BLACK DECKER ka 270 gtk Owner's manual

Page is loading ...

6

ENGLISH

Intended use

Your Black & Decker sander has been designed for sanding

wood, metal, plastics and painted surfaces. This tool is

intended for consumer use only.

General safety rules

Warning! Read all instructions. Failure to follow all instructions

listed below may result in electric shock, fire and/or serious

injury. The term “power tool” in all of the warnings listed

below refers to your mains operated (corded) power tool or

battery operated (cordless) power tool.

SAVE THESE INSTRUCTIONS.

1. Work area

a. Keep work area clean and well lit. Cluttered and dark

areas invite accidents.

b. Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

c. Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodified

plugs and matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase the

risk of electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the influence

of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in

serious personal injury.

b. Use safety equipment. Always wear eye protection.

Safety equipment such as dust mask, non-skid safety

shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c. Avoid accidental starting. Ensure the switch is in

the off position before plugging in. Carrying power

tools with your finger on the switch or plugging in power

tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of these

devices can reduce dust related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source before

making any adjustments, changing accessories, or

storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

7

ENGLISH

g. Use the power tool, accessories and tool bits etc.,

in accordance with these instructions and in the

manner intended for the particular type of power

tool, taking into account the working conditions

and the work to be performed. Use of the power tool

for operations different from those intended could result

in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Additional safety instructions for sanders

◆ Always wear a dust mask whenever sanding.

◆ Thoroughly remove all dust after sanding.

◆ Take special care when sanding paint which is possibly

lead based or when sanding some woods and metal

which may produce toxic dust:

- Wear a dust mask specifically designed for protection

against lead paint dust and fumes and ensure that persons

within or entering the work area are also protected.

- Do not let children or pregnant women enter the work

area.

- Do not eat, drink or smoke in the work area.

- Dispose of dust particles and any other debris safely.

◆ Before using the tool on wooden workpieces, make sure

to fit the dust cassette.

◆ Before using the tool on metal workpieces, make sure to

remove the dust cassette.

◆ Never use the tool without a sanding sheet.

◆ Never use the tool without a sanding base.

◆ This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised

to ensure they do not play with the appliance.

◆ If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

Features

This tool includes some or all of the following features.

1. On/off switch

2. Gel comfort grip (KA270GT(K) only)

3. Dust cassette

4. Large detail sanding base

5. Tip holder

6. Sanding base tip

Fig. A

7. Random orbit sanding base

8. Profile attachment (KA270(GT)K only)

9. Sanding profiles (KA270(GT)K only)

10. Detail finger attachment (KA270(GT)K only)

11. Spare sanding base tip (KA270(GT)K only)

12. Louvre attachment (KA270LDK only)

Assembly

Warning! Before assembly, make sure that the tool is switched

off and unplugged.

Random orbit sanding base

With this sanding base, you can use the tool as a random orbit

sander.

Fitting and removing the sanding base (fig. B)

◆ Place the sanding base (7) onto the spindle (13).

◆ Place the washer (14) onto the spindle.

◆ Insert the Allen screw (15) into the screw hole in the spindle.

◆ Tighten the Allen screw using the Allen key (16) supplied.

◆ To remove the sanding base, remove the Allen screw (15)

and washer (14).

Fitting sanding sheets (fig. C)

◆ Hold the tool with the sanding base (7) facing upwards.

◆ Place the sanding sheet (17) onto the sanding base (7).

The holes in the sheet do not need to line up with the

holes in the base.

Large detail sanding base

With this sanding base, you can use the tool as a detail

sander or an orbital sander.

Fitting and removing the sanding base (fig. D & E)

For detail sanding, the pointed end should face forward as in

fig. D. For sanding large areas, the pointed end should face to

the back as in fig. E.

◆ Place the sanding base (4) onto the spindle (13). Make

sure that the legs of the base locate into the tool.

◆ Place the washer (14) onto the spindle.

◆ Insert the Allen screw (15) into the screw hole in the spindle.

◆ Tighten the Allen screw using the Allen key (16) supplied.

◆ To remove the sanding base, remove the Allen screw (15)

and washer (14).

8

ENGLISH

Fitting sanding sheets (fig. F)

◆ Detach the two diamond-shaped tips (18) from the

sanding sheet (19).

◆ Hold the tool with the sanding base facing upwards.

◆ Place the sanding sheet (19) onto the sanding base,

making sure that the holes in the sheet line up with the

holes in the base.

The diamond-shaped tip (18) can be reversed and replaced

when worn.

◆ When the front part of the tip is worn, detach it from the

sheet, reverse it and press it onto the sanding base again.

◆ When the whole tip is worn, remove it from the sanding

base and fit a new tip.

Tip of the sanding base (fig. G)

When the sanding base tip (6) is worn, it can be reversed or

replaced. When the tip holder (5) is worn, it can be replaced.

Spare parts are available from your Black & Decker dealer.

◆ Remove the screw (20).

◆ Reverse or replace the worn part.

◆ Fit and tighten the screw.

Finger attachment (fig. H)

The finger attachment is used for fine detail sanding.

◆ Remove the screw (20).

◆ Remove the diamond-shaped tip holder (5) from the

sanding base.

◆ Fit the finger attachment (10) onto the sanding base.

◆ Fit and tighten the screw.

◆ Fit the appropiate sanding sheet (21) onto the finger

attachment.

Profile attachment

The profile attachment is used for contour sanding.

Fitting the profile attachment (fig. I)

◆ Remove the screw (20).

◆ Remove the diamond-shaped tip holder (5) from the

sanding base.

◆ Fit the profile attachment (8) onto the sanding base.

◆ Fit and tighten the screw.

Fitting and removing a sanding profile (fig. J1 & J2)

◆ Choose the sanding profile most suitable for your application.

◆ Place one end of the sanding profile (9) into the recess at

the front end of the profile attachment (8).

◆ Push the other end of the sanding profile until it clicks

into place.

◆ To remove the sanding profile (9), push it forward and pull

the rear end out of the profile attachment (8).

Fitting a sanding sheet onto a sanding profile (fig. K)

◆ Align the sanding sheet (22) with the sanding profile (9).

◆ Press the sanding sheet onto the sanding profile, making

sure that the sanding sheet follows the shape of the profile.

Louvre attachment (fig. L & M)

With the louvre attachment you can work in crevices.

◆ Remove the screw (20).

◆ Remove the diamond-shaped tip holder (5) from the

sanding base.

◆ Fit the louvre attachment (12) onto the sanding base.

◆ Fit and tighten the screw.

◆ Fit the appropiate sanding sheet (23) onto the louvre

attachment.

The additional piece of velcro fastener (24) can be attached to

the top surface of the louvre attachment (12) to allow for

sanding using both sides.

◆ Remove the backing paper from the velcro fastener (24).

◆ Stick the velcro fastener to the top surface of the louvre

attachment.

◆ Fit the sanding piece (23) to the velcro fastener.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Do not cover the ventilation slots when using the

tool. Hold the tool as shown in fig. Q. Make sure that the

sanding base is flat on the workpiece.

Switching on and off (fig. N)

◆ To switch the tool on, set the on/off switch (1) to position I.

◆ To switch the tool off, set the on/off switch to position O.

Automatic brake system (ABS)

This tool has an automatic brake system. When the tool is not

on the work surface, this feature keeps the speed of the disc

below the speed of the motor. When the tool is switched off,

the disc will stop very quickly.

Emptying the dust cassette (fig. O & P)

The dust cassette should be emptied every 10 minutes of use.

◆ Pull the dust cassette (3) to the rear and off the tool.

◆ Remove the cover (25) by twisting it counterclockwise.

◆ Hold dust cassette with the filter (26) facing down and

shake the cassette to empty the contents. Shake the

cover to empty the contents.

◆ Refit the cover (25) onto the dust cassette, twisting it

clockwise until it locks into place.

◆ Refit the dust cassette onto the tool.

9

ENGLISH

Cleaning the dust cassette filter

The dust cassette filter is re-usable and should be cleaned

regularly.

◆ Empty the dust cassette (3) as described above.

◆ Pull the filter (26) off the dust cassette.

◆ Shake off excess dust by tapping the filter into a dustbin.

Warning! Do not brush or use compressed air or sharp

objects to clean the filter. Do not wash the filter.

◆ Replace the filter.

◆ Refit the cover.

◆ Refit the dust cassette onto the tool.

Hints for optimum use

◆ For user comfort, the tool can be operated with one or

two hands (fig. Q). Do not place your hands over the

ventilation slots.

◆ Do not exert too much pressure on the tool.

◆ Regularly check the condition of the sanding sheet.

Replace when necessary.

◆ Always sand with the grain of the wood.

◆ When sanding new layers of paint before applying

another layer, use extra fine grit.

◆ On very uneven surfaces, or when removing layers of

paint, start with a coarse grit. On other surfaces, start

with a medium grit. In both cases, gradually change to

a fine grit for a smooth finish.

◆ Consult your retailer for more information on available

accessories.

Maintenance

Your tool has been designed to operate over a long period of

time with a minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and regular cleaning.

◆ Clear the cooling vents and slots with a clean, dry paint

brush.

◆ Clean the housing with a clean, damp cloth. Do not use

solvents.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you find one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product

available for separate collection.

Separate collection of used products and packaging

allows materials to be recycled and used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the demand for

raw materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and

recycling of Black & Decker products once they have reached

the end of their working life. To take advantage of this service

please return your product to any authorised repair agent who

will collect them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local Black & Decker office at the

address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of our

after-sales service and contacts are available on the Internet

at: www.2helpU.com

Technical data

KA270

Voltage V

AC

230

Power input W 170

Oscillations (no load) min

-1

11,000

Orbits (no load) min

-1

22,000

Weight kg 1.53

EC declaration of conformity

KA270

Black & Decker declares that these products conform to:

98/37/EC, 89/336/EEC, EN 60745, EN 55014, EN 61000

L

pA

(sound pressure) 78 dB(A), L

WA

(acoustic power) 89 dB(A),

hand/arm weighted vibration 8.8 m/s

2

K

pA

(sound pressure uncertainty) 3 dB(A),

K

WA

(acoustic power uncertainty) 3 dB(A)

Kevin Hewitt

Director of Consumer Engineering

Spennymoor, County Durham DL16 6JG,

United Kingdom

1-5-2005

10

ENGLISH

Guarantee

Black & Decker is confident of the quality of its products and

offers an outstanding guarantee. This guarantee statement is

in addition to and in no way prejudices your statutory rights.

The guarantee is valid within the territories of the Member

States of the European Union and the European Free Trade

Area.

If a Black & Decker product becomes defective due to faulty

materials, workmanship or lack of conformity, within 24 months

from the date of purchase, Black & Decker guarantees to

replace defective parts, repair products subjected to fair wear

and tear or replace such products to ensure minimum

inconvenience to the customer unless:

◆ The product has been used for trade, professional or hire

purposes;

◆ The product has been subjected to misuse or neglect;

◆ The product has sustained damage through foreign

objects, substances or accidents;

◆ Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service staff.

To claim on the guarantee, you will need to submit proof of

purchase to the seller or an authorised repair agent. You can

check the location of your nearest authorised repair agent by

contacting your local Black & Decker office at the address

indicated in this manual. Alternatively, a list of authorised

Black & Decker repair agents and full details of our after-sales

service and contacts are available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.co.uk to

register your new Black & Decker product and to be kept up to

date on new products and special offers. Further information

on the Black & Decker brand and our range of products is

available at www.blackanddecker.co.uk

Page is loading ...

68

TYP

1

KA270

WWW.2helpU.com 08-06-05E14366

KA270LDK

KA270GTK

37

38

43

40

41

42

39

17

16

12

8

53

54

52

2

18

1

55

10

11

51

34

16

18

6

15

19

47

48

20

21

23

13

26

25

28

49

50

7

5

36

9

821

57

30

27

33

45

46

35

56

Page is loading ...

71

koneesi?

◆

E›Ó·È ÙÔ ÂÚÁ·ÏÂ›Ô ·˘Ùﬁ Ë

ÚÒÙË Û·˜ ·ÁÔÚ¿?

◆

Yes

◆

Ja

◆

Oui

◆

Si

◆

Ja

◆

Sí

◆

Sim

◆

Ja

◆

Ja

◆

Ja

◆

Kyllä

◆

¡·È

◆

No

◆

Nein

◆

Non

◆

No

◆

Nee

◆

No

◆

Não

◆

Nej

◆

Nei

◆

Nej

◆

Ei

◆

√¯È

◆

Dealer address

◆

Händleradresse

◆

Cachet du revendeur

◆

Indirizzo del

rivenditore

◆

Adres van de dealer

◆

Dirección del detallista

◆

Morada do

revendedor

◆

Återförsäljarens adress

◆

Forhandlerens adresse

◆

Forhandler adresse

◆

Jälleenmyyjän osoite

◆

¢ÈÂ‡ı˘ÓÛË ·ÓÙÈÚÔÛÒÔ˘

..........................................................................

Cat. no.:

✍

◆

Is this tool a gift?

◆

Ist dieses Gerät ein

Geschenk?

◆

S’agit-il d’un cadeau?

◆

Si tratta

di un regalo?

◆

Kreeg u de machine als cadeau?

◆

¿Ha recibido usted esta herramienta como

regalo?

◆

Recebeu esta ferramenta como

presente?

◆

Är verktyget en gåva?

◆

Er verktøyet en gave?

◆

Er verktøjet en gave?

◆

Onko kone lahja?

◆

∆Ô ÂÚÁ·ÏÂ›Ô Â›Ó·È ‰ÒÚÔ?

◆

Yes

◆

Ja

◆

Oui

◆

Si

◆

Ja

◆

Sí

◆

Sim

◆

Ja

◆

Ja

◆

Ja

◆

Kyllä

◆

¡·È

◆

No

◆

Nein

◆

Non

◆

No

◆

Nee

◆

No

◆

Não

◆

Nej

◆

Nei

◆

Nej

◆

Ei

◆

√¯È

◆

Is this tool your first purchase?

◆

Ist dieses

Gerät ein Erstkauf?

◆

Est-ce un 1er achat?

◆

Questo prodotto è il suo primo acquisto?

◆

Is

deze machine uw eerste aankoop?

◆

¿Es esta

herramienta la primera de este tipo?

◆

Esta ferramenta é a sua primeira compra?

◆

Är detta ditt första B&D-verktyg?

◆

Er dette ditt

første B&D verktøy?

◆

Er dette dit første B&D

verktøj?

◆

Onko tämä ensimmäinen B&D-

Dealer address Date of purchase

Händleradresse Kaufdatum

Cachet du revendeur Date d’achat

Indirizzo del rivenditore Data d’acquisto

Adres van de dealer Aankoopdatum

Dirección del detallista Fecha de compra

Morada do revendedor Data de compra

Återförsäljarens adress Inköpsdatum

Forhandlerens adresse Innkjøpsdato

Forhandler adresse Indkøbsdato

Jälleenmyyjän osoite Ostopäivä

¢ÈÂ‡ı˘ÓÛË ·ÓÙÈÚÔÛÒÔ˘ ∏ÌÂÚÔÌËÓ›· ·ÁÔÚ¿˜

✁

◆

Name

◆

Name

◆

Nom

◆

Nome

◆

Naam

◆

Nombre

◆

Nome

◆

Namn

◆

Navn

◆

Navn

◆

Nimi

◆

√ÓÔÌ·:

..........................................................................

◆

Address

◆

Adresse

◆

Adresse

◆

Indirizzo

◆

Adres

◆

Dirección

◆

Morada

◆

Adress

◆

Adresse

◆

Adresse

◆

Osoite

◆

¢ÈÂ‡ı˘ÓÛË:

..........................................................................

◆

Town

◆

Ort

◆

Ville

◆

Cittá

◆

Plaats

◆

Ciudad

◆

Localidade

◆

Ort

◆

By

◆

By

◆

Paikkakunta

◆

¶ﬁÏË:

..........................................................................

◆

Postal code

◆

Postleitzahl

◆

Code postal

◆

Codice postale

◆

Postcode

◆

Código

◆

Código postal

◆

Postnr.

◆

Postnr.

◆

Postnr.

◆

Postinumero

◆

∫ˆ‰ÈÎﬁ˜

..........................................................................

◆

Data protection act: Tick the box if you prefer

not to receive further information.

◆

Bitte

ankreuzen, falls Sie keine weiteren

Informationen erhalten möchten.

◆

Si vous ne

souhaitez pas recevoir d’informations, cochez

cette case.

◆

Barrate la casella se non

desiderate ricevere informazioni.

◆

A.u.b. dit vakje aankruisen indien u geen

informatie wenst te ontvangen.

◆

Señale en la casilla sino quiere recibir

información.

◆

Por favor, assinale com uma cruz

se não desejar receber informação.

◆

Vänligen

kryssa för i rutan om Ni inte vill ha information.

◆

Vennligst kryss av dersom du ikke ønsker

informasjon.

◆

Venligst sæt kryds i ruden

såfremt De ikke måtte ønske at modtage

information.

◆

Merkitkää rasti ruutuun, mikäli ette halua

vastaanottaa informaatiota.

◆

¶·Ú·Î·ÏÂ›ÛÙÂ Ó· ÛËÌÂÈÒÛÂÙÂ Â¿Ó ‰ÂÓ ı¤ÏÂÙÂ

Ó· ¿ÚÂÙÂ ÏËÚÔÊÔÚ›Â˜.

72

◆

GUARANTEE CARD

◆

GARANTIEKARTE

◆

CARTE DE GARANTIE

◆

TAGLIANDO DI GARANZIA

◆

GARANTIEKAART

◆

TARJETA DE GARANTÍA

◆

CARTÃO DE GARANTIA

◆

GARANTIBEVIS

◆

GARANTI KORT

◆

GARANTI KORT

◆

TAKUUKORTTI

◆

∫∞ƒ∆∞ E°°À∏™∏™

Português Por favor, recorte esta parte, coloque-a num envelope selado e

endereçado e envie-o logo após a compra do seu produto para o

endereço da Black & Decker do seu país.

Svenska Var vänlig klipp ur denna del och sänd den i ett frankerat kuvert till

Black & Deckers adress i Ditt land.

Norsk Vennligst klipp ut denne delen umiddelbart etter du har pakket ut

ditt produkt og legg det i en adressert konvolutt til Black & Decker

(Norge) A/S.

Dansk Venligst klip denne del ud og send frankeret til Black & Decker

i dit land.

Suomi Leikkaa irti tämä osa, laita se kuoreen ja postita kuori paikalliseen

Black & Decker osoitteeseen.

EÏÏËÓÈÎ· ¶·Ú·Î·ÏÒ Îﬁ„ÂÙÂ ·˘Ùﬁ ÙÔ ÎÔÌÌ¿ÙÈ Î·È Ù·¯˘‰ÚÔÌ‹Û·ÙÂ ÙÔ ·Ì¤Ûˆ˜

ÌÂÙ¿ ÙËÓ ·ÁÔÚ¿ ÙÔ˘ ÚÔ˚ﬁÓÙÔ˜ Û·˜ ÛÙËÓ ‰ÈÂ‡ı˘ÓÛË ÙË˜

Black & Decker ÛÙËÓ EÏÏ¿‰·

.

English Please complete this section immediately after the purchase of your

tool and send it to Black & Decker in your country. If you live in

Australia or New Zealand, please register by using the alternative

guarantee card supplied.

Deutsch Bitte schneiden Sie diesen Abschnitt ab, stecken ihn in einen

frankierten Umschlag und schicken ihn an die Black & Decker

Adresse Ihres Landes.

Français Découpez cette partie et envoyez-la sous enveloppe timbrée à

l’adresse de Black & Decker dans votre pays, ceci immédiatement

après votre achat.

Italiano Per favore ritagliate questa parte, inseritela in una busta con

francobollo e speditela subito dopo l’acquisto del prodotto

all’indirizzo della Black & Decker nella vostra nazione.

Nederlands Knip dit gedeelte uit en zend het direct na aankoop in een

gefrankeerde, geadresseerde envelop naar het adres van

Black & Decker in uw land.

Español Después de haber comprado su herramienta envíe usted, por favor,

esta tarjeta a la central de Black & Decker en su país.

✁

479726-00

06/05

BLACK DECKER ka 270 gtk Owner's manual

BLACK DECKER ka 270 gtk Owner's manual

in other languages

Related papers

Other documents