Kenmore Elite 79575556400 Installation guide

Brand: Kenmore Elite

Model: 79575556400

Category: Fridges

Type: Installation guide

This manual is also suitable for

Ar'rENTION IN

LLER:

FOR A QUALITY INSTALLATION,

FOLLOW THESE INSTRUCTIONS.

[_ LIFT UNIT OFF SHIPPING

BASE (Requires 2 people)

Lift

• Using the handles at the back top

of the cabinet, and supporting the

refrigerator at the bottom front,

lift the unit off the shipping base.

• Use padded hand truck to protect

_,efrigerator finish.

r -%

---_ TRUCKING REFRIGERATOR

• LEAVE TAPE AND ALL PACKAGING

ON DOORS until refrigerator is in its

final location.

• TRUCK FROM SIDE ONLY.

• Avoid overtightening strap to prevent

damaging doors. ,,_

_ EVEL UNIT AND INSTALL

BASE COVER

If the doors are misaligned, realign as

follows.

• Remove basecover by loosening

two screws.

• Turnthe leveling screw clockwiseto

raise that side of the refrigeratoror

counterclockwise to lower it.

• When doors arealigned, they will

close smoothly.

• Replace base cover.

For 21 cu. ft., if entrance is less than 31" wide, remove doors.

For 25 cu. ft., if entrance is less than 35" wide, remove doors.

For detailed instructions, see the Owner's Manual.

TOP HINGE

.=Cover

Door Switch

Wire /

,Wire \

Hing_ Harness _

Hinc

Lever Latch

Wire

Ground screw Top hinge Harness

Hinge Cover

/ %-'_-_-"-_.j Hinge

>_ Latch

TO REMOVE DOORS

NOTE: Before you begin, turn the refrigerator OFF and unplug it.

MIDDLE HINGE

4 mm philips

head screw

_ jHinge Pin

:// 10 mm

Hex Head

Bolts

1. Open door. Loosen top hinge cover screw. With flat tip screwdriver, pry back hooks on cover underside.

Lift up cover.

2. Disconnect door switch wire harness and remove cover.

3. Left door: Disconnect water supply tube by pushing back on the disconnect ring and pulling tube out.

4. Disconnect the wire harnesses (left door: three; right door: one) and remove the grounding screw.

5. Rotate hinge lever (left door: counterclockwise; right door: clockwise) and remove.

CAUTION: When lifting hinge free of latch, be careful that door does not fall forward.

6. Lift door up from middle hinge pin and remove door.

7. Place door, inside facing up, down onto a non-scratching surface.

8. Replace door(s) in opposite manner and order of removal.

TO REMOVE DRAWER

1. Pullthe drawerout to

full extension and remove

basket bylifting up.

TO REPLACE DRAWER

1. Pull both rails out to

full extension.

2. Remove screw (1) on

each side of rail

system.

2. Hook door supports

into rail tabs, as

illustrated (2), and

lower door into

final position.

Andtighten

the screw (1).

3. Lift top ofdoor to unhook

door supportsfrom rail

system. Lift door out to

remove.

3. With the drawer pulled

out to full extension,

insert the lower basket

in the railassembly.

[] CAUTION : When you remove the drawer, do not hold handle. Ifit comes off, it could cause personal injury.

[] CAUTION : When laying down the drawer, becareful not to damage the floor or hurtyour feet by the sharp edges on

hinge side. J

APPLIANCE POLISH WAX

IS RECOMMENDED FOR

REMOVING TAPE RESIDUE

AND HAND PRINTS FROM

REFRIGERATOR EXTERIOR.

REMOVE ALL TAPE AND

OTHER PACKAGING

MATERIAL FROM

REFRIGERATOR INTERIOR.

DO NOT REMOVE SERIAL

PLATE.

PLUG IN AND SET CONTROLS

• Plug in the refrigerator.

• For best performance, set the refrigerator control to 37°F (3°C) and the freezer

control to 0°F (-18°C).

• Allow 24 hours for the temperatures to stabilize.

• If an icemaker has been installed, set the icemaker power switch to I (on)AFTER

the house water line is connected.

PLACE SHELVES AND

PANS IN PROPER USAGE

POSITIONS.

P F" o?EO

KESURE PROPER

II/I GROUNDEXISTS

BEFORE USE

TEMPORARY METHOD _

(Adapter plugs not I _(1

permitted in Canad:, _ ._:! I

IV !! _- _ ENSURE PROPER

_ GROUND AND

_/// FIRM CONNECTION

BEFORE USE

IMPORTANT: PLEASE READ CAREFULLY

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.

The power cord of this appliance isequipped with a three-prong (grounding) plug that mates with a standard three-prong (grounding) wall receptacle to minimize the

risk of electric shock hazard from this appliance. The customer should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle

is properly grounded.

Where a standard two-prong wall receptacle is encountered, it is the personal responsibility and obligation of the customer to have it replaced with a properly grounded

three-prong wall receptacle.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD.

USAGE SITUATIONS WHERE THE APPLIANCE'S POWER CORD WILL BE DISCONNECTED INFREQUENTLY

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug. However, if you still elect to use an adapter,

where local codes permit, a TEMPORARY CONNECTION may be made to a properly grounded two-prong wall receptacle by the use of a UL listed adapter which is

available at most hardware stores. The larger slot of the adapter must be aligned to provide proper polarity in the connection of the power cord.

CAUTION: Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance unless the cover screw is metal, and not insulated,

and the wall receptacle is grounded through the house wiring. The customer should have the circuit checked by a qualified electrician to make sure the receptacle is

properly grounded. When disconnecting the power cord from the adapter, always hold the adapter with one hand. If this is not done, the adapter ground terminal is very

likely to break with repeated use. Should this happen, DO NOT USE the appliance until a proper ground has again been established.

USAGE SITUATIONS WHERE THE APPLIANCE'S POWER CORD WILL BE DISCONNECTED FREQUENTLY

Do not use an adapter plug in these situations because frequent disconnecting of the power cord places undue strain on the adapter and leads to eventual failure of the

adapter ground terminal. The customer should have the two-prong wall receptacle replaced with a three-prong (grounding) receptacle by a qualified electrician before

using the appliance.

3840JL2019A

Page is loading ...