Swann STCL408WUK Service Information

Brand: Swann

Model: STCL408WUK

Category: Electric laundry dryers

Type: Service Information

This manual is also suitable for

Indesit Company UK Ltd

Service

Information

SWAN brand

Entry Level

ELECTRONIC

CONDENSER

TUMBLE DRYERS

Models Covered:

STCL407WUK 87207

STCL407BUK 87208

STCL408WUK 87209

STCL408BUK 87210

5407837 Issue 2 July 2015

SM003992 ~ C00307711

PLEASE NOTE:

These models do not

display Fault Codes if a

Fault occurs.

Refer to the Fault Finding

details on page 6.

2 of 34

Service Manual UK

Indesit

Company

English

SAFETY NOTES & GENERAL SERVICING ADVICE

1. This manual is NOT intended as a comprehensive repair/maintenance guide to the appliance.

2. It should ONLY be used by suitably qualified persons having technical competence applicable

product knowledge and suitable tools and test equipment.

3. Servicing of electrical appliances must be undertaken with the appliance disconnected (unplugged)

from the electrical supply.

4. Servicing must be preceded by Earth Continuity, Earth Resistance and Insulation Resistance

checks.

5. Personal safety precautions must be taken to protect against accidents caused by sharp edges on

metal and plastic parts.

6. After servicing the appliance must be rechecked for Electrical Safety. In the case of appliances

which are connected to a water supply (i.e.: Washing Machines, Dishwashers & Food Centres etc.)

checks must be made for leaks from seals gaskets and pipe work and rectification carried out where

necessary.

7. It can be dangerous to attempt 'DIY' repairs / maintenance on complex equipment and the Company

recommends that any problem with the appliance is referred to its own Service Organisation.

8. Whilst the Company has endeavoured to ensure the accuracy of the data within this publication they

cannot hold themselves responsible for any inconvenience or loss occasioned by any error within.

SERIAL NUMBER / INDUSTRIAL CODE EXPLANATION

Serial Number Example

1 10 02 0895

Four remaining digits = Build number that day 895

built

Third two digits = Day of manufacture 2

of month

Second two digits = Month of manufacture October

First digit = Year of manufacture 2011

Industrial Code Example

37 24455 0010

Last four digits = 0000 original production.

Second five digits = COMMERCIAL CODE*

First two digits = Factory of origin

* Vital for correct model information and system identification

Other numbers denote major production changes

3 of 34

Indesit Company

Service Manual UK English

INDEX

Safety & Servicing Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Serial Number / Industrial Code Explanation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Production Changes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Model Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Energy Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Fault Finding / Test Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 10

Thermistor Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Heater Connection Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Dryer Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 - 16

Dryer Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 - 19

Dryer Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 - 23

Component Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 - 25

Programme Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Control Board Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 - 28

Dismantling - Condenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 - 33

Production Changes

February 2015 Settings File updated to fix Dryer not heating when used in locations with a low

ambient temperature (Garages / Outhouses etc.)

Thermistor Resistance value chart added to this document (Issue 3).

4 of 34

Service Manual UK

Indesit

Company

English

Example Energy Information - STCL408W / STCL408B

This household tumble drier is a Condenser

The weighted Annual Energy Consumption (AEc)* kWh 1) 627.8

This household tumble drier is a Automatic

Energy consumption full load; Edry - kWh 2) 5.33

Energy consumption partial load; Edry½ - kWh 2) 2.83

Power consumption: o-mode (Po) - Watts 0.42

Power consumption: left-on mode (Pl) - Watts 2.24

Prog. Time - weighted (Tt) full & partial load - minutes 3) 112

Full load (Tdry) - minutes 151

Partial load (Tdry½) - minutes 82

weighted (Ct) full & partial load 3) 71

full load (Cdry) 71

partial load (Cdry½) 71

Airborne acoustical noise emissions - dB(A) re 1 pW 68.0

Programme time in minute, for program “Synthetics” full load 85

Partial load for program “Synthetics” N/A

Average condensation eciency - %

1) "Standard cotton” at full and partial load is the standard programme to which the

information in the label and the che relates. The standard cotton program is

suitable to dry at cupboard level (0%) cotton laundry and is the most ecient

programme in terms of energy consumption. Partial load is half the rated load.

2) based on 160 drying cycles of the standard cotton programme at full and partial

load, and the consumption of the low-power modes. Actual energy consumption

will depend on how the appliance is used.

3) Weighted average of 3 cycles at full load and 4 cycles at half load.

egulation 932/2012.

Energy consumption in kWh, for program “Synthetics” full load 1.93

Energy eciency class on a scale from A+++ (low consumption)

to D (high consumption)

Duration of the 'left-on mode' for power management system -

minutes

Condensation eciency class on a scale from G (least ecient) to

A (most ecient)

roduc t Data - R egulation 392/2012.

Brand

Swan

Model

STCL 408W (UK) STCL 408B (UK)

Rated capacity of cotton laundry for the "standard cotton

programme" at full load - kg

8.0

5 of 34

Indesit Company

Service Manual UK English

SPECIFICATIONS

Introduction Date August 2014

Features Electronically controlled tumble dryer comprising an combined interface

and control module fitted to the rear of the dashboard.

Country of Origin UK

Dimensions

Height 850 mm

Width 595 mm

Depth 623 mm

Net Weight 36.87 kg

Colour White

Energy Class B or C Depending on model (2012 Energy Label Regulations)

Noise Level 69db

Power Consumption

Left On 2.24 watts

Off Mode 0.42 watts

Drum Volume 112 Litres

Electronics Stripped Arcadia

Heater High Heat 2.3 kW

Heater Controls Variable using Electronic Controls and sensors

Sensing Levels 3 or 5 depending on model.

Control Thermostats Cycling Thermostat 120

°C

One Shot Thermostat 143 °C

Motor Type 362/363-Single Phase Capacitor run 2 pole Induction Motor 2800 rpm

Capacitor 8.5uF

Approvals CE, IMQ

6 of 34

Service Manual UK

Indesit

Company

English

FAULT FINDING

FAULT CODES

These models DO NOT display Fault Codes when the dryer develops a fault.

However an Auto Test feature is available to help diagnose faults.

Preliminary Checks:

Before performing any tests ALWAYS check that the Water Container is empty and that the Condenser

Unit and the Drum Filter are NOT blocked with fluff or lint, as this may be the cause or partial cause of

the of the fault.

Auto Test

If a Fault is detected the dryer will not move on to the next phase of the test, but will perform the

following sequence:

> Beep Once

> Pause for 30 Seconds

> Beep 3 Times

> The End LED will display

This will Indicate the dryer has a Fault, but it will not indicate the exact cause of the problem.

Observing at which phase the auto test ends gives an indication of the type of fault and cause.

See the information on the following pages.

Water container

Condenser Unit

Condenser cover

Catches

Filter

Handle

Air intake

Ta p

Rear

Front

Condenser

unit

7 of 34

Indesit Company

Service Manual UK English

Auto Test Sequence

Before Starting the Auto Test, make sure the Water Container is empty, the Filter and

Condenser are Clear of fluff or lint.

Auto Test - Preparation:

If you are including the Conductivity Sensor Test when running the test procedure:

1. Attach the magnetic end of the 270 K ohm test lead to the metal strip conductivity sensor inside

the drum.

2. Connect the ring terminal end to an earth point on the cabinet of the machine. (The Air Duct fixing

screw is recommended).

3. After attaching, check Earth Continuity between this ring terminal and the mains power plug Earth

pin on or the metal rear panel of the dryer, using a multimeter.

The continuity resistance reading should be 1 ohm or less.

Magnet fixed to sensing strip inside the drum Ring terminal end fixed under air duct screw

Routing of wire and resistor. Safe position of 270K ohm resistor

assembly with door closed

270K

450 mm

180 mm

Magnet Screw fixing

8 of 34

Service Manual UK

Indesit

Company

English

AUTO TEST - CONDENSER DRYERS

SAFETY WARNING !

When performing the Auto Test you will need to remove the top cover of the Dryer while

Electrical power is still applied.

To avoid the risk of electric shock, during this sequence you MUST make certain no

persons have any contact with the LIVE area around the Mains Terminal Block (cable entry

position) or main Power module behind the Console.

Preparation:

1. Remove the 2 screws securing the top cover to allow its removal when required during the test

sequence.

2. If necessary fit the Magnetic Test resistor. See page 7 for details.

To Enter Auto Test Mode - Condenser Models

1. The dryer must be plugged into the electricity supply with the Programme Selector set to the

“OFF” Position.

2. Turn the Selector Clockwise to Programme 1. Wait for the LED’s to turn OFF.

3. Push the Delay Option Button once.

4. Turn the Selector Clockwise to Programme 2.

5. Push the Delay Option Button once.

6. Turn the Selector Anti-Clockwise to Position 15.

7. Push the Start Button once.

This starts the test, indicated by the drum rotating clockwise for a short period - approximately

7 -8 seconds.

Note: If after starting the Auto Test and the drum has not Paused within 15 seconds, the auto test

has not been entered successfully, turn the control Knob to OFF, and repeat the above sequence.

TEST SEQUENCE - for a CONDENSER DRYER which has no detectable Faults

1. The Drum Rotates Clockwise for about 7 or 8 seconds.

Pause.

At this point remove the top cover. Remove the Water Bottle and pour 300 ml of water into the

Water Bottle support. (This will operate the Float Switch at the base of the dryer).

2. Refit the Water Bottle (if the Water Bottle is not replaced the test will fail at this point).

3. The dryer will pause until the Float Switch has moved to the full position.

The drain pump will turn on and the drum will rotate Clockwise for about 15 seconds.

The water that was poured into the support (filling the pump) will be pumped into the water bottle.

Pause for 5 seconds.

4. The Drum Rotates Anti-Clockwise with the Heater On (both elements) until the Rear Thermistor

detects a temperature Rise, - the heater then turns OFF and the drum continues to rotate.

Pause for 5 seconds.

5. The Drum Rotates Clockwise with the Heater On until the Front Thermistor detects a temperature

change, the Heater turns Off and the drum continues to rotate.

Long Pause.

6. 3 Beeps then the END LED Illuminates.

7. Test Ends.

9 of 34

Indesit Company

Service Manual UK English

TEST SEQUENCE - for a CONDENSER DRYER which has a Fault,

1. The Drum rotates clockwise for about 7 to 8 seconds

Step Phase: Float switch operation and Drain Pump operation

At this point remove the top cover. Remove the Water Bottle and pour 300 ml of water into the

Water Bottle support. This will operate the Float Switch at the base of the dryer.

2. Refit the Water Bottle (if the Water Bottle is not replaced the test will fail at this point).

3. The dryer will pause until the Float Switch has moved to the full position.

The drain pump will turn on and the drum will rotate Clockwise for about 15 seconds - actual Time

depends on quantity of water in the base reservoir.

The water that was poured into the support (filling the pump) will be pumped into the water bottle.

Pause 5 seconds.

Step Phase: Heater Operation and Rear Thermistor Temperature Check

4. Drum Rotates Anti-Clockwise with the Heater On (both elements) until the Rear Thermistor

detects a temperature Rise, - the heater then turns OFF and the drum continues to rotate for a

short period.

Pause for 5 seconds.

Step Phase: Heater Operation and Front Thermistor Temperature Check

5. Drum turns Clockwise with Heater On (both elements), until the Front Thermistor detects a

temperature change.

6. Heater will Turn Off, the Drum will continue for a few minutes..

Step Phase: Conductivity Sensor Check (only applies if magnetic resistance is being used)

8. Test Ends

If the pump is faulty or a there is a blockage in the hose or a pump wiring fault, the

Water container will not fill with water at this point, and the drum will continue to turn

for approx. 3 minutes, then the dryer beeps, pauses for 30 seconds, beeps 3 times

then the Test Ends.

If the Rear Thermistor, Thermostat or Heater is Open Circuit (both Elements) or

disconnected the Test Cycle will finish at this point - then the dryer beeps, pauses

for 30 seconds, beeps 3 times then the Test Ends.

If the Front Thermistor, is Open Circuit or disconnected the Test Cycle will finish at

this point - then the dryer beeps, pauses for 30 seconds, beeps 3 times then the

Test Ends.

With Magnetic test resistor fitted

and Sensor Circuit OK

Without Magnetic test resistor fitted

OR fitted but Sensor Circuit not OK

Long Pause,

3 Beeps,

End LED is Illuminated.

Pause,

Beep,

Long Pause,

3 Beeps,

End LED is Illuminated.

10 of 34

Service Manual UK

Indesit

Company

English

DRYER OPERATION CHECK - Condenser Models

When Checking Heater, Drum Action or Thermistor Operation, you are advised to use a Timed

Programme.

When Sensor Programmes are used, after the module has estimated the weight of the clothes and the

cycle time required to dry the clothes, the Dryer will start to reverse tumble.

Note: This weight and estimated drying time are calculated by the module which monitors the front

thermistor temperature increase in the Front Air Duct over a period of time.

For example, a small load will allow a faster temperature rise at the front thermistor.

A large load would cause the temperature to rise more slowly.

Drum

When set to a Timed Programme the machine will reverse for a short period approximately every 5

minutes.

Heater

Faulty or Disconnected Thermistors (Front and Rear) and the associated wiring will cause the

machine not to heat. (If an Auto Cycle is used the dryer may operate at ½ Heat, depending on cycle

used).

In these instances the machines will complete the Cycle without Heating with no indication to the user,

other than the load will be cold and wet at the end of the cycle.

One Element Open Circuit - Dryer works at 1.15 kW and dries normally taking slightly longer to

complete the cycle.

Thermistors

Rear Thermistor (Located on Heater Frame) next to the Cycling and One-Shot cut-outs.

11 of 34

Indesit Company

Service Manual UK English

Thermistor Tables

When testing these Thermistors make sure you have selected the CORRECT resistance range on

your test meter for the value you expect to see. The resistance value varies with temperature.

FRONT THERMISTOR REAR THERMISTOR

Temperature

°C

Resistance

KΩ

Temperature

°C

Resistance

KΩ

-20 462.89 -20 958.78

-10 268.29 -10 549.14

0 160.39 0 324.98

10 98.66 10 198.37

20 62.32 20 124.37

25 50.00 25 100.00

30 40.35 30 80.544

40 26.73 40 53.173

50 18.096 50 35.878

60 12.496 60 24.768

70 8.792 70 17.418

80 6.296 80 12.442

85 5.361 85 10.582

90 4.583 90 9.0436

100 3.388 100 6.6843

110 5.0111

Example: Front Thermistor

If the ambient temperature where

you are testing is 15°C you would expect to get a

reading of approximately 80.40KΩ.

(If the thermistor has warmed up because of

handling or operation of the dryer then the meter

reading will be a lower value)

The Rear Thermistor is a different component with

a different specification - refer to the chart

120 3.8064

125 3.3330

130 2.9262

140 2.2754

150 1.7891

12 of 34

Service Manual UK

Indesit

Company

English

Heater Connection Details

Cable Colours

Heater / Thermistor Connector Plug

Always fit a cable

tie to secure the

Heater connectors

together.

dynamic/upper heater

brown

orange

white

link

hot/rear NTC

red

static/lower heater

one shot

cycling

cut-out

thermostat

cycling one shotthermistor

Indesit Company

13 of 34

Service Manual UK English

WIRING DIAGRAM - Entry Level CONDENSER Models

blue

red

black

cycling

thermostat

one shot

cut-out

door switch

brown

orange

front NTC

hot/rear NTC

float switch

drain pump

PSC Motor

with protector

blue

red

black

Capacitor

main connection

with suppressor

brown

blue

red

white

red

blue

white

Drum assy

sensing

strip

orange

blue

red

CONNECTOR

ON BOARD WAYS WIRES DESCRIPTION

CN1 5 5 I 2C

CN2 4 4 UART BPM motor

CN3 1 1 earth

CN4 1 1 sensing

stri p

CN5 6 4 drain pump

- Ňoat switch

CN6 3 2 hot/re ar NTC

CN7 3 2 front NTC

CN9 3 3 PSC motor

CN10 3 3 heater

CN11 4 4 suppressor - door swi tch

HARNESS INDESIT CODE DESCRIPTION

H1 21023259100 motor

drain pump

Ňoat

switch

front NTC

hot

NTC

H2 16002965300 Sensing strip

H3 16002965200 Earth

H4 16002974000 Heater

H5 16002973900 s

uppressor -

door switch

green/yellow

static/lower heater

dynamic/upper heater

Heater cover assy

ccw

4,8

160029741

160029743

160029744

160029742

black

160029653

160029652

160029739

160029738.00

CN1CN2

CN3

CN4

CN5CN9 CN6

CN7

CN10

CN11

CONDENSER DRYER

14 of 34

Service Manual UK

Indesit

Company

English

INSTALLATION

The dryer MUST be located away from gas stoves,

hobs or heaters.

If the dryer is located under a work surface, there

must be a 10 mm gap around any top or above the

dryer and a minimum 15 mm space along each side.

This is to ensure correct air circulation.

CONDENSER DRYERS

Draining the dryer into an Internal Drain

If the dryer drains into an external drain, the water container will not need to be regularly emptied.

The height of the drain must be less than 1 metre from the bottom of the dryer.

Remove the existing hose from the position shown, Fig. 1. Fit a suitable length of hose (Part No.

C00279043) to the location shown in the photo (Fig. 2).

Confirm the hose is not squashed or kinked when the dryer is in its installed position.

15 mm

10mm

Remove this hose

Fig.1

Outlet Spigot

Fig.2

New drain hose fitted

Fig.3

15 of 34

Indesit Company

Service Manual UK English

LOOKING AFTER THE DRYER

FLUFF FILTER

The fluff filter MUST be cleaned after every use.

Never use a Tumble Dryer without

the filter in place.

1. Remove the filter from the

dryer.

2. Open and clean the filter.

WATER CONTAINER

Empty the water container after every cycle.

1. Remove the water container from the dryer.

2. Empty the water container intoa sink.

3. Replace the water container ensuring it is fully pushed home.

NOTE: -

Priming for water collection.

When the dryer is new, depending on the type of load dried. It may take one or two cycles for water to

be collected in the water container.

Once primed, water will be collected after every drying cycle.

16 of 34

Service Manual UK

Indesit

Company

English

CONDENSER UNIT - CONDENSER DRYERS

For normal domestic use, the condenser should be cleaned once a month.

1. Open the condenser cover by pulling on the handle.

2. Rotate the 3 clips and pull the condenser towards you to remove. Some water is normal.

3. Flush the condenser unit from the rear to remove fluff deposits.

4. Refit the condenser, with the arrows pointing upwards. Once pushed home, rotate the 3 clips to

lock into place.

Open this flap by pulling the handle

Release the latches to remove the condenser

Remove and Rinse the Condenser

Refit the condenser the correct way up

over a sink or bath

17 of 34

Indesit Company

Service Manual UK English

DRYER OVERVIEW

Introduction of Simplified Electronics

These Models are fitted with a new Electronic Module, which is fixed to a plastic carrier, located behind

the Console.

This Module replaces the Control Module (previously located in the Base), the Display Module +

Control Interface (previously located behind the Dashboard) and the Module to Display interface

harness, fitted to 2013 Production Tumble Dryers.

It is NOT interchangeable with earlier products which use 2 modules.

The module is covered with a white plastic water shield which must always be fitted correctly and

retained with its fixing clip.

Programming Connector

The module is programmed using Memwriter and a Hardware

Key or with a SmartCard Reader and Card, connected using a

Low End Adaptor.

(See pages 27 & 28 - Contol Board Programming)

These models have an Auto Test Cycle. See pages 7 & 8.

Fault Codes

These Models do NOT display a fault code if the dryer is in a

Fault Condition. See page 6.

Plastic Wate

Shield

Control

Module

Low End

Adaptor

Connection

point

Drum

Fluff

Barrier

(if fitted)

Low End Adaptor connector

18 of 34

Service Manual UK

Indesit

Company

English

DRYER OVERVIEW - CONDENSER MODELS

These Condenser Auto Tumble Dryers are freestanding with a round door on the front that can be

opened to allow the drum to be loaded with clothes.

The door is NOT reversible.

The facia moulding across the top of the front panel houses the dryer user controls and water

container.

Within the cabinet is a drum, which is capable of accepting a maximum 7 or 8 Kg* (depending on

model) load of damp clothing.

The drum is supported at the front by 4 plastic bearing pads or 1 drum support wheel and 2 bearing

pads (depending on model) mounted on the front air duct and a single bearing at the rear located in

the rear panel. A shaft fixed to the rear of the drum runs in the rear bearing.

The drum is driven by a belt, which passes around its periphery and onto the shaft of a motor secured

to the base of the dryer. The belt is elasticated and tensioned by a pulley mounted to the motor.

As well as driving the drum the motor also drives impellers (rotors), fixed to each end of its shaft.

The front impeller draws cold air into the dryer, while the rear impeller recirculates drying air. The

addition of heat to the recirculating air is provided by a heating unit attached to the rear panel, enabling

the air to hold moisture when in contact with the wet load, thus causing it to dry.

As the warm recirculating air passes through the drum it collects lint as well as moisture. To prevent

the lint from blocking the heat exchanger (condenser), the air is passed through a filter located in the

front air duct door. The filter unit is positioned so as to be easily removable for cleaning by the user.

After passing through the filter, the circulating air is dusted through passageways in a heat exchanger

(condenser) located in a housing on the base of the dryer. Cold air is drawn into the dryer and flows

across the heat exchanger passageways. This cold air is not mixed with the warm damp recirculating

air, but is drawn into the dryer. This has the effect of reducing the circulating air temperature, causing it

to give up its moisture. (Cold air holds less moisture than hot air.) The now warm cooling air is

exhausted through the rear of the dryer.

The moisture removed from the recirculating air is pumped to a removable container mounted in the

left-hand side of the console. The user can easily withdraw the container to dispose of the collected

condense.

There is no requirement for venting to atmosphere on this dryer.

Cooling Air Circuit (open to atmosphere)

Recirculating Air Circuit (sealed)

CONDENSER DRYER

AIR FLOW

19 of 34

Indesit Company

Service Manual UK English

Controls Overview

The user controls consist of a programme selection knob, option buttons and a Start/Pause button.

The control system consists of a user interface and control module, a thermistor mounted at the top of

the front air duct and one mounted on the heater assembly and a conductivity sensor.

The conductivity sensor is mounted in the front air

duct.

A single wire connects the sensor to the control

module.

The thermistors and conductivity sensor send values

back to the control module. The control module then

determines the programme duration and required

dryness of the load in a set of values for a particular

programme held within the control module software.

The combined Control and Power Module is a single

unit located at the top front right hand side of the dryer directly behind the console panel.

This module does not have a standard service port, and requires the use of a Low End Adaptor to

connect the Hardware Key to permit module programming.

The control module must be programmed with the relevant eeprom file if the control module is

replaced, the eeprom file becomes corrupted or if an updated file becomes available.

Programme Duration:

Once the programme has started the module will determine programme length for the size and type of

load. This detection is made within 10 minutes of the start of the programme and is achieved by use of

the front thermistor, rear thermistor and conductivity sensor. The module will then adjust the

programme time accordingly.

If the clothes are not sensed as dry when the 10 minute Cool Tumble period is reached, the module

does not start the Cool Tumble but continues to dry the clothes until the value from the conductivity

sensor indicates that the clothes are dry. The programme then advances into Cool Tumble.

Maximum Programme Period:

If after the maximum permitted programme time of 300 minutes (Note: this is an internal default value.)

the clothes are still not sensed as dry, the programme advances to Cool Tumble and completes the

programme. No fault is indicated if this occurs.

Heater Control

The control module also controls the heater. This has an upper and lower element. The lower (static)

element is permanently energised (except in cool tumble) and the upper element (dynamic) is cycled

on and off by the control module during a programme to maintain the correct temperature within the

drum for the programme selected.

If the user turns off the power or disconnects the mains cable or there is a power cut, the dryer will

remember its last settings and resume the programme when the start button is pressed.

If the event of a controls or thermistor failure, a cycling thermostat and one-shot thermostat are fitted

as safety devices.

Bearing Pads

Conductivity

Sensing Strip

Drum Support Wheels

20 of 34

Service Manual UK

Indesit

Company

English

FUNCTIONS DESCRIPTION

The Drying Guide allows you to consult a user friendly table of fabric types and load capacities.

The PROGRAMME knob sets the programme: rotate it until the indicator is pointing to the programme

you want to select. This will also power the dryer to the ON state. This replaces the On/Off button

found on previous models.

When either ’OFF’ (Hotpoint models) or the knob marker ’()’ (Indesit models), is positioned in the 12

o'clock position, it turns the machine Off and Cancels the Programme.

The OPTION buttons/lights select available options for your selected programme. The lights indicate

that the option has been selected.

The START/PAUSE button/light starts a selected programme. When you press this button there

will be one beep and the progress lights will flash to confirm the action. When a programme is running,

holding this button in pauses the programme and stops the dryer.

The light is green when programme is running, flashing amber if the programme has been paused or

flashing green if on stand-by waiting to start a programme.

Stand-by Mode

30 minutes after a programme has finished, if the dryer is still 'On' and no buttons have been touched,

the dryer will go into Stand-By mode. The LEDs and display will switch off. To reactivate and to remove

the dryer from Stand-By mode, turn the Programme Selector to position "1".

It will take a few seconds to recover from "Standby".

Another programme can be started or the dryer switched off by turning the selector to the OFF position.

The Progress or Delay lights show you the status of the programme, or the delay time when they

flash. During a delayed start the lights flash to show the delay selected. When (not flashing) they show

each stage of the programme by the corresponding light turning on.

The Empty Water indicator light signals that the water container should be emptied. The light will take

a few seconds to go out after replacing the empty water container, the dryer must be running for this to

happen. Note: If the water bottle fills the indicator light flashes, the heat is turned off and your clothes

will not dry.

The Clean Filter light gives you a reminder before every programme that it is essential to clean the

filter every time the dryer is used.

The Clean Condenser light gives you a reminder that it is essential to clean the condenser at regular

intervals.

Page is loading ...

Swann STCL408WUK Service Information

Brand: Swann

Model: STCL408WUK

Category: Electric laundry dryers

Type: Service Information

This manual is also suitable for

Download PDF

report

Swann STCL408WUK Service Information

This manual is also suitable for

Swann STCL408WUK Service Information

Related papers

Other documents