WFLY ET07 is a versatile and user-friendly remote control system designed for various models including helicopters, airplanes, multi-rotors, vehicles, and ships. With its 10 channels, full 4096 resolution, and 2.4GHz bidirectional transmission, it offers precise control and reliable communication. The ET07 features a 3.5-inch touch screen for intuitive navigation and programming, along with a range of customizable functions such as digital trims, switches, and levers.
WFLY ET07 is a versatile and user-friendly remote control system designed for various models including helicopters, airplanes, multi-rotors, vehicles, and ships. With its 10 channels, full 4096 resolution, and 2.4GHz bidirectional transmission, it offers precise control and reliable communication. The ET07 features a 3.5-inch touch screen for intuitive navigation and programming, along with a range of customizable functions such as digital trims, switches, and levers.
ET07
使用安全注意事项
Beginners should pay particular attention to the following safety precautions! Please
read carefully!
It is forbidden to fly when in poor condition such as fatigue and drunkenness.
It is forbidden to fly in bad weather such as rain and gale.
It is forbidden to fly near high voltage lines, communication base stations and places where people gather or activate.
It is forbidden to fly in airports and other places where fly is forbidden.
Before flying, test the equipment, check whether the transceiver system and the aircraft are normal;
When flying, make the interface of transmitter in the initial interface for preventing the change of parameters by mistake;
After flying, turn off the receiver primarily and then turn off the transmitter for protecting people from the fail-safe function.
The sequence of power on and off of transmitter and receiver!
Power on:
First Turn on the transmitter (ensuring the minimum throttle position)
Second Turn on the receiver
Power off:
First Turn off the receiver
Second Turn off the transmitter
Use guaranteed and special charger to charge the battery
Preserve the battery with special case for safety
The electronic product should be dry, use alcohol and special cleaner to clean.
Do not force the vulnerable antenna, or it may destroy.
The screen is vulnerable, do not press firmly or shave with sharp things.
Please take care of the product! It can not be placed under sun or in high temperature, wet or dusty place.
Charge and attentions
ET07 charge with 1S lithium battery. Charge with other kinds of batteries may damage remote control.
Please charge with standard micro USB interface 5V/1.5A power adapter.
After-sales service
Please log in official website: http://en.wflysz.com for detailed information.
Or email us at service@wflysz.com
Receiver
Model: RF207S
Frequency: 2.4 GHz
Working Voltage: 3.7 V-8.4 V
Working Current: 75 mA
Applications: Helicopter, Airplane, Multi-Rotors, Vehicle,
Ship
Resolution: Full Channel 4096 Resolution
PWM: 7 Channel (Mode A)
PPM: Support
W.BUS: Compatible with S.BUS
W.BUS2: Telemetry Sensor Input
Bidirectional Transmission: Support
Fail Save: Support
Online upgrade: Support
External voltage detection: DC 0-96V
Size: 27×14×51mm
Weight: 14.6g
Switch
Power switch: press for about 2 seconds to turn on or turn off.
T1 ~ T4: digital trim (user-defined)
SA: long lever, 2 positions, alternate (user-defined)
SB: short lever, 3 positions, alternate (user-defined)
SC: short lever, 3 positions, alternate (user-defined)
SD: long lever, 2 positions, momentary (user-defined)
V1: rotary knob (user-defined)
V2: thumb wheel (user-defined)
HOME: functional key. Press to return to standby interface;
press for 2 seconds, open monitor interface.
EXIT: return key. Press to return to the previous interface;
press for 2 seconds, lock/unlock the touch screen
＋: increase, toggle state
－: decrease, toggle state
Navigation button:
The middle key: press to confirm, press and hold to reset
parameters (value)
Transmitter
Model: Et07
Channel: 10 channels
Working voltage: 3.7V (1S Lithium battery)
Working current: ≤260mA
Applications: Helicopter, Airplane, Multi-Rotors, Vehicle,
Ship
Resolution: Full Channel 4096 Resolution
Band: 2.4GHz (Bidirectional)
Frequency Hopping: New FHSS Frequency Hopping (64
points, 3.6ms)
Storage: 20 models
Programming: 5 Groups Mixed Control
Language: Chinese, English
Upgrade: USB online upgrade
Display: 3.5inch touch, 480*320, TFT color display
SA
SB
Function buttons
Trainer interface
Antenna
Trim T4
Trim T3
Power light
RF light
SD
SC
V2
V1
Trim T1
Navigation button
Power switch
USB interface
Touch screen
Stick
Hook
Trim T2
EN V01
Home Screen
1. Transmitter Model
2. WFLY: Click to Enter Main Menu
3. Ordinary Timer: Press and hold to Reset, Click to
Start/Stop
4. Mode Timer: Press and hold to Reset, set in [Timer] menu
5. Voltage: Receiver Voltage, External Battery Voltage
6. Trimming Monitor: Display real-time Trimming State
7. Time: accumulation of time after booting. Reset after
power off.
8. Model name: click into the model selection interface
9. Model: click into the current model type interface
10. User name: click into custom naming
11. Trimming state: display T1 ~ T4 state (when T1-T4 use as
switch), for details, refer to the instruction in [Aux Channel] and
[Trim Step] of general function.
Means up
Means neutral
Means down
12. Power: Transmitter battery level
13. Receiver signal strength
14. Fly Mode (throttle hold, ordinary, idle 1, idle 2)
15. Mixed control: display as mixed control function is on
16. Working mode: current mode (trainer, simulator, student)
17. Screen locking state (press EXIT key for 2 seconds to
toggle)
6
5
4
3
2
1
14
15
16
9
10
11
8
7
12
13
17
SI M
RX
NO R M
MI X
4.2V
ET07
00 : 06 : 59
0
0
0
0
Model 1
Rx:5. 0 V Ext:1 2 V
User Na m e
T4
T3
T2
T1
PRODUCT PARAMETER
ET07 INTERFACE
SUMMARY MANUAL
WARNING AND NOTICE ON INTERFACE
LED Status
Power light: on, power on or charging; off, power off
RF light: OFF RF LIGHTS RF FLASH
模拟器
RX
混控
4.2V
00:06:59
模拟器
RX
混控
4.2V
00:06:59
NORM
Linkage Setting
General Menu Model Menu
Menu
System setting
模拟器
RX
混控
4.2V
00:06:59
NORM
Link
Range Check
Fail Safe
W.BUS Servo
PPM/W.BUS
Telemetry
Link ag e Setting
Servo Frequency
模拟器
RX
混控
4.2V
00:06:59
NORM
Link
ON
Telemetry
Link
Start
Mode A
Mode
RX
NORM
4.2V
THR
RUD
AIL
ELE
00:06:60
1
Mode
Stic k Mo de
RX
NORM
4.2V
Menu
System setting Linkage Setting
Model MenuGeneral Menu
00:06:60
RX
NORM
4.2V
Syst em S etting
00:06:60
Language
User Name
Back Color
Factory Reset
Screen Cal
Trainer
Calibration
Stick Mode
00:06:60
RX
NORM
4.2V
Menu
0
0
0
0
Mo d e l1
Rx:5.0V Ext:12V
Us e r N am e
T4
T3
T2
T1
RX
NORM
4.2V
00:06:59
Model Copy
Model Name
Model Reset
Model Type
Model Select
Syst em S etting
Low Voltage
Sound
Backlight
System setting Linkage Setting
Model MenuGeneral Menu
RX
NORM
4.2V
Menu
00:06:59
RX
NORM
4.2V
00:06:59
Mode l Typ e
Helicopter
Ty pe
Confirm
00:06:60
RX
NORM
4.2V
Menu
0
0
0
0
Mo d e l1
Rx:5.0V Ext:12V
Us e r N am e
T4
T3
T2
T1
Power off, student or
stimulator mode
Connected, trainer or
normal mode
Linking state
Interface And Buzzer Warning
1. Low voltage warning
The battery voltage is low when turn on, the buzzer alarms and the screen turns to warning interface, press 'yes' , power on as usual;
press 'no', power off.
The battery voltage is low when use, the buzzer alarms, the voltage value flashes on upper right corner (voltage is low) or on lower left
corner (receiver or external voltage is low) of the screen.
2. The position of throttle stick
when power on, the buzzer alarm until the stick is at the lowest position.
press 'yes' on the warning interface or pull the throttle at the lowest position to power on as usual.
3.The wrong position of switch
The warning interface will show the corresponding switch which is not on the default position.
4.Conflict of mix-control function
Some of the function can not be mixed, the warning interface pop-up and return automatically
5.Power off
After open the telemetry function, when the transmitter is turned off, whether the receiver is communicating or not will be checked, if it is
still communicating, the warning interface pop-up for ensuring and the equipment can be turned off.
6.The warning tone of linkage
When link successfully, the buzzer alarm once, when timed out, the buzzer alarm once and quit link state.
7.Trim
When trim at the midpoint or endpoint, the buzzer long alarm once.
Link
When Linking, do not connect the power equipment or dismantle the propeller. Caution!
Setting method:
1.Charge the receiver and press 'SET' button for 3 second, the orange light flickers.
2.For transmitter, press 'start' bouton to link: WFLY→Linkage setting→Link→press"start"
3.When successfully linking, the RF light of transmitter is on, the green light of receiver is on
(W.BUS mode), or the blue light is on (PPM mode).
Cautions:
1.The distance between transmitter and receiver must be near (less than 1 meter).
2.Linking cannot be operated when transmitter is in Simulator, Student mode (System Setting→
Trainer);
3.There is no other WFLY 2.4 GHz systems linking nearby.
4.When linking, press 'cancel' or return button to quit if necessary.
5.Connection and validation must be done after linking.
6.Only when the telemetry function is on during linkage can the information be obtained, and the
protection function is on when power off at the same time
Validation: After linking, the server can synchronously reacts follow the order.
Mode
The default is 'mode A’
Fail-safe
The importance of Fail-safe:
Reduce the rate of injury when the aircraft lost control.
Advice: set fail-safe data first before each debugging or trial flying.
Steps:
1. Linkage Setting → Fail Safe, to enter the interface
2. Set mode:
HOLD: the servo maintains its last commanded position.
F/S: fail-safe mode, servo moves to a predetermined position.
OFF: cut current channel (only for part of special modes or parts FC detect port)
3. Set fail-safe value: F/S value can only be set under F/S mode, click numeric frame for current channel value.
Attention: for safety, you can refer to following suggestion or consult after-sales service.
The parameter suggested
1. For helicopter, throttle set to lowest value, other channels set as set as smooth flight mode
2. Lowest or ldle down, other channels set as smooth mode or hovering, because airplane/glider can slip down without power!
3. For multicopter, please refer to FC manual.
(only for suggestion, specific settings are based on actual situation)
Model Settings
Method:
Main menu→ System Setting → Model Type
Save:
Select model and Click 'ok' to confirm, click 'yes' of hint to save
Attention: to preserve the parameter of former model, please use 'model copy' function. This function may reset the parameter.
Stick Setting
You can select the control way according to habits.
Method:
Main menu→ System Setting → Stick Mode
Save:
Select mode (1,2,3,4) and save.
0% 0%
0% 0%
-152% 0%
0%
0%
0%
0%
AIL
FLP
ELE
CH7
THR
CH8
CH9
CH10
RUD
GEAR
F/S F/S
F/S F/S
F/S F/S
F/S
F/S
F/S
F/S
MODE MODE
F/ S F/ S
00:06:59
RX
NORM
4.2V
Fail S af e
-
1
-
2
WFLY ET07 is a versatile and user-friendly remote control system designed for various models including helicopters, airplanes, multi-rotors, vehicles, and ships. With its 10 channels, full 4096 resolution, and 2.4GHz bidirectional transmission, it offers precise control and reliable communication. The ET07 features a 3.5-inch touch screen for intuitive navigation and programming, along with a range of customizable functions such as digital trims, switches, and levers.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI