Eurolux F74W Owner's manual

Brand: Eurolux

Model: F74W

Type: Owner's manual

3 Blade Fans

MODEL

F74W

PRODUCT CODE

Cape Town - 9 Racecourse Road, Milnerton, 7441

Johannesburg - 10 Milkyway Avenue, Linbro Business Park, Sandton, 2065

web: www.eurolux.co.za

Please read instructions before commencing installation and retain for

future reference.

F74: Excluding 2 x E14 40W 230V

ILLUSTRATION

Waste electrical & Electronic equipment regulations requires that any of our products

showing this marking must not be disposed of with other household or commercial

waste. To prevent possible harm to the environment or human health from uncontrolled

waste disposal, please separate any such products from other waste types and

recycle it responsibly at your local facilities.

ENVIRONMENTAL PROTECTION

Description Of Parts:

1. Mounting bracket

2. Screw

3. Screw

4. Hanger ball

5. Upper Canopy

6. Downrod

7. Lower canopy

8. Screw

9. Upper housing

10. Screw

11. Cross pin

12. Downrod Yoke

13. Cotter pin

14. Screw

15. Blade

16. Motor

17. Light plate

18. Lampholder

19. Glass

20. Male and female plug/

quick connector

21. Remote control receiver

22. Male and female plug/

quick connector

23. Male and female plug/

quick connector

24. Male and female plug/

quick connector

25. Remote control

CAUTION: Ensure power supply is turned o before attempting trouble shooting.

NOTE: This fan does not contain servicable parts. DO NOT OPEN or TAMPER WITH THE MOTOR.

Should your fan not start:

1) Check fuses are in place in the switchboard.

2) Recheck the terminal strip connections.

3) Ensure the wall & direction switches are not stuck in a “middle” position.

4) Ensure that the shipping tabs have been removed.

5) Ensure that the speed controller is not in the incorrect position.

Should your fan be noisy:

1) Check all screws are suciently tight: fan blades and fan holders, (if applicable) glass of the

lamp holder.

2) Allow at least 24 hours for the fan to settle.

Should your fan wobble:

In general, wobble is caused by the blades not cutting the air at the same point. Measure downwards

from the ceiling and make sure each blade is at the same height to the ceiling. See Figure 1. If they are

not, adjust by hand by slightly bending the blade and bracket. If a major adjustment is needed, insert a

washer as shown in Figure 2.

1) Check the blades are securely fastened to the holders.

2) Check the blade holders are tight on the motor.

3) Ensure the mounting bracket is properly screwed to the ceiling.

4) Interchange opposite blade sets if needed.

• Fitting material: Pressed steel & ABS

• Lens: Frosted Glass

• Lamp: Excluding 2 x E14 40W 230V

• Dimensions: (H)370mm x (Ø)1330mm

• Motor: 28W

• Voltage: 220V - 240V ~ 50Hz

• Protection against electric shock: Class 1. Requires earth connection.

• IP: 20. Protected against solid foreign objects of 12.5mm Ø and greater, not protected against water.

• Not for outdoor use or in wet conditions and areas of high humidity.

• Features: 5 Speeds forward and reverse.

Remote compatible (Remote included).

• 2 year warranty

SPECIFICATIONS

F74W - attachments:

If the external exible cable or cord of this fan is damaged, it should be exclusively replaced by the

manufacturer or his service agent or a similar qualied person in order to avoid a hazard.To ensure that

you get maximum longevity and maximum use out of your fan, please observe the following

safety instructions.

Electrical products can cause death, injury, or damage to property.

Installation of the fan must be carried out by a qualied electrician, in accordance with SANS 10142.

On completion of installation, ensure that the Certicate of Compliance is updated.

• Before connecting this fan, ensure that voltage indicated on the rating label corresponds with the mains

voltage in your home.

• When cleaning, ensure that the power is turned o.

• This fan is checked in full for conformity to the quality standards and safety requirements.

• The manufacturer / supplier is not responsible for any damage of properties and persons, caused by

the incorrect use or installation of the fan.

• Should you be unsure of how to install this fan correctly, please consult a professional electrician or

your supplier for assistance.

• Ensure all items/ components, threads and screws are tightly secured.

IMPORTANT:

• Tampering with this fan, I.E. Using silicon sealers or incorrect cabling, will invalidate your warranty.

• Please check whether the connection of the power cord is safe and reliable before installation.

• Always ensure that the mains supply voltage is correct.

• Do not use the fan outdoors, in wet conditions or areas of high humidity.

• Do not insert objects or ngers through the bars of the grill.

• This appliance is not intended for use by young children or inrm persons unless they have been

adequately supervised by a responsible person.

IMPORTANT SAFEGUARDS

TROUBLE SHOOTING:

Touching

Ceiling

Figure 1

Fan Wobbles:

CLEANING

• Before cleaning always ensure the power supply is turned o and that the fan has been unplugged.

• Do not immerse the fan in water.

• No abrasive products, solvents, detergent may be used to clean this fan.

• Ensure that the fan does not come in contact with corrosive chemicals, etc.

• Remove the front grill guard, blades and rear grill guard and wipe down parts with a damp cloth to

remove any dust.

• Ensure all parts are dry before reassembling your fan.

• The motor bearings are permanently sealed and do not require additional lubrication.

OPERATION INSTALLATION

Secure the Mounting bracket to the ceiling

joist with the two long fixing screws provided Loosen the motor screw. Install the Blades, fastening with screw.

Loosen the cross pin and cotter pin from the

downrod.

Insert the upper canopy and lower canopy to

the downrod

Insert the hanger ball to downrod Insert the cross pin and lock the hanger ball and

downrod screw.

Insert the downrod to yoke and then insert

the cross pin and cotter pin to tighten the

yoke screw to fix the downrod.

7 8 9

4 5 6

1 2 3

Loosing the screw from the hanger ball

INSTALLATION

Tighten screws on the downrod yoke plate Tighten screws on the upper housing

Wire the incoming power cables to the

terminal block mounted on the

Mounting bracket. Wire 12 Neutral, Earth,

Active to the corresponding N,L,

terminals respectively.

Slide the canopy up to cover the ball joint

wiring receiver and hanging bracket, then

secure in place.

The remote receiver has been ore-wired to the

mounting bracket. Do not remove.

Connect the quick-connectors between the

remote control receiver and the motor.

Slide the remote control receiver inside the

mounting bracket and carefully position all

excess cable inside upper canopy

13 14 15

ht woN

Put the glass, and turn clockwise direction to

lock it.

Install the light bulb (E14, Max 40W) e fan is completed.

16 17 18

10 11 12

INSTALLATION

Eurolux F74W Owner's manual

Eurolux F74W Owner's manual

Eurolux F74W Owner's manual

Related papers

Other documents