2. Computers & electronics
  3. Audio & home theatre
  4. CD players
  5. Soundmaster
  6. UR 2080

Soundmaster UR 2080 Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Soundmaster UR 2080 Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
DE 1
Deutsch Nederlands
English Espańol
Français
UR 2080
GB - 1
LOCATION OF CONTROLS AND INDICATORS
Front view
Bottom view
1. AUX IN, ON Button
2. Timer Indicator
3. Timer Start/Stop Button
4. TimerAdjust–/+Buttons
5. CD Door
6. CD Tray Open / Close Button
7. CD Stop / Off Button
8. CD ON, Play / Pause Button
9. AUX IN Jack
10. Remote Sensor
11. Radio Preset Up / Down Buttons
( / )
12. Radio On / Band Button
13. LCD Display
14. Volume - / + Button
15. Clock Button
16. CD Mode / Program Button
17. CD : Skip/Search Previous
 Radio:Tuning–
 Time:Time–
18. CD : Skip/Search Next
Radio : Tuning +
Time : Time +
19. Speakers
20. AC Power Cord
21. Battery Compartment Door
22. FM wire Antenna
CDK108 UR2080 ib 37.indd 1 2010/4/28 2:43:02 PM
GB - 2
Remote control
1. Volume - / + Button
2. CD : Skip / Search Previous
Radio : Tuning –
3. CD : Skip / Search Next
Radio : Tuning +
4. Radio Preset Up / Down Button
( / )
5. Radio On / Band Button
6. AUX IN, ON Button
7. Mute Button
8. CD ON, Play / Pause Button
9. CD Stop / Off Button
10. Magnetic Plate
11. Battery Door
LOADING BATTERIES
1. Remove the battery compartment cover.
2. Insert 2 "AAA" size batteries (not included) as indicated by the polarity marking. (Placing
the battery in the wrong way will cause malfunction.)
3. Replace the battery compartment cover.
Note:
• The batteries (battery pack or batteries installed) shall not be exposed excessive heat
suchassunshine,reorthelike.
•
Donotattempttorecharge,short-circuit,disassemble,heatorthrowthebatteriesintoare.
• If you don not intent to use the remote for a long time, so you must remove the batteries
to prevent damage by leakage and corrosion.
• When the distance from which the remote conrol will work gets shorter than before, replace
all batteries with new ones. Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium).
• Do not try to recharge batteries not intended to be recharged; they can overheat and
ruptune. (Follow battery manufacturer's directions).
• Dispose of old batteries properly in accordance with local law.
OPERATION
Basic operation is same as main unit, except :
1. PRESET UP - recall radio preset station up within the selected band.
2. Mute - mute the audible sound from loud-speaker, LCD will show "MUTE", press this
button again to resume audible sound.
Use of Magnet
The magnet is attached on the back of the remote control. You can put the remote control
on an iron or steel surface such as on a refrigerator.
User should not attempt to operate the remote control while it is attached to iron/steel
surface.
Note : Do not place the remote control near magnetic cards such as credit cards.
CDK108 UR2080 ib 37.indd 2 2010/4/28 2:43:02 PM
GB - 3
PREPARATION FOR USE
INSTALLING THE UNIT UNDER A CABINET
1. Mark the position of the 3 holes by using the supplied template. Use a drill to make the
holes.
2. Whenthecabinetdooroverhangstheshelfandobstructstheunit,youcanadjustthe
unit/shelf height.
3. Install the unit with the supplied mounting screws.
Caution:
Please read the following before installing the unit.
• Since the unit is heavy, be careful when installing the unit.
• Toreducetheriskofre,donotplaceanyheatingorcookingappliancebeneaththis
unit.
• Install the unit so that its AC power cord can be connected directly to a wall outlet. Do
not use a converter or extension cord.
• Be sure that the AC power cord has no slack when using the unit. If the AC power cord
has some slack, wind it up to the cord hook until the cord has no slack.
• The unit has a built-in ferrite bar antenna for AM radio reception. Check the condition of
AMreceptionbeforexinginposition.
• Install the unit as far as possible from a source of noise. (for example, refrigerator,
microwaveoven,uorescentlamp,etc.)
• Use tools carefully while installing of the unit.
• Toreducetherishofre or electricshock,donottouchtheACpowercordwithwet
hands.
CDK108 UR2080 ib 37.indd 3 2010/4/28 2:43:04 PM
GB - 4
MAIN POWER SUPPLY
- Check that the power voltage as shown on the type plate (at the base of the set)
corresponds to your local power voltage. If it does not, consult your dealer or service
organization.
- Connect the power cord to the wall outlet, for AC power supply. As soon as you insert the
powerplugintothewalloutlet,thedisplaytimewillashandshow . Please see
below how to set the correct time.
POWER FAILURE
If power failure occurs, the unit will switch off. As soon as the power supply returns,
willashanddisplay,indicatingthatyoumustresetthecorrecttime.
BATTERY BACK-UP SYSTEM
2 "AA" size batteries (not included) can be inserted into
the battery compartment to, in the event of a power failure,
providesufcient powerto maintainthetime. WhenAC
power is restored, the correct time will be restored and will
not require resetting.
• Neither the display nor the unit will operate until the unit
is connected to an AC outlet.
BATTERY WILL ONLY
RESTORE CLOCK SETTINGS WHEN AC POWER IS
RESTORED.
• Replace the battery once per year. The service of the battery depends on how often and
for how long the power supply fails. This varies from one region to another.
Note: Always check the time and reset if necessary after a power-failure.
CLOCK
Setting the current time at power off mode
1. Press and hold CLOCK button for a few seconds.
 Atonewill sound andthehour digitwillstart to ashonthe
display.
2. PressTUNE/TIME+or–buttonuntilthecorrecthour.
3. Press CLOCK once. A tone will sound and the minute digit will
ash.
4. Repeat step 2 to set the minutes.
After setting the minutes, press CLOCK. Two tones will be heard and normal operation
will begin.
Tosetthecurrenttimerapidly,holddownTUNE/TIME+or–.
CDK108 UR2080 ib 37.indd 4 2010/4/28 2:43:05 PM
GB - 5
COMPACT DISC OPERATION
TIPS ON HANDLING COMPACT DISCS
Discs should be handled with care. Dirt, dust, scratches and warps can cause the sound to skip during
playdeterioratingthesoundquality.Thefollowingguidelineswillhelpensuremaximumenjoymentfrom
your CD collection:
• Onlyusediscsbearingtheaudiocompactdiscidentication
logo.
• During non-use periods, always store CDs in their protective
case.
• To keep discs clean, always handle by the edge. DO NOT
touch surface, stick paper on surface or stick tape on its
surface. Fingerprints and dust should be carefully wiped off
with a soft cloth. Wipe in a straight motion from the inside
out.
• Do not use cleaning chemicals such as: benzine, thinner,
alcohol, cleaning or anti-static sprays. These may
permanently damage the disc's plastic surface.
• Do not write or stick anything on either side of the disc,
especially the non-label side.
• To prevent wapping of the disc, do not expose it to direct
sunlight, extreme temperatures, heat sources, or humidity
for any extended period of time.
• Dirty, scratched or warped discs may cause skipping or
noise.
CAUTION
TO AVOID DAMAGE TO YOUR DISC AND/OR PLAYER,
ALWAYS MAKE SURE THE DISC HAS FULLY STOPPED
ROTATING BEFORE OPENING THE DISC COMPARTMENT
DOOR.
INSERT WITH
THE LABEL
FACING UP
PRESS THE CLAWS
AT THE CENTER OF
THE DISC CASE.
PRESS THE
DISC GENTLY
TO INSERT IT
LIFT OUT WITHOUT
TOUCHING THE
RECORDED SURFACE.
INCORRECT
CORRECT
FROM THE CENTER TO THE EDGE
INCORRECT
CDK108 UR2080 ib 37.indd 5 2010/4/28 2:44:36 PM
GB - 6
CD PLAYER OPERATION
1. Press PLAY/PAUSE button once to turn on CD power, "CD" will light up on the
LCD.
2. To open the CD tray, press OPEN/CLOSE button once.
- NOTE : Pressing the OPEN/CLOSE button at any time will automatically switch the unit
to the CD function and open the CD tray EXCEPT when the timer alarm is sounding.
3. Place a compact disc on the tray with label side facing upward.
4. To close the CD compartment, push OPEN/CLOSE button once.
- The CD player scans the contents of the CD and the total track number
will be displayed.
5. If no CD inside, LCD will show "no".
6. Press PLAY/PAUSE button to start playback from track no. 1. The
display will indicate the playback track number.
7. AdjustthesoundlevelbypressingVOLUME+/–buttons(Maximum
volume is "20").
8. To pause playback, press PLAY/PAUSE button.
Press PLAY/PAUSE button again to resume playback.
9. Press STOP button to stop playback.
10. To switch off the CD power, press the STOP button again.
Note : CD playback will also stop when :
- The CD has reached the end.
- The CD door is open.
- The RADIO or AUX IN button is pressed once.
SKIP/SEARCH ( or )
Selecting a different track during playback.
- Youcanjumptothenexttrackbypressing button once. If you want to skip more
than one track, press button more than once until the display shows the desired track
number.
- If you want to repeat the current track from the beginning, press button once. If you
want to play one of the previous track, press button more than once until the display
shows the required track number.
Starting with a particular track
1. In the STOP mode, you can select a desired track using the or button.
2. Press PLAY/PAUSE button to start playback.
Searching for a passage within a track
You can search for a passage within a track. The CD audio sound will be muted during
search track.
• Keep the or button pressed during playback, and release the button.
- Normal CD playback will resume from this point.
CDK108 UR2080 ib 37.indd 6 2010/4/28 2:44:47 PM
GB - 7
CD MODE/PROGRAM
REPEAT 1
- During CD playback, press CD MODE / PROGRAM button once. The REPEAT 1 indicator
will come on and the current track will play repeatedly.
REPEAT ALL
- During CD playback, press CD MODE / PROGRAM button twice. The REPEAT ALL
indicator will come on and all tracks will play repeatedly.
RANDOM PLAY
- During CD playback, press CD MODE / PROGRAM button three times. The RDM indicator
willashandtrackswillbeginplayinginrandomorder.
PROGRAM
Programming track number at STOP mode.
You may store up to 20 tracks in the memory in any sequence.
You may store any track more than once.
1. Press the CD MODE / PROGRAM button, the PGM indicator ashesand is
shown.
2. Press or
to select the desired track
3. When the desired track is displayed, press CD MODE / PROGRAM button to register.
The next program no. display will change to .
4. Repeat step 2 and 3 to program the order of more tracks up to 20 tracks can be programmed
into memory.
Program Play
Press PLAY/PAUSE
button, the PGM indicator will turn on and start to play the desired
tracks.
To clear programmed tracks
- Press STOP button before program play, or
- Press STOP button twice during program play, or
- Open CD door or
- Press RADIO ON/BAND button once
AUX IN OPERATION
Caution: Turn off power and unplug the power cord before connection.
Connect to other audio equipment, including video recorder to provide sound output
for other audio equipment.
Preparation
1. Connect these audio equipments "LINE OUTPUT" to "AUX IN" socket
of the unit through an audio cable (not included).
2. Press the AUX IN / ON button once to turn on power and into AUX
IN mode.
3. The AUX indicator will light up on the LCD.
4. Press VOLUME +/- button to increase or decrease sound level.
5. To turn the unit off after use, simply press the STOP/OFF button
once.
CDK108 UR2080 ib 37.indd 7 2010/4/28 2:44:49 PM
GB - 8
RADIO OPERATION
1. Press RADIO ON/BAND button once to turn on radio power, RADIO will
light up on the LCD.
2. Press RADIO ON/BAND button again to select radio band.
3. PresstheTUNE/TIMEbutton+or–momentarily(lessthan0.5sec.)tostepupordownthereceiving
frequency in order to select the desired station.
4. Forautotuning,keeppressingtheTUNE/TIMEbutton+or–(morethan0.5sec.)untilthedisplayed
frequency starts to change, then release the button. Tuning will stop automatically when a station is
received.
5. AdjustthesoundlevelbypressingVOLUME+/–buttons.
6. To turn the unit off after use, simply press STOP/OFF button once.
NOTE: After radio frequency is displayed for about 10 seconds, the LCD will show the current time.
Pressing the RADIO ON/BAND button once will show radio frequency again.
Improving the reception
• Extend the FM wire antenna which is located on the back of unit, and change its position until the
best FM reception is found.
• The unit has a built-in ferrite bar antenna for AM radio reception. Check the condition of AM reception
beforexingthisunitinposition.
• Install the unit as far as possible from a source of noise. (for example : refrigerator, microwave oven,
uorescentlamp,etc.)
PRESET STATIONS
1. Press the RADIO ON/BAND button to the desired band.
2. When the desired station is tuned, press CD MODE / PROGRAM button
to enter saving mode.
3. ThepresetlocationwillashontheLCD,pressPRESET / button
to select preset channel.
4. Press CD MODE / PROGRAM button again to save into memory. If it has previously set, the former
station is replaced.
5. Repeat step 1 ~ 4 to store more preset stations.
NOTE: The preset memory can store a maximum of 12 stations for FM band and 12 stations for AM
band.
RECALL A PRESET STATION
To recall any preset stations within the selected band, simply press the PRESET / buttons until
the preset radio frequency appears on the display.
TIMER OPERATION (Count-down timer)
• TIMER SETTING
- PressTIMERADJUST+or–todesiredcount-downtime,themaximum
count-down time is 120 minutes, with a 1 minute interval selection.
- Press the TIMER button once to start counting, the timer indicator will
light up.
- When the timer has been set and is counting, the LCD will show the count-down, however, current
time, radio frequency and CD playing track can also be displayed by pressing:
1. CLOCK button once to show current time and CD playing track when unit is in CD play mode.
2. CLOCK button once to show current time when unit is in radio on mode.
3. RADIO ON/BAND button once to show current radio frequency when unit is in radio on mode.
4. CLOCK button once to show current time when unit is in stop/off mode.
• About 5 seconds later, LCD will resume to show timer count-down.
- To cancel timer operation, simply press TIMER button once, the timer indicator will turn off.
- When desired time has elasped, refer to below section for details.
CDK108 UR2080 ib 37.indd 8 2010/4/28 2:44:51 PM
GB - 9
• Timer can be set and operated in OFF mode or CD PLAY / RADIO ON / AUX IN mode.
- In OFF mode:
 Whenthedesiredtimehaselapsed,abeepsoundwillbeheardandthetimerindicatorwillashfor
about 60 minutes. This alert can be stopped at any time by pressing the TIMER button once.
- In CD PLAY / RADIO ON / AUX IN mode:
 Whenthedesiredtimehaselapsed,abeepsoundwillbeheardandtheTIMERindicatorwillash
for about 60 minutes. When the alarm sounds, the sound level of CD PLAY / RADIO or AUX IN
will be lowered automatically. This alert can be stopped at any time by pressing the TIMER button
once. When the alert stops, the sound level of CD PLAY / RADIO or AUX IN will return to the original
level.
SPECIFICATION
RADIO SECTION
FrequencyRange FM:87.3–108.1MHz
 AM:522–1620KHz
CD SECTION
Sampling Frequency 44.1 KHz
Frequency Response 80 Hz - 16 KHz
POWER SOURCES
Mains Operation AC 230V ~ 50Hz
Clock Standby System DC 1.5V x 2 "AA" (not included)
Power Consumption 15W in AC operation
GENERAL
Speaker 2 x 76mm 4 ohms
Power Output 2W + 2W
Dimension Approx.330 (W) x 70 (H) x 260 (D) mm
Weight Approx. 2.2 kgs. w/o batteries
DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
CDK108 UR2080 ib 37.indd 9 2010/4/28 2:44:51 PM
/