Page is loading ...
The Experts in Small Printer Solutions
Ap1310-BTi
Thermal Printer
Quick Start Guide
Able Systems Limited Denton Drive, Northwich, Cheshire CW9 7TU England
Tel: +44 (0) 1606 48621 Fax: +44 (0) 1606 44903 Web: www.able-systems.com
What’s in the box?
1
2
3
4
1
2
3
4
●
Bluetooth Printer (Ap1300BTi or Ap1310BTi) x1
●
Roll of 35mm or 55mm Diameter Thermal Paper x2
●
Universal Input Trickle Charger (UK/Euro/USA/AU-NZ) x1
●
Belt Mounting Kit x1
●
Quick Start Guide x1
1
2
3
1
2
3
Setting up
Connecting the Battery Pack
For safety, the Battery Pack is supplied discharged and disconnected.
Before use, the Battery must be connected and fully charged.
Remove the screw from the Battery Compartment Door.
Push down, and slide back the Battery Compartment Door.
Fit the Battery Pack Connector taking care to insert it correctly.
Fit the Battery Pack ensuring wires are correctly routed and not trapped.
Connecting the AC Battery Charger
Plug the AC Battery Charger into a suitable Mains Outlet Socket and Insert the Jack Plug into the Power
Connector at the rear of the Printer. When connected by Bluetooth to another device, the blue LED light
There is also the option of charging the Printer via the Jack Socket in the D9 Connector.
Fully charging the Battery Pack takes about 15 hours. The printer should not be used during
this time.
Loading Paper
Slide the Lid Release Button forwards until the Lid springs open.
Unwind a small amount of paper from the roll and Insert the Paper Roll into the Printer.
Close the Lid down, and the paper is loaded.
Pressing the paper feed button when the printer is idle advances paper at typically
50mm per second, depending on the battery voltage. However, the feed
button has several additional functions:
A single press and release of the button:
●
In idle or spooling mode, advances paper.
●
In sleep mode, wakes up the printer into idle mode.
“Double-clicking” the button:
●
encoded calibration data, and the full character set.
●
In spooling mode, exits spooling mode and prints any stored data.
Using your Bluetooth printer
The Ap1300 and Ap1310 are operationally identical.
LED patterns indicate the following modes:
●
Constant GREEN: operating normally from battery pack.
●
●
ORANGE: battery is being charged.
●
RED: battery is low, or other problem.
●
The LED patterns will change when connected to another device via Bluetooth.
All GREEN will be replaced by BLUE.
All ORANGE will be replaced by PURPLE.
Accessories
Charging
LED Flashes Blue/Violet
Whilst connected to a trickle charger, the unit
can both receive and print data. Leaving a trickle
charger connected to the Ap13x0BTi will permit
the unit’s battery pack to be charged when the
unit is not printing.
A full charge takes 10-16 hours. When
charged, the printer should be unplugged
from the charger.
●
Universal Input Trickle Charger (UK/Euro/USA/AU-NZ).
Product Code: BC1300V2
●
Cigarette Lighter Vehicle Battery Charger
Product Code: BC1300CLAH
●
35mm Diameter Thermal Paper Roll (Approx. 13m long).
Product Code: A05836TPR1
●
55mm Diameter Thermal Paper Roll (Approx. 34m long).
Product Code: A05856TPR1
●
RS-232 D9 to RJ12 Data Cable.
Product Code: AP1300-D9
●
Replacement / Spare Battery Pack .
Product Code: Ap1300-BP01
●
Removable linerless label kit for Ap1300 models. 12 rolls /box; approx. 12.2 metres per roll
Product Code: A05836RLRV2KIT
●
Removable linerless label kit for Ap1310 models. 8 rolls /box; approx. 24.4 metres per roll
Product Code: A05855RLRKIT
Connecting to Mobile devices
To connect to your iPod, iPhone or iPad device, follow these steps:
Ensure the printer is awake
On your mobile device’s settings app, enable Bluetooth and
connect to the printer marked “Able Ap13x0-BTi”
When prompted, enter the PIN “1234”
Your mobile device will now be connected to your
mini-printer and ready to print
1
2
3
4
Tech Spec
Product Colour Code
Bluetooth Printer
TM
(35mm diam. roll) White Ap1300-BTi
Bluetooth Printer
TM
(55mm diam. roll) White AP1310-BTi
(All models include rechargeable battery pack)
Print Mode: Thermal Line Dot Print (8 dots/mm)
Interface Details: RS-232 Rx, Tx, Busy, Ground, Wake-up control, Optional Trickle Charger Input..
Selectable baud rates and formats. (Default: 9600,N,8,1) Serial Data Cable available
Bluetooth: Full Bluetooth Support Bluetooth V2.1 (up to 10m range)
Battery Pack: 5 Cell NiMH Battery Pack (1.8Ah capacity) Ap1300-BP01
Charger: Universal Input Trickle Charger (UK/Euro/USA/AU-NZ) BC1300V2
Input: 100-240V 50-60Hz Auto Switching
Print Speed: 50 mm/s. Typical with a fully charged battery
Thermal Paper: Paper Width = 58mm Paper Width
Printer Life: 10
8
print pulses or 50kms of Paper (more than 13 million print lines = 3500 Paper Rolls)
Printer Dimensions: Ap1300BTi Ap1310BTi
56 74 )mm( thgie
59 29 )mm( htdiW
821 801 )mm( htpe
Weight including Paper Roll and Battery Pack (g) 345 446
Max Outer Diameter for Paper Roll (mm) 35 55
Typical Paper Roll Length (m) 13.5 34
Paper Roll Order Code A05836TPR1 A05856TPR1
Able Systems Limited
Denton Drive, Northwich, Cheshire, CW9 7TU England
T: +44 (0) 1606 48621 F: +44 (0) 1606 44903
www.able-systems.com
T H E P O W E R T O P R I N T
ally to iPod,
sible for the
operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or
Made for:
iPad (4th generation), iPad mini, iPad (3rd generation), iPad 2, iPhone 5, iPhone 4S,
iPhone 4, iPhone 3GS, iPod touch (4th generation)
iPad®, iPhone® and iPod touch® are trademarks of
Apple Inc. registered in the U.S. and other countries.
WARNING: Only use Able Systems approved Battery Packs and Chargers
For a Full User Guide please visit our Website: www.able-systems.com
To learn more about Able’s Print App, please visit www.able-systems.com/able-print-app.asp
Document Reference: V1.0
Download the
FREE app here!
/
