Kohler COMMAND PRO CS Series User manual

Brand: Kohler

Model: COMMAND PRO CS Series

Category: Garden tools

Type: User manual

COMMAND PRO CS SERIES4-12.75 HP

HORIZONTAL CRANKSHAFT

OWNER'S MANUAL

Safety Precautions

To ensure safe operations please read the following statements and understand their meaning.

Also refer to your equipment owner's manual for other important safety information. This manual

contains safety precautions which are explained below. Please read carefully.

WARNING

Warning is used to indicate the presence of a hazard that can cause severe personal injury,

death, or substantial property damage if the warning is ignored.

CAUTION

Caution is used to indicate the presence of a hazard that will or can cause minor personal injury

or property damage if the caution is ignored.

NOTE

Note is used to notify people of installation, operation, or maintenance information that is

important but not hazard-related.

For Your Safety!

These precautions should be followed at all times. Failure to follow these precautions could result in

injury to yourself and others.

Engine exhaust from this product

contains chemicals known to the

State of California to cause cancer,

birth defects, or other reproductive

harm.

California

Proposition 65 Warning

Explosive Fuel can cause fires and

severe burns.

Stop engine before filling fuel tank.

WARNING

Explosive Fuel!

Gasoline is extremely flammable

and its vapors can explode if

ignited. Store gasoline only in

approved containers, in well

ventilated, unoccupied buildings,

away from sparks or flames. Do not

fill the fuel tank while the engine is

hot or running, since spilled fuel

could ignite if it comes in contact

with hot parts or sparks from

ignition. Do not start the engine near

spilled fuel. Never use gasoline as a

cleaning agent.

Rotating Parts can cause severe

injury.

Stay away while engine is in

operation.

WARNING

Rotating Parts!

Keep hands, feet, hair, and clothing

away from all moving parts to

prevent injury. Never operate the

engine with covers, shrouds, or

guards removed.

Hot Parts can cause severe burns.

Do not touch engine while operating

or just after stopping.

WARNING

Hot Parts!

Engine components can get

extremely hot from operation. To

prevent severe burns, do not touch

these areas while the engine is

running–or immediately after it is

turned off. Never operate the engine

with heat shields or guards

removed.

Electrical Shock can cause injury.

Do not touch wires while engine is

running.

CAUTION

Electrical Shock!

Never touch electrical wires or

components while the engine is

running. They can be sources of

electrical shock.

Safety Precautions (Cont.)

Accidental Starts can cause severe

injury or death.

Disconnect and ground spark plug

lead before servicing.

WARNING

Carbon Monoxide can cause

severe nausea, fainting or death.

Do not operate engine in closed or

confined area.

WARNING

Lethal Exhaust Gases!

Engine exhaust gases contain

poisonous carbon monoxide.

Carbon monoxide is odorless,

colorless, and can cause death if

inhaled. Avoid inhaling exhaust

fumes, and never run the engine in

a closed building or confined area.

WARNING

Explosive Gas can cause fires and

severe acid burns.

Charge battery only in a well

ventilated area. Keep sources of

ignition away.

Accidental Starts!

Disabling engine. Accidental

starting can cause severe injury

or death. Before working on the

engine or equipment, disable the

engine as follows: 1) Disconnect the

spark plug lead(s). 2) Disconnect

negative (-) battery cable from

battery.

Explosive Gas!

Batteries produce explosive

hydrogen gas while being charged.

To prevent a fire or explosion,

charge batteries only in well

ventilated areas. Keep sparks, open

flames, and other sources of ignition

away from the battery at all times.

Keep batteries out of the reach of

children. Remove all jewelry when

servicing batteries.

Before disconnecting the negative

(–) ground cable, make sure all

switches are OFF. If ON, a spark will

occur at the ground cable terminal

which could cause an explosion if

hydrogen gas or gasoline vapors

are present.

Congratulations – You have selected a fine four-cycle, single cylinder, air-cooled engine. Kohler designs long

life strength and on-the-job durability into each engine…making a Kohler engine dependable…dependability you

can count on. Here are some reasons why:

• Efficient overhead valve design and splash lubrication provide maximum power, torque, and reliability under

all operating conditions.

• Dependable, maintenance free electronic ignition ensures fast, easy starts time after time.

• Kohler engines are easy to service. All routine service areas (like the oil fill/check plug, air cleaner, spark plug,

and carburetor) are easily and quickly accessible.

• Parts subject to the most wear and tear (like the cylinder liner, crankshaft, and camshaft) are made from

precision formulated cast iron. Because the cylinder liner can be rebored, these engines can last even longer.

• Every Kohler engine is backed by a worldwide network of over 10,000 distributors and dealers. Service

support is just a phone call away. Call 1-800-544-2444 (U.S. & Canada) for Sales & Service assistance.

To keep your engine in top operating condition, follow the maintenance procedures in this manual.

Figure 1. Location of Controls and Service Points on CS Engines.

Oil Recommendations

Using the proper type and weight of oil in the crankcase

is extremely important. So is checking oil daily and

changing oil regularly. Failure to use the correct oil, or

using dirty oil, causes premature engine wear and

failure.

Oil Type

Use high quality detergent oil of API (American

Petroleum Institute) service class SG, SH, SJ or

higher. Select the viscosity based on the air

temperature at the time of operation as shown in the

following table.

NOTE: Using other than service class SG, SH, SJ or

higher oil or extending oil change intervals

longer than recommended can cause engine

damage.

A logo or symbol on oil containers identifies the API

service class and SAE viscosity grade. See Figure 3.

Fuel Tank Cap

Air Cleaner

Cover Retaining

Knob

Fuel Tank

Choke Lever

Fuel

Shut-Off

Retractable Starter

Throttle Lever

Oil Sentry

Light

On/Off Switch

(some models)

Muffler Shield

Muffler

Spark Plug

Carburetor

Oil Drain

Valve Cover

Oil Fill/

Check Plug

Synthetic oils should not be used.

Figure 2. Viscosity Grades Table.

Figure 3. Oil Container Logo.

Refer to “Maintenance Instructions” beginning on

page 8 for detailed oil check and oil change

procedures.

Engine Identification Numbers

When ordering parts, or in any communication involving

an engine, always give the Model, Specification, and

Serial Numbers of the engine.

The engine identification numbers appear on a decal

(or decals) affixed to the engine shrouding. Include

letter suffixes, if there are any.

Record your engine identification numbers on the

identification label below (Figure 4) for future reference.

Fuel Recommendations

WARNING: Explosive Fuel!

Gasoline is extremely flammable and its vapors can

explode if ignited. Store gasoline only in approved

containers, in well ventilated, unoccupied buildings,

away from sparks or flames. Do not fill the fuel tank

while the engine is hot or running, since spilled fuel

could ignite if it comes in contact with hot parts or

sparks from ignition. Do not start the engine near spilled

fuel. Never use gasoline as a cleaning agent.

General Recommendations

Purchase gasoline in small quantities and store in

clean, approved containers. A container with a capacity

of 2 gallons or less with a pouring spout is

recommended. Such a container is easier to handle

and helps eliminate spillage during refueling.

Do not use gasoline left over from the previous season,

to minimize gum deposits in your fuel system and to

ensure easy starting.

Do not add oil to the gasoline.

Do not overfill the fuel tank. Leave room for the fuel to

expand.

Fuel Type

For best results use only clean, fresh, unleaded

gasoline with a pump sticker octane rating of 87 or

higher. In countries using the Research method, it

should be 90 octane minimum.

Unleaded gasoline is recommended as it leaves less

combustion chamber deposits. Leaded gasoline may be

used in areas where unleaded is not available and

exhaust emissions are not regulated. Be aware

however, that the cylinder head will require more

frequent service.

Gasoline/Alcohol blends

Gasohol (up to 10% ethyl alcohol, 90% unleaded

gasoline by volume) is approved as a fuel for Kohler

engines. Other gasoline/alcohol blends are not

approved.

Gasoline/Ether blends

Methyl Tertiary Butyl Ether (MTBE) and unleaded

gasoline blends (up to a maximum of 15% MTBE by

volume) are approved as a fuel for Kohler engines.

Other gasoline/ether blends are not approved.

Figure 4. Engine Identification Label.

The Emission Compliance Period referred to on the

Emission Control or Air Index label indicates the

number of operating hours for which the engine has

been shown to meet Federal and CARB emission

requirements. The following table provides the Engine

Complicance Period (in hours) associated with the

category descriptor found on the certification label.

Emission Compliance Period (Hours)

EPA

CARB

Category C

250 Hours

Moderate

125 Hours

Category B

500 Hours

Intermediate

250 Hours

Category A

1000 Hours

Extended

500 Hours

Refer to certification label for engine displacement.

Exhaust Emission Control System for models

CS4-12.75 is EM.

(REF:_______________ )

FAMILY

TYPE APP

MODEL NO.

SPEC. NO.

DISPL. (CC)

SERIAL NO.

OEM PROD. NO.

EMISSION COMPLIANCE PERIOD:

EPA: CATEGORY A

CERTIFIED ON: UNLEADED GASOLINE

N432

REFER TO OWNER'S MANUAL FOR SAFETY,

MAINTENANCE SPECS, AND ADJUSTMENTS

1-800-544-2444 www.kohlerengines.com

KOHLER CO. KOHLER, WISCONSIN USA

IMPORTANT ENGINE INFORMATION

THIS ENGINE MEETS U.S. EPA PHASE II, 2002-2005

CALIFORNIA AND EC STAGE II (SN:4) EMISSION

CONTROL REGS FOR SI SMALL OFF–ROAD

ENGINES

Operating Instructions

Also read the operating instructions of the equipment this engine powers.

Pre-Start Checklist

NOTE: This engine has been shipped without engine

oil. Fill with oil, otherwise it will not start.

• Check oil level. Add oil if low. Do not overfill.

• Check fuel level. Add fuel if low.

• Check cooling air intake areas and external

surfaces of engine. Make sure they are clean and

unobstructed.

• Check that the air cleaner components and all

shrouds, equipment covers, and guards are in

place and securely fastened.

• Check that any clutches or transmissions are

disengaged or placed in neutral.

WARNING: Lethal Exhaust Gases!

Engine exhaust gases contain poisonous carbon

monoxide. Carbon monoxide is odorless, colorless,

and can cause death if inhaled. Avoid inhaling exhaust

fumes, and never run the engine in a closed building or

confined area.

Cold Weather Starting Hints

1. Be sure to use the proper oil for the temperature

expected. See Figure 2 on page 4.

2. Declutch all possible external loads.

3. Set speed control at part throttle position.

4. A warm battery has much more starting capacity

than a cold battery.

5. Use fresh winter grade fuel. NOTE: Winter grade

gasoline has a higher volatility to improve starting.

Do not use gasoline left over from summer.

Starting

1. Turn fuel shut-off valve to ‘‘on’’ position. See

Figure 6.

Figure 5. Control Panel.

Figure 6. ‘‘On’’ Position of Fuel Shut-Off Valve.

2. For a Cold Engine – Place the throttle control

midway between the “slow” and “fast” positions.

See Figure 5. Place the choke control into the “on”

position.

For a Warm Engine (normal operating

temperatures) – Place the throttle control midway

between the “slow” and “fast” positions. The

choke is not required to start a warm engine.

3. Start the engine as follows:

For Retractable Start Engine – Turn engine

On/Off switch to ‘‘on’’ (see Figure 7) and SLOWLY

pull the starter handle until just past compression –

STOP! Return starter handle, pull firmly with a

smooth, steady motion to start. Pull the handle

straight out to avoid excessive rope wear from the

starter rope guide.

Figure 7. Retractable Start Engine On/Off Switch.

Extend the starting rope periodically and check its

condition. If the rope is frayed, have it replaced

immediately by your Kohler Engine Service Dealer.

Throttle

Control

Choke

Control

WARNING: Accidental Starts!

Disabling engine. Accidental starting can cause

severe injury or death. Before working on the engine

or equipment, disable the engine as follows: 1)

Disconnect the spark plug lead(s). 2) Disconnect

negative (-) battery cable from battery.

For an Electric Start Engine – Activate the

starter switch. Release the switch as soon as the

engine starts.

Stopping

1. If possible, remove the load.

2. Move the throttle control to the “slow” or “low”

idle position. Allow the engine to run at idle for

30-60 seconds.

3. Move the throttle control to the “slow” position.

Turn key switch or on/off switch to ‘‘off’’ position.

4. Close fuel shut-off valve.

Battery

A 12 volt battery is normally used. Refer to the

operating instructions of the equipment this engine

powers for specific battery requirements.

If the battery charge is not sufficient to crank the

engine, recharge the battery (see page 12).

Operating

Angle of Operation

This engine will operate continuously at angles up

to 20°. Check oil level to assure crankcase oil is up to

the point of overfilling the filler neck.

Refer to the operating instructions of the equipment

this engine powers. Because of equipment design or

application, there may be more stringent restrictions

regarding the angle of operation.

NOTE: Do not operate this engine continuously at

angles exceeding 20° in any direction. Engine

damage could result from insufficient

lubrication.

Cooling

NOTE: If debris builds up on the grass screen or

other cooling air intake areas, stop the engine

immediately and clean. Operating the engine

with blocked or dirty air intake and cooling

areas can cause extensive damage due to

overheating.

WARNING: Hot Parts!

Engine components can get extremely hot from

operation. To prevent severe burns, do not touch these

areas while the engine is running–or immediately after

it is turned off. Never operate the engine with heat

shields or guards removed.

Engine Speed

NOTE: Do not tamper with the governor setting to

increase the maximum engine speed.

Overspeed is hazardous and will void the

engine warranty.

Figure 8. Electric Start Engine Starter Switch.

NOTE: Do not crank the engine continuously for

more than 10 seconds at a time. If the

engine does not start, allow a 60 second

cool down period between starting

attempts. Failure to follow these

guidelines can burn out the starter motor.

NOTE: If the engine develops sufficient speed to

disengage the starter but does not keep

running (a false start), the engine rotation

must be allowed to come to a complete

stop before attempting to restart the

engine. If the start is engaged while the

flywheel is rotating, the starter pinion and

flywheel ring gear may clash, resulting in

damage to the starter.

If the starter does not turn the engine over, shut off

starter immediately. Do not make further attempts to

start the engine until the condition is corrected. Do not

jump start using another battery (refer to "Battery").

See your Kohler Engine Service Dealer for trouble

analysis.

4. For a Cold Engine – Gradually return the choke

control to the “off” position after the engine starts

and warms up.

The engine/equipment may be operated during the

warm up period, but it may be necessary to leave

the choke partially on until the engine warms up.

Off

Start

Maintenance Instructions

Maintenance, repair, or replacement of the emission control devices and systems, which are being done

at the customers expense, may be performed by any non-road engine repair establishment or individual.

Warranty repairs must be performed by an authorized Kohler service outlet.

WARNING: Accidental Starts!

Disabling engine. Accidental starting can cause severe injury or death. Before working on the engine or

equipment, disable the engine as follows: 1) Disconnect the spark plug lead(s). 2) Disconnect negative (-) battery

cable from battery.

Maintenance Schedule

These required maintenance procedures should be performed at the frequency stated in the table. They should

also be included as part of any seasonal tune-up.

Daily or Before

Starting Engine

Maintenance RequiredFrequency

• Fill fuel tank.

• Check oil level.

• Check air cleaner for dirty, loose, or damaged parts.

• Check air intake and cooling areas, clean as necessary.

• Check fuel hose for cracks or damage. Replace if necessary.

• Check exhaust system for leakage. Retighten or replace gasket if necessary.

• Check choke operation.

• Check retractable starter operation.

• Service precleaner element. Replace if necessary.

Every 25 Hours

Check Oil Level

The importance of checking and maintaining the proper

oil level in the crankcase cannot be overemphasized.

Check oil BEFORE EACH USE as follows:

1. Make sure the engine is stopped, level, and is

cool so the oil has had time to drain into the sump.

2. To keep dirt, debris, etc., out of the engine, clean

the area around the oil fill/check plug before

removing it.

3. Unthread and remove the oil fill/check plug.

4. The level should be up to but not over, the point of

overflowing the filler neck.

¹Perform these maintenance procedures more frequently under extremely dusty, dirty conditions.

²Have a Kohler Engine Service Dealer perform this service.

• Change oil.

• Replace air cleaner element.

• Remove cooling shrouds and clean cooling areas.

• Check all fittings and fasteners.

• Clean fuel valve shut-off filter. Replace if necessary.

• Check muffler screen/spark arrestor. Clean/replace if necessary.

• Check spark plug condition, adjust gap, and clean. Replace if necessary.

Every 100 Hours

• Check and adjust valve clearance when engine is cold.

• Check and adjust idle speed.

• Service starter motor drive, if so equipped.

• Check cooling fan for damage.

• Have combustion chamber decarbonized.

Annually or

Every 300 Hours

Figure 9. Location of Oil Drain and Check Plugs.

Oil Fill/

Check Plug

Oil Drain Plug

NOTE: If the engine stalls or does not start, turn the

engine switch to ‘‘on’’ position and then pull

the recoil starter or attempt to start engine. If

the oil warning light flickers for a few seconds,

the engine oil is insufficient. Add oil and

restart.

NOTE: Make sure the oil level is checked BEFORE

EACH USE and is maintained up to the point

of overflowing the filler neck.

Change Oil

For a new engine, change oil after the first 20 hours

of operation. Thereafter, change oil after every 100

hours of operation.

For an overhauled engine, use 10W-30 – weight

service class SG, SH, SJ or higher oil for the first 20

hours of operation. Change the oil after this initial run-

in period. Refill with service class SG, SH, SJ or higher

oil as specified in the “Viscosity Grades” table (Figure

2) on page 4.

Change the oil while the engine is still warm. The oil will

flow freely and carry away more impurities. Make sure

the engine is level when filling, checking, or changing

the oil.

Change the oil as follows (see Figure 9):

1. To keep dirt, debris, etc., out of the engine, clean

the area around the oil fill cap/dipstick before

removing it.

2. Remove the oil drain plug and oil fill/check plug.

Be sure to allow ample time for complete

drainage.

3. Reinstall the drain plug. Make sure it is tightened

to 17.6 N·m (13 ft. lb.) torque.

4. Fill the crankcase, with new oil of the proper type,

up to the point of overflowing the filler neck. Refer

to “Oil Type” on page 4. Always check the level

before adding more oil.

5. Reinstall the oil fill/check plug and tighten securely.

NOTE: To prevent extensive engine wear or

damage, always maintain the proper oil

level in the crankcase. Never operate the

engine with the oil level below the point of

overflowing the filler neck.

NOTE: Just because you can see oil in the crankcase

doesn't mean the level is in the safe range.

Bring the level up to the point of overflowing

the filler neck.

Figure 10. Proper Oil Level.

5. If the level is low, add oil of the proper type, up to

the point of overflowing the filler neck. (Refer to

“Oil Type” on page 4.) Always check the level

before adding more oil.

NOTE: To prevent extensive engine wear or

damage, always maintain the proper oil

level in the crankcase. Never operate the

engine with the oil level below the point of

overflowing the filler neck.

Oil Sentry™

Engines are equipped with an Oil Sentry™ oil monitor.

When the oil level falls below the safe level, the engine

stops automatically. Unless you refill with oil, the

engine will not start again. See Figure 11.

Figure 11.

Filler Neck

Bring Level Up To

Point of Overflow

(Cutaway Showing

Proper Oil Level)

Reduction Systems

2:1 Reduction Systems

All 2:1 reduction systems are lubricated by the

crankcase oil of the engine through special openings in

the closure plate. No special maintenance or service is

necessary. Check and maintain the oil level as outlined

on pages 8 and 9.

6:1 Reduction Systems

CS4 and CS6: Use an internal pinion and ring gear

system, independent of, and separated from the main

crankcase lubrication. See Figure 12. Use the same

weight oil in the reduction system that is being used in

the crankcase. Reduction System Capacity = .15

liters (5.07 fl. oz.). Change the reduction system oil

every 300 hours as follows:

1. Drain old oil out through the oil level/drain plug, tip

engine as required.

2. Engine must be level. Fill with new oil through the

oil fill plug hole on top until the oil level is up to the

bottom of the oil level/drain plug hole. Reinstall

both plugs securely.

NOTE: Operating the engine with loose or damaged air

cleaner components could allow unfiltered air

into the engine causing premature wear and

failure.

Service Precleaner

Wash and reoil the precleaner every 25 hours of

operation (more often under extremely dusty or dirty

conditions).

1. Remove the outer cover of the air cleaner

assembly and access the element.

2. Remove the precleaner from the paper element.

3. Wash the precleaner in warm water with

detergent. Rinse the precleaner thoroughly until all

traces of detergent are eliminated. Squeeze out

excess water (do not wring). Allow the precleaner

to air dry.

4. Saturate the precleaner with new engine oil and

squeeze out all excess oil.

5. Reinstall the precleaner over the paper element.

6. Reinstall and secure the air cleaner cover.

Service Paper Element

Every 100 hours of operation (more often under

extremely dusty or dirty conditions), replace the paper

element.

1. Remove the outer cover of the air cleaner

assembly and access the element/precleaner

assembly. Remove the wing nut securing the

element assembly, or pull the complete assembly

out of the cover/housing (some Heavy Duty Air

Cleaners). Separate the precleaner from the

element and service as outlined above.

2. Do not wash the paper element or use pressurized

air, as this will damage the element. Replace a

dirty, bent, or damaged element with a genuine

Kohler element. Handle new elements carefully;

do not use if the sealing surfaces are bent or

damaged.

3. When servicing the air cleaner, check the air

cleaner base. Make sure it is secured and not

bent or damaged. Check the air cleaner cover/

housing for damage or improper fit. Replace all

bent or damaged air cleaner components.

On Standard Air Cleaner Systems:

Before air cleaner is reassembled make sure

rubber seal is in position around stud. Inspect seal

and replace if its condition is questionable in any

way.

Figure 12. CS4 and CS6 6:1 Reduction System.

CS8.5, CS10, and CS12: Use a gear reduction system

which is lubricated by the crankcase oil of the engine

through holes in the closure plate. No special

maintenance or service is necessary.

Service Precleaner and Air Cleaner Element

This engine is equipped with a replaceable, high

density paper air cleaner element. All engines are also

equipped with an oiled, foam precleaner which covers

the paper element. See Figure 13 on page 11.

Check the air cleaner daily or before starting the

engine. Check for a buildup of dirt and debris around

the air cleaner system. Keep this area clean. Also

check for loose or damaged components. Replace all

bent or damaged air cleaner components.

Oil Fill Plug

Oil Level/Drain Plug

On Heavy Duty Air Cleaner Systems:

Remove and clean the lower dirt/swirl chamber.

Make sure the openings near the base of

chamber and in the air cleaner cover/housing, are

not blocked or restricted. See Figure 13.

4. Position the paper element on base and secure

with wing nut, then install the precleaner over the

element. If element is not secured with a wing nut,

place the precleaner over the element and install it

as an assembly into the cover/housing. Narrow

end must be installed first and face away the from

base.

5. Reinstall and secure the outer cover/housing.

Clean Air Intake/Cooling Areas

To ensure proper cooling, make sure the grass screen,

cooling fins, and other external surfaces of the engine

are kept clean at all times.

Every100 hours of operation (more often under

extremely dusty, dirty conditions), remove the blower

housing and other cooling shrouds. Clean the cooling

fins and external surfaces as necessary. Make sure the

cooling shrouds are reinstalled.

NOTE: Operating the engine with a blocked grass

screen, dirty or plugged cooling fins, and/or

cooling shrouds removed, will cause engine

damage due to overheating.

Ignition System

This engine is equipped with a dependable electronic

magneto ignition system. Other than periodically

checking/replacing the spark plug, no maintenance,

timing, or adjustments are necessary or possible with

this system.

In the event starting problems should occur which are

not corrected by replacing the spark plug, see your

Kohler Engine Service Dealer for trouble analysis.

Knob

Air Cleaner

Cover

Seal

Wing Nut

Precleaner

Air Cleaner

Element

Heavy Duty Air Cleaner System

Standard Dual Air Cleaner System

Openings must not be

blocked or restricted

Element

Precleaner

Air Cleaner

Cover/

Housing

Latches

Lower Swirl/Dirt

Chamber

Figure 13. Air Cleaner System Components.

Check Spark Plug

Annually or every 100 hours of operation, remove the

spark plug, check condition, and reset the gap or

replace with new plug as necessary. The original plug

is an NGK BPR4ES. The Champion

equivalent of that

NGK plug is RN14YC. The service replacement is

Champion

RC14YC (Kohler part No. 66 132 01-S).

Equivalent alternate brand plugs can also be used.

1. Before removing the spark plug, clean the area

around the base of the plug to keep dirt and debris

out of the engine.

2. Remove the plug and check its condition.

Replace the plug if worn or reuse is questionable.

NOTE: Do not clean the spark plug in a machine

using abrasive grit. Some grit could

remain in the spark plug and enter the

engine causing extensive wear and

damage.

3. Check the gap using a wire feeler gauge. Adjust

the gap to 0.76 mm (0.030 in.) by carefully

bending the ground electrode. See Figure 14.

4. Reinstall the spark plug into the cylinder head.

Torque the spark plug to 20 N·m (14 ft. lb.).

Ground

Electrode

Spark Plug

0.76 mm

(0.030 in.) Gap

Wire Gauge

Battery Charging

WARNING: Explosive Gas!

Batteries produce explosive hydrogen gas while being

charged. To prevent a fire or explosion, charge

batteries only in well ventilated areas. Keep sparks,

open flames, and other sources of ignition away from

the battery at all times. Keep batteries out of the reach

of children. Remove all jewelry when servicing

batteries.

Before disconnecting the negative (-) ground cable,

make sure all switches are OFF. If ON, a spark will

occur at the ground cable terminal which could cause

an explosion if hydrogen gas or gasoline vapors are

present.

NOTE: Do not apply 12 volt DC to kill terminal of

ignition module.

Fuel Valve

Engines are equipped with a fuel valve and integral

screen filter located at the outlet of the fuel tank. See

Figure 15. It controls and filters fuel flow from the tank

to the carburetor.

Every 100 hours of operation clean filter screen and

cup of any accumulated debris as follows:

CAUTION!

Never use or be near fuel or solvent while smoking or

in the vicinity of an open flame.

1. Stop the engine.

2. Turn the fuel valve lever to ‘‘off.’’

3. Remove the fuel valve cup and gasket.

4. Clean the cup with solvent and wipe it off.

5. Check the gasket, replace if damaged.

6. Reinstall the gasket and fuel valve cup.

CAUTION!

Be sure the fuel valve cup is tightened securely.

Figure 14. Servicing Spark Plug.

Figure 15.

Fuel Tank Filter

A serviceable fuel tank filter is located under the fuel

tank cap, in the filler neck.

Daily or as required clean filter of any accumulation

as follows:

1. Remove the fuel tank cap and filter.

2. Clean the filter with solvent, replace if damaged.

3. Wipe the filter and insert it.

CAUTION!

Be sure the tank cap is tightened securely.

Figure 16.

Muffler Screen and Spark Arrestor

Engines are equipped with a muffler screen and spark

arrestor for operational and environmental safety. One

of two configurations will be used, determined by the

engine model involved.

Every 100 hours of operation, remove and clean or

replace the muffler screen and/or spark arrestor

following the instructions below.

Muffler Screen CS4,CS6

CAUTION!

The engine and muffler will be very hot after the engine

has been run.

Avoid touching the engine and muffler while they are

still hot, with any part of your body or clothing.

1. Remove the muffler screen.

2. Clean the carbon deposits out of the muffler

screen using a wire brush.

3. Check the muffler screen, replace if damaged.

4. Install the muffler screen.

Figure 17. Muffler Screen.

Idle Fuel

Needle

Idle Speed

Screw

Muffler Screen and Spark Arrestor CS8.5,CS10,CS12

CAUTION!

The engine and muffler will be very hot after the engine

has been run. Avoid touching the engine and muffler

while they are still hot, with any part of your body or

clothing.

1. Remove the muffler screen.

2. Remove the spark arrestor using a flatblade

screwdriver.

3. Clean the carbon deposits out of the muffler

screen and spark arrestor using a wire brush.

CAUTION!

When cleaning, use the wire brush lightly to avoid

damaging or scratching of the muffler screen and

spark arrestor.

4. Check the muffler screen and spark arrestor,

replace if damaged.

5. Install the spark arrestor and muffler screen.

Figure 18. Muffler Screen and Spark Arrestor.

Carburetor Troubleshooting and

Adjustments

NOTE: Carburetor adjustments should be made only

after the engine has warmed up.

The carburetor is designed to deliver the correct

fuel-to-air mixture to the engine under all operating

conditions. The high idle mixture is set at the factory

and cannot be adjusted. The low idle fuel adjusting

needle is also set at the factory and has a limiting cap.

It normally does not need adjustment.

If the engine is hard to start, runs roughly, or stalls at

low idle speed, it may be necessary to adjust or

service the carburetor.

Figure 19. Carburetor.

Troubleshooting

If engine troubles are experienced that appear to be

fuel system related, check the following areas before

adjusting the carburetor.

• Make sure the fuel tank is filled with clean, fresh

gasoline.

• Make sure the fuel tank cap vent is not blocked

and that it is operating properly.

• Make sure the fuel shut-off valve is fully open.

• Make sure fuel shut-off valve strainer, and in-line

fuel filter (if used) are clean and unobstructed.

Clean or replace as necessary.

Troubleshooting

When troubles occur, be sure to check the simple causes which, at first, may seem too obvious to be considered.

For example, a starting problem could be caused by an empty fuel tank. Some common causes of engine troubles

are listed in the following table.

Do not attempt to service or replace major engine components, or any items that require special timing or

adjustment procedures. Have your Kohler Engine Service Dealer do this work.

Possible Cause No Improper Dirt In Dirty Incorrect Engine Dirty Air Faulty

Problem Fuel Fuel Fuel Line Grass Screen Oil Level Overloaded Cleaner Spark Plug

Will Not Start • • ••••

Hard Starting •• • • • •

Stops Suddenly • •••••

Lacks Power •••••••

Operates Erratically ••• • ••

Knocks or Pings •• • •

Skips or Misfires ••• ••

Backfires ••••

Overheats •••••

High Fuel Consumption ••

• Make sure fuel is reaching the carburetor. This

includes checking the fuel lines and components

for restrictions or problems. Replace as

necessary.

• Make sure On-Off switch is functioning properly.

• Make sure the air cleaner element is clean and all

air cleaner components are fastened securely.

If, after checking the items listed above, the engine is

hard to start, runs roughly, or stalls at low idle speed, it

may be necessary to adjust or service the carburetor.

Adjust Carburetor

NOTE: Certified engines have a limiter cap on the idle

fuel adjusting needle. Adjustment can only be

performed within the limits allowed by the cap.

1. Start the engine and run at half throttle for 5 to 10

minutes to warm up. The engine must be warm

before making final settings.

2. Low Idle Fuel Needle Setting: Place the throttle

into the ‘‘idle’’ or ‘‘slow’’ position. Turn the low

idle fuel adjusting needle/cap in or out within

adjustment range, to obtain the best low speed

performance.

3. Low Idle Speed Setting: Place the throttle control

into the ‘‘idle’’ or ‘‘slow’’ position. Set the low idle

speed to 2000 RPM* (+ 150 RPM) by turning the

low idle speed adjusting screw in or out. Check

the speed using a tachometer.

*NOTE: The actual low idle speed depends on the

application – refer to equipment

manufacturer's recommendations. The

recommended low isle speed for basic

engines is 2000 RPM. To ensure best

results when setting the low idle fuel

needle, the low idle speed must not

exceed 2000 RPM (+ 150 RPM).

Storage

If the engine will be out of service for two months or

more, use the following storage procedure:

1. Clean the exterior surfaces of the engine.

2. Change the oil while the engine is still warm from

operation. See “Change Oil” on page 9.

3. The fuel system must be completely emptied, or

the gasoline must be treated with a stabilizer to

prevent deterioration. If you choose to use a

stabilizer, follow the manufacturers

recommendations, and add the correct amount for

the capacity of the fuel system. Fill the fuel tank

with clean, fresh gasoline. Run the engine for 2-3

minutes to get stabilized fuel into the carburetor.

To empty the system, run the engine until the tank

and system are empty.

4. Remove the spark plug. Add one tablespoon of

engine oil into the spark plug hole. Install the plug,

but do not connect the plug lead. Crank the engine

two or three revolutions.

5. Remove the spark plug. Cover the spark plug hole

with your thumb, and turn the engine over until the

piston is at the top of its stroke. (Pressure against

the thumb is greatest.) Reinstall the plug, but do

not connect the plug lead.

6. Store the engine in a clean, dry place.

Parts Ordering

The engine Specification, Model, and Serial Numbers

are required when ordering replacement parts from

your Kohler Engine Service Dealer. These numbers are

found on the identification plate which is affixed to the

engine shrouding. Include letter suffixes if there are

any. See “Engine Identification Numbers” on page 5.

Always insist on genuine Kohler parts. All genuine

Kohler parts meet strict standards for fit, reliability, and

performance.

Major Repair

Major repair information is available in Kohler Engine

Service Manuals. However, major repair generally

requires the attention of a trained mechanic and the

use of special tools and equipment. Your Kohler

Engine Service Dealer has the facilities, training, and

genuine Kohler replacement parts necessary to

perform this service. For Sales & Service assistance

call 1-800-544-2444 (U.S. & Canada) or contact your

Kohler Engine Dealer or Service Distributor, they're in

the Yellow Pages under Engines-Gasoline.

Model Designation

Model CS4T for example: C designates Command

engine, S designates slanted cylinder configuration,

and 4 designates horsepower. A suffix letter designates

a specific version as follows:

Suffix Designates

T Retractable Start

S Electric Start

G Tapered Crankshaft

P Threaded Crankshaft

R Gear Reduction (2:1 or 6:1)

LIMITED 2 YEAR COMMAND ENGINE WARRANTY

Kohler Co. warrants to the original consumer that each new COMMAND engine sold by Kohler Co. will be free from manufacturing

defects in materials or workmanship in normal service for a period of two (2) years from date of purchase, provided it is operated and

maintained in accordance with Kohler Co.’s instructions and manuals.

Our obligation under this warranty is expressly limited, at our option, to the replacement or repair at Kohler Co., Kohler, Wisconsin 53044,

or at a service facility designated by us of such parts as inspection shall disclose to have been defective.

EXCLUSIONS:

Mufflers on engines used commercially (non-residential) are warranted for one (1) year from date of purchase, except catalytic

mufflers, which are warranted for two (2) years.

This warranty does not apply to defects caused by casualty or unreasonable use, including faulty repairs by others and failure to

provide reasonable and necessary maintenance.

The following items are not covered by this warranty:

Engine accessories such as fuel tanks, clutches, transmissions, power-drive assemblies, and batteries, unless supplied or installed by

Kohler Co. These are subject to the warranties, if any, of their manufacturers.

KOHLER CO. AND/OR THE SELLER SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF

ANY KIND, including but not limited to labor costs or transportation charges in connection with the repair or replacement of defective

parts.

IMPLIED OR STATUTORY WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. We make no other express warranty, nor is any one

authorized to make any on our behalf.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

TO OBTAIN WARRANTY SERVICE:

Purchaser must bring the engine to an authorized Kohler service facility. To locate the nearest facility, visit our website

www.kohlerengines.com, consult your Yellow Pages, or telephone 1-800-544-2444.

ENGINE DIVISION, KOHLER CO., KOHLER, WISCONSIN 53044

Specifications

Model: ..........................................................................CS4 ............. CS6 ........CS8.5 ........... CS10...........CS12 ..... CS12.75

Bore: ................................................. mm(in.) .....56(2.20) ...... 66(2.60) .... 75(2.95) .......78(3.07)...... 85(3.35) ...... 85(3.35)

Stroke: ............................................... mm(in.) ..... 50(1.97) ...... 50(1.97) .... 57(2.44) .......63(2.48)...... 63(2.48) ...... 63(2.48)

Displacement: ................................. cm

(in.

) ...123(7.51) .. 171(10.44) .. 251(15.3) ...301(18.37).. 357(21.79) ..357(21.79)

*Power (@ 3600 RPM): .................... kW(HP) ......2.98(4*) ....... 4.47(6*) ....5.4(8.5*) ..... 7.45(10*).....8.95(12*) 9.51(12.75*)

Max. Torque:.................................. N·m(ft. lb.) ...... 8.4(6.2) ......13.0(9.6) . 19.3(14.2) ....21.6(15.9) ... 27.3(20.1) ... 30.6(22.6)

@ RPM ..................................................................... 2200 ............ 2400 ..........2200 ............ 2400............2200 ........... 2400

Compression Ratio:...................................................8.3:1 ............ 8.5:1 .......... 8.3:1 ............ 8.1:1............ 8.1:1 ............8.1:1

Weight:...............................................kg(lbs.) ..17.5(38.6) ... 17.5(38.6) .... 26(57.2) ....31.9(70.5)... 31.9(70.5) ... 31.9(70.5)

Oil Capacity:...................................L(U.S. qt.) ...... 0.6(0.6) ........0.6(0.6) .... 1.0(1.06) ....... 1.1(1.2)........1.1(1.2) ....... 1.1(1.2)

Fuel Tank Capacity: .......................L(U.S. qt.) ...... 3.9(4.1) ........3.9(4.1) ..... 6.0(6.3) ........ 6.9(7.3)........6.9(7.3) ....... 6.9(7.3)

Exhaust Emission Control System: ................... EM

*Horsepower ratings exceed Society of Automotive Engineers Small Engine Test Code J1940. Actual engine

horsepower is lower and affected by, but not limited to, accessories (air cleaner, exhaust, charging, cooling, fuel

pump, etc.), application, engine speed and ambient operating conditions (temperature, humidity, and altitude).

Kohler reserves the right to change product specifications, designs, and equipment without notice and without

incurring obligation.

KOHLER CO.

FEDERAL AND CALIFORNIA EMISSION CONTROL SYSTEMS

LIMITED WARRANTY

SMALL OFF-ROAD ENGINES

The U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and Kohler Co. are pleased to explain the

Federal and California Emission Control Systems Warranty on your small off-road equipment engine. For California, engines produced in 1995

and later must be designed, built and equipped to meet the state’s stringent anti-smog standards. In other states, 1997 and later model year

engines must be designed, built and equipped to meet the U.S. EPA regulations for small non-road engines. The engine must be free from

defects in materials and workmanship which cause it to fail to conform with U.S. EPA standards for the first two years of engine use from the

date of sale to the ultimate purchaser. Kohler Co. must warrant the emission control system on the engine for the period of time listed above,

provided there has been no abuse, neglect or improper maintenance.

The emission control system may include parts such as the carburetor or fuel injection system, the ignition system, and catalytic converter.

Also included are the hoses, belts and connectors and other emission related assemblies.

Where a warrantable condition exists, Kohler Co. will repair the engine at no cost, including diagnosis (if the diagnostic work is performed at an

authorized dealer), parts and labor.

MANUFACTURER’S WARRANTY COVERAGE

Engines produced in 1995 or later are warranted for two years in California. In other states, 1997 and later model year engines are warranted for

two years. If any emission related part on the engine is defective, the part will be repaired or replaced by Kohler Co. free of charge.

OWNER’S WARRANTY RESPONSIBILITIES

(a) The engine owner is responsible for the performance of the required maintenance listed in the owner’s manual. Kohler Co. recommends

that you retain all receipts covering maintenance on the engine, But Kohler Co. cannot deny warranty solely for the lack of receipts or for

your failure to assure that all scheduled maintenance was performed.

(b) Be aware, however, that Kohler Co. may deny warranty coverage if the engine or a part has failed due to abuse, neglect, improper

maintenance or unapproved modifications.

(c) For warranty repairs, the engine must be presented to a Kohler Co. service center as soon as a problem exists. Call 1-800-544-2444 or

access our web site at: www.kohlerengines.com, for the names of the nearest service centers. The warranty repairs should be completed

in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding warranty rights and responsibilities, you should contact Kohler Co. at 1-920-457-4441 and ask for an

Engine Service representative.

COVERAGE

Kohler Co. warrants to the ultimate purchaser and each subsequent purchaser that the engine will be designed, built and equipped, at the time

of sale, to meet all applicable regulations. Kohler Co. also warrants to the initial purchaser and each subsequent purchaser, that the engine is

free from defects in materials and workmanship which cause the engine to fail to conform with applicable regulations for a period of two years.

Engines produced in 1995 or later are warranted for two years in California. For 1997 and later model years, EPA requires manufacturers to

warrant engines for two years in all other states. These warranty periods will begin on the date the engine is purchased by the initial purchaser. If

any emission related part on the engine is defective, the part will be replaced by Kohler Co. at no cost to the owner. Kohler Co. is liable for

damages to other engine components caused by the failure of a warranted part still under warranty.

Kohler Co. shall remedy warranty defects at any authorized Kohler Co. engine dealer or warranty station. Warranty repair work done at an

authorized dealer or warranty station shall be free of charge to the owner if such work determines that a warranted part is defective.

Listed below are the parts covered by the Federal and California Emission Control Systems Warranty. Some parts listed below may require

scheduled maintenance and are warranted up to the first scheduled replacement point for that part. The warranted parts are:

• Oxygen sensor (if equipped) • Ignition module(s) with high tension lead

• Intake manifold (if equipped) • Gaseous fuel regulator (if equipped)

• Exhaust manifold (if equipped) • Electronic control unit (if equipped)

• Catalytic muffler (if equipped) • Carburetor or fuel injection system

• Fuel metering valve (if equipped) • Fuel lines (if equipped)

• Spark advance module (if equipped) • Air filter, fuel filter, and spark plugs (only

• Crankcase breather to first scheduled replacement point)

Continued on next page.

LIMITATIONS

This Emission Control Systems Warranty shall not cover any of the following:

(a) repair or replacement required because of misuse or neglect, improper maintenance, repairs improperly performed or replacements not

conforming to Kohler Co. specifications that adversely affect performance and/or durability and alterations or modifications not

recommended or approved in writing by Kohler Co.,

(b) replacement of parts and other services and adjustments necessary for required maintenance at and after the first scheduled replacement

point,

(d) diagnosis and inspection fees that do not result in eligible warranty service being performed, and

(e) any add-on or modified part, or malfunction of authorized parts due to the use of add-on or modified parts.

MAINTENANCE AND REPAIR REQUIREMENTS

The owner is responsible for the proper use and maintenance of the engine. Kohler Co. recommends that all receipts and records covering the

performance of regular maintenance be retained in case questions arise. If the engine is resold during the warranty period, the maintenance

records should be transferred to each subsequent owner. Kohler Co. reserves the right to deny warranty coverage if the engine has not been

properly maintained; however, Kohler Co. may not deny warranty repairs solely because of the lack of repair maintenance or failure to keep

maintenance records.

Normal maintenance, replacement or repair of emission control devices and systems may be performed by any repair establishment or

individual; however, warranty repairs must be performed by a Kohler authorized service center. Any replacement part or service that is

equivalent in performance and durability may be used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations of

the engine manufacturer.

FOR SALES AND SERVICE INFORMATION

IN U.S. AND CANADA, CALL

1-800-544-2444

www.kohlerengines.com

ENGINE DIVISION, KOHLER CO., KOHLER, WISCONSIN 53044

FORM NO.: TP-2494

ISSUED: 8/98

REVISED: 8/05

Kohler COMMAND PRO CS Series User manual

Brand: Kohler

Model: COMMAND PRO CS Series

Category: Garden tools

Type: User manual

Download PDF

report

Kohler COMMAND PRO CS Series User manual

Kohler COMMAND PRO CS Series User manual

Related papers

Other documents