2. Computers & electronics
  3. Computer components
  4. Chassis components
  5. Computer cooling components
  6. Hardware cooling accessories
  7. ekwb
  8. EK-FC Link BLANK Parallel CSQ

ekwb EK-FC Link BLANK Parallel CSQ Installation guide

  • Hello! I've reviewed the installation and mounting manual for the EKWB FC Link BLANK Parallel CSQ and EK-FC Bridge Dual Parallel CSQ. This document provides crucial information on how to correctly install the FC Link to close unused ports on the EK-FC Bridge, highlighting the importance of properly placing the O-rings and using the correct screw. I'm ready to answer any questions you have about these components or the installation process.
  • What is the purpose of the EK-FC Link BLANK Parallel CSQ?
    Can the EK-FC Link BLANK Parallel CSQ be replaced?
    What screw is used to attach the FC Link to the EK-FC Bridge?
    What is important regarding the o-rings during installation?
All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Released on 19th of July, 2012.
Installation and mounting manual for EK-FC Link BLANK Parallel CSQ
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates. Before
installation of this product please read important notice, disclosure and warranty conditions published on www.ekwb.com .
STEP 1: PREPARING YOUR HARDWARE STEP 2: ATTACHING FC Link to the EK-FC Bridge (CSQ)
EK-FC Link BLANK parallel is a product ment to close the
unused ports on any of EK-FC Bridge Parallel CSQ products.
However, it may be replaced by an adequate EK-FC CSQ
waterblock once user acquires or decides to upgrade the
system.
Below is sample picture of EK-FC Bridge Dual Parallel CSQ. Please do not forget to secure orings
in the Bridge's groove. Make sure they are set properly and not pinched in any way. If that
condition is not met a leak may occur. A M4x25 DIN7984 screw is enclosed to EK-FC Bridge.
All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Released on 19th of July, 2012.
Installation and mounting manual for EK-FC Link BLANK Parallel CSQ
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates. Before
installation of this product please read important notice, disclosure and warranty conditions published on www.ekwb.com .
STEP 1: PREPARING YOUR HARDWARE STEP 2: ATTACHING FC Link to the EK-FC Bridge (CSQ)
EK-FC Link BLANK parallel is a product ment to close the
unused ports on any of EK-FC Bridge Parallel CSQ products.
However, it may be replaced by an adequate EK-FC CSQ
waterblock once user acquires or decides to upgrade the
system.
Below is sample picture of EK-FC Bridge Dual Parallel CSQ. Please do not forget to secure orings
in the Bridge's groove. Make sure they are set properly and not pinched in any way. If that
condition is not met a leak may occur. A M4x25 DIN7984 screw is enclosed to EK-FC Bridge.
EK-Bridge CSQ
FC Link Blank Parallel
Screw M4x25 DIN7984
EK-Bridge CSQ
FC Link Blank Parallel
Screw M4x25 DIN7984
/