ZGG27120

GE ZGG27120 User manual

  • Hello! I am an AI chatbot trained to assist you with the GE ZGG27120 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
GE Monogram ®
Installation
Instructions
Stainless Steel
Professional Outdoor
Cooking Centers
48" Natural g'a,s mode£:
ZGG48N42
ZGG48N3 I
ZGG48N40
ZGG48N30
48" Liquid Ih'@a)_e model,s:
ZGG48L42
ZGG48L31
ZGG48L40
ZGG48I_30
36" Natural g'a,s modd, w
ZGG36N31
ZGG36N21
ZGG36N30
ZGG36N20
36" Liquid !'r@a_e modd, w
ZGG36L31
ZGG36L21
ZGG36L30
ZGG36120
27" Natural g'a,s modd, s:
, ,c _ c
ZG(,21N21
Z(,(,2 IN20
27 _'Liquid Propa_e model,s:
, ,c _ c
Z(,G21121
, ,c_ c
ZG(,2 zL20
Before wm begin--Read these instructions completely and careflllly.
IMPORTANT: Sine these instructions for local inspector's use.
IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES.
NOTE TO INSTALLER: Be sure to leave these instructions with tile Constm_er.
NOTE TO CONSUMER: Keep these instructions _dth your Use and Care Book for
ftlture reference.
If vou hme questions concerning tile
installation of this product, call tile GE
Answer Center ® (;onsumer hfformation
Serxice at 800.626.2000, 24 horn's a day
7 days a week.
If vou receix ed a damaged cooking center,
VOtl should contact VOIII" dealer.
Installation of this cooking center requires
basic mechanical skills, Proper installation is
the responsibility of the installer,
For Monogram local serxice in your area
1-800-444-1845.
For Monogram serxice in Canada,
1-888-880-3030.
For Monogram Parts and Accessories, call
1-800-626-2002.
FOR _r)UR SAFETY:
Do not use cooking center in a space where
gasoline or other liquids hming flammable
xapors are stored or used.
CAUTION:
For outdoor use only. Use this cooking center
only in the manner intended b} the man utacturer.
This outdoor cooking gas appliance is not
intended to be installed in or on recreational
vehicles arLd/or boats.
I)o not use the grill in an explosive atmosphere.
Keep the grill awa)/i:om areas where gasoline or
other tlammable liquids and vapors are stored or
being used.
()bser_e proper clearances to combustible
materials at all times.
I)o not use a rusty or damaged I_Ptank.
Never substitute gases (natural/or LP or I P tor
natural). These grills are tacto D set/or I_Por
natural gas. ()rder the model/or your installation
situation.
When storing the grill indoors, disconnect the I_P
tank. Store the tank outdoors in a well ventilated
area.
I)o not store additional I_Ptanks in or near the gas
grill.
Follow tile guidelines on tile I_Ptank tor proper
storage, transport and handling.
I,P models are supplied with a 20 lb. LP tank
(shipped separately) equipped with a Type 1 Acme
connector. The supplied regulator has a mating
coFtnector.
The supplied I _Ptank is equipped with an overfill
protection device. If }_)u utilize a tank exchange
s}stem, be sm:e to exchange this tank tor a tank
with the smn e de_ice.
IF "_g)/_5SMELL GAS:
Slmt off gas to appliance.
Extinguish any open flame.
Open lid.
If odor continues, immediately call vom"
gas supplier.
Tested in accordance with ANSI Z21.58 latest
edition standard tor outdoor cooking gas
appliances. This grill is tor outdoor use only.
Check local building codes tot the proper method
of installation in the absence of local codes, this
trait should be installed in accordance with the
National Fuel Gas Code No. Z223 latest edition
and the National Electrical Code ANSI!NFPA
no. 70, latest edition.
CAI JF()RNIA PROP()SITI()N 65 - \\;4RNING
Tile burning of gas cooking fuel generates some by
products that are on the list of substances which
are known by the State of Cali/ornia to cause
cancer or reproductive harm. Cali/ornia law
requires businesses to warn customers of potential
exposure to such substances. To minimize expo-
sure to these substances, always operate this unit
according to the use and care manual, ensuring
you provide good ventilation when cooking with
gas.
INSECT \\;hRN/NG!
Spiders and insects can nest in the burners of this
and any other grill, and cause the gas to flow/i'om
tile ti:ont of tile burner. This is a very dangerous
condition which can cause a fire to occtlr behind
the valve panel, thereb} damaging the grill and
making it unsatz "to operate. Inspect the grill twice
a year or immediately if any symptoms appear.
Contents
Models Axailable .................................................. 3
Accessories ............................................................ 3
Product Dimensions &-Clearances ..................... 4
Advance Planning ................................................ .5
Choosing the Ix)cation ........................................ 5
Tools & Materials Required ................................ .5
Step 1: Remove the Packaging ............................ 6
Step 2: Provide Support ....................................... 7
guilt-hi Installations ..................................... 7, 8
Step 3: Provide Gas & Electrical Supply ............. 9
LP Gas Models .................................................. 9
Natural Gas Models .......................................... 9
Ele_ trk al Supply ............................................. 10
Step 4: Test tor Leaks ......................................... 10
Step 5: (:he_k Burners,
Replace Drip Trays and (;rates ..................... 11
Step 6: I_ighting the Grill .................................. 12
Step 7: Adjusting the Burners ........................... 13
Install Rotisserie ................................................. 14
In stall Access Doors ........................................... 15
Design Infi)rmation
Ouldoor Cooki_g Ce_te*w
ModeLs
Available
Monogram Outdoor Cooking Centers are
tactorv set for LP or natural gas. Order the
model t0r your installation situation.
48" Natural gas models:
ZGG48N42
4 grill bm'ners, 2 rear infl'a red bm'ners
ZGG48N31
3 grill bm'ners, 1 rear infl'a red bm'ner, and
2 side bm'ners
ZGG48N40
4 grill bm'ners
ZGG48N30
3 grill burrJers, 2 side burrJers
36" Natural gas models:
ZGG36N31
3 grill burners, 1 rear infl'a red burller
ZGG36N21
2 grill buri/ers, 1 rear infl'a red burner, and
2 side btu'ners
ZGG36N30
3 grill bm'ners
ZGG36N20
2 grill bm'ners, 2 side bm'ners
27" Natural gas models:
ZGG27N21
2 grill btu'ners, 1 rear infl'a red bm'ner
ZGG27N20
2 grill burners
48" Liquid Propane models:
ZGG48L42
4 grill burners, 2 rear infl'a red bm'ners
ZGG48L31
3 grill burrJers, 1 rear infl'a red buriler, and
2 side bm'ners
ZGG48IA0
4 grill burners
ZGG48L30
3 grill bulTlers, 2 side bulTlers
36" Liquid Propane models:
ZGG36L31
3 grill bm'ners, 1 rear infl'a red bm'ner
ZGG36L21
2 grill btu'ners, 1 rear infl'a red btu'ner, and
2 side btu'ners
ZGG36L30
3 grill bm'ners
ZGG36L20
2 grill bm'ners, 2 side bm'ners
27" Liquid Propane models:
ZGG27121
2 grill burners, 1 rear infl'a red burner
ZGG27120
2 grill burners
Accessories
All models may be installed on a portable grill
cart or built into an enclosm'e. Enclosm'es can
be constructed of non-combustible (masonry)
material or of combustible material such as
wood. h_sulated jackets are required fiw
installation into combustible enclosm'es.
Grill Carts:
ZX48CTA, t0r 48" wide models.
ZX36CTA, tor 36" wide models.
ZX27CTA, tin" 27" wide models.
Insulated Jackets for Combustible enclosure:
ZX48J_SS, fin" 48" wide m odels.
ZX36]YSS, tin" 36" wide models.
ZX27.p, QSS,t0r 27" wide models.
27" Model Trim Kit
ZX27TK_QqS is m'ailable to conceal the gap
between the cooking center and enclosure.
ZXADCSS - Stainless Steel Double Access
Doors
ZXSDCSS - Stainless Steel Single Access Doors
Optional accessories to cover the access open-
ing trader the grill in a built-in installation.
Vinyl Covers:
Tough vinyl, telt lined with elastic bottom.
ZX48CVCY, fits all 48" models on cart.
ZX48CV4Y, fits 48" built-in's with 4 btu'ners.
ZX48CV3Y, fits 48" built-in's with 3 bm'ners.
ZX36CVCY, fits all 36" models on cart.
ZX36CV3Y, fits 36" built-in's with 3 burners.
ZX36CV2Y, fits 36" built-in's with 2 burners.
ZX27CVCY, fits 27" models on cart.
ZX27CV2Y, fits all 27" built-in models.
ZX2LYSS - Dual rmlge top burner - LP Gas
ZX2NYSS - Dual rm_ge top burner - Nat. Gas
Can be installed on the right side of a 27" cart.
For built in installations order Trim Kit
ZX2TKYSS to conceal the gap between the
side and rear edges of the opening.
Insulated jacket ZX2.]\_S is required for
installation into a combustible enclosm'e.
Design Inf_)rmation
Product
Dimensions
& Clea__ances
16-1/4'
Min.to Combustibles
3"ClearanceforLid
/
13-7/8"
24-3
2"
27" Wide Models
mbustibles
3" ClearanceforLid
36" Wide Models
Min. toCombustibles
47-7/8"
48" Wide Models
Design Infbrmation
Outdoor ( ooki_g C¢_ter,s
Advance
Planning
Mon(_gram Outdoor Cooking Centers are
designed to be installed on a grill cart or into
an enclostlre.
27" Models:
In a non-combustible (masonry) enclosure,
the grill drops into the opening. A deck (1i"
ledge on each side is required tk)r support
fl'om the bottom.
Insulated jackets are available to allow the
grill to be installed in a combustible
enclosure. The insulated jacket must be
supported fl'om the bottom bv a solid deck oi"
ledge on each side beneath the jacket.
If using a backsplash or rear wall, locate the
electrical seiwice fin" the rotisserie on the left
side.
• Trim kit ZX27TKS_qS is available to conceal
the gap between cooking center and the back
and sides of an enclosure.
36" and 48" Models:
In a non-combustible (masonry) enclosure,
the grill drops into the opening and hangs
fl'om its side flanges. A deck is not required
for support.
Insulated jackets are available to allow these
grills to be installed in a combustible
enclosure. The insulated jacket must be
supported fl'om the bottom bv a solid deck
or ledge on each side beneath the jacket.
If using a backsplash or rear wall, locate the
electrical service fin" the rotisserie on the
right side of the opening.
Clearances-All Models
• Allow 3" at the rear fin" lid clearance.
• Allow at least 12" clearance at the back of the
grill when exhaust is directed to a window or
a surthce that is difficult to clean.
• Allow at least 6" clearance on each side to
any non-combustible material located above
the cooking surthce tor counterspace.
Rotisserie models also require 6" clearance
tor placing and handling the motor and
skewer.
• Allow at least 12" clearance on each side and
rear to combustible vertical materials.
Choosin, g
the Location
• These cooking centers are designed for
outdoor use only. Do not locate the grill in a
building, garage or other enclosed area.
Ensure that fl'esh air ventilation is adequate.
Consider exposure to wind and proximity to
traffic paths.
• The minim um clearances to combustibles
must be maintained at all times.
Do not install a grill below overhead
unprotected combustible construction.
The installation lnust corJtorln to local codes
or in the absence of local codes, with the
national filel gas code, ANSI Z223 latest
edition.
The location lnust be level and stable.
7bols &
Materials
Required
(Not s_/¢died)
Phillips head screwdriver
Pipe wrench
I _evel
Flat blade screwdriver (3/32" blade)
Pliers
• Appropriate gas line to reach built-in
installation location
Pipe joint sealant, approved type and
resistant to LP gases
Manual shut-offvalve
CAUTION: All cooking centers are extremely
heax)'. 2 people are required fin" lifting and
placing the product into a cart or ellclosure.
Installation
Ouldoor Cooki_g" ( e_ler,s
Step
Remove the
P<_ckagi'ng
Open the box and remove packaging.
Open the grill lid and remove white plastic
tie-downs on b/irners.
Remove side burner grate and aeration pan.
Remove tie-downs on b/lrners.
Open the hardware accessoix carton and
check contents.
LPRegulator
Type1Acme,2B lb. LPtank
(LPmodels only)
Grill Grates
GourmetRadiantTMTrays
Rotisserie rod, handle, holders and motor ((m
models so equipped).
Spit Forks
Motor
36"/48" Motor
RotisserieRodandHandle
Natural GasRegulator
Coupler andNipple
(Natural GasModels)
1/2"NPTto 3/8 flare adaptor
<'///!! ! ! ! ! ! ! ! ! _'_\\\.',.',.\'_
Warming Rack(onsome models)
\
,,,,
\
,,,,
Match ",,,,
Stick "",,,,,
,,,,,
ExtensionRod
Models with side burners.
SideBurnerCover
SideBurnerAeration Pan
Installation
Outdoor Cooki_g Center,_
Provide
Support
Built4n
hl,stallation
All Outdoor Cooking Centers can be installed
on a cart designed specifically for that model
size. Follow the installation instructions
provided with the carts to install. Proceed to
(;as supply to complete the installation.
(:AUTION: The grill is heavy. 2 people are
required to lift and place tile grill into tile
cart or tile enclosure.
• All models may be installed into a
combustible or non-combustible enclosm'e.
Combustible enclosures require tile use of
an insulated jacket. Insulated jackets are
available as a optional accessory. Order tile
specific type flw yore" model.
Clearalces
• Allow 3" at tile rear t0r lid clearance.
• Allow at least 12" clearance at tile back of tile
grill when exhaust is directed to a window or
a s/irfilce that is diflictflt to clean.
• Allow at least 6" clearance on each side to
anv non-combustible material located above
tile cooking sm_hce for cotmterspace.
Rotisserie models also req tfire 6" clearance
tot placing and handling tile motor and
skewer.
• Allow at least 12" clearance on each side and
rear to combustible vertical materials.
2 7" Models
ZX27TKYSS Trim Kit
This kit is designed for both combustible and
non-combustible ench)sures. Tile trim will
conceal tile gap at tile rear and both sides of
tile opening.
Secm'e trim to tile sides and back with screws
provided.
Place tile grill into tile enclosm'e.
NOTE: This trim kit is not designed to
support tile weight of tile grill. Tile grill must
be supported fl'om tile bottom.
12"Min.to
InstallElectrical Combustibles
Outletfor Rotisserie Clearance
on LeftSide forLid
(6.5AMP Min.)
I/2"
InstallElectrical
Outletfor Rotisserie
on LeftSide 33-3
(6.5AMP Min.)
12"Min. to
Combustibles
Clearance
forLid
35-1/2"
10-1/2"
4x4Opening
pply
Line
Openingfor
AccessDoors
11-1/2"
Opening
forGasSupply
Line
peningfor
AccessDoors
27" wide models:
Installation in a non-combustible enclosure.
In a non-combustible (I//asonry) enclosure,
tile grill drops into tile opening. A deck or
ledge on each side is required for support
fl'om tile bottom.
27" wide models:
Installation in a combustible enclosure.
ZX27JYSS insulated jacket is required
• Tile insulated jacket must be supported from
tile bottom by a solid deck or ledge on each
side beneath the jacket.
Consti uct tile enclosure as shown and place
tile insulated jacket into tile enclosm'e. Place
tile cooking center into the jacket. No
installation hardware is required.
7
Installation
Outdoor Cooki_g Ce_tler,s
36" Modeh
12"Min. to Combustibles
3" ClearanceforLid
34-1
InstallElectrical
tisserie
OnRightside
(6.5AMPMin.
InstallElectrical
Outletfor Rotisserie
OnRightside
12"Min.to Combustibles (6.5AMPMin.)
3" ClearanceforLid _23-3/4"
40-1
35-1/2"
9-1/8"
penmg
for6asSupply
Line
"Openingfor
AccessDoors
10-1/8"
for GasSupply
Line
Openingfor
AccessDoors
48" Modeh
36" wide models:
Installation in a non-combustible enclosure.
36" wide models:
Installation in a combustible enclosure.
ZX36JYSS insulated jacket is required.
12" Min. to
Combustibles
3" Clearance
for Lid
InstallElectrical
Outletfor Rotisserie
OnRightSide
(6.5AMP Min.)
35-1/2"
12" Min. to
Combustibles
3" Clearance
for Lid
51-3
InstallElectrical
tisserie
OnRightSide
(6£ AMPMin.)
4x4Opening
forGasSupply
Line
OpeningFor
AccessDoors
10-1/8"
pening
forGasSupply
Line
Opening For
AccessDoors
48" wide models:
Installation in a non-combustible enclosure.
In a non-cond)ustible (masoniT) enclosure,
the grill drops into the opening and hangs
fl'om its side flanges. A deck is not required
for support.
48" wide models:
Installation in a combustible enclosure.
ZX48JYSS insulated jacket is required.
Combustible enclosm'es require insulated
.jackets. ZX3Q]'_L_S for 36" models and
ZX48]_2SS for 48" wide models. The
insulated jacket must be supported fl'om the
bottom bv a solid deck or ledge (m each side
beneath the jacket.
Consti uct the enclosm'e as shown and place
the insulated jacket into the enclosm'e. Place
the cooking center into the jacket. No
installation hardware is required.
Installation
Outdoor ( oohb_g Ce_ters
Provide
Gas &
E#ctrical
Suppl>,
PRODUCT ST() [_4(;E
When storing LP models indoors, discon-
nect the LP tank. Store the tank outdoors
in a well ventilated area.
Do not store spare LP tanks in or near tile
Otltdoor Cooking Center enclosure.
LP GAS MODELS
Com_ect tile regulator/Quick Cmmect
assembly to the hose attached to the grill.
• Tile Quick Cmmect type coupling requires
the user to pull on tile outer sleeve of tile
timbale coupling while simultaneously
inserting tile male hose end into tile coupling,
then release tile locking outer sleeve.
To cmmect the tmlk:
Insert tile coupler sleeve on tile regulator over
tile tank inlet, turi1 clockwise to tighten.
To disconnect the tm_k:
• Tm'n off tile main tank valve.
Grasp tile coupler sleeve and ttlrn cotlnter-
_ hreadingCompoundMustBe
Resistantto L.P.Gas
L.P.RegulatorQuick
DisconnectHose
Assembly
Coupler Sleeve
Inlet ve
LP operating pressm'e is 10" W.C.
(:AUTION: The LP tank (shipped separately)
clockwise. Remoxe tile inlet from tile opening, is a Type 1Acme. Do not attempt to change
or alter these supplied parts Do not attempt
to use tile regulator/hose assembly with a
standard 510 POL tank/valve assembly.
NATURAL GAS MODELS
Tile grill and its individual shut-off valve nlust
be discmmected fl'om tile gas supply during
any pressm'e testing of tile system at test
pressm'es in excess of 1/2 PSI(;.
Tile grill must be isolated from tile gas supply
system by closing its individual sh m-off valve
dm'ing any pressm'e testing of tile system at
test pressm'es equal to or less than 1/2 PSIG,
The installation of these grills must conform
with local codes or, in the absence of local
codes, with the National tirol gas code, ANSI
Z993 latest edition,
Operating pressm'e is 4" W.C.
Supply pressm'e should be 5" to 14" W.C. If
pressure is more than 14" _\(:. a step down
regulator is required.
Check with local gas utility or with local codes
_()i"instructions on installing gas supply lines.
Be sm'e to check on type and size of rim and
how deep to bm'v the line. If the gas line is too
small, the grill will not fimction properly.
(
c0uper /
to 3/8" FlareFitting_Natural GasSupply
InstallerSuppliedj
Shut-Off
Install a mmmal gas shut-off valve in an easily
accessible location.
Use threading compo/md on male threads
onlv. Do ilOt use threading compo/md on
tile male end of tile 1/2 NPT to 3/8 flare
adapter.
Make connections as shown,
Check to be sure the regulator arrow points
in tile direction of gas flow, towards tile grill
and away fl'om tile gas supply.
Installation
Outdoor Cooki_g (enters
ELECTRICAL SUPPLY
Models with rotisserie require 120V, 60Hz.
and cmmected to an individual properly
grounded branch circuit protected by a 15
amp circuit breaker or time delay filse.
The power cord on the rotisserie is equipped
with a three-prong (grotmding) plug which
mates with a standard three-prong grotmding
wall receptacle to minimize the possibility of
shock hazard fi_om this appliance.
If the electrical service provided does not
meet the above specifications, it is recom-
mended that a licensed electrician install an
approved outlet.
DO NOT UNDER ANY CIRCUMSTAN(:ES,
CUT OR REMOVE THE THIRD (GROUND)
PRONG FROM THE POWER CORD.
For 27" wide built-in grills, locate the
electrical outlet on the left hand side within
reach of the rotisserie's 72" power cord.
For 36" and 48" wide built-in grills, locate
the electrical outlet on the right hand side
within reach of the rotisserie's 30" power
cord.
St
es[Jo "
Leaks
TEST FOR LEAKS
A complete gas tightness check must be
pertormed at the installation site.
Do not use the grill tmtil all com_ections have
been leak tested.
• Repeat leak test alter each LP tank change.
Check to be sm'e the main valve on the LP
tank or the shut-off valve is in the "OFF"
position.
• Make a soap solution of one part liquid
detergent and one part water.
The valve panel must be removed to check the
valves and fittings.
• All control valves should be in the "OFF"
position.
• Relnove the knobs.
On inodels equipped with Rotisserie, relnove
the satety valve pushbutton and tmsrrew the
stn'rotmding bezel.
• Rem()ve the 4 screws holding the valve panel
to the grill.
• Pull the panel outwards and m_plug the wires
fl'om the back of the rotaI T igniters.
If the grill has an optional rotisserie bm'ner,
remove the screws holding the inspection
cover in place.
TO TEST:
Apply the soap solution arotmd the
com_ections, valve and tubing.
Tm'n the gas supply on.
Check all comaections fi'om the supply line
or LP tank up to and including the manifl_ld
pipe assemblv.
If a leak is detected, turn gas supply to off
and tighten fittings. Tm'n the gas on and
check again.
To re-install the valve panel, re-comaect the
igniter wires and secm'e the panel with
original screws.
10
Installation
Ouldoor Cooki_g" ( e_Her,s
5
Check Burner, s,
Drip 7 ays
and G' ates
:2 IN
iii ii i
i'i _ i
I
iii i i !_
,il i I
i i !
i'i
/ iil
During shipping parts, such as burners and
reflectors may haxe mined. Check to be sure
all parts are in position.
Remove tile smoker tray (if so equipped).
Check to be sm'e smoker bm'ner and
deflector plate are installed properly, The
bm'ner and plate should be placed over the
holding pin at tile back and fl'ont of tile grill.
CORRECTBurnerRests
LevelontoAnti-FlipBracket
--- Anti-Fli
Bracket
INCORRECT
Burneris
UpsideDown
ould
beonTop
Check to be sm'e all b/irners are in tile correct
position. Bm'ners should rest fiat over tile anti-
flip brackets with stubs on top and fiat side
(l()IV I1,
Check to be sm'e that all grill bm'ners are
level and secm'elv seated in the grill box.
Place Gom'met radiant on top of each
burner. (:lips on tile bottom of tile radiant
fits over stubs on the bm'ners, It should be
centered in the grill box fl'ont to rear,
Place the grill grates over the opening,
Slide drip tray into place,
11
Installation
Outdoor Cooking (enters
Lighting
the Grill
Do not attempt to
light tile grill if tile odor of gas is present.
CAUTION: Keep hands and thce as t_u"away
from tile grill as possible when lighting.
Open tile lid and remove tile side cooktop
b/irller cover.
• Turn all knobs to "OFF" position,
• Turn gas supply on at the LP tank or shut-off
wdve,
NOTE: When lighting the burner fi)r the first
time (11"after a LP tank change, allow up to 20
seconds to purge air fl'om tile lines.
• Push and turn control knob to "LITE"
position, immediately turn the rotai y igniter
knob next to tile burner knob.
NOTE: Tile spark will produce a snapping
sound. This is normal.
If tile burner does not light within 4 seconds,
turn knobs to "OFF" and wait 5 minutes t()r
tile gas to dissipate beti)re trying again.
If tile burner does not light after several
attempts, tile burner can be lit with a match.
A match stick extension rod is provided on
SOllle Illodels.
TO MATCH LIGHT:
Insert a match stick DO NOT LIGHT)
securely into tile clip end of tile match stick
extension rod,
Light tile match stick held on tile end of tile
rod and hold against a burner port towards
the fl'ont,
Push and turn tile corresponding control
knob to tile LITE position.
If tile burner does not light after 4 seconds,
turn tile knob OFF. Wait 5 lninutes for any
accumulated gas to dissipate befl)re trying to
light tile burner again.
All burners may be match lit in tile same
lllanner,
If tile match light extension rod is not
provided with your model, refer to tile
(hvners Manual ti)r lighting instructions.
12
Installation
Outdoor Coohb_g (enters
Ste 7
Adjusting
the Burners
A_!jusm_ents should not be required, unless
vibration during transit or variations in local
gas supply make minor a_!justments necessary.
Ac!justments must be made by a qualified
technician at tile time of installation. Extreme
care should be used if ac!justments are made
after installation.
• Turn gas supply on.
Push and turn tile burner control knobs to
tile "LITE" position. Up to 20 seconds may
be required to to purge air fl'Oln tile lines.
Flames should be blue and stable with no
yellow tips, excessive noise or lifting fl'om tile
burner. If any of these conditions exist turn
control to off and check air shutter and
burner ports for debris or spider webs.
TO ADJUST:
Remove burners by lifting and twisting while
pulling towards tile back.
Locate and loosen tile lock screw on tile time
of tile air shutter with a screwdriver.
Replace tile burners.
• Turn burner knob to tile "LITE" position.
If tile flame is yellow, indicating insufficient
air, ttlrn tile air shtltter open to allow more
air to tile burner.
\
\
\
If tile flame is noisy and tends to lift away
fl'om tile burner, there is too much air. Turn
the air shutter to reduce tile opening.
Side b/irners can be ac!justed in tile salne
11/an n er.
Low setting Adjustment:
Minor a_!justments may be required due to
fluctuations in local gas pressure. Ac!justments
to increase or decrease gas flow may be
necessar V,
• Turn burner knob to "LITE" position.
• Turn tile control knob to tile lowest setting,
all tile way counter-clockwise.
Remove tile knob by pulling straight out.
Insert a thin-blade fiat screwdriver into tile
valve shaft and hold. (3/32" blade width
recolnln ei_ded.)
Grip the shaft with pliers and tm'n the
screwdriver counter-clockwise to lower the
flame, or clockwise to increase the flame.
• When the desired setting is made, replace the
knob and turn burner off.
NOTE: Ac!justment of tile illfra-red rotisserie
b/lrner is not recoi//i//ended,
Beze[_
Valve Stem
WARNING:
Always check tile low flame size fl_r stability. A
burner flame which is too small may go out or
be extinguished easilv. This can cause un-
burned gas to escape and cause a hazardous
condition.
13
Installation
Ouldoor CookD_g Ce_ter,s
hzstaU
Rotis_serie
((/so _,q_i/,i,,,cl)
27" Wide Models:
Slide the motor down into the channel on
the lett side and tighten thumb screw.
• To use, place pointed end of the skewer into
the motor, mad the threaded end resting on
the right side support.
Remove the handle fl'om the threaded end
of the skewer befiwe using.
36" and 48" Wide Models:
The motor will rest on the cast iron block
and can be tightened against the grill by
turning the black knob.
To use, place pointed end of the skewer into
the motor, and the threaded end resting on
the right side support.
Remove the handle from the threaded end
of the skewer befiwe using.
14
Install Access Doors
Outdoor Cooki_tg" ( e_tler,s
hi, stall
Optional
Access Doors
ZXAI) CSS
or
ZXSI)CSS
\\
\
The opening fiw double and single access
doors should be 24-1/8" wide and 18-1/4"
high.
Place the fl'ame into the opening and secure
with screws on all sides.
Hang the doors on the hinges as shown.
1.5
Monogram °
Gene_l_ecrricCompany
Lousy#re, KY40225
Note: While performing installations described in this book,
safety glasses or goggles should beworn.
7;_obtain _peciflc i_ffinmalion com:erni_g ahr
Monogwzm pwducl or service5 _zdl(_EAnswer C_ozter_;
consu*mn i_lfinm(zHo_l se*wi : al 800. 626.2000_a_ 0
time, d( 0 m nigfiL
F_n Mon_g*gzm k)_aI s_.*_6.,i_ your ar*,a, _all
1-800-444-184 5.
NOTE: Iho(h_ct impl ox emem is a c(mmmmg elide ivoi al Gellelal
I_lecllic _'l_ele_le, malerials, appearaJ_ce and specificalioJ_s are sul!iect
to chaJlge wuholll J_o_ice
Pub. No. 49-80009
Dwg. No. 164D3333P227
(0 2000 (E Appliar_ces
Printed in [SA
(N.D. 537) 7,/00
10743
/