Eaton ESWB23 User guide

Category
Power distribution units (PDUs)
Type
User guide
Eaton
®
Advanced Enclosure Power Distribution Unit (ePDU
®
)
User’s Guide
Eaton and ePDU are registered trademarks of Eaton Corporation or its subsidiaries and affiliates. Google
Chrome is a trademark of Google, Inc. HyperTerminal is a registered trademark of Hilgraeve. Linux is a
registered trademark of Linus Torvalds in the United States, other countries, or both. Microsoft, Internet
Explorer, Vista, and Windows are registered trademarks of Microsoft Corporation in the United States and
other countries. Mozilla and Firefox are registered trademarks of the Mozilla Foundation. National Electrical
Code and NEC are registered trademarks of National Fire Protection Association, Inc. Phillips is a registered
trademark of Phillips Screw Company. Torx is a registered trademark of Acument Intellectual Properties, Llc.
All other trademarks are property of their respective companies.
©Copyright 2011–2012 Eaton Corporation, Raleigh NC, USA. All rights reserved. No part of this document may
be reproduced in any way without the express written approval of
Eaton Corporation.
Class A EMC Statements
FCC Information
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
ICES-003
This Class A Interference Causing Equipment meets all requirements of the Canadian Interference Causing
Equipment Regulations ICES-003.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du
Canada.
Eaton is not responsible for damage to this product resulting from accident, disaster, misuse, abuse, non-Eaton
modification of the product, or other events outside the reasonable control of Eaton or not arising under normal
operating conditions.
CUS
1F61
I.T.E.
Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important information:
RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk
of electric shock symbol.
CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's
manual for additional information, such as important operating and
maintenance instructions.
This symbol indicates that you should not discard waste electrical or
electronic equipment (WEEE) in the trash. For proper disposal, contact your
local recycling/reuse or hazardous waste center.
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU i
Table of Contents
1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Eaton ePDU Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Environmental Monitoring Probe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Cord Retention Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Ease of Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Power Control Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Configurability and Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Inspecting the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installing the Optional Cord Retention Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Installing the ePDU in a Rack Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using Cage Nuts with Mounting Clip Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using Keyholes with Mounting Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Using Keyholes with Mounting Buttons and Clip Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Grounding the ePDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Hardware Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Connecting to a Computer Serial Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Connecting to a LAN Ethernet Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installing an Optional EMP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Connecting the Output Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Equipment Setup Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4 NETWORK COMMUNICATION CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Enable the Network Management Card in Operation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
IP Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Obtaining the IPv4 Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Retrieve the IPv4 Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Using the IPv4 Default Address Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Obtaining the IPv6 Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Networks That Allow Auto-Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Networks That Do Not Allow IPv6 Auto-Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Retrieve the IPv6 Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Verify Network Management Card Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table of Contents
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU ii
5 OPERATION OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Three-Phase Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Environmental Protection and Pin Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Outlet Groups Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Menu and Status Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
LCD Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Operation Mode DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Restarting the Network Management Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Hardware Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Software Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
LED Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Serial and Ethernet Connection Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Remote Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Operation Concepts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
User Login and Access Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Power Schedules for Managed and Switched ePDUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Group Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Common Operation Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Download/Upload the Network Management Card File Configuration . . . . . . . . . . . . . . . . . . . 53
Download/Upload the ePDU File Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Clear ePDU and Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Refresh the Data Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
SNMP Agent Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Actions on Individual Outlets and Groups of Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Restart the Network Management Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Restore the Default Factory Settings of the Network Management Card . . . . . . . . . . . . . . . . 56
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Modify Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Network Management Card Settings Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
ePDU Settings Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Starting the ePDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Shutting Down the ePDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
6 LCD OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
LCD Panel and Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Operation Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Screensaver Cycling Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Locked Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Lock 1 and Lock 2 Passwords. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Startup Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Main Menu Selections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Active Alarms Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Event Log Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Outlet Readings Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
ePDU Info Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Table of Contents
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU iii
7 WEB INTERFACE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Navigating the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Accessing the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Menu Selections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Logs & Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
ePDU Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Review/Modify ePDU Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Configure Environment Sensor Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
ePDU Groups. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Review/Modify ePDU Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
ePDU Outlets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Review/Modify ePDU Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Power Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Define a Power Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Active Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Review Active Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Clear the Event Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Download the Event Log as a Comma Separated Value File . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Email Notification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Configure the Email Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Trap Notification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Define the Trap Receivers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Group Definition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Configure an Outlet Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Access Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Configure the Superuser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Configure Multi-Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Enable/Disable SSL Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Enable/Disable the Telnet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Configure the Ethernet Link Speed and Duplex Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Configure the IPv4 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Configure the IPv6 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Enable/Disable Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Network Management Card Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Network Management Card Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
ePDU Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Enable/Disable the SNMP Agent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Define SNMPv1 Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Define SNMPv3 User-based Security Model Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
SNMP & DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Configure the DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Configure the SMTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Table of Contents
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU iv
Date &Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Manually Configure the Date and Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Automatically Configure the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
8 SERIAL INTERFACE OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Navigating the Serial Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Connecting the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Accessing the Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Selecting a Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Network Management Card Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Network Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
IPv4 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
IPv6 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Communication Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Hostname . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Primary and Secondary DNS IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Trap Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
SNMP v1 Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
SNMP V3 USM Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Modify a Table Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Restore Factory Defaults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Manually Configure the Date and Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Configure the Date and Time Automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Email Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Configure Email Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
Configure the Email Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Test Email . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Superuser Name and Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Multi-Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
EnergyWise Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
9 MAINTENANCE AND TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Equipment Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Network Management Card Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Enable Firmware Upgrade Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
DIP Switch Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Upload New Firmware Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Restart the Network Management Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Acknowledging the Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
Types of Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Alarms, Notices, and Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Table of Contents
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU v
10 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Model List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Weights and Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Electrical Input and Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Electrical Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Overcurrent Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Environmental and Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
11 SERVICE AND SUPPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Ordering Optional and Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU 1
Chapter 1 Introduction
Description
The Eaton
®
Advanced Enclosure Power Distribution Unit (ePDU
®)
is an intelligent ePDU that is designed to
distribute power within a standard 19" rack. A wide range of models let you connect and manage
C13 and C19
outlets from a single power connection with monitoring or switching capabilities, or both.
The monitoring or switching capabilities are characterized as follows:
l
Advanced Monitored (AM) with individual outlet monitoring but no outlet control
l
Switched (SW) with control of outlets but no individual outlet monitoring
l
Managed (MA) with control and monitoring at the outlet level
These capabilities are expressed in the model numbers of the ePDUs.
Eaton ePDU Models
There are 28 Eaton Advanced ePDU models. These models are categorized into eight model types defined
primarily by the input and outlet configurations. The
Advanced ePDU models support single-phase or
three-phase applications and can manage up to 24 outlets. All models feature an LCD window, LEDs to indicate
outlet status, and a set of communication connectors. The Advanced ePDUs have either attached or detached
input power cords and some models have circuit breakers.
Figure 1 shows an example of the Type 1 ePDU.
Figure 1. Type 1 Single-Phase Model (eSWA01 Switched Model Shown)
NOTE For details about individual model configurations, see Chapter 10, “Specifications”
on page 133.
eSWA01 (EU)
eAMA06 (EU)
eMAA10 (EU)
Introduction
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU 2
Figure 2 shows an example of the Type 2 ePDU.
Figure 2. Type 2 Single-Phase Model with Detachable Power Cord (eSWA03 Switched Model Shown)
Figure 3 shows an example of the Type 3 ePDU.
Figure 3. Type 3 Three-Phase Model (eSWA05 Switched Model Shown)
eSWA03 (EU - C19/C20)
eAMA07 (EU - IEC 60309 16A/C19)
eAMA08 (EU - C19/C20)
eMAA11 (EU - IEC 60309 16A/C19)
eMAA12 (EU - C19/C20)
eSWA02 (EU - IEC 60309 16A/C19)
eAM008 (US - C19/C20, L6-20P/C19)
eMA012 (US - C19/C20, L6-20P/C19)
eSWA05 (EU)
eMAA14 (EU)
eMA006 (US)
eAM002 (US)
Introduction
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU 3
Figure 4 shows an example of the Type 4 ePDU.
Figure 4. Type 4 Single-Phase Model (eMAA13 Managed Model Shown)
Figure 5 shows an example of the Type 5 ePDU.
Figure 5. Type 5 Single-Phase Model (eAM001 Advanced Monitored Model Shown)
eMAA13 (EU)
eSWA04 (EU)
eAMA09 (EU)
eAM001 (US)
eMA010 (US)
Introduction
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU 4
Figure 6 shows an example of the Type 6 ePDU.
Figure 6. Type 6 Three-Phase Model (eMA007 Managed Model Shown)
Figure 7 shows an example of the Type 7 ePDU.
Figure 7. Type 7 Three-Phase Model (eMA013 Managed Model Shown)
eMA007 (US)
eAM003 (US)
eAM004 (US)
eMA011 (US)
eMA013 (US)
Introduction
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU 5
Figure 8 shows an example of the Type 8 ePDU.
Figure 8. Type 8 Three-Phase Model (eAM005 Advanced Monitored Model Shown)
Accessories
The following accessories are optional and must be purchased separately.
Environmental Monitoring Probe
The optional Environmental Monitoring Probe (EMP) provides monitoring of external temperature, humidity,
and the status of two contact devices, providing greater power management control and flexible monitoring.
The EMP has the following features:
l
Simplified installation lets you install the EMP safely without turning off power to the ePDU or to the devices
that are connected to it.
l
The EMP monitors temperature and humidity information of any environment, protecting your critical
equipment. The EMP measures temperatures between 0
°C and 80°C (32°F and 176°F) with an accuracy
of
±1°C. The EMP measures relative humidity between 10% and 90% with an accuracy of ±5%.
l
The EMP can be located away from the ePDU with a Category 5 network cable up to 20m (65.6 ft) long.
l
The EMP monitors the status of two user-supplied contact devices.
l
Temperature, humidity, and contact closure status can be displayed through a variety of interfaces.
l
User-selectable alarm thresholds let you define acceptable temperature or humidity limits.
l
You can use e-mail client software to set up e-mail notification through Simple Mail Transfer Protocol (SMTP)
when acceptable alarm limits are exceeded or contact status changes.
l
Changes in external contact status are logged in the ePDU event history log.
l
When temperature and humidity values exceed user-selectable limits, the event is logged in the ePDU event
history log.
eAM005 (US)
eMA009 (US)
eMA014 (US)
Introduction
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU 6
Cord Retention Bracket
The Cord Retention Bracket kit includes brackets, cable ties, and mounting hardware. Attach the brackets to
your
ePDU to help you manage and secure the power cords of the devices you connect to the ePDU.
Features
The Eaton Advanced ePDU provides outstanding performance and reliability, including the following unique
benefits:
Ease of Use
l
Easy and flexible rack installation
l
Easy-to-use interface to display input and output status
l
Color-coded outlets and circuit breakers for easy correlation
l
A visual alarm (blinking LED) to indicate outlet current overload
l
User-friendly firmware updates
Communication
l
Comprehensive power management and flexible configuration through a Web browser or a serial
connection, a Telnet connection, Simple Network Management Protocol (SNMP), or a console emulator
such as HyperTerminal
®
l
Compatibility with network management tools such as Intelligent Power Manager (IPM), facilitated by
SNMP protocol
Power Control Management
l
Control of outlets for Switched or Managed ePDUs, both collectively and individually
l
The ability to power on, power off, and reboot the devices connected to each outlet
l
Fully shrouded local branch circuit breakers on products rated over 16A (Europe) / 20A (US) to protect
connected equipment against overload and short circuits
l
Configuring and monitoring the power schedule of outlets
l
Configuring collocated users as a user group with restricted access to user-defined outlet groups
Monitoring
l
Monitoring of the following at the outlet level:
- Root Mean Square (RMS) current
- Power factor
- Maximum and minimum thresholds for current or voltage
- RMS voltage
- Active power
- Apparent power
NOTE For information updates, refer to the Eaton ePDU catalog or go to
www.eaton.com/ePDU.
Introduction
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU 7
l
Monitoring of internal CPU temperature
l
Monitoring of the ePDU locally or remotely through a console or network
l
Remote monitoring of connected devices and sensors
l
Daily history report through e-mail
l
Detailed data-logging for statistical analysis and diagnostics
l
Dual color LCD for higher visibility on local alarms
Configurability and Security
l
Configurable alarm thresholds
l
Configurable user access control through collocation
l
Address-specific IP security mask to prevent unauthorized access
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU 8
Chapter 2 Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS — SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and
operation of the Eaton Advanced Enclosure Power Distribution Unit (ePDU). Please read all
instructions before operating the equipment and save this manual for future reference.
DANGER
This ePDU contains LETHAL VOLTAGES. All repairs and service should be performed by AUTHORIZED
SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS inside the ePDU.
SYSTEMS SHOULD ONLY BE INSTALLED, TESTED, AND CONFIGURED BY A COMPETENT PERSON.
IT IS ESSENTIAL THAT THIS EQUIPMENT IS CONNECTED TO AN ELECTRICAL SUPPLY THAT HAS
PROTECTIVE GROUND CONDUCTOR.
CAUTION
l
To reduce the risk of fire or electric shock, install this ePDU in a temperature and humidity
controlled, indoor environment, free of conductive contaminants. Ambient temperature must
not exceed 50°C (122°F). Do not operate near water or excessive humidity (90% maximum).
l
Do not use a two-wire power cord in any product configuration.
l
Test AC outlets at your computer and monitor for proper polarity and grounding.
l
Use only with grounded outlets at both the computer and monitor. When using a backup UPS,
power the computer, monitor, and appliance off the supply.
l
The installation power outlet used for the power supply to this equipment must be installed near
the equipment and must be easily accessible.
l
When installing this product, it is essential that the distribution circuit supplying the product is
protected by a branch circuit protection device with a maximum rating to suit the product
maximum rating.
l
TO ISOLATE THIS EQUIPMENT, DISCONNECT THE POWER SUPPLY PLUG.
l
This power distribution unit is intended for providing power to equipment only. Secondary
(satellite) power strips shall not be connected to the outlets.
l
This product has been designed to conform to the latest safety requirements. In addition to
compliance with standards for general use, it has been factory configured for use in rack
mounting environments, aiding the installer to provide systems compliant with relevant
standards.
CAUTION
This product contains a lithium battery on the internal Network Management Card:
l
The battery is not user-replaceable. However, there is risk of explosion if battery is replaced by
an incorrect type.
l
The battery is not user-replaceable. However, ensure that used batteries are disposed of
according to the instructions. For more information, contact your local recycling/reuse or
hazardous waste center for proper disposal information.
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU 9
Chapter 3 Installation
All Eaton Advanced Enclosure Power Distribution Unit (ePDU) models are 0U products and are mounted
vertically inside standard rack structures. Use the information in this chapter to prepare, install, and connect the
ePDU and optional accessories.
Installation Precautions
Before you install or connect the ePDU in a rack cabinet, observe the following precautions:
l
Only a competent service person should install, test, or configure the ePDU and its optional accessories. It
is the installers responsibility to ensure that the selected product is installed to meet national and local
safety regulations.
l
Read and understand all warnings and cautions listed in Chapter 2, “Safety Warnings” on page 8.
l
Review the documentation that comes with your rack cabinet for safety and cabling information.
l
Verify that the room air temperature is below 50°C (122°F).
l
Take all necessary precautions to handle the weight of the devices.
l
Connect all power cords to properly wired and grounded electrical outlets.
l
Verify that the power outlet is near the equipment and is easily accessible so that the ePDU can be
disconnected quickly.
l
Do not overload the power outlet when you install multiple devices in the rack cabinet.
l
To reduce the risk of fire, connect only to a circuit provided with branch circuit overcurrent protection with an
ampere (A) rating in accordance with the National Electrical Code
®
(NEC
®
), ANSI/NFPA 70 or your local
electrical code, as listed in Table 26 on page 137.
l
Verify that all equipment is unplugged from ePDU outlets before carrying out any testing.
Inspecting the Equipment
If any equipment has been damaged during shipment, keep the shipping cartons and packing materials for the
carrier or place of purchase, and file a claim for shipping damage. If you discover damage after acceptance, file
a claim for concealed damage.
To file a claim for shipping damage or concealed damage: 1) File with the carrier within 15 days of receipt of
the equipment; 2)
Send a copy of the damage claim within 15 days to your service representative.
NOTE Removing the rack cabinet doors and side panels might make installation
easier. See the rack cabinet documentation for more information.
NOTE The illustrations in this document might differ slightly from your hardware.
Installation
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU 10
Installation Overview
The installation instructions describe how to install the ePDU vertically in a standard rack. You can choose one
of three installation methods. This manual also describes how to install optional accessories, connect the ePDU
to a communication network, become familiar with
ePDU operation, and care for the ePDU.
Tools Required
The following tools are needed to install the ePDU in a rack cabinet:
l
One flat-blade screwdriver
l
One Phillips
®
screwdriver
l
One 10 mm (11/32”) star wrench (Torx
®
)
l
One cage nut insertion tool or flat-blade screwdriver (for installing cage nuts in some rack cabinets)
Package Contents
Table 1 lists the parts that are included with Advanced ePDU models. Table 2 on page 12 lists the detachable
ePDU power cords included with some Advanced ePDU models. See Table 30 on page 139 for a list of Eaton
catalog part numbers for ordering optional and spare parts for the
ePDU.
NOTE 1 Power cords for the devices that you connect to the ePDU are not
included.
NOTE 2 Some parts may not be used, depending on your choice of installation
method.
Table 1. Parts Included with All Eaton Advanced ePDU Models
Quantity Description
1
Eaton Advanced ePDU Quick Start for Installation and Connectivity
(P-164000041)
NOTE Supplied in the shipping carton and also available at
www.eaton.com/
ePDU.
1
Eaton Advanced ePDU Quick Start for Network Communication
Management
(P-164000060)
NOTE Supplied in the shipping carton and also available at
www.eaton.com/
ePDU.
2 Plastic mounting clip feet *
Installation
Eaton Advanced ePDU User’s Guide P-164000042—Rev 2 www.eaton.com/ePDU 11
2 Anti-sliding safety screw *
2 Cage nut **
2 Screw for mounting clip feet and cage nut assembly **
2 Screw for keyhole mounting button ***
2 Hex nut for keyhole mounting button ***
2 Keyhole mounting button ***
Table 1. Parts Included with All Eaton Advanced ePDU Models (Continued)
Quantity Description
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148

Eaton ESWB23 User guide

Category
Power distribution units (PDUs)
Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI