Seagate 1TB SATA, 7200rpm User manual

Product Manual

Constellation

®

ES.1 Serial ATA

100650923

Rev. B

March 2011

Standard Models

ST2000NM0011

ST1000NM0011

ST500NM0011

Self-Encrypting Drive Models

ST2000NM0031

ST1000NM0031

ST500NM0031

SED FIPS140-2 Models

ST2000NM0051

ST1000NM0051

ST500NM0051

Revision history

Publication number: 100650923, Rev. B, March 2011

Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology

LLC in the United States and/or other countries. Constellation ES.1 and SeaTools are either trade

-

marks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the

United States and/or other countries. The FIPS logo is a certification mark of NIST, which does not

imply product endorsement by NIST, the U.S., or Canadian governments. All other trademarks or

registered trademarks are the property of their respective owners.

No part of this publication may be reproduced in any form without written permission of Seagate

Technology LLC. Call 877-PUB-TEK1 (877-782-8351) to request permission.

One gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your

computer's operating system may use a different standard of measurement and report a lower

capacity. In addition, some of the listed capacity is used for formatting and other functions, and thus

will not be available for data storage. Seagate reserves the right to change, without notice, product

offerings or specifications.

Revision Date Sheets affected or comments

Rev. A 02/24/11 Initial release.

Rev. B 0323/11 25, 30-32 & 35.

Constellation ES.1 Serial ATA Product Manual, Rev. B i

Contents

1.0 Seagate Technology support services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.1 Specification summary tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.2 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.2.1 LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.3 Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.4 Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.5 Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.6 Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.7 Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.8 Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.8.1 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.8.2 Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.8.3 Voltage tolerance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.8.4 Power-management modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.9 Environmental limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.9.1 Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.9.2 Humidity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.9.3 Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.9.4 Shock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.9.5 Vibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.10 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.11 Test for Prominent Discrete Tones (PDTs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.12 Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.13 Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.13.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) . . . 22

3.14 Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.14.1 Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.14.2 Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.14.3 FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.15 Environmental protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.15.1 European Union Restriction of Hazardous Substances (RoHS) Directive. . . . . 24

3.15.2 China Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . 24

3.16 Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.17 Reference documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.18 Product warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

4.0 Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4.1 Handling and static-discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4.2 Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4.3 Serial ATA cables and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4.4 Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

5.0 About FIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

6.0 About self-encrypting drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

6.1 Data encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

6.2 Controlled access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

6.2.1 Admin SP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

6.2.2 Locking SP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6.2.3 Default password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6.3 Random number generator (RNG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

ii Constellation ES.1 Serial ATA Product Manual, Rev. B

6.4 Drive locking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6.5 Data bands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6.6 Cryptographic erase. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6.7 Authenticated firmware download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6.8 Power requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6.9 Supported commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6.10 RevertSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6.11 ATA Security Erase Unit Command on SED SATA drives . . . . . . . . . . . . . . . . . . . . . . . . 32

6.12 Sanitize Feature Set on SED Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

7.0 Serial ATA (SATA) interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

7.1 Hot-Plug compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

7.2 Serial ATA device plug connector pin definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

7.3 Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

7.3.1 Identify Device command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

7.3.2 Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

7.3.3 S.M.A.R.T. commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Constellation ES.1 Serial ATA Product Manual, Rev. B iii

List of Figures

Figure 1. Typical 2TB model 5V & 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . 12

Figure 2. Typical 1TB model 5V & 12V startup and operation current profiles . . . . . . . . . . . . . . . . . . . 13

Figure 3. Location of the HDA temperature check point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 4. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Figure 5. Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Figure 6. Example of FIPS tamper evidence labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Constellation ES.1 Serial ATA Product Manual, Rev. B 1

1.0 Seagate Technology support services

SEAGATE ONLINE SUPPORT and SERVICES

For information regarding products and services, visit http://www.seagate.com/www/en-us/about/contact_us/

Available services include:

Presales & Technical support

Global Support Services telephone numbers & business hours

Authorized Service Centers

For information regarding Warranty Support, visit

http://www.sea

gate.com/www/en-us/support/warranty_&_returns_assistance

For information regarding Data Recovery Services, visit http://www.i365.com

For Seagate OEM & Distribution partner portal, visit https://direct.seagate.com/portal/system

For Seagate reseller portal, visit http://spp.seagate.com

2 Constellation ES.1 Serial ATA Product Manual, Rev. B

2.0 Introduction

This manual describes the functional, mechanical and interface specifications for the following Seagate

Constellation

®

ES.1 Serial ATA model drives:.

Note. Previous generations of Seagate Self-Encrypting Drive models were called Full Disk Encryption

(FDE) models before a differentiation between drive-based encryption and other forms of encryp

-

tion was necessary.

Note. The Self-Encrypting Drive models indicated on the cover of this product manual have provisions for

“Security of Data at Rest” based on the standards defined by the Trusted Computing Group (see

www.trustedcomputinggroup.org).

For more information on FIPS 140-2 Level 2 certification see See Section 5.0 on page 29 .

These drives provide the following key features:

• 7200 RPM spindle speed.

• PowerChoice™ for selectable power savings

• Top Cover Attached motor for excellent vibration tolerance

• High instantaneous (burst) data-transfer rates (up to 600MB per second).

• Perpendicular recording technology provides the drives with increased areal density.

• State-of-the-art cache and on-the-fly error-correction algorithms.

• Native Command Queueing with command ordering to increase performance in demanding applications.

• Full-track multiple-sector transfer capability without local processor intervention.

• SeaTools™ diagnostic software performs a drive self-test that eliminates unnecessary drive returns.

• Support for S.M.A.R.T. drive monitoring and reporting.

• Supports latching SATA cables and connectors.

• Worldwide Name (WWN) capability uniquely identifies the drive.

Model Number Self-Encrypting Drive (SED) FIPS 140-2 Level 2 certified

ST2000NM0011 No No

ST2000NM0031 Yes No

ST2000NM0051 Yes Yes

ST1000NM0011 No No

ST1000NM0031 Yes No

ST1000NM0051 Yes Yes

ST500NM0011 No No

ST500NM0031 Yes No

ST500NM0051 Yes Yes

Constellation ES.1 Serial ATA Product Manual, Rev. B 3

2.1 About the Serial ATA interface

The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary

advantages include:

• Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jump-

ers or other configuration options.

• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.

• Scalability to higher performance levels.

In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial

ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disc drive in your current

system and expect all of your existing applications to work as normal.

The Serial ATA interface connects each disc drive in a point-to-point configuration with the Serial ATA host

adapter. There is no master/slave relationship with Serial ATA devices like there is with parallel ATA. If two

drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they

were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0

(master) devices.

Note. The host adapter may, optionally, emulate a master/slave environment to host software where two

devices on separate Serial ATA ports are represented to host software as a Device 0 (master) and

Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a

master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA

environment.

The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide

backward compatibility with existing host systems and software. The Command and Control Block registers,

PIO and DMA data transfers, resets, and interrupts are all emulated.

The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device regis-

ters, referred to as the Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For addi-

tional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA: High Speed Serialized

AT Attachment” specification. The specification can be downloaded from www.serialata.org.

4 Constellation ES.1 Serial ATA Product Manual, Rev. B

3.0 Drive specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal

power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the

following drive models:

3.1 Specification summary tables

The specifications listed in the following tables are for quick reference. For details on specification measure-

ment or definition, see the appropriate section of this manual.

Table 1: Drive specifications summary

ST2000NM0011 ST2000NM0031 ST2000NM0051

ST1000NM0011 ST1000NM0031 ST1000NM0051

ST500NM0011 ST500NM0031 ST500NM0051

Drive specification ST2000NM0011

ST2000NM0031

ST2000NM0051

ST1000NM0011

ST1000NM0031

ST1000NM0051

ST500NM0011

ST500NM0031

ST500NM0051

Formatted (512 bytes/sector)* 2TB 1TB 500GB

Guaranteed sectors 3,907,029,168 1,953,525,168 976,773,168

Heads 8 4 2

Discs 4 2 1

Bytes per sector 512

Default sectors per track 63

Default read/write heads 16

Default cylinders 16,383

Recording density, KBPI (Kb/in max) 1523

Track density, KTPI (ktracks/in avg.) 237

Areal density, (Gb/in

2

avg) 324

Spindle speed (RPM) 7200

Internal data transfer rate

(Mb/s max)

1300

Sustained data transfer rate OD

(MB/s max)

147

I/O data-transfer rate

(MB/s max)

600

ATA data-transfer modes supported PIO modes 0–4

Multiword DMA modes 0–2

Ultra DMA modes 0–6

Cache buffer 64MB

Weight: (maximum) 710g (1.565 lb) 640g (1.411 lb) 610g (1.345 lb)

Constellation ES.1 Serial ATA Product Manual, Rev. B 5

*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

Average latency 4.16ms

Power-on to ready (sec max) 15 10 7

Standby to ready (sec max) 15 10 7

Track-to-track seek time (ms typical) 0.5 read

0.8 write

Average seek, read (ms typical) <8.5

Average seek, write (ms typical) <9.5

Startup current (typical) 12V (peak) 2.8A

2.0A (optional configuration through Smart Command Transport)

Voltage tolerance (including noise) 5V ± 5%

12V ± 10%

Ambient temperature 5° to 60°C (operating/tested)

–40° to 70°C (nonoperating)

Temperature gradient

(°C per hour max)

20°C (operating)

30°C (nonoperating)

Relative humidity 5% to 90% (operating)

5% to 95% (nonoperating)

Relative humidity gradient 30% per hour max

Altitude, operating –60.96 m to 3,048 m

(–200 ft to 10,000+ ft)

Altitude, nonoperating

(below mean sea level, max)

–60.96 m to 12,192 m

(–200 ft to 40,000+ ft)

Operational Shock (max at 2 ms) Read 70 Gs / Write 40 Gs

Non-Operational Shock (max at 2 ms) 300 Gs 350 Gs

Vibration, operating 5–22 Hz: 0.25 Gs, Limited displacement

22–350 Hz: 0.50 Gs

350–500 Hz: 0.25 Gs

Operation Rotational vibration 20–1500Hz: 12.5 rads/s²

Vibration, nonoperating 10–500 Hz: 4.9 Grms ref

Drive acoustics, sound power (bels)

Idle** 2.7 (typical)

2.9 (max)

2.2 (typical)

2.5 (max)

1.9 (typical)

2.3 (max)

Performance seek 3.0 (typical)

3.3 (max)

2.8 (typical)

3.1 (max)

2.7 (typical)

3.0 (max)

Nonrecoverable read errors 1 sector per 10

15

bits read

Annualized Failure Rate (AFR) 0.73% based on 8760 POH

Warranty To determine the warranty for a specific drive, use a web browser to access the following

web page:

support.seagate.com/customer/warranty_validation.jsp

You will be asked to provide the drive serial number, model number (or part number) and

country of purchase. After submitting this information, the system will display the warranty

information for your drive.

Load-unload cycles 300,000 (25°C, 50% rel. humidity) (600,000 design life testing)

Supports Hotplug operation per

Serial ATA Revision 2.6 specification

Yes

Drive specification ST2000NM0011

ST2000NM0031

ST2000NM0051

ST1000NM0011

ST1000NM0031

ST1000NM0051

ST500NM0011

ST500NM0031

ST500NM0051

6 Constellation ES.1 Serial ATA Product Manual, Rev. B

3.2 Formatted capacity

Model

Formatted

capacity*

Guaranteed

sectors

Bytes per sector

ST2000NM0011

ST2000NM0031

ST2000NM0051

2TB 3,907,029,168

512

ST1000NM0011

ST1000NM0031

ST1000NM0051

1TB 1,953,525,168

ST500NM0011

ST500NM0031

ST500NM0051

500GB 976,773,168

*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

3.2.1 LBA mode

When addressing these drives in LBA mode, all blocks (

sectors) are consecutively numbered from 0 to n–1,

where n is the number of guaranteed sectors as defined above.

See Section 7.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-

bit addressing support of drives with capacities over 137GB.

3.3 Default logical geometry

Cylinders Read/write heads Sectors per track

16,383 16 63

LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,

where n is the number of guaranteed sectors as defined above.

3.4 Recording and interface technology

Interface Serial ATA (SATA)

Recording method Perpendicular

Recording density, KBPI (Kb/in max) 1523

Track density, KTPI (ktracks/in avg) 237

Areal density (Gb/in

2

avg) 324

Spindle speed (RPM) (± 0.2%) 7200

Internal data transfer rate (Mb/s max) 1300

Sustained data transfer rate (MB/s max) 147

I/O data-transfer rate (MB/s max) 600 (Ultra DMA mode 5)

Constellation ES.1 Serial ATA Product Manual, Rev. B 7

3.5 Physical characteristics

Weight: (maximum)

2TB models 710g (1.565 lb)

1TB models 640g (1.411 lb)

500GB models 610g (1.345 lb)

Cache buffer 64MB (64,768KB)

3.6 Seek time

Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using

drive diagnostics. The specifications in the table below are defined as follows:

• Track-to-track seek time is an average of all

possible single-track seeks in both directions.

• Average seek time is a true statistical random aver

age of at least 5000 measurements of seeks between

random tracks, less overhead.

*Typical seek times (ms) Read Write

Track-to-track 0.5 0.8

Average <8.5 <9.5

Average latency: 4.16

*Measured in performance mode.

Note. Th

ese drives are designed to consistently meet the seek times represented in this manual. Physical

seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted

values. However, due to the manner in which these drives are formatted, benchmark tests that

include command overhead or measure logical seeks may produce results that vary from these

specifications.

3.7 Start/stop times

2TB models 1TB models 500GB models

Power-on to Ready (sec) 15 (max) 10 (max) 7 (max)

Standby to Ready (sec) 15 (max) 10 (max) 7 (max)

Ready to spindle stop (sec) 20 (max)

8 Constellation ES.1 Serial ATA Product Manual, Rev. B

3.8 Power specifications

The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 4 on page 27.

3.8.1 Power consumption

Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on

an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient

temperature.

• Spinup power

Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating

speed.

• Seek mode

During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and

does not execute a read or write operation. Servo electronics are active. Seek mode power represents the

worst-case power consumption, using only random seeks with read or write latency time. This mode is not

typical and is provided for worst-case information.

• Read/write power and current

Read/write power is measured with the heads on track, based on a 16-sector write followed by a 32-ms

delay, then a 16-sector read followed by a 32ms delay.

• Operating power and current

Operating power is measured using 40 percent random seeks, 40 percent read/write mode (1 write for each

10 reads) and 20 percent drive idle mode.

• Idle mode power

Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in

a random track location.

• Standby mode

During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/

write electronics are in power-down mode.

Constellation ES.1 Serial ATA Product Manual, Rev. B 9

Table 2: 2TB Drive DC power requirements

3.0Gb mode 6.0Gb mode

Voltage +5V +12V +5V +12V

Regulation ±5% ±5% ±5% ±5%

Avg Idle Current * 0.24 0.41 0.24 0.42

Advanced Idle Current *

Idle_A 0.24 0.41 0.24 0.42

Idle_B 0.14 0.36 0.15 0.37

Idle_C 0.14 0.20 0.15 0.20

Standby 0.13 0.02 0.14 0.02

Transition Current *

Idle_A (Active) 0.54 1.76 0.54 1.72

Idle_B (Active) 0.60 1.61 0.62 1.57

Idle_C (Active) 0.62 2.39 0.64 2.37

Standby (Active) 0.68 2.72 0.66 2.73

Average Sleep Current 0.13 0.02 0.14 0.02

Maximum Start Current

DC (peak DC) 3σ 0.53 2.10 0.53 2.10

AC (Peak DC) 3σ 0.69 2.78 0.90 2.77

Delayed Motor Start (DC max)

3σ

0.14 0.02 0.14 0.02

Peak operating current (random read):

Typical DC 0.29 0.61 0.30 0.62

Maximum DC 3σ 0.30 0.63 0.31 0.65

Maximum DC(peak) 3σ 1.09 1.65 1.10 1.64

Peak operating current (random write)

Typical DC 0.39 0.53 0.39 0.53

Maximum DC 3σ 0.40 0.54 0.40 0.54

Maximum DC(peak) 3σ 1.16 1.66 1.127 1.65

Peak operating current (sequential read)

Typical DC 0.62 0.42 0.62 0.43

Maximum DC 3σ 0.64 0.44 0.64 0.44

Maximum DC(peak) 3σ 0.94 0.64 0.96 0.66

Peak operating current (sequential write)

Typical DC 0.78 0.42 0.78 0.43

Maximum DC 3σ 0.83 0.44 0.82 0.44

Maximum DC(peak) 3σ 1.18 0.67 1.24 0.642

10 Constellation ES.1 Serial ATA Product Manual, Rev. B

Table 3: 1TB Drive DC power requirements

3.0Gb mode 6.0Gb mode

Voltage +5V +12V +5V +12V

Regulation ±5% ±5% ±5% ±5%

Avg Idle Current * 0.23 0.28 0.24 0.28

Advanced Idle Current *

Idle_A 0.23 0.28 0.24 0.28

Idle_B 0.14 0.25 0.15 0.25

Idle_C 0.14 0.14 0.15 0.14

Standby 0.13 0.01 0.14 0.02

Transition Current *

Idle_A (Active) 0.54 1.46 0.60 1.46

Idle_B (Active) 0.62 1.35 0.60 1.31

Idle_C (Active) 0.62 2.03 0.60 2.05

Standby (Active) 0.66 2.49 0.84 2.51

Average Sleep Current 0.13 0.02 0.14 0.01

Maximum Start Current

DC (peak DC) 3σ 0.99 1.92 0.49 1.90

AC (Peak DC) 3σ 0.76 2.50 0.78 2.59

Delayed Motor Start (DC max)

3σ

0.14 0.02 0.15 0.02

Peak operating current (random read):

Typical DC 0.29 0.46 0.30 0.48

Maximum DC 3σ 0.30 0.56 0.31 0.58

Maximum DC(peak) 3σ 1.12 1.52 1.14 1.55

Peak operating current (random write)

Typical DC 0.39 0.36 0.40 0.37

Maximum DC 3σ 0.40 0.41 0.41 0.41

Maximum DC(peak) 3σ 1.13 1.55 1.14 1.56

Peak operating current (sequential read)

Typical DC 0.61 0.28 0.62 0.27

Maximum DC 3σ 0.63 0.29 0.63 0.29

Maximum DC(peak) 3σ 0.91 0.46 0.99 0.55

Peak operating current (sequential write)

Typical DC 0.79 0.28 0.79 0.28

Maximum DC 3σ 0.82 0.29 0.81 0.29

Maximum DC(peak) 3σ 1.09 0.51 1.12 0.57

Constellation ES.1 Serial ATA Product Manual, Rev. B 11

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

Table 4: 500GB Drive DC power requirements

3.0Gb mode 6.0Gb mode

Voltage +5V +12V +5V +12V

Regulation ±5% ±5% ±5% ±5%

Avg Idle Current * 0.37 0.21 0.38 0.21

Advanced Idle Current *

Idle_A 0.37 0.21 0.38 0.21

Idle_B 0.14 0.19 0.15 0.19

Idle_C 0.14 0.12 0.15 0.12

Standby 0.13 0.01 0.14 0.02

Transition Current *

Idle_A (Active) 0.78 1.48 0.78 1.42

Idle_B (Active) 0.72 1.19 0.72 1.35

Idle_C (Active) 0.72 2.01 0.72 2.03

Standby (Active) 0.72 2.49 0.72 2.43

Average Sleep Current 0.13 0.01 0.14 0.02

Maximum Start Current

DC (peak DC) 3σ 0.62 1.87 0.62 1.88

AC (Peak DC) 3σ 0.76 2.56 0.80 2.65

Delayed Motor Start (DC max)

3σ

0.14 0.02 0.15 0.02

Peak operating current (random read):

Typical DC 0.32 0.40 0.32 0.40

Maximum DC 3σ 0.32 0.48 0.32 0.47

Maximum DC(peak) 3σ 1.03 1.48 01.06 1.450

Peak operating current (random write)

Typical DC 0.40 0.30 0.41 0.30

Maximum DC 3σ 0.41 0.33 0.42 0.33

Maximum DC(peak) 3σ 1.16 1.44 1.16 1.44

Peak operating current (sequential read)

Typical DC 0.61 0.20 0.62 0.20

Maximum DC 3σ 0.63 0.22 0.64 0.22

Maximum DC(peak) 3σ 0.91 0.43 0.97 0.45

Peak operating current (sequential write)

Typical DC 0.79 0.20 0.79 0.20

Maximum DC 3σ 0.83 0.22 0.84 0.22

Maximum DC(peak) 3σ 1.15 0.40 1.15 0.44

12 Constellation ES.1 Serial ATA Product Manual, Rev. B

3.8.1.1 Typical current profiles

2TB model current profile

Figure 1. Typical 2TB model 5V & 12V startup and operation current profile

Constellation ES.1 Serial ATA Product Manual, Rev. B 13

1TB model current profile

Figure 2. Typical 1TB model 5V & 12V startup and operation current profiles

14 Constellation ES.1 Serial ATA Product Manual, Rev. B

500GB model current profile

Typical 500GB model 5V & 12V startup and operation current profiles

3.8.2 Conducted noise

Input noise ripple is measured at the host system power

supply across an equivalent 80-ohm resistive load on

the +12 V line or an equivalent 15-ohm resistive load on the +5V line.

• Using 12V power, the drive is expected to operate with

a maximum of 120mV peak-to-peak square-wave

injected noise at up to 10MHz.

• Using 5V power, the drive is expected to operate with a maximum of 1

00mV peak-to-peak square-wave

injected noise at up to 10MHz.

Note. Equ

ivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write

current.

3.8.3 Voltage tolerance

Voltage tolerance (including noise):

5V

± 5%

12V ±10%

Page is loading ...

Seagate 1TB SATA, 7200rpm User manual

Related papers

Other documents