M7 QE-131 User manual

Type
User manual
1
1.The maximum recommended air pressure during operation must not exceed 90 psi
(6.3bar). Higher air pressure may create unsafe operating conditions for the tool and
the user.
2.The compressed air should be cooled and have a water lter installed at the outlet
end of the compressor. Even with a water filter installed, some water may still
condense in the piping or hose and will enter the tool mechanism causing premature
damage to the tool. Therefore, it is recommended to install an air filter-lubricator
device somewhere between the tool and the compressor.
3.Always use an air compressor of the proper capacity to operate each tool.
4.Clean the hose with a blast of compressed air before connecting the hose to the air
tool. This will prevent both moisture and dust inside the hose from entering the tool
and causing possible rust or malfunction.
1.Using these tools in any potentially explosive environment is strictly prohibited.
2.It is always recommended that these types of tools must be operated when standing
on a solid or rm location.
3.Always use these tools in a well ventilated area.
4.Slipping, stumbling and falling are the major causes of potential serious injury,
therefore, a clean and clutter free surface in the working area before operating the
tools is strongly recommended.
Read this manual carefully before installing, operating,
servicing or repairing.
Working environment:
Air supply and connection requirements:
2
Ideal system connection:
Piping diameters and length requirement:
The diameter ΦA required for the inlet pipe is recommended on the specication table.
The diameter ΦB required for the branch pipe (from to ) should be 2 times as large as ΦA.
ΦB = 2 x ΦA
The diameter ΦC required for the primary air supply (from to ) should be 3 times as large as
ΦA. ΦC = 3 x ΦA
The length for the inlet pipe should be less than 15 feet (4.5m).
3
1. This tool should only be used as a hand operated tool. It is powered by compressed air and is not insulated against
electric shock.
2. This tool is specially designed for drilling holes. Any application or use of this tool other than what it is designed for is
strictly prohibited.
3. High sound levels may cause hearing damage. Always wear hearing protection when operating this tool.
4. User must wear proper clothing. Loose clothing, long hair, stings, straps, belts and jewelry should not be worn when
operating this tool.
5. Make certain to stand on a solid or rm location and keep body in well-balanced position while operating this tool.
6. The reaction force created during operation can be reduced efciently by means of attaching an extra handle onto this
tool. Which measure can minimize the potential hazard caused by the reaction force.
7. Make sure that the drill bit is correctly mounted and tightened before use.
8. Ensure that the chuck key is removed from the tool before starting.
9. Ensure that the work piece is supported or xed properly before operating.
10. Do not apply too much force on the tool because it may create a hazard at the moment when the drill bit breaks
through the workpiece.
11. Note that high reaction torque may develop due to drill bit stalling. This may happen when drilling into the material or
when the drill bit breaks through the material.
12. Beware of unexpected movement during operation, such as drill bit failure, which may create a hazards condition and
cause injuries.
13. To prevent an accidental starting hazard, always rest the idle drill in a stable position.
14. Release the throttle trigger to avoid danger if there is a failure of energy supply and when connecting or disconnecting
the air hose.
15. Beware if the compressed air hose breaks unexpectedly, or is being connected or disconnected improperly. This
whipping action may cause injury.
16. Always turn off the air supply and disconnect the air hose before replacing drill bit or making adjustments on this tool.
17. Prolonged use will cause user fatigue. Periodic breaks are recommended for user safety.
18. It is recommended to stop operating the tool whenever the user experiences discomfort, tingling or pain during use.
19. Make sure there is no gas or combustible material stored near the tool when servicing, changing insert tools, or
storage.
20. Avoid storing this tool where it is subject to high humidity.
Warning:
4
1. Before connecting the air hose to this tool or after
operating, apply 4 or 5 drops of pneumatic oil into the
air inlet and run it for several seconds, referring this
operation to the attached picture.
2. Maintain this tool regularly by performing the same
oiling application every 3 to 4 hours of operation.
3. Do not lubricate tools with ammable or volatile liquids.
Use only the lubricant recommended by Mighty-
Seven or authorized dealers. Any other lubricant will
lead to reduce performance of the tool and permanent
damage. Whenever any unauthorized lubricant is used
by accident, flush it immediately with recommended
pneumatic oil.
4. Follow all the recycling laws of waste disposal once
this tool is no longer usable.
Maintenance:
Pneumatic oil
Air inlet
Regular maintenance
29
Uncertainty K=0.5a if a < 5 m/s² or K=0.4a if a>5 m/s²
Référence
inch
Incertitude K=0.5a si a < 5m/s² ou K=0.4a si a>5m/s²
Artikel-Nr.
Unsicherheit K = 0,5, wenn ein < 5 m/s² oder K = 0.4a, wenn a> 5 m / s²
mm
mm
mm
L/min
L/min
mm
mm
kg
kw
bar
bar
inch
mm
mm
dBA
dBA
dBA
m/s
2
m/s
2
m/s
2
Diamètre
du mandrin
Bohrfutter
Cons. D'air
moyenne
Luftverbrauch
Niveau de
vibration
Longueur
Gesamtlänge
Poids
Nettogewicht
Vibrationsniveau
Pression
Arbeitsdruck
Vitesse
à vide
Leerlauf
Drehzahl
Niveau
sonore
Schalldruckpegel
Tuyau
d'air
Empf.
Luftschlauch
Chuck Size
QE-331 10 1800 6.5 90 8" 2.42 3/8" 96.5 0.3
QE-332 10 2200 6.5 90 7-1/2" 2.20 3/8" 96.5 0.3
QE-333 10 1800 6.5 90 8" 2.42 3/8" 92 0.2
QE-334 10 2200 6.5 90 7-1/2" 2.42 3/8" 92 0.2
QE-341 13 800 6.5 90 9" 3.96 3/8" 96.5 0.1
QE-342 13 800 6.5 90 8-1/4" 3.74 3/8" 96.5 0.1
QE-343 13 800 6.5 90 9" 3.96 3/8" 97.5 0.1
QE-344 13 800 6.5 90 8-1/4" 3.74 3/8" 97.5 0.1
QE-731 10 1800 3.2 90 7-5/8" 2.42 3/8" 90 0.3
QE-331 10 1800 184 6.3 203 1.1 10 96.5 0.3
QE-332 10 2200 184 6.3 190 1.0 10 96.5 0.3
QE-333 10 1800 184 6.3 203 1.1 10 92 0.2
QE-334 10 2200 184 6.3 190 1.0 10 92 0.2
QE-341 13 800 184 6.3 230 1.8 10 96.5 0.1
QE-342 13 800 184 6.3 209 1.7 10 96.5 0.1
QE-343 13 800 184 6.3 230 1.8 10 97.5 0.1
QE-344 13 800 184 6.3 209 1.7 10 97.5 0.1
QE-731 10 1800 90.6 6.3 195 1.1 10 90 0.3
QE-331 10 1800 184 6.3 203 1.1 10 96.5 0.3
QE-332 10 2200 184 6.3 190 1.0 10 96.5 0.3
QE-333 10 1800 184 6.3 203 1.1 10 92 0.2
QE-334 10 2200 184 6.3 190 1.0 10 92 0.2
QE-341 13 800 184 6.3 230 1.8 10 96.5 0.1
QE-342 13 800 184 6.3 209 1.7 10 96.5 0.1
QE-343 13 800 184 6.3 230 1.8 10 97.5 0.1
QE-344 13 800 184 6.3 209 1.7 10 97.5 0.1
QE-731 10 1800 90.6 6.3 195 1.1 10 90 0.3
31
EC DECLARATION OF CONFORMITY
.
Original Language
Serial Number: Please refer to the tool
Air Drills
Item No.: QE-131 QE-231 QE-331 QE-332 QE-333 QE-334 QE-341 QE-342
QE-343 QE-344 QE-621 QE-731
6.3 bar (90. psi)
We declare under our own responsibility that the above machinery fulls all the
relevant provisions of (MD) Machinery Directive 2006/42/EC and its amendment
and is manufactured and tested according to the following standards:
EN ISO 11148-3 / EN ISO 15744 / EN ISO 28927-5
Declared in: Taichung, Taiwan
Dated:2013/06/01
Jonney Chen
Declared by: QA Manager
Manufacturer:
Mighty Seven International Co., Ltd.
No. 70-25,Ching Qunag Rd., Wu-Jih Shiang,
Taichung Hsien, 41466 Taiwan
www.mighty-seven.com
Authorized contact, to compile the technical les :
King Tony France
3 Rue des imprimeurs ZI République Nord 1.
86000 POITIERS FRANCE
TEL
(+33) 5-49-30-30-90
E-MAIL
christian.aubineau@kingtony.eu
Signature
37
.
Typ výrobku: QE-131 QE-231 QE-331 QE-332 QE-333 QE-334 QE-341 QE-342
QE-343 QE-344 QE-621 QE-731 Vzduchové vrtačky
6.3 bar (90. psi)
Na svoji vlastní zodpovědnost prohlašujeme, že výše uvedené pneumatické nářadí
splňuje všechny příslušné požadavky směrnic 2006/42/EC a jejich změn a že je
toto nářadí vyráběno a testováno podle následujících standardů:
EN ISO 11148-3 / EN ISO 15744 / EN ISO 28927-5
Prohlášeno v: Taichung, Taiwan
Dne: 2013/06/01
Jonney Chen
Deklarováno: QA Manager
Manufacturer:
Mighty Seven International Co., Ltd.
No. 70-25,Ching Qunag Rd., Wu-Jih Shiang,
Taichung Hsien, 41466 Taiwan
www.mighty-seven.com
Authorized contact, to compile the technical les :
King Tony France
ANCIEN BATIMENT CAPLAIN 3 RUE DES IMPRIMEURS ZI
REPUBLIQUE NORD 86000 POITIERS FRANCE
TEL
:
(+33) 5-49-30-30-90
E-MAIL
:
christian.aubineau@kingtony.eu
Paraksts
PROHLÁŠENÍ O SHODĚ PRO EU
47
QE-731
NO. PART NO. DESCRIPTION QTY
01 QE-731P01 Motor Housing 1
02 QE-731P02 Gasket 1
03 QE-731T03 Bearing 626 (2pcs) 1 set
04 QE-731T04 End Plate (2pcs) 1 set
05 QE-731P05 Pin 1
06 QE-731P06 Cylinder 1
07 QE-731P07 Rotor 1
08 QE-731T08 Blade (5pcs) 1 set
09 QE-731P09 Bearing Case 1
10 QE-731T10 Planet Gear (3pcs) 1 set
11 QE-731T11 Pin (3pcs) 1 set
12 QE-731P12 Gear Complete 1
13 QE-731P13 Annular Gear 1
14 QE-731T14 Bearing 6201 (2pcs) 1 set
15 QE-731P15 Gear Housing 1
16 QE-731P16 Chuck Spacer 1
17 QE-3C Keyless Drill Chuck 1
18 QE-731P18 Screw 1
19 QE-731P19 Pin 1
20 QE-731P20 "O"-Ring 1
NO. PART NO. DESCRIPTION QTY
21 QE-731P21 "O"-Ring 1
22 QE-731P22 Valve Stem 1
23 QE-731P23 Reverse Bushing 1
24 QE-731P24 "O"-Ring 1
25 QE-731P25 Reverse Lever 1
26 QE-731P26 Valve Spring 1
27 QE-731P27 Trigger 1
28 QE-731P28 Screw 1
29 QE-731P29 Exhaust Diffuser 1
30 QE-731T30 Screw (2pcs) 1 set
31 QE-731P31 Air Inlet 1
32 QE-731P32 Wave Washer 1
33 QE-731P33 Grip Cove 1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

M7 QE-131 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI