RESET
MUTE
EQ
VOL+
VOL-
AUD
USB
BT
ARC
OPT
10987 11
660x173mm
105G
110x86.5mm
30709L003102-003
SOUNDBAR
HTL2060
User manual
SOUNDBAR
HTL2060
User manual
System positioning :
The subwoofer is recommended to be put
Helpful Hint:
- To avoid magnetic interference, do not position
the speakers, too close to your TV.
Playing the speakers and subwoofer
Audio source / player
SOUNDBAR
The soundbar is recommended to be put on
the at desktop to get a better acoustic eect.
Warranty
1. Proof of purchase is not accompanied with this warranty card.
2. The warranty card is not completed immediately after purchase.
3. The apparatus is not used according to this user manual.
4. Defects are caused due to improper or reckless use.
5. Any repairs are done by persons other than Philips authorized service centre.
6. The serial number is tampered with.
7. Defects due to causes beyond control like lightning, abnormal voltage or while in transit to the
purchaser’s residence.
Product Sl. No.
Model No.
Invoice Number
Date of Purchase: / /
Customer’s Name and address:
PIN:
Always there to help you!
Visit us at www.support.philips.com
Helpline: 1800 425 6396
Email: india.callcentr[email protected]
(10 a.m. to 9 p.m. Mondays to Saturdays & 10
a.m. to 6 p.m. on Sundays)
Dealer Name & Stamp:
This Philips soundbar is warranted against any defect due to defective materials or workmanship for 12 months
from the date of purchase, should a defect develop during the warranty, TPV Technology India Pvt. Ltd.,
its authorized service center in India.
FREE OF CHARGE at any of
General information
Safety instructions
Please read carefully the safety mark on the back side
This mark is intended to alert the user from
the non isolated dangerous voltage within the
constitute a risk of electric shock to persons.
This mark is intented to alert the user for
important operating and servicing instruction.
Warnings
•
Avoid sustained periods on high-volume use, and
do not turn the volume to maximum level while using
high output signal, such as Mobile Phone or DVD,
etc., as this will cause distortion and may damage the
loudspeaker cones.
•
when not in use.
• Do not open the cover or back panel to avoid
electrical shock or any other accidents. No user-
serviceable parts are inside.
• Only for indoor use.
• Plug the system to the AC outlet with the right voltage
marked on the back panel of the Subwoofer and soundbar.
• The MAINS plug is used as the disconnect device, the
disconnect device shall remain readily operable.
Accessories
The product shall not be exposed to dripping or splashing
be placed on the product.
•
Connections
Soundbar back panel
Top panel operation
Remote controls
* AVAILABLE IF CONNECTED* AVAILABLE IF CONNECTED
Bluetooth Operating Instruction
1. Press SOURCE key from soundbar or remote control to Bluetooth mode;
2. When selecting Bluetooth mode, BT light will start blinking and you will hear an audio tone which Bluetooth
pairing mode.
3. For pairing with mobile phone or other Bluetooth devices, search the device named “Philips HTL2060” and
choose to pair. Once paired, the BT light will slowly ash and come up with another audio tone. BT light will
stop ash when playing music.
4. Press and hold “ ” for 3 seconds from remote control in order to force disconnect the
Bluetooth connection.
Note: While using Bluetooth, if external call comes, then speaker system goes in mute mode in
order to protect privacy of mobile phone user. Operation resumes once the call is disconnected.
Troubleshooting
Problem Solution
1. No power.
2. No sound or distorted sound.
3. The remote control does not
function properly.
4. Low hum or buzz sound.
drive cannot be read.
6. Slow operation of the USB
Check if the AC power cord is properly inserted into the AC mains socket.
Adjust the volume / select the correct source to choose the equipment
that you want to hear through the system.
Reduce the distance between the remote control and the system. Replace
the batteries with new ones / Point the remote control directly towards the
IR sensor (located on front panel of the subwoofer) / Check that the batteries
Place the product as far away as possible from electrical devices that may be
causing interference / Check power supply voltage and consult electrician.
Drive is
7. BT not working. Reduce the distance or device is not paired.
Warning -
Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty.
below before taking the system for repair. If you are unable to remedy the problem by following hints
mentioned in below table.
and play. / Take out USB drive and insert it again properly.
1. 2. RESET 3. MUTE 4. VOL+ 5. 6. 7.
8. VOL- 9. BT 10. ARC 11. OPT 12. AUD 13. USB 14. EQ
1. : Power ON or Standby mode.
2.RESET: To set the EQ and volume to default level.
3. MUTE: Turn volume o, short press again to activate the sound.
4. VOL+: To increase the Volume by short or long press VOL+.
5. : Play the previous song by pressing “ ” but not in audio mode.
6. : Play/ pause in USB*/BT mode and MUTE in audio mode.
7. : Play next song by pressing “ ”, but not in audio mode.
8. VOL-: To decrease the Volume by short or long press VOL-.
9. BT: Bluetooth mode.
10. ARC: HDMI ARC mode.
11. OPT: Optical mode.
12. AUD: Audio input mode.
13. USB: USB* mode.
14. EQ: POP, ROCK, JAZZ, CLASSIC, COUNTRY, NORMAL.
(1)
(2)
(8)
(4)
(5)
(9)
(14)
(12)
(3)
(7)
(10)
(11)
(13)
(6)
1. Bass connection.
2. Input Connect to sound sources such as computer, CD player, MP3, etc.
3. Headphone output.
4. Optical Input.
5. HDMI ARC Input.
(1)
(2)
(3)
(4)
(5)
1. /SOURCE
2.
3. /VOL-
4. /VOL+
5.
1. /SOURCE: The Speaker system is in stand by mode when power on,
with LED lights on. Please press the “ /SOURCE” to select
appropriate source. Keeping the “ /SOURCE” key pressed for long
will put it back in stand by mode.
You can toggle through the input modes by pressing the “ /SOURCE”
key. “BT” denotes Bluetooth Mode, “ARC” denotes HDMI ARC Mode,
“OPT” denotes Optical Mode, “ AUDIO IN ” denotes Audio Mode,
“ ” denotes USB* mode.
2. : Play/Pause the songs.
3. /VOL-: Long press for volume decrease/ short press for prev track.
4. /VOL+: Long press for volume increase/ short press for next track.
5. : USB* Slot.
Item Remote control User manual
Quantity 1
Audio-2RCA cable
1 1 1
Optical cable
1
Connection cable
Total system power 60W RMS
Soundbar power 15 x2W RMS
Subwoofer power 30W RMS
Separation
SNR
Audio input socket Audio-2RCA cable
Power consumption
12.7 W
Subwoofer 1 Way
Speaker size 5.25 inches
Impedance 4 Ohm
Frequency range 60Hz - 150Hz
Dimension (mm) W x H x D
120 x 380 x 260
Weight 2.88kg
Soundbar
Speaker size
Impedance
Frequency range
Product Dimension (mm) W x H x D
Net Weight
BT version V5.0
437x 88 x 62
2 Way
2.25 inches * 2
8 Ohm
140Hz - 20KHz
1.20 kg
BT range
USB max capacity
playability
Up to 32GB
Up to 10 meters
MP3 track
>55db
>40db
*** Do NOT use USB for char ging devices which c an cause damage to
your exter nal devices.thank you.
U S B
(4)
(3)
(1)
(2)
(5)
Care and safety information
Avoid high temperatures, moisture, water and dust
•
Apparatus should not be exposed to dripping or
splashing of liquid.
• Do not place any source of danger on the Subwoofer,
• Do not install near heat sources.
Do not block any ventilation opening
•
Place the apparatus in a location with adequate
ventilation to prevent internal heat build up. Allow at
least 10cm (4 inches) of free space all around the
apparatus for adequate ventilation.
• At high volume the back cover of Subwoofer becomes
hot. Do not touch it.
Care of the cabinet
•
Use a soft cloth slightly moistened to clean the cabinet.
Do not use a solution containing alcohol, spirits,
ammonia or abrasives.
•
Attention should be drawn to the environmental
aspects of battery disposal.
• Batteries shall not be exposed to excessive heat such as
Remark:
In order not to disturb in the dark, the LED display of soundbar is set to be o,
if there is no operation after 90 seconds of stand by mode.
Remark:
In order not to disturb in the dark, the LED display of soundbar is set to be o,
if there is no operation after 90 seconds of stand by mode.
AUDIO IN
BASS
OPT
ARC
/