D-SDI IR Bullet CAMERA
XHC1080VB
About
this
manual
O.S.D (On Screen Display) Menu
140(H), 120(W), 254(D)
DC 12V
Max 6 [W]
IR OFF (280mA), IR ON(500mA)
ON/OFF
30/25P(1080P), 60/50P(720P)
2.1M Pixels, HD-SDI Bullet Camera
1/3" 2M Pixels Progressive Sensor
0.1 Lux @F1.2 Without DSS
0.00001Lux @F1.2 (LED ON)
Min illumination
DEFOG
INITIALIZATION
RS485
INFORMATION F/W VERSION
[1080p/30, 1080p/25, 720p/60, 720p/50]
[PROTOCOL, BAUDRATE(2400,4800,9600,14400,19200,115200),
ID(0~127)]
ENTER
HIGH LIGHT MASKING [OFF, ON]
[OFF, ON(0~10)]
[OFF, ON(SENSITIVITY (0~10), OBJECT DISPLAY (OFF, ON),
[DEEPLY, CLEARLY]
[AUTO, AUTO_EXT, MANUAL(TEMPERATURE, RED GAIN, BLUE
GAIN), PUSH]
[TITLE SET, TITLE DISPLAY, TITLE COLOR]
Supports 32 Quantity masking area
[OFF, ON]
TDN DELAY TIME at the AUTO mode
[AUTO, NIGHT]
Digital Slow Shutter limitation
Set the Exposure value [FULL, TOP, MIDDLE, BOTTOM]
[AUTO,COLOR-DAY,B/W-NIGHT,EXT_IN,EXT_OUT]
[0~20]
Exposure type [AUTO, MANUAL]
EXPOSURE
BRIGHTNESS [0~20]
EXP-AREA
Auto Gain Control , [0~20]
Select to DC-IRIS Lens [IN_NORMAL, IN_DEBLUR, OUTDOOR1,
DC-IRIS
Lens TYPE
Select to Manual-IRIS Lens
INSTRUCTION MANUAL
EXIT MENU
CAM TITLE
WHITE BALANCE
DAY & NIGHT
IMAGE QUALITY
IMAGE TONE
3D DNR MODE
COLOR
TITLE&MASKING
ADVANCED FUNC
SYSTEM
TDN MARGIN
ACE
Before installing and using the camera, please read this manual carefully.
Be sure
to
keep
it
handy
for
later
reference.
TROUBLESHOOTING
Before sending the camera out for repair, check the items
below. If the problem persists after checking these items,
contact your service center.
If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt of fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?
Do not open the cabinet exet during maintenance and
installation, as it may be dangerous and cause damages.
Do not put objects inside the unit
Make sure that no metal objects or flammable substances
get insdie the camera. It could cause fire, short-circuits or
damages.
Be careful when handling the unit
To prevent damage, do not drop the camera or subject
it to strong shock or vibration.
Install away from electric or magnetic fields.
Protect from humidity and dust.
Protech from high temperature
Be careful when installing colose to the ceiling , in a kitchen
or boiler room, as the temperature may raise to high levels.
Cleaning
Dirt can be removed from the cabinet only by wiping it
with a soft cloth moistened with a soft detergent solution.
Mounting Surface
The mounting surface material must be strong enough to
secure the camera.
PRECAUTIONS
SPECIFICATION
Feature
Please open the DOME bubble case.
Opening notc h located rear side of dome camera base case.
To adjust the focus, Spin the focus adjust lever on the Lens.
To adjust the zoom, spin the zoom adjust lever on the Lens.
Please tighten the focus & zoom wheel screw after the adjustment
in
CAMERA LENS SETTINGS
1/3” Panasonic Progressive CMOS Image Sensor
2.1M Pixels Full-HD Video resolu
on
Supported true day & night func
on (only D/T model)
Supported DC-IRIS func
on (only D/T model)
Supported 8 areas privacy masking
Supported ca
tle display
Supported BLC
Supported DSS
Supported WDR
Supported High Light Masking
Supported DNR & 3D DNR
Excellent Video Quality of 1080p 30fps/25fps & 720P 60fps/50fps
Supported Analog Composite Video Out simultaneously for easy service & easy camera installa
on
IP
66 Compatible
4. Please close the dome bubble cover.
O.S.D
1.
1.
1.
1.
1.
1.