Cisco 15216 EDFA2 User manual

FINAL DRAFT - CISCO CONFIDENTIAL

Corporate Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 526-4100

Cisco ONS 15216 EDFA2

Operations Guide

Product and Software Release 2.3

August 2003

Text Part Number: 78-16033-01

FINAL DRAFT - CISCO CONFIDENTIAL

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required

to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not

installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to

comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable

protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital

devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television

communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its

peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

• Turn the television or radio antenna until the interference stops.

• Move the equipment to one side or the other of the television or radio.

• Move the equipment farther away from the television or radio.

• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits

controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

CCIP, CCSP, the Cisco Arrow logo, the Cisco Powered Network mark, the Cisco Systems Verified logo, Cisco Unity, Follow Me Browsing, FormShare, iQ Net Readiness

Scorecard, Networking Academy, and ScriptShare are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, The Fastest Way to Increase

Your Internet Quotient, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCNA, CCNP, Cisco, the

Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Empowering the

Internet Generation, Enterprise/Solver, EtherChannel, EtherSwitch, Fast Step, GigaStack, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, LightStream, MGX,

MICA, the Networkers logo, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, RateMUX, Registrar, SlideCast, SMARTnet, StrataView Plus, Stratm, SwitchProbe,

TeleRouter, TransPath, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries.

All other trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship

between Cisco and any other company. (0303R)

Cisco ONS 15216 EDFA2 Operations Guide

FINAL DRAFT - CISCO CONFIDENTIAL

iii

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

CONTENTS

Preface xix

Obtaining Documentation xix

Cisco.com xix

Optical Networking Product Documentation CD-ROM xix

Ordering Documentation xix

Documentation Feedback xx

Obtaining Technical Assistance xx

Cisco.com xx

Technical Assistance Center xxi

Obtaining Additional Publications and Information xxii

CHAPTER

1 Applications 1-1

1.1 Bandwidth On Demand 1-1

1.2 Wavelength Protection Switching 1-1

1.3 Key Features 1-2

1.3.1 Constant Gain 1-3

1.3.2 Gain Flattening 1-3

1.3.3 Transient Suppression 1-4

1.3.4 Low Noise 1-4

1.3.5 SNMP MIBs 1-4

1.3.6 TL1 1-4

CHAPTER

2 Technical Specifications 2-1

2.1 Optical Specifications 2-1

2.1.1 Maximum Input Power 2-2

2.1.2 Channel Loading 2-2

2.2 Electrical Specifications 2-3

2.3 Mechanical Specifications 2-4

2.4 External Features 2-4

2.5 Front Panel 2-5

CHAPTER

3 Installation 3-1

3.1 Introduction 3-1

FINAL DRAFT - CISCO CONFIDENTIAL

Contents

iv

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

3.2 Standard Precautions 3-1

3.3 Placement and Power Connection 3-1

3.3.1 General Rack Considerations 3-1

3.3.2 Rack Installation and Power Supply Connection Procedures 3-2

3.4 SC/UPC Optical Ports 3-3

3.4.1 Safety Requirements 3-3

3.4.2 Optical Connection Procedure 3-3

3.4.3 Optical Amplification Operation Verification Procedure 3-4

3.5 Communications 3-5

3.5.1 Alarm Out Relay Interface (RJ-45) 3-5

3.5.2 Alarm LEDs 3-6

3.5.3 Serial Interface (EIA/TIA-232) Communication 3-7

3.5.4 Serial Interface Remote Communication via Modem 3-11

3.5.5 LAN Interface (Ethernet) 3-14

CHAPTER

4 Provisioning Using ASH and SNMP 4-1

4.1 Log In via RS-232 (EIA/TIA-232) Port Using HyperTerminal 4-1

4.2 Set IP Address 4-3

4.3 Log In via LAN Port Using Telnet (Optional) 4-3

4.4 Set Date and Time 4-4

4.5 Set Power Bus Mode (Simplex or Duplex) 4-4

4.6 Verify Amplifier Operational Status 4-4

4.7 Set Gain 4-5

4.8 Set Alarm Thresholds 4-5

4.9 Set Password 4-10

4.10 Add Users 4-11

4.11 Save Changes 4-11

4.12 Log Off 4-12

4.13 Back Up System Configuration 4-12

4.14 Restore System Configuration 4-13

4.15 Recover Default Password 4-14

CHAPTER

5 SNMP MIB Installation and Configuration 5-1

5.1 SNMP Overview 5-1

5.1.1 SNMP Components 5-1

5.1.2 ONS 15216 EDFA2 SNMP Elements 5-2

5.1.3 SNMP MIBs and Message Types 5-3

FINAL DRAFT - CISCO CONFIDENTIAL

Contents

v

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

5.1.4 Command Syntax Using the SNMP Agent 5-4

5.2 Enabling SNMP Remote Management Community Strings 5-5

5.2.1 Creating a View 5-6

5.2.2 Creating a Community Entry 5-7

5.3 Setup for CTM Access 5-10

5.4 Tables and Groups 5-11

5.4.1 CfgGroup Table 5-12

5.4.2 PumpCfgEntry Table 5-14

5.4.3 OverallStatusGroup Table 5-16

5.4.4 OverallControl Table 5-18

5.4.5 PumpStatusEntry Table 5-18

5.4.6 AlarmEntry Table 5-19

5.4.7 OpGroup Table 5-20

5.4.8 VersionGroup Table 5-21

5.5 Setting Up Traps 5-21

5.5.1 Display Trap Command 5-22

5.5.2 Set Trap Command 5-23

5.5.3 Set Agent Trap Enable 5-23

5.5.4 Get Agent Trap Enable 5-24

5.6 Retrieving Information 5-24

5.6.1 IP Address 5-24

5.6.2 Date and Time 5-25

5.6.3 Power Gain 5-26

5.6.4 Case Temperature 5-27

5.6.5 Power Bus 5-29

5.6.6 Input Power (Signal) 5-30

5.6.7 Output Power 5-31

5.6.8 Database Backup and Restore 5-34

5.6.9 Alarm Entry 5-36

5.7 Summary of SNMP Alarms 5-37

CHAPTER

6 ASH Commands 6-1

6.1 Summary of Security Permissions for ASH Commands 6-1

6.2 Configuration Commands 6-6

6.2.1 srom cfg boot display Command 6-6

6.2.2 srom cfg boot modify Command 6-7

6.2.3 srom cfg ip display Command 6-7

6.2.4 srom cfg ip modify Command 6-8

6.2.5 pdm busmode display Command 6-8

FINAL DRAFT - CISCO CONFIDENTIAL

Contents

vi

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

6.2.6 pdm busmode modify Command 6-9

6.2.7 pdm cfg threshold bus display Command 6-9

6.2.8 pdm cfg threshold bus modify Command 6-9

6.2.9 gain gain display Command 6-9

6.2.10 gain gain modify Command 6-10

6.2.11 voa power input display Command 6-10

6.3 Administrative Commands 6-10

6.3.1 clear Command 6-11

6.3.2 exit Command 6-11

6.3.3 help Command 6-11

6.3.4 history Command 6-11

6.3.5 login and logoff Commands 6-12

6.3.6 processor reset Command 6-12

6.4 Shell Commands 6-12

6.4.1 shell lines set Command 6-13

6.4.2 shell more enable and disable Commands 6-13

6.4.3 shell status display Command 6-13

6.4.4 shell type modify Command 6-13

6.5 Flash File System Commands 6-14

6.5.1 ffs file list Command 6-14

6.6 SNMP Commands 6-15

6.6.1 snmp attribute get Command 6-15

6.6.2 snmp attribute list Command 6-16

6.6.3 snmp attribute set Command 6-17

6.6.4 snmp mib display Command 6-17

6.6.5 snmp mib get Command 6-18

6.6.6 snmp mib list Command 6-18

6.6.7 snmp row display Command 6-19

6.6.8 snmp row get Command 6-20

6.6.9 snmp row set Command 6-20

6.6.10 snmp subtree display Command 6-21

6.6.11 snmp subtree get Command 6-21

6.6.12 snmp subtree list Command 6-22

6.6.13 snmp table display Command 6-23

6.6.14 snmp table get Command 6-24

6.6.15 snmp table list Command 6-24

6.6.16 snmp tree attribute list Command 6-25

6.7 User Commands 6-25

6.7.1 user entry create Command 6-26

FINAL DRAFT - CISCO CONFIDENTIAL

Contents

vii

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

6.7.2 user entry edit Command 6-26

6.7.3 user entry delete Command 6-27

6.7.4 user file display and user name display Commands 6-27

6.7.5 user inactivity modify and user inactivity display Commands 6-28

6.7.6 user passwd set Command 6-28

6.7.7 user active list Command 6-29

6.7.8 user active message send Command 6-29

6.8 Manufacturing Information Access Commands 6-30

6.8.1 snmp table display local entPhysicalEntry Command 6-30

6.8.2 snmp table display local cerent15216EdfaCommTrapEntry Command 6-30

6.9 Restore Commands 6-31

6.9.1 backup system Command 6-31

6.9.2 restore system Command 6-31

6.10 Manufacturer Mode 6-32

6.10.1 manufacturer restore defaults passwords Command 6-32

6.10.2 manufacturer restore defaults all Command 6-32

CHAPTER

7 FTP Command Line 7-1

7.1 FTP Command Line 7-1

7.1.1 Example of FTP from a Remote Server 7-1

7.1.2 Example of FTP to a Remote Server 7-2

7.2 FTP Commands 7-3

CHAPTER

8 Provisioning Using TL1 8-1

8.1 Log In via RS-232 (EIA/TIA-232) Port Using HyperTerminal 8-1

8.2 Set IP Address 8-3

8.3 Log In via LAN Port Using Telnet (Optional) 8-3

8.4 Set Date and Time 8-4

8.5 Set Power Bus Mode (Simplex or Duplex) 8-4

8.6 Verify Amplifier Operational Status 8-4

8.7 Set Gain 8-5

8.8 Set Alarm Thresholds 8-5

8.9 Set Password 8-10

8.10 Add Users 8-11

8.11 Log Off 8-11

8.12 Back Up System Configuration 8-11

8.13 Restore System Configuration 8-12

FINAL DRAFT - CISCO CONFIDENTIAL

Contents

viii

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

CHAPTER

9 TL1 Commands 9-1

9.1 Introduction 9-1

9.2 Connection to the ONS 15216 EDFA2 9-1

9.3 Explanation of Command Parameters 9-1

9.3.1 Source Identifier (sid) and Target Identifier (tid) 9-1

9.3.2 Command Code Modifier (ccm) 9-2

9.3.3 Access Identifier (aid) 9-2

9.3.4 Correlation Tag (ctag) 9-2

9.4 Notation 9-2

9.5 Summary of Autonomous Alarms and Messages 9-3

9.6 Summary of Security Permissions for TL1 Commands 9-6

9.7 TL1 Commands and Autonomous Messages 9-9

9.7.1 ACT-USER 9-9

9.7.2 ALW-MSG-ALL 9-9

9.7.3 APPLY 9-11

9.7.4 CANC-USER 9-12

9.7.5 COPY-RFILE 9-12

9.7.6 CPY-MEM 9-14

9.7.7 DLT-RFILE 9-15

9.7.8 DLT-USER-SECU 9-16

9.7.9 ED-DAT 9-16

9.7.10 ED-DWDM 9-17

9.7.11 ED-ENV 9-18

9.7.12 ED-NE-GEN 9-19

9.7.13 ED-PID 9-20

9.7.14 ED-USER-SECU 9-21

9.7.15 ENT-USER-SECU 9-21

9.7.16 INH-MSG-ALL 9-22

9.7.17 INIT-SYS 9-25

9.7.18 REPT ALM DWDM 9-25

9.7.19 REPT ALM ENV 9-27

9.7.20 REPT ALM EQPT 9-28

9.7.21 REPT EVT DWDM / REPT EVT ENV / REPT EVT EQPT 9-30

9.7.22 REPT EVT FXFR 9-32

9.7.23 RTRV-ALM-ALL 9-33

9.7.24 RTRV-ALM-DWDM 9-35

9.7.25 RTRV-ALM-ENV 9-37

9.7.26 RTRV-ALM-EQPT 9-38

9.7.27 RTRV-AO 9-40

FINAL DRAFT - CISCO CONFIDENTIAL

Contents

ix

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

9.7.28 RTRV-COND-ALL 9-41

9.7.29 RTRV-COND-DWDM 9-43

9.7.30 RTRV-COND-ENV 9-44

9.7.31 RTRV-COND-EQPT 9-46

9.7.32 RTRV-DFLT-SECU 9-47

9.7.33 RTRV-DWDM 9-48

9.7.34 RTRV-ENV 9-50

9.7.35 RTRV-HDR 9-51

9.7.36 RTRV-INV 9-51

9.7.37 RTRV-NE-GEN 9-52

9.7.38 RTRV-RFILE 9-54

9.7.39 RTRV-TH-DWDM 9-55

9.7.40 RTRV-TH-ENV 9-56

9.7.41 RTRV-TH-EQPT 9-57

9.7.42 RTRV-TOD 9-59

9.7.43 RTRV-USER-SECU 9-60

9.7.44 SET-ATTR-SECUDFLT 9-60

9.7.45 SET-TH-DWDM 9-61

9.7.46 SET-TH-ENV 9-62

9.7.47 SET-TH-EQPT 9-63

9.7.48 STA-LOCL-RST 9-64

CHAPTER

10 Troubleshooting 1

10.1 Alarm Indicators 2

10.1.1 LEDs and Office Alarms 2

10.1.2 Optical Alarms 4

10.1.3 Equipment Alarms 6

10.1.4 Environmental Alarms 7

10.2 Troubleshooting Typical Scenarios 7

10.2.1 No Output Power after Adjusting Gain Settings 7

10.2.2 2.0.1 to 2.2.1 Upgrade Attempt 8

10.2.3 Image File Download Incomplete 8

10.2.4 Boot Up Failure 8

10.2.5 No Response from RS-232 Port 9

10.2.6 No Response from LAN Port 9

10.2.7 LAN Port Activity LED Stays On 9

10.2.8 Lost Password 10

10.3 Status Information Needed by Cisco TAC 11

FINAL DRAFT - CISCO CONFIDENTIAL

Contents

x

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

APPENDIX

A Regulatory Compliance and Safety Information A-1

Regulatory Compliance A-1

Translated Safety Warnings A-2

Warning Definition A-4

DC Power Supply Warning A-6

Installation Warning A-7

Power Cord Warning A-7

No On/Off Switch Warning A-8

SELV Circuit Warning A-9

Laser Radiation Warning A-10

Laser Beam Warning A-11

Power Cabling Warning A-11

Grounded Equipment Warning A-12

Ground Connection Warning A-13

Jewelry Removal Warning A-14

Qualified Personnel Warning A-15

Supply Circuit Warning A-15

Power Supply Wiring Warning A-16

Invisible Laser Radiation Warning A-17

Incorrect Connection Warning A-18

Ground Conductor Warning A-19

Voltages on DC-input Power Supply Terminals A-20

More Than One Power Supply A-21

Cisco ONS 15216 EDFA2 Rack Installation A-21

Exposed DC Power Wire Warning A-22

48 VDC Power System A-23

Chassis Power Connection A-24

Cisco ONS 15216 EDFA2 Temperature Requirement A-25

VCCI Compliance for Class B Equipment A-26

SELV-IEC 60950 DC Power Supply Warning A-26

Cisco ONS 15216 EDFA2 Power Circuit Overload Warning A-27

Product Disposal Warning A-28

Energy Hazard A-29

Unit Grounding Protection Warning A-30

DC Power Disconnection Warning A-31

Ground Wire Warning A-32

Declaration of Conformity with Regard to the Directives 73/23/EEC and 89/336/EEC as amended by

Directive 93/68/EEC

A-33

Declaration of Conformity to R&TTE Directive 1999/5/EEC for the European Community, Switzerland,

Norway, Iceland and Liechtenstein

A-34

FINAL DRAFT - CISCO CONFIDENTIAL

Contents

xi

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

Class B EMC Warning A-35

Safety Requirements Warning A-35

Laser Radiation Warning A-36

Fiber Disconnect Sequence Warning A-37

Optical Connector Warning A-38

Optical Connector Disconnect Warning A-38

Eye Damage Warning A-39

Static Electricity Warning A-40

Connector Cleaning Warning A-41

Cable Connection Sequence Warning A-42

Module Removal Warning A-43

DC Power SELV Requirement Warning A-44

Reinforced Insulation Warning A-45

Power Supply Voltage Warning A-46

DC Power Supply Connection Warning A-46

I

NDEX

FINAL DRAFT - CISCO CONFIDENTIAL

Contents

xii

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

FIGURES

FINAL DRAFT - CISCO CONFIDENTIAL

xiii

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

Figure 1-1 Wavelength Protection Switching 1-2

Figure 1-2 ONS 15216 EDFA2 Block Diagram 1-2

Figure 1-3 Gain Flattening Filter 1-3

Figure 2-1 ONS 15216 EDFA2 Dimensions 2-5

Figure 2-2 ONS 15216 EDFA2 Front Panel 2-5

Figure 3-1 ONS 15216 EDFA2 Optical Connections 3-4

Figure 3-2 HyperTerminal Connect To Dialog Box 3-8

Figure 3-3 HyperTerminal COM1 Properties Dialog Box 3-9

Figure 3-4 Optical Amplifier Properties Dialog Box (Connect To Tab) 3-9

Figure 3-5 Optical Amplifier Properties Dialog Box (Settings Tab) 3-10

Figure 3-6 HyperTerminal ASCII Setup Dialog Box 3-10

Figure 3-7 Remote Communication 3-11

Figure 3-8 DB-9 Pinout for RS-232 (EIA/TIA-232) Port 3-14

Figure 4-1 ONS 15216 EDFA2 Front Panel 4-6

Figure 5-1 SNMP Elements 5-2

Figure 5-2 SNMP Agent and MIB 5-3

Figure 8-1 ONS 15216 EDFA2 Front Panel 8-6

FINAL DRAFT - CISCO CONFIDENTIAL

Figures

xiv

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

TABLES

FINAL DRAFT - CISCO CONFIDENTIAL

xv

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

Table 2-1 ONS 15216 EDFA2 Optical Specifications 2-1

Table 2-2 Maximum Channel Power 2-2

Table 2-3 ONS 15216 EDFA2 Electrical Specifications 2-3

Table 2-4 ONS 15216 EDFA2 Mechanical Specifications 2-4

Table 2-5 ONS 15216 EDFA2 Front Panel Features 2-6

Table 3-1 Gain Range 3-4

Table 3-2 Alarm Pinout and Definitions (RJ-45) 3-5

Table 3-3 Equipment Checklist 3-7

Table 3-4 Communication Component List 3-11

Table 3-5 Modem DIP Switch Setting 3-12

Table 3-6 Modem Settings 3-13

Table 4-1 Alarm Threshold Attribute Definitions 4-7

Table 5-1 SNMP Operation Types 5-4

Table 5-2 Default Community Strings 5-5

Table 5-3 Creating a View 5-7

Table 5-4 Creating a Community Entry 5-8

Table 5-5 SNMP Operation Decimal Values 5-9

Table 5-6 cerent15216EdfaCfgGroup Variable Descriptions 5-12

Table 5-7 cerent15216EdfaPumpCfgEntry Variable Descriptions 5-14

Table 5-8 cerent15216EdfaOverallStatusGroup Variable Descriptions 5-17

Table 5-9 cerent15216EdfaOverallControl Variable Descriptions 5-18

Table 5-10 cerent15216EdfaPumpStatusEntry Variable Descriptions 5-18

Table 5-11 cerent15216EdfaAlarmEntry Variable Descriptions 5-19

Table 5-12 cerent15216EdfaOpGroup Variable Descriptions 5-20

Table 5-13 cerent15216EdfaVersionGroup Variable Descriptions 5-21

Table 5-14 Notification Types that Initiate a Trap 5-22

Table 5-15 cerent15216EdfaSromIpMgmtGroup Command Attributes 5-25

Table 5-16 cerent15216EdfaRtcDateAndTime Command Attributes 5-26

Table 5-17 SNMP Alarms 5-37

Table 6-1 ASH Commands Security Permissions (Access Levels) 6-1

Table 8-1 Alarm Threshold Attribute Definitions 8-7

FINAL DRAFT - CISCO CONFIDENTIAL

Tables

xvi

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

Table 9-1 Command Code Modifiers 9-2

Table 9-2 Access Identifiers 9-2

Table 9-3 TL1 Notation Symbols 9-3

Table 9-4 TL1 Autonomous Alarms 9-3

Table 9-5 TL1 Autonomous Events 9-4

Table 9-6 TL1 Autonomous File Transfer Events 9-5

Table 9-7 TL1 Autonomous Clear Alarms 9-5

Table 9-8 TL1 Commands and Messages Security Permissions (Access Levels) 9-6

Table 9-9 ACT-USER Syntax Description 9-9

Table 9-10 ALW-MSG-ALL Syntax Description 9-10

Table 9-11 CANC-USER Syntax Description 9-12

Table 9-12 COPY-RFILE Syntax Description 9-13

Table 9-13 CPY-MEM Syntax Description 9-14

Table 9-14 DLT-RFILE Syntax Description 9-15

Table 9-15 DLT-USER-SECU Syntax Description 9-16

Table 9-16 ED-DAT Syntax Description 9-16

Table 9-17 ED-DWDM Syntax Description 9-17

Table 9-18 ED-ENV Syntax Description 9-18

Table 9-19 ED-NE-GEN Syntax Description 9-19

Table 9-20 ED-PID Syntax Description 9-20

Table 9-21 ED-USER-SECU Syntax Description 9-21

Table 9-22 ENT-USER-SECU Syntax Description 9-22

Table 9-23 INH-MSG-ALL Syntax Description 9-22

Table 9-24 INIT-SYS Syntax Description 9-25

Table 9-25 REPT ALM DWDM Syntax Description 9-26

Table 9-26 REPT ALM ENV Syntax Description 9-27

Table 9-27 REPT ALM EQPT Syntax Description 9-29

Table 9-28 REPT EVT DWDM / REPT EVT ENV / REPT EVT EQPT Syntax Description 9-31

Table 9-29 REPT EVT FXFR Syntax Description 9-33

Table 9-30 RTRV-ALM-ALL Syntax Description 9-34

Table 9-31 RTRV-ALM-DWDM Syntax Description 9-36

Table 9-32 RTRV-ALM-ENV Syntax Description 9-37

Table 9-33 RTRV-ALM-EQPT Syntax Description 9-38

Table 9-34 RTRV-AO Syntax Description 9-40

Table 9-35 RTRV-COND-ALL Syntax Description 9-41

FINAL DRAFT - CISCO CONFIDENTIAL

Tables

xvii

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

Table 9-36 RTRV-COND-DWDM Syntax Description 9-43

Table 9-37 RTRV-COND-ENV Syntax Description 9-45

Table 9-38 RTRV-COND-EQPT Syntax Description 9-46

Table 9-39 RTRV-DFLT-SECU Syntax Description 9-48

Table 9-40 RTRV-DWDM Syntax Description 9-49

Table 9-41 RTRV-ENV Syntax Description 9-50

Table 9-42 RTRV-HDR Syntax Description 9-51

Table 9-43 RTRV-INV Syntax Description 9-52

Table 9-44 RTRV-NE-GEN Syntax Description 9-53

Table 9-45 RTRV-RFILE Syntax Description 9-54

Table 9-46 RTRV-TH-DWDM Syntax Description 9-55

Table 9-47 RTRV-TH-ENV Syntax Description 9-57

Table 9-48 RTRV-TH-EQPT Syntax Description 9-58

Table 9-49 RTRV-TOD Syntax Description 9-59

Table 9-50 RTRV-USER-SECU Syntax Description 9-60

Table 9-51 SET-ATTR-SECUDFLT Syntax Description 9-61

Table 9-52 SET-TH-DWDM Syntax Description 9-61

Table 9-53 SET-TH-ENV Syntax Description 9-62

Table 9-54 SET-TH-EQPT Syntax Description 9-63

Table A-1 Regulatory Standards Compliance A-1

FINAL DRAFT - CISCO CONFIDENTIAL

Tables

xviii

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

FINAL DRAFT - CISCO CONFIDENTIAL

xix

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

Preface

Obtaining Documentation

Cisco provides several ways to obtain documentation, technical assistance, and other technical

resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation on the World Wide Web at this URL:

http://www.cisco.com/univercd/home/home.htm

You can access the Cisco website at this URL:

http://www.cisco.com

International Cisco web sites can be accessed from this URL:

http://www.cisco.com/public/countries_languages.shtml

Optical Networking Product Documentation CD-ROM

Optical networking-related documentation, including the Cisco ONS 15216 EDFA2 Operations Guide,

is available in a CD-ROM package that ships with your product. The Optical Networking Product

Documentation CD-ROM, a member of the Cisco Connection Family, is updated as required. Therefore,

it might be more current than printed documentation. To order additional copies of the Optical

Networking Product Documentation CD-ROM, contact your local sales representative or customer

service. The CD-ROM package is available as a single unit or through an annual subscription.

Ordering Documentation

You can find instructions for ordering documentation at this URL:

http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm

You can order Cisco documentation in these ways:

• Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from

the Networking Products MarketPlace:

http://www.cisco.com/en/US/partner/ordering/index.shtml

FINAL DRAFT - CISCO CONFIDENTIAL

xx

Cisco ONS 15216 EDFA2 Operations Guide

78-16033-01

Preface

Obtaining Technical Assistance

• Registered Cisco.com users can order the Documentation CD-ROM (Customer Order Number

DOC-CONDOCCD=) through the online Subscription Store:

http://www.cisco.com/go/subscription

• Nonregistered Cisco.com users can order documentation through a local account representative by

calling Cisco Systems Corporate Headquarters (California, U.S.A.) at 408 526-7208 or, elsewhere

in North America, by calling 800 553-NETS (6387).

Documentation Feedback

You can submit comments electronically on Cisco.com. On the Cisco Documentation home page, click

Feedback at the top of the page.

You can e-mail your comments to bug-doc@cisco.com.

You can submit your comments by mail by using the response card behind the front cover of your

document or by writing to the following address:

Cisco Systems

Attn: Customer Document Ordering

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

Obtaining Technical Assistance

Cisco provides Cisco.com, which includes the Cisco Technical Assistance Center (TAC) Website, as a

starting point for all technical assistance. Customers and partners can obtain online documentation,

troubleshooting tips, and sample configurations from the Cisco TAC website. Cisco.com registered users

have complete access to the technical support resources on the Cisco TAC website, including TAC tools

and utilities.

Cisco.com

Cisco.com offers a suite of interactive, networked services that let you access Cisco information,

networking solutions, services, programs, and resources at any time, from anywhere in the world.

Cisco.com provides a broad range of features and services to help you with these tasks:

• Streamline business processes and improve productivity

• Resolve technical issues with online support

• Download and test software packages

• Order Cisco learning materials and merchandise

• Register for online skill assessment, training, and certification programs

To obtain customized information and service, you can self-register on Cisco.com at this URL:

http://www.cisco.com

Page is loading ...

Cisco 15216 EDFA2 User manual

This manual is also suitable for

Cisco 15216 EDFA2 User manual

Related papers

Other documents