Gigabyte GV-N275SO-18I User manual

Brand: Gigabyte

Model: GV-N275SO-18I

Category: Graphics cards

Type: User manual

This manual is also suitable for

GV-N275SO-18I/

GV-N26SO-896I

NVIDIA

GeForce

GTX 275/260 Graphics Accelerator

User's Manual

Rev. 101

12MM-N26S8I-101R

in any form without the expressed, written permission of GBT.

Trademarks

Third-party brands and names are the properties of their respective owners.

Notice

Please do not remove any labels on this graphics card. Doing so may void the warranty of this card.

Due to rapid change in technology, some of the specifications might be out of date before publication of this this manual.

The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author

make a commitment to update the information contained herein.

Macrovision corporation product notice:

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property

rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other

limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

in any form without the expressed, written permission of GBT.

Trademarks

Third-party brands and names are the properties of their respective owners.

Notice

Please do not remove any labels on this graphics card. Doing so may void the warranty of this card.

Due to rapid change in technology, some of the specifications might be out of date before publication of this this manual.

The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author

make a commitment to update the information contained herein.

Macrovision corporation product notice:

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property

rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other

limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

VGA Card

GV-N275SO-18I

Aug.28,2009

VGA Card

GV-N275SO-18I

VGA Card

GV-N26SO-896I

Aug.21,2009

VGA Card

GV-N26SO-896I

- 4 -

Table of Contents

1. Introduction ................................................................................................................ 5

1.1. Features ......................................................................................................................... 5

1.2. Minimum System Requirements .................................................................................... 5

2. Hardware Installation.................................................................................................. 6

2.1. Board Layout ................................................................................................................. 6

2.2. Hardware Installation.................................................................................................... 10

3. Software Installation.................................................................................................. 13

3.1. Driver and Utility Installation......................................................................................... 13

3.1.1. Driver Installation ......................................................................................................... 13

3.1.2. GIGABYTE Gamer HUD Lite on Driver Disk ........................................................... 15

3.2. Display Properties Pages ........................................................................................ 17

3.3. Accessing NVIDIA Control Panel............................................................................ 18

4. Troubleshooting Tips................................................................................................ 26

5. Appendix ................................................................................................................. 27

5.1. How to Reflash the BIOS in MS-DOS Mode.............................................................. 27

5.2. Resolutions and Color Depth Tables ............................................................................. 28

5.3. Regulatory Statements ................................................................................................. 30

- 5 - Introduction

1. Introduction

1.1. Features

• Powered by NVIDIA

GeForce

GTX 275/260 Graphics Processing Unit (GPU)

• Supports PCI Express 2.0

• Integrated with 1792 MB GDDR3 memory (For GV-N275SO-18I only)

• Integrated with 896 MB GDDR3 memory (For GV-N26SO-896I only)

• Supports DirectX 10

• Supports NVIDIA

SLI

(Scalable Link Interface) technology

(Note)

• Supports 1 HDMI connector

• Supports 1 D-Sub connector

• Support 1 DVI-I connectors

• Supports HDCP (High-Bandwidth Digital Content Protection) technology

1.2. Minimum System Requirements

• Hardware

- Intel

Pentium

/Core

2 or AMD Athlon

/Phenom

- 512 MB of system memory; 2 GB or more for best performance

- Optical drive for software installation (CD-ROM or DVD-ROM drive)

- A 550 Watt power supply or above is a must

• Operating System

- Windows

Vista

- Windows

XP with Service Pack 2 (SP2)

- Windows

XP Professional x64 Edition

• SLI

Configuration

If you are planning on using this graphics card as part of an SLI system, the following

are required:

- An SLI certified motherboard with two/three PCIe x16 slots and correct chipset driver

- Two GV-N275SO-18I/GV-N26SO-896I for SLI configuration;

Three GV-N275SO-18I/GV-N26SO-896I for 3-way SLI configuration

- A power supply with 900-watt or above is recommended

- An SLI bridge connector or 3-way SLI bridge connector

(Note) SLI technology requires a PCI Express motherboard with two x16 physical connectors. Graphics cards working in an

SLI configuration must be with the same model name (e.g. GV-N275SO-18I/GV-N26SO-896I) and from the same vendor

(e.g. GIGABYTE TECHNOLOGY).

- 6 -

Super Overclock Series Graphics Accelerator

2. Hardware Installation

2.1. Board Layout

DVI-I Connector

D-Sub monitor Connector

(15-pin)

HDMI Connector

SLI Connector

DVI-I

Connector

Analog LCD Monitor Analog Monitor

Digital LCD Monitor

DVI Output

D-Sub

Output

DVI-I to D-Sub

Adapter(optional)

HDMI TV

Analog LCD Monitor Analog Monitor

HDMI Connector

D-Sub monitor

Connector

(15-pin)

HDMI to DVI-I Adapter

(Optional)

Digital LCD Monitor

1. GV-N275SO-18I

- 7 - Hardware Installation

DVI-I Connector

D-Sub monitor Connector

(15-pin)

HDMI Connector

SLI Connector

DVI-I

Connector

Analog LCD Monitor Analog Monitor

Digital LCD Monitor

DVI Output

D-Sub

Output

DVI-I to D-Sub

Adapter(optional)

HDMI TV

Analog LCD Monitor Analog Monitor

HDMI Connector

D-Sub monitor

Connector

(15-pin)

HDMI to DVI-I Adapter

(Optional)

Digital LCD Monitor

2. GV-N26SO-896I

- 8 -

Super Overclock Series Graphics Accelerator

The GV-N275SO-18I/GV-N26SO-896I graphics card is a performance optimized high-end card. Power

is taken from the PCI Express host bus as well as the two 6-pin PCI Express power connectors.

If you want to use the included 6-pin power adapters, make sure at least 12V/15A current is

supplied to each 4-pin power connector on the adapters. Failure to do so may jeopardize the

stability of the graphics card.

Incorrect Connection

(The two 4-pin power connectors on

the adapter are connected to the same

system power supply cable.)

Correct Connection

(The two 4-pin power connectors on the

adapter are connected to two independent

system power supply cables.)

Requires at least 12V current

rating of 15A

6-pin Power

Adapter

Requires at least 12V current

rating of 15A

- 9 - Hardware Installation

Expansion cards contain very delicate Integrated Circuit (IC) chips. To

protect them against damage from static electricity, you should follow some

precautions whenever you work on your computer.

1. Turn off your computer and unplug power supply.

2. Use a grounded wrist strap before handling computer components. If you do not

have one, touch both of your hands to a safely grounded object or to a metal object,

such as the power supply case.

3. Place components on a grounded antistatic pad or on the bag that came with the

components whenever the components are separated from the system.

The card contains sensitive electric components, which can be easily damaged by static

electricity, so the card should be left in its original packing until it is installed.

Unpacking and installation should be done on a grounded anti-static mat. The operator

should be wearing an anti-static wristband, grounded at the same point as the anti-static

mat.

Inspect the card carton for obvious damage. Shipping and handling may cause damage

to your card. Be sure there are no shipping and handling damages on the card before

proceeding.

DO NOT APPLY POWER TO YOUR SYSTEM IF THE GRAPHICS CARD IS

DAMAGED.

In order to ensure that your graphics card can work correctly, please use

official GIGABYTE BIOS only. Using non-official GIGABYTE BIOS might

cause problem(s) on the graphics card.

- 10 -

Super Overclock Series Graphics Accelerator

2.2. Hardware Installation

Now that you have prepared your computer, you are ready to install your graphics card.

Step 1.

Locate the PCI Express x16 slot. If necessary, remove the

metal cover from this slot; then align your graphics card with

the PCI Express x16 slot, and press it in firmly until the card is

fully seated.

Step 2.

Replace the screw to fasten the card in place, and replace the

computer cover.

Make sure that the gold edge connector of the graphics card is securely

inserted.

Step 3.

Plug the display cable into your card; then turn on the computer

and monitor. To connect a D-Sub monitor to your graphics card,

use the D-Sub connector. To connect a flat panel display to your

graphics card, use the DVI-I connector. To connect an HDMI

monitor to your graphics card, use the HDMI connector.

Connect a flat panel display

Connect a D-Sub monitor

Connect an HDMI monitor

To Flat Panel DisplayTo D-Sub MonitorTo HDMI Monitor

After installation, remember to connect the power cable to your graphics card, or the system

will not boot (refer to page 8 to see the details). Do not touch the card when it's operating to

prevent system instability.

- 11 - Hardware Installation

You are now ready to proceed with the installation of the graphics card driver. Please refer to next

chapter for detailed instructions.

Step 4.

To connect an HDMI TV, follow the steps below to enable the S/PDIF in function for the graphics card.

Connect the provided S/PDIF cable to the graphics

card.

Connect the S/PDIF cable to the motherboard.

(the red wire connects to the S/PDIF out pin and

the black to the Ground pin)

- 12 -

Super Overclock Series Graphics Accelerator

How NVIDIA

SLI

(Scalable Link Interface) technology works:

In an SLI configuration, two/three SLI-ready graphics cards of the same model and the same manufac-

turers are connected together via SLI bridge connector in a system that provides two/three x16 PCI

Express slots to scale graphics performance. The picture below shows that two and three graphics

cards are linked in parallel in an SLI configuration.

SLI bridge connector

(provided by motherboard manufacturer)

Two SLI-ready graphics

cards of the same type.

(Example:

GV-N28-1GH-B)

3-Way SLI bridge connector

(provided by motherboard manufacturer)

Three SLI-ready graphics

cards of the same type.

(Example:

GV-N28-1GH-B)

SLI Configuration:

3-Way SLI Configuration:

- 13 - Software Installation

3. Software Installation

Notice the following guidelines before installing the drivers:

1. First make sure your system has installed DirectX 9 or later version.

2. Make sure your system has installed the appropriate motherboard drivers (for the motherboard

drivers, please contact the motherboard manufacturer.)

3.1. Driver and Utility Installation

3.1.1. Driver Installation

After installing the operating system, insert the driver disk into your optical drive. The driver Autorun

screen is automatically displayed which looks like that shown in the screen shot below. (If the driver

Autorun screen does not appear automatically, go to My Computer, double-click the optical drive and

execute the setup.exe program.)

For software MPEG support in Windows XP, you must install DirectX first. Users who run

Windows XP with Service Pack 2 or above do not need to install DirectX separately.

Step 1:

Click the Install Display Driver item.

Step 2:

Click the Next button.

- 14 -

Super Overclock Series Graphics Accelerator

The system is installing the components.

Step 4:

Click the Finish button to restart the computer.

Then the driver installation is completed.

Step 3:

Click the Yes button.

- 15 - Software Installation

3.1.2. GIGABYTE Gamer HUD Lite on Driver Disk

Step 1:

Click the GIGABYTE Gamer HUD Lite item.

Step 2:

Choose the language for the installation and click the OK button.

Step 3:

Click the Next button.

Step 4:

Click the Install button.

The system is installing the components. Step 5:

Click the Finish button. Then the installation of

the GIGABYTE Gamer HUD Lite is completed.

- 16 -

Super Overclock Series Graphics Accelerator

GIGABYTE Gamer HUD Lite

The GIGABYTE Gamer HUD Lite allows you to adjust the voltage of your graphics card and the working

frequency of the GPU, Shader, and video memory.

(Note) This item is configurable only if 2D/3D Auto-Optimized is set to Disable.

Incorrectly doing overclock/overvoltage may result in damage to your system and reduce

the useful life of the system components.

Button Function

Default

(Note)

Allows you to load the default settings

Apply

(Note)

Allows you to save the values you adjust

Enable Lets the utility optimize the voltage and GPU/Shader/memory frequency

settings

Disable Allows you to manually configure the voltage and GPU/Shader/Memory

frequency settings

Hardware Monitor Displays the GPU usage and temperature, the GPU usage/thermal curve,

and your graphics card information

? Opens Help page

Clock adjustment

(Note)

Enables manual adjustment

of the

voltage/frequency

Automatically

optimizes the

voltage/frequency

Displays the

current operating

frequency

Hardware

Monitor

Help page

- 17 - Software Installation

You can move the slider to change the resolution.

You can click the item to change the color quality.

Click the Advanced button for advanced settings.

3.2. Display Properties Pages

Display Settings (Resolutions and Color Quality for Windows)

To access Display Settings page, right-click on desktop and select Personalize, then the Personalization

windows will show up. Select Display Settings to adjust the screen resolution and color quality settings.

- 18 -

Super Overclock Series Graphics Accelerator

Or you can right-click on the desktop and select Personalize, and then the Control Panel\Appearance

Personalization\Personalization window will show up. Select Display Settings. When the Display

Settings dialog box appears, click Advanced Settings.

After clicking the Advanced Settings button in Display Settings, you'll see the Generic PnP

Monitor and NVIDIA GeForce GTX 275/260 Properties dialog box. Click the GeForce GTX 275/260

tab to access the NVIDIA Control Panel.

3.3. Accessing NVIDIA Control Panel

After installation of the display driver, right-click on the desktop and select NVIDIA Control Panel. The

NVIDIA Control Panel is used to configure all your graphics card settings.

Right-click on the desktop and select NVIDIA Control Panel.

On the GeForce GTX 275/260 tab page, click Start the

NVIDIA Control Panel to launch the NVIDIA Control Panel.

- 19 - Software Installation

Select the view of the NVIDIA Control Panel that is

most appropriate for you.

 Standard Settings

 Advanced Settings

The following pages provide details on configuring

advanced settings.

In the NVIDIA Control Panel, select a category to

alter specific NVIDIA display settings.

The categories are:

 3D Settings

 Display

 Video & Television

In the NVIDIA Control Panel, change a view if you

want.

The supported modes are:

 Standard

 Advanced

 Custom

- 20 -

Super Overclock Series Graphics Accelerator

 Adjust Image Settings with Preview

If you are unfamiliar with 3D technology or not

an advanced graphics user, use the Adjust

Image Settings with Preview page to preview

any changes you make for improved image

quality and rendering.

 Manage 3D Settings

(Note 1)

The Manage 3D Settings page enables you to

establish default 3D settings to use for all your

Direct3D or OpenGL applications and to estab-

lish a unique set of 3D settings for a particular

game or application.

 Set SLI Configuration

(Note 2)

SLI technology allows you to use two or more

GPUs together. This results in significant im-

provements in rendering performance and

image quality.

Note:

It is recommended that you set to Enable SLI

technology to enhance the graphics card's

performance.

(Note 1) This item is present only in Advanced view mode.

(Note 2) This item will show up when you install two graphics cards with the same model name and

from the same vendor.

3D Settings

Tasks in the 3D Settings pages allow you to do the following:

• Change the image and rendering settings of your 3D applications and games that utilize Direct3D and

OpenGL technology.

• Override the shipped clocked frequencies of your GPU and GPU memory to increase your GPU

performance.

• Assign specific 3D settings to a game so that these settings automatically load when a game is

launched.

Page is loading ...

Gigabyte GV-N275SO-18I User manual

Brand: Gigabyte

Model: GV-N275SO-18I

Category: Graphics cards

Type: User manual

This manual is also suitable for

Download PDF

report

Gigabyte GV-N275SO-18I User manual

This manual is also suitable for

Gigabyte GV-N275SO-18I User manual

Related papers

Other documents