ECILS3 & ECILS3FF
Data Projector Cart
PARTS LIST
Qty Part# Description
2 022-2479 Lower Left Front/Right Rear Legs
2 022-2480 Lower Right Front/Left Rear Legs
1 022-2473 Middle Shelf w/ Door Stop
1 010-4323 Bottom Shelf
1 010-4778 Rear Panel
2 010-4777 Side Panels
1 022-2476 Right Door with Lock
1 022-2475 Left Door
1 022-2474 Top Shelf
4 022-2836 Upper Leg Assemblies
2 010-4389 Right & Left Slide Brackets
1 010-4335 Rear Support Panel
1 010-4391 Slide Out Keyboard Shelf
1 030-1119 20” Full Extension Slide (1 Set)
2 015-0002 4” Casters w/o Lock
2 015-0003 4” Casters w/ Lock
1 E12 12 Outlet Electrical Unit
(Model ECILS3FF ONLY)
HARDWARE LIST
Ref Qty Part# Description
AA 24 030-0300 5/8” Square Head Bolts
BB 24 030-0002 5/16”-18 Serrated Nuts
CC 2 030-0023 #6-32 x 3/8” Machine Screws
DD 2 030-0522 #6-32 Hex Nuts w/ External Teeth
EE 4 030-0383 #10 x 1/2” Truss Head Screws
FF 4 030-0325 1/4-20 x 1/2” Combo Screws
GG 4 030-0291 #10-32 x 1/2” Phillips Truss Screws
HH 4 030-0357 10-32 Flanged Hex Serrated Nuts
I I 4 030-0255 #10 x 5/8” Phillips Pan Hd Screws
JJ 8 030-0302 8-32 x 3/8” Combo Truss Screws
KK 8 02236 8-32 Hex Flange Nuts
1 010-1188 Bottom Door Stop
2 012-0286 Plastic Handles
1 010-1106 Hex Wrench
TOOLS REQUIRED
Hex Wrench (Provided)
Phillips Screwdriver
Rubber Mallet (Optional)
Position the lower front legs (stamped “XX” and “YY”) with the brackets facing up
and in as shown in FIGURE 1. Slide the bottom and middle shelves onto the legs
making sure the brackets are inside of the shelves as shown in FIGURE 2.
STEP 1
1
FIGURE 2
FIGURE 1
Assembly Instructions
STEP 2
Slide the 2 remaining lower legs onto the shelves as
shown. Make sure the brackets are inside the shelves.
Slide the rear panel between the middle and bottom shelf so
that the top ange is behind the leg brackets and the bottom
hooks onto the bottom shelf. Attach in the 4 corners with bolts
(AA) and nuts (BB) as shown.
STEP 3
CAREFULLY turn the unit on its back. Attach each side panel in the same
manner as described in STEP 3 using bolts (AA) and nuts (BB) as shown.
FULLY TIGHTEN BOTTOM SHELF HARDWARE ONLY. LEAVE MIDDLE
SHELF HARDWARE LOSE AT THIS TIME.
STEP 4
2
AA BB
3
Push casters into the sockets of each leg. To ensure
casters are secure in sockets, a rubber mallet may
be used to tap casters in place.
STEP 5 STEP 6
Attach door stop to bottom shelf using screws (CC) and
nuts (DD). CAREFULLY stand unit upright.
STEP 7 STEP 8
Attach the door handles using screws (EE). Attach the doors (right one has lock) between the middle and
bottom shelves with screws (FF) as shown. NOTE: Adjustments
to the door stop may need to be done.
CC DD
EE FF
4
STEP 9
Lay the top shelf down and install the upper legs in each corner as shown in FIGURE 3.
Slide the right and left slide brackets between the legs as shown in FIGURE 4. The slides
face inward and the 2 holes face the back edge. Then LOOSELY attach legs and brackets
to top shelf using bolt (AA) and nuts (BB) as shown in FIGURE 5.
FIGURE 3
FIGURE 4
Back Edge Holes
FIGURE 5
LOOSELY attach in each corner
5
STEP 10
STEP 11
I I
GG HH
Slide rear support panel between the slide brackets as shown in FIGURE 6.
Secure to brackets with screws (GG) and nuts (HH) as shown in FIGURE 7.
FIGURE 6
FIGURE 7
FIGURE 8 FIGURE 9
Carefully turn top shelf assembly over and place it onto the bottom section of the cart as shown
in FIGURE 8. TIGHTEN ALL SHELF HARDWARE AT THIS TIME. Raise the top shelf section
to desired height and secure in place with screws (I I) as shown in FIGURE 9.
Separate each slide and attach outer slide piece (2 per bracket) to
the slide brackets using screws (JJ) and nuts (KK) as shown. NOTE:
Slide may need to be extended some to align attachment holes.
NOTE: Separate slides
by pulling on black tab.
STEP 12
Attach inner slide piece to keyboard shelf with screws (JJ) and nuts (KK).
STEP 13
6
JJ KK
JJ
KK
KK
JJ Attach rear
screw & nut
FIRST
You may need
to slide out
inner slide to
access hole.
7
Part # 031-5439
Rev. 06.18.10 CZ
STEP 14
Slide keyboard shelf onto slide brackets.
/
