center until you hear a click.
3
Press the OPEN/CLOSE button again to
close the Top Cover.
• To close the Top Cover and play the CD, you can just
press the CD #¥8 button.
❏You can place an 8 cm (3'') CD without an adaptor.
❏If the CD cannot be read correctly (because it is
scratched, for example), “ 0 0:00” appears on the display.
❏You can insert a CD while listening to the other source.
CAUTION:
• DO NOT try to open or close the Top Cover
by hands as it will be damaged.
PROGRAM
RANDOM ALL
2019181716151413121110
987654321
STANDBY/ON
NTSC / PAL COMPATIBILITY
OPEN/CLOSE
PHONES
Music calendar
Repeat indicators
Track number, Playing time, Preset number
SET
<
PLAY MODE
UP
>
DOWN
CD #/8
7
4
¢
* When the System is in use, the display shows other items as well.
For simplicity, we show here only the items described in this section.
4
7
CD #¥8
¢
Top Cover
OPEN/CLOSE
Track number exceeding 20 is not
displayed.
CANCEL
REMOTE CONTROL
VOLUME
FM MODE
MPX
DIMMER SLEEP
DISPLAY DOOR SLIDE
PLAY MODE REPEAT CANCEL
AHB PRO
TONE
CONTROL
CLOCK
/ TIMER
HIGHLIGHT
PBC ON / OFF
VCD NUMBER
SELECT
NEXTPREV
VCD NUMBER
VIDEO INTRO STILL
UP
SET
DOWN
MD
/
AUX FM
/
AM
CD
FADE MUTING
ON SCREEN
Play mode indicators
NTSC / PAL COMPATIBILITY
FS-SD58V_A2.fm Page 13 Thursday, September 28, 2000 4:50 PM
14
Using the CD Player
English
To Unload a CD
Take out the CD as shown below.
Basics of Using the
CD Player-Normal Play
To Play a CD
• The display explained here is for digital audio CDs. It
differs a little depending on the disc to be used. For
example, when a video CD is played, “VCD” will be dis-
played instead of “CD”.
1
Insert a CD.
2
Press the CD #¥8 button.
The first track of the CD begins playing.
• The track number that has already played disappears
from the music calendar.
• The CD Player automatically stops when the last
track of the CD has finished playing.
To stop playing the CD, press the 7 button.
The following information for the CD is displayed.
To stop playing and remove the CD, press the
OPEN/CLOSE button on the Unit to open the Top Cover.
To pause, press the CD #¥8 button. The playback time
blinks on the display.
To cancel pause, press the same button again. Play con-
tinues from the point where it was paused.
To Select a Track or Passage within a Track
During playback, press the 4 or ¢ (DOWN or UP, or
< or >) button on the Unit or the Remote Control to select
the track you want.
• The selected track starts playing.
• Press the ¢ (UP or >) button on the Unit or the
Remote Control once to skip to the beginning of the
next track.
• Press the 4 (DOWN or <) button on the Unit or the
Remote Control to skip to the beginning of the track
being played. Press twice quickly to skip to the begin-
ning of the previous track.
• When the > or < button on the Remote Control is
kept pressing, the track continuously skips.
Search Play
Holding down the 4 or ¢ (DOWN or UP) button on
the Unit or the Remote Control, during playback, will fast
forward/backwards the CD so you can quickly find a partic-
ular passage in the track you are listening to.
Programming the
Playing Order of the Tracks
You can program the playing order of the tracks using the
Remote Control.
❏You can program up to 32 tracks in any desired order in-
cluding the same tracks.
❏You can only make a program when the CD Player is
stopped.
1
Insert a CD.
2
Press the CD #/8 button.
3
Press the 7 button to stop the CD.
4
Press the PLAY MODE button until the
"PROGRAM" indicator lights up on the
display.
Each time you press the PLAY MODE button, the dis-
play changes as follows:
CD - - P - - (Program Play) --> CD RANDOM (Ran-
dom Play) --> Normal Play --> (back to the beginning)
5
Press the UP, DOWN, >, or < button to
select the track to program.
UP or > button: Increases the track number by 1.
DOWN or < button:Decreases the track number by 1.
• When the > or < button is kept pressing, the track
number changes rapidly.
NTSC / PAL COMPATIBILITY
Track number Playback time
Total track number Total playback time
PLAY MODE
PROGRAM
(To be continued on the next page)
FS-SD58V_A2.fm Page 14 Thursday, September 28, 2000 4:50 PM
15
Using the CD Player
English
6
Press the SET button.
7
Repeat steps 5 and 6 to select the other
tracks for the program.
You can see the total playback time of programmed
tracks on the display. Also, you can see the programmed
tracks on the music calendar.
8
Press the CD
#
/
8
button.
The System plays the tracks in the order you have pro-
grammed them.
❏You can skip to a particular program track by pressing the
4 or ¢ button during Program Play.
❏To stop playing, press the 7 button once.
To confirm the programmed tracks while the CD
player is stopped, each time press the 4 or ¢ but-
ton; the tracks making up the program will successively be
displayed in the programmed order.
To delete all the tracks in the program, in stop mode,
press the 7 button for more than two seconds. Pressing the
OPEN/CLOSE button on the unit to open the Top Cover
will also clear the programmed tracks.
To exit the program mode, while the CD Player is
stopped, press the PLAY MODE button to light off the
“PROGRAM” indicator, or press the OPEN/CLOSE button
on the Unit to open the Top Cover.
• If the total playback time of the programmed tracks ex-
ceeds 99 minutes 59 seconds, the total playback time will
go out and “ ” appears on the display.
• If you try to program the 33rd track, “MEMORY FULL” ap-
pears on the display for about 2 seconds.
To Modify the Program
Modify the contents of the program while the CD Player is
stopped.
Each time you press the CANCEL button, the last track in
the program is deleted. To add new tracks to the end of the
program, repeat above steps 5 to 7.
Random Play
The tracks will play in no special order when you use this
mode.
(Using the Remote Control)
1
Insert a CD.
2
Press the CD
#
/
8
button to set the CD
mode.
3
Press the button to stop the CD.
4
Press the PLAY MODE button until the
“RANDOM” indicator lights up on the
display.
Each time you press the PLAY MODE button, the dis-
play changes as follows:
CD - - P - - (Program Play) --> CD RANDOM (Ran-
dom Play) --> Normal Play --> (back to the beginning)
5
Press the CD
#
/
8
button.
The tracks are played in random order.
To skip a track during playback, press the ¢ button
to jump to the next track in the random sequence. Press the
4 button to jump back to the start of a track being played.
To exit Random Play mode, while the CD Player is
stopped, press the PLAY MODE button to light off the “RAN-
DOM” indicator, or press the OPEN/CLOSE button on the
Unit to open the Top Cover.
Repeating Tracks
You can repeat all tracks or individual track, as many times
as you like.
Press the REPEAT button on the Remote Control.
The Repeat indicator changes with each press of the button,
as shown below.
= ALL=blank display = (back to the
beginning)
: Repeats one track.
ALL: In Normal Play mode, repeats all the tracks.
In Program Play mode, repeats all the tracks
in the program.
In Random Play mode, repeats all the tracks
in random order.
To exit Repeat mode, press the REPEAT button until the
Repeat indicator on the display goes out.
❏In Random Play, cannot be selected.
❏Repeat mode will remain in effect even when you change
the play mode.
UP
DOWN
PROGRAM
PROGRAM
Track number
Total playback time of the programmed tracks
(After 2 seconds)
Program order number
FS-SD58V_A2.fm Page 15 Thursday, September 28, 2000 4:50 PM
16
English
Using the Video CD Player
(Video CDs, CD-Gs)
You can play video CDs (with or without the Playback Con-
trol (PBC) function) and CD Graphics (CD-Gs) to watch the
picture on your TV while listening to the sound on video
CDs and CD-Gs.
SVCDs and DVDs cannot be used.
❏Before playing video CDs and CD-Gs
• Make sure that the connection between the System and
your TV is correct. (See page 7.)
Setting the TV System
(Using the Unit)
To view a picture of video CDs or CD-Gs, it is required to
set the System’s TV system according to your TV system.
Relationship among the playable CDs, System’s
TV system and your TV system:
1
Turn on the TV and select the video
input on the TV.
2
Turn on the System and press the CD
#¥8 button.
3
While pressing and holding the
7
button
on the Unit, press the VOLUME + or -
button on the Unit.
The current TV system (“PAL” for example) appears on
the display for five seconds.
4
Within five seconds, press the VOLUME
+ (or –) button to select the TV system.
Each time you press the button, the TV system changes
as follows.
5
Within five seconds, press the
7
button
on the Unit.
• If you play a CD of NTSC system in PAL AUTO system on
a PAL exclusive TV, the image may be distorted. If this
happen, change to “PAL”.
• When you play a CD of NTSC system in PAL AUTO system
on a multisystem TV, the image may blink for a moment.
This symptom occurs when the System detects the formu-
la of the CD and is not a malfunction.
Selecting the Audio Channel
This function may be used for CDs that support multiplex
function. In addition to the normal stereo sound output, you
can select L channel or R channel independently.
Press the button on the Remote Control.
Each time you press the button, the selected channel chang-
es as follows:
NORMAL (Stereo) --> Lch MONO --> Rch MONO --> (back
to the beginning)
• When “Lch MONO” or “Rch MONO” is selected, the
first push of the button will show the current selection.
• The channel selection returns to “NORMAL (Stereo)”
when the CD is ejected, when other source (e.g. FM/AM)
is selected, or when the system is turned off.
REMOTE CONTROL
VOLUME
FM MODE
MPX
DIMMER SLEEP
DISPLAY DOOR SLIDE
PLAY MODE REPEAT CANCEL
AHB PRO
TONE
CONTROL
CLOCK
/ TIMER
HIGHLIGHT
PBC ON / OFF
VCD NUMBER
SELECT
NEXTPREV
VCD NUMBER
VIDEO INTRO STILL
UP
SET
DOWN
MD
/
AUX FM
/
AM
CD
FADE MUTING
ON SCREEN
CD
VOLUME
FM/AMMD/AUX
PROGRAM
RANDOM ALL
2019181716151413121110
987654321
* When the System is in use, the display shows other items as well.
For simplicity, we show here only the items described in this section.
< PREV
VIDEO INTRO
STILL
HIGHLIGHT
SELECT
SET
> NEXT
&
VCD NUMBER DOWN
CD
#/8
Music calendar
Play mode indicator
Track number exceeding
20 is not displayed.
PBC ON/OFF
7
VCD
NUMBER
+, -
VOLUME +, -
PBC
ON/OFF
&
RETURN
Repeat indicators
Track number, Playing time, Preset number
ON SCREEN
VCD NUMBER UP
PREV NEXT
SELECT
(When playing video CDs)
Playable CD System’s TV system Your TV system
NTSC/PAL NTSC NTSC
NTSC/PAL PAL PAL
NTSC/PAL PAL AUTO Multisystem
VOLUME VOLUME
PAL NTSC
PAL AUTO
PAL: for PAL exclusive TV
NTSC: for NTSC exclusive TV
PAL AUTO: for multisystem TV
FS-SD58V_A3.fm Page 16 Thursday, September 28, 2000 4:51 PM
17
Using the Video CD Player (Video CDs, CD-Gs)
English
Playing Video CDs with PBC
Function
The System provides a Playback Control (PBC) function
which utilizes a procedure (menu selection) programmed in
a video CD.
What is the Playback Control (PBC) function?
The PBC function allows you to enjoy the following fea-
tures.
• Menu-driven playback
You can interact with the TV screen using a menu dis-
play to select and play an entry.
• High-resolution still image display
You can display high-quality images four times clearer
than video pictures.
❏For operation, refer to the instructions supplied for the
video CD.
❏You can play video CDs with PBC function using the
menu screen (Menu-Driven Play) or without using the
menu screen (Continuous Play).
• The playback operation procedure may differ depending
on the video CD you use.
• Sometimes due to improper manufacturing, video CDs will
function differently.
Playing Video CDs with the PBC Function
Using the Menu Screen (Menu-Driven Play)
❏Before playing, make sure that Repeat indicator “(”or
“
(ALL” is not lit. If lit, press the REPEAT button on the
Remote Control until it disappears.
❏Also, make sure that the “PROGRAM” or RANDOM in-
dicator is not lit. If lit, press the PLAY MODE button on
the Remote Control until it disappears.
1
Insert a video CD with the PBC function.
“PBC” will appear on the display.
2
Press the CD
#¥8
button.
“PBC” appears on the display and the first menu will
appear on the TV screen.
3
To move through the next menu, press
the following button.
On the Unit:
Press the NEXT or PREV button.
On the Remote Control:
Press the NEXT or PREV button.
4
To select the item (track) in the menu
and play it, press the following buttons.
On the Unit:
1. Press the VCD NUMBER + or – button to select the item
(“SEL
**
”) you want to play.
2. Press the SELECT button to play it back.
On the Remote Control:
1. Press the VCD NUMBER UP or DOWN button to se-
lect the item (“SEL
**
”) you want to play.
2. Press the SELECT button to play it back.
• The next track will be automatically played after the cur-
rent track is finished.
• While a part of movie is displayed on the TV in step 2,
pressing the
SELECT button causes the track being
played to play from the beginning.
To pause, press the STILL button on the Remote Control.
To resume pause, press the CD
#
/
8
button.
To stop playback press the
7
button until a blue appears
on the TV screen.
To select other item during playback, repeat step 4.
• Program Play, Random Play and Repeating Tracks cannot
be made in this Menu-Driven Play.
• When the video CD is paused for about 10 minutes, the
screen background automatically fades out to prevent
screen burn-in.
Basic Remote Control and Unit Button Functions for Menu-Driven Play:
CD
(within 5
seconds) SELECT
SELECT
VCD NUMBER
VCD NUMBER
UP
SET
DOWN
(within 5
seconds)
5HPRWHý&RQWURO 8QLW )XQFWLRQ
PREV / NEXT PREV / NEXT 0RYHýWKURXJKýPHQXï
VCD NUMBER
UP/DOWN
VCD NUMBER +/- 6HOHFWýDýVSHFLILFýPHQXýLWHPï
SELECT
(SET)
SELECT
(CD #¥8)
(QWHUVýWKHýVHOHFWHGýYLGHRý&'ýQXPEHUýRUýLWHPïý:KHQýDýSDUWýRIýPRYLHýLVýGLVð
SOD\HGýRQýWKHý79ýVFUHHQñýVWDUWVýSOD\LQJýWKDWýWUDFNýIURPýWKHýEHJLQQLQJï
ý
&&ýRETURN 5HWXUQVýWRýWKHýSUHYLRXVýPHQXýGXULQJýSOD\EDFNï
FS-SD58V_A3.fm Page 17 Thursday, September 28, 2000 4:51 PM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/