Blaze BLZ-GRIDDLE-CART Owner's manual

Brand: Blaze

Model: BLZ-GRIDDLE-CART

Category: Car kits

Type: Owner's manual

This manual is also suitable for

BLAZE Instructional Book

Page | 1

Version 1.0

Blaze Griddle Cart

USE & CARE GUIDE

Model #: BLZ-GRIDDLE-CART

ATTENTION:

INSTALLER: PLEASE LEAVE THESE INSTRUCTIONS WITH THE CONSUMER.

CONSUMER: PLEASE READ & RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE AND

BEFORE INSTALLING AND OPERATING.

- CONTACT INFORMATION -

Blaze Outdoor Products: 6620 Greenwell Springs Rd, Baton Rouge, LA 70805 USA

Phone: 866-976-

9510

email: CustomerService@BlazeGrills.com

WWW.

BLAZEGRILLS.COM

BLAZE Instructional Book

Page | 2

Version 1.0

Parts Included

• 4 - Caster wheels

• 1- Large screw pack for wheels (16 screws, lock washers, and flat washer)

• 1 -Small screw pack for propane support and lid holder (4 screws)

• 1 - Drain and plug

• 2 - Drawer hole cover caps for insulated drawer

• 3 - Door and drawer handle kits with screws

• 1 - Propane support bolt and bracket

• 1- lid holder bracket

• 1- Condiment tray with food containers

Tools needed

• Philips head screwdriver

• Channel locks

Instructions

Step One: Installing Cater Wheel

1. You will need (4) caster wheels and (16 each) longer screws, lock washer, and flat

washer.

2. Install wheels to bottom of cart (locking wheels maybe in any location).

3. Slide lock washer on screw, then flat washer, then screw to cart.

Step Two: Assembling Top Drawer

1. You will need (1) handle kit with included screws.

2. Using access openings on inside, install screws into handle.

Note: Drawer may be removed using red tabs on rail system.

BLAZE Instructional Book

Page | 3

Version 1.0

Step Three: Assembling Lower Insulated Drawer

1. You will need (1) handle kit with included screws, (2) drawer hole cover caps, (1) drain.

2. Using access openings on inside (use screw driver to poke hole through the foam

insulation) install screws into handle.

3. Install both drawer hole cover caps (keeps drawer insulated).

4. Install drain (drain and rubber washer go through top, nut underneath). Hand tighten nut

then use channel locks to make a ¼ turn.

Note: Drawer may be removed using red tabs on rail system.

Step Four: Installing Propane Tank Support Bolt

1. You will need (1) propane support bolt and bracket, and (2) shorter screws.

2. Using the two holes located in front of propane tank opening on floor of cart, hold bracket

under the cart lining up hole and install screws.

Step Five: Installing Lid Holder Bracket

1. You will need (1) lid holder bracket (See figure below), and (2) shorter screws.

2. Using two holes on back of cart to the right of the opening for gas inlet, install bracket

using screws making sure the lip of the bracket is facing up.

BLAZE Instructional Book

Page | 4

Version 1.0

Step Six: Assembly of Condiment Tray

1. You will need (1) stainless trey and white food containers.

2. Match cups with cutout on tray, place in bottom insulated drawer.

Note: Remove all white protective plastic from cart,

drawers, door, lid holder, and condiment tray.

Blaze BLZ-GRIDDLE-CART Owner's manual

Brand: Blaze

Model: BLZ-GRIDDLE-CART

Category: Car kits

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Blaze BLZ-GRIDDLE-CART Owner's manual

This manual is also suitable for

Blaze BLZ-GRIDDLE-CART Owner's manual

Related papers

Other documents