2. OMIX
  3. 11603.01

OMIX 11603.01 Installation guide

  • Hello! I've reviewed the installation instructions for the OMIX-ADA TJ Replacement Fender Flares. This document provides step-by-step guidance on how to install the replacement fender flares, including the front and rear flares, and also the flare extensions for specific models. I'm ready to answer any questions you have about the installation process or the components included.
  • What needs to be disconnected before removing the front flares?
    What is recommended to do when removing the rear flares?
    How are the front flares secured?
Copyright © 2015 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 100 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
TJ Replacement Fender Flares
Page 1/3
Part #11603.01
11603.02
11603.11
11603.12
OMIX-ADA® TECHNICAL SUPPORT
PHONE: M-F 8am - 5pm EST 1-800-449-6649 | EMAIL: [email protected]
FOR WARRANTY INFORMATION VISIT: www.Omix-Ada.com
1
3
2
4
5
6
Washer x34
Flange Head
Screw x22
T-Slot Nut x22
Hex Bolt x12
Rivet Nut x12
1. Front Flare, LH (1)
2. Front Flare, RH (1)
3. Rear Flare, LH (1)
4. Rear Flare, RH (1)
Included only with Part #11603.01 and 11603.11:
5. Flare Extension, LH (1)
6. Flare Extension, RH (1)
Components *Included only
with Part #11603.01
and 11603.12
Copyright © 2015 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 100 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
TJ Replacement Fender Flares
Page 2/3
3. Detach all hardware an remove rear ares.
Removing or pulling back rear fender
liner is recommended for this step. Shield
retainers may need to be removed.
1. Disconnect side marker lights, twisting bulb
counter-clockwise.
2. Detach all hardware and remove front ares.
4. Ensure body panels are clean before installation.
5. Install front ares by rst lining up placement pins
with body panel holes.
6. Attach using Flange-Head Screw and T-slot Nut
for front holes and Hex Bolt, Washer, and Rivet Nut (if
needed) in rear holes.
7. Fully tighten all bolts.
Copyright © 2015 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 100 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
TJ Replacement Fender Flares
Page 3/3
For Part #11603.01 and 11603.11:
11. Remove three Hex Head Washer Bolts from OE
Flare Extension.
12. Align Flare Extension with side body panel and
loosely attach with bolts.
13. Adjust front to back location of Flare Extension
to reduce gap between Replacement Flare and
Extension. Tighten all bolts.
8. Install Rear Flares using Flange-Head Screw and
T-slot Nut for front holes and Hex Bolt, Washer, and
Rivet Nut (if needed) in rear holes.
9. Tighten all bolts and replace rear fender liner.
If any shield retainers were removed
during installation, replace them now.
10. Reinstall side marker light by twisting clockwise
into casing.
/